Search Documents

By Gregg R. Gitschlag

There are more than 4,000 oil and gas structures present in the U. S. Gulf of Mexico. Approximately 100 structure removals occur each year and 66% of these are removed with explosives. From 1993-1995 an intensive study was conducted on the fish kill resulting from the explosive removal of 6 platforms off the Louisiana coast in water depths from 14-28 m (45-92 ft). After explosives were detonated, all floating fish and a sample of the dead fish which sank to the sea floor were collected.

Jan 1, 1997

By Xue Yongpeng, Zhu Zhenhai, Zhu Ming

The purpose of the Solid Medium Controlled Blasting Technique and Its Applications is to have the inside of the vessel-shaped framework (e.g: oil tank , water pool, gas chamber, chimney, water tower, grain warehouse and etc.) or the one side of the thin wall-shaped structure(e.g: steel bar concrete wall and etc.), both of which are intended to be demolished, inserted with the required solid medium (e.g: soil , sand , coal, salt and etc.) ,in which there is a certain mass density, and then through which the blasting energy is transferred to fulfill the blasting task. For such a technique, it is necessary to bury the explosives into the inserted solid medium and then to start the explosion to blast the intended target into pieces. The filling of the solid medium may be done mechanically or by man. Compared with the water pressure blasting technique, this one has the characteristics of good effect. wide application, simplified construction procedure , safe and reliable operation and small vibration (less vibration than water pressure blasting by 80% to 90%)in particular without any flying stones, thus resulting in better and comprehensive social and economickfficiency.

Jan 1, 2000

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By L. Muñoz, L. Steffen, J. Alarcón, W. Vilas

Today, mining operations close to communities face increasing challenges, especially in their drilling and blasting operations. Proper management of environmental impacts is important to guarantee their license to operate and to provide sustainability to the mining business in the long term. Blasting is an event that generates impacts such as vibrations, noise (airblast), projections (flyrocks), ejection of dust and fumes (when there is a deficient detonation of the explosive). If any of these variables exceed the established regulations, sanctions can be generated and even lead to stop mining operations. The goal of this work is to present a review of different techniques, concepts, technologies, simulation software and monitoring / control tools to minimize the environmental impact generated by blasting. For which, a case study of a big scale open pit mine in Brazil with operations close to a community will be presented. An adequate management model, combined with good operational practices, the use of new technologies, enable a safe operation without incidents with the communities. In this way, building trust with neighbours, maintaining the license to operate, and helping mining industry to mobilize resources essential for progress in a sustainable way

Jan 1, 2024

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coot-tha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency, and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1995

By George D. Raitt, Rudy Lyon

Until fairly recently, Down-The-Hole (DTH or DHD) hammer drilling was never really a factor in large scale open pit surface mining. It was a method confined to water well drillers, aggregate quarries and limestone mines where the hole size rarely exceeded 6-1/2" (165 mm). Also it was somewhat limited to the harder rock areas such as the North East and South East United States. The trend in the big mining pits for coal, copper, gold and iron, was for the big rotary drill rigs with lots of muscle in pulldown, bitload and rotary torque.

Jan 1, 1998

By Thad M. Jones

This paper considers the sampling, digitizing and reconstruction of seismic signals. A sampling frequency range is proposed and a minimum limit is suggested. Digitizing precision criteria for both peak velocity and analysis applications are given. Several methods for reconstructing signals from sampled data are presented.

Jan 1, 1985

By R Frank' Mammele Chiappetta, Conny Postupack

A major problem that has continued to plague the surface coal industry is blast induced damage to the coal seam. Atlas Powder Company has addressed this situation through seven years of field research in full-scale production environments. Many operations across the United States have been evaluated.

Jan 1, 1988

By M. Oguz Ozkazanc, Gulsev Uyar Aldas

Because of its safety, being easy to handle, relatively inexpensive and containing a lot of energy, ANFO is the most popular and widely used explosive in Turkey as well as other countries in the world. According to change dated May 14th 1999 on the regulation 87/12028 related with explosives, blasters are not allowed to mix ammonium nitrate and fuel oil in the tield to make ANFO. Instead of this, they have been forced to use the ready ANFO prepared by explosive producer firms. As a result of this obligation, the use of technical nitrate for agricultural purpose and mixing AN and fuel oil in unsuitable conditions have been prevented. Indeed, wrong mixture means waste of energy and money.

Jan 1, 2001

By Dan McCutchen, Oettmeier

Kelly bar drilling and blasting is unique to Florida, the' Bahamas and other marine limestone areas in the world where blast holes are required but will not remain open for the loading of explosives. This type of rock formation usually yields 1.5 tons of recoverable rock compared to 2.2 tons per cubic yard for competent limestone. The loss of .7 tons per cubic yard is due to voids and sand in the formation. These deposits all contain water to the top of the blast holes which are collared only a few ft. above the ground water level. The working pit is a water filled lake which is excavated from the bank by draglines. These drills have been used in Florida for many years to depths of 65 ft or less.

Jan 1, 1991

By Wilfrid Comeau

Vibrograms, which last significantly longer than the actual blast (say 10 to 15 cycles or more), may be signalling an elastic response, which is not uniquely blast related. For example, geophones mounted on a part of a structure, which can elastically resonate at a frequency included in the seismogram, may not show the structure’s real reaction to the blast. This resonance usually amplifies the ground vibration. This contribution examines one particular case where blasting excited and amplified a resonant ground response, and the method used to significantly reduce or eliminate this undesirable condition.

Jan 1, 2007

By R J. Hill

Blasters are well aware of the problems and expense faced when trying to load in wet bore holes; problems of poor coupling and poor density, as well as the expense of higher priced cartridge product. In answer to these problems, I developed a system for dewatering using nozzles with lay -flat plastic liners which I have used successfully over the last few years. I found the system not only gave me better shots than I could have expected in the circumstances, but also dramatically decreased costs. The system has been adopted by two large roading contractors and a quarry operation in Eastern Canada.

Jan 1, 1986

By Robert B. Hopler

This paper reviews, from the historical standpoint, the development of the commonly-used terms such as "No. 6 and No. 8" with regard to detonator strengths. The origin of the strength terminology is reviewed, and the many methods developed to compare the strength of one detonator to another are described, with the good and bad points of each method outlined. The "miniature cartridge test," very highly regarded by both the U.S. Bureau of Mines and Institute of Makers of Explosives in the 1930's and early 1940's, is described in detail, as is a test developed and used by IRECO.

Jan 1, 1992

By Curtis G. Kremer, Jeffrey L. Brummert

Blue Circle Cement's Ravena, New York quarry mines approximately 6.7 million tons of limestone per year. Blasting occurs approximately twice a week on three separate benches. Shots average 60,000 tons but can range up to 140,000 tons. Ongoing scrutiny of the drilling and blasting program allows for maximum blast efficiency which results in lower overall mining and crushing costs. Close cooperation between management and explosives supplier assures Blue Circle Cement's objective, "To develop, implement, and continuously improve a measurable drilling and blasting system that will optimize the total mining and crushing costs while ensuring compliance to safety and maintaining or reducing the environmental impacts of blasting".

Jan 1, 1994

By RR Vandebeek, A W. Bauer

The Canadian Explosives Research Laboratory regularly evaluates the properties of commercial explosives for authorization under the Canada Explosives Act. Propagation sensitivity is normally measured using small scale tests. Relating the results in actual mining practice is difficult. In the mining industry, the propagation sensitivity is a measure of the ability of one cartridge to propagate to an adjacent cartridge in a borehole. They may be separated by a gap of in-filling material. As well the propagation sensitivity will be affected by the explosive type, temperature, degree of coupling, cartridge diameter and other factors.

Jan 1, 1987

By Q Liu, P D. Katsabanis

The energy output of crushed AN/FO, crushed AN/FO mixed with Aluminum (5%, 6.4% and 9.4% A1 by mass) and a commercial emulsion explosive has been measured using a detonation calorimeter. The charges had a diameter of 10 mm and were heavily confined by a 11 mm thick copper shell. In order to achieve stable detonation glass microballoons were used in the explosives so that the density of the AN/FO charges would be around 1.1 g/cc. The charges were detonated in vacuum and the detonation products were analyzed using gas chromatography. It was found that energy values were very close to calculated values obtained by ideal detonation codes.

Jan 1, 1993

By D G. Dressler, Paul Yeager

A previously little-known facet of seismic frequency spectrum analysis is gaining significance. The frequency spectrum of seismic waves promulgated from blasting is a significant factor in causing blasting complaints and threshold (architectural type) damages.

Jan 1, 1987

By Thomas E. Ricketts

An important part of underground mine planning and operations involves the reclamation of working areas after blasting before the mining cycle can continue. This is especially true for mining that must use large blasting operations in the vicinity of extensive underground workings. In an effort to develop a rational procedure for estimating mine damage produced by blasting, underground rock fall has been assessed for a large-scale blasting operation in oil shale. The amount of mine damage has been quantified in terms of manshifts of effort required to reclaim underground working areas after blasting. This has been further broken down into the three main phases of reclamation, i.e., scaling and excavation, rockbolting, and miscellaneous repairs on ventilation, utilities, etc. Different types of openings have also been assessed including level tunnels, incline drifts and rooms. The effect of repeated blasting on mine damage has also been documented with initial blasts producing more damage than subsequent blasts.

Jan 1, 1988

By Virgil J. Stachura, Larry R. Fletcher, Paul V. Sterk, Matthew N. Plis

The large diameter blastholes now being used in underground mining have caused concern because of their increased potential for damaging openings and creating rockfall hazards. In response to this situation, the Bureau of Mines is conducting research to reduce the amount of overbreak and damage to the perimeter of underground openings. This paper presents the results of tests with decoupled charges in 6.5 inch diameter blastholes, and unloaded guide holes, in Vertical Crater Retreat (VCR) stope panels at the Homestake underground gold mine in Lead, SD.

Jan 1, 1991

Case histories in blasting show that Livingston's cratering technology has been applied successfully to blast designs with explosives having a charge length to diameter ratio not larger than 6. But the evaluation of experimental results such as the crater volume is tedious and sometimes impractical. A key analysis presented in the study shows that the optimum scaled volume relates well with the optimum scaled rupture limit, and the latter can be determined by means of high speed photography without excavating the blasted material. Through the studies of harvesting gypsum from a dried up settling pond the high speed photography approach has demonstrated to be effective for determining the optimum design for blasting plastic material.

Jan 1, 1987