Search Documents

By Scott Gustfason, Richard N. Snyder

What is a safe stand-off distance? Recent mishaps using conventional blasting equipment have seen flyrock as distant as 3,750 feet from the blast area, or close to three-quarters of a mile, therefore, whether below ground, under water, in surface quarries or at a structural demolition site, data signals riding a radio wave promise a new horizon for the users of both electric and non electric blasting circuits.

Jan 1, 1987

By N. Paley

An engineering project was undertaken at the Cominco Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by blasting differently. The Julius Kruttschnitt Mineral Research Center (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast design to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed and the powder factor increased to maximize fines. However, JKMRC research had shown that it appeared possible to increase primary breakage by blasting to such an extent that SAG mill throughput could reach a plateau or even begin to decrease. Modeling was carried out on a range of blast pattern geometries and emulsion explosive blends to determine if a plateau existed and at what powder factor it would be reached. It was found that the relationship between powder factor and grinding throughput was nonlinear. Modeling was also used to compare the SAG mill throughput which could be expected from different emulsion explosive blends to determine which blends should be used in dry and wet holes to provide similar fragmentation. For heavy-ANFO mixtures, the highest modeled throughput was at a ratio of 30/70, with ratios on either side indicating lower throughput. For emulsion blends, the highest modeled throughput was at a ratio of 80/20; however, ratios from 80/20 to lOO/O were similar. Crusher product size distributions were obtained from belt cuts early in the analysis to confirm model predictions. At later stages, actual SAG mill throughput was compared to predicted. The economic benetit from the different blast designs was calculated by accounting for the reduction in recovery due to the higher throughput and the additional drilling and blasting costs. Increasing the powder factor by 150% from the 0.29kg/t {0.58lb/st] being used to 0.72kg/t { 1.44lb/st}, the maximum feasible with mine equipment, could provide a sign&ant net benefit of $3OWyr due to the increased concentrate production. However, because the relationship between throughput and recovery is affected by other factors which were not modeled, a more conservative approach was taken. The powder factor was instead increased by 50°h, providing 45% of the gain. This was possible because the relationship between powder factor and grinding throughput was nonlinear.

Jan 1, 2001

By Joshua Hoffman, Catherine Johnson, Braden Lusk

Blasting conducted in surface coal mining operations in the Appalachian region consumes a significant amount of blasting agents. Emission of oxides of nitrogen (NOx) from these operations potentially represents an environmental challenge. This paper presents work conducted to quantify NOx output from the detonation of blasting agents common to surface blasting operations in surface coal mines. Annual ANFO and emulsion consumption data was collected from an operational surface coal mine located in West Virginia. It is known that many factors contribute to the types of gaseous byproducts released from the detonation of explosives. These factors include but are not limited to: fuel to oxygenator ratio, degree of confinement, and contamination. While, past research has been conducted to study the relationships these factors play on the release of NOx, these findings do not agree with one another. The annual explosive consumption values from the West Virginian mine were applied to NOx emission conversion factors in published literature. This lead to a range of NOx emissions from 95 to 914 tons in a year. Given the wide range of NOx production the utility of this information is suspect. The EPA recognizes a standard factor of 17 lbs (NOx)/ton (ANFO) however this factor is based on chemical composition and does not address contamination, confinement, or AN to FO ratio. This factor when applied to the West Virginia Mine's explosive consumption produced a value of 215 tons of NOx. There is a lack of information on NOx emission from emulsion type explosives. The work presented in this paper can be used by blasting professionals to quantify NOx emissions and guide future work for producing better predictor factors.

Jan 1, 2014

By Dale L. Ramsey

Blasters in the field for years have been faced with the task of plotting blast locations for future reference and calculating scaled distances or seismograph placement from maps,aerial photo's etc.'With the constellation fully operational, GPS provides a satellite signal transmitted to a ground receiver which will display the desired coordinate positioning worldwide, 24 hours a day in any kind of weather conditions. There are a variety of GPS receivers available with varying levels of accuracy. The field trials of a handheld navigational quality instrument for plotting blast and seismograph locations along with other necessary industry related data is the basis of this paper.

Jan 1, 1994

By J Lyall Workman, Peter N. Calder

The Manassas Quarry is a large industrial stone quarry in Northern Virginia owned and operated by Vulcan Materials Company. The quarry experienced instability in a portion of the north wall, which included toppling failure in a metasediment and movement on a major fault zone. It was necessary to take remedial measures to stabilize the wall and create good quality final pit walls.

Jan 1, 1992

By Detlef Sulzer, Winfried Rosenstock

"At the end of this century a great breakthrough in the field of blasting technology is finally going tobecome reality. That, in the true sense of the word, is the long expected and desired “HighTechnology Blasting”. So far trials have been carried out in Australia, Africa and Europe with remarkable results, that have been predicted by the authors. As a result, significant reductions of explosives and drilling expenditure are emerging for the future."

Jan 1, 1999

By Michael S. Wieland

The work-principle method was developed for theoretically resolving toxic fumes from non-ideal charge formulations. The whole description of a wanted process refers to macroscopic changes resulting from removing and imposing constraints that work one at a time to chronologically render trajectory terminal (key) states. The trajectory resolution utilizes a thermodynamic quasi-potential or negative work function, and numeric results require some appropriate standard thermodynamic (equilibrium) reaction code TDRC. The underlying method is unable to restrict reactions, tailor the work output or resolve states within the trajectory transitions, so the trajectory terminology is used somewhat figuratively. The work-principle model has the working fluid (reaction material) interacting with a tremendous reservoir (chamber air and walls), while forecasting the work performed upon a mechanical agent.

Jan 1, 1998

By Qi Jinduo, Gong Min

On the basis of actual parameter of wall control blast in Nanfeng mine, China, the process of dynamic stress changing between two column charges was studied recently for a presplit-cushion blast by holographic photoelasticity. In the experimental model, two holes were simultaneously detonated from both ends (four ignition points). The bottom of the holes were loaded more than other parts (heavy charge). Under these conditions, four consecutive isochromatic fringe patterns at different times were acquired in one loading run, and the characteristics of the stress distributions were compared at different places and times in the holes. It was found that interaction types of stress waves vary along the holes. The theory is posed that the stress wave which is formed by the interaction of earlier producing P wave and later S wave along a distributed line charge is the most important part in all stress waves. Research indicates that a heavy charge in the bottom of the holes is crucial to producing a presplit-cushion effect at the bottom. "End Effect" doesn't affect the magnitude of stress along linking lines between the bottoms. The chief fields of the "End Effect" are also explained in the paper.

Jan 1, 1998

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d’Or, Quebec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By Catherine T. Aimone-Martin, Susan G. Beattie

A series of small scale explosive tests were performed at a perlite mine near Socorro, New Mexico. The tests were designed to investigate the azimuthal or directional relationship between small scale geologic structures such as joints and the propagation of explosively-induced ground motions. Three shots were initiated within a single borehole located at ground zero at depths varying from 83 m (272 ft) to 10 m (32 ft). An array of three component velocity and acceleration transducers were placed in two concentric rings at distances of 20 m (66 ft) and 40 m (131 ft) surrounding the single hole at 7.5° , 15° , and 30° azimuths as measured from ground zero. Data from the transducers were then used to determine the average propagation velocity and waveform characteristics of the blast vibration through the rock mass at the various azimuths. The rock mass was mapped to determine the predominate joint orientations (strike and dip) and the average propagation velocities were correlated with this geologic information. The results showed that there is a correlation between the predominate joint orientation and ground motion amplitudes and velocity. The more predominate geologic structures allow the wave to follow along their strike thereby forming a planar path of least resistance and in turn, allowing higher velocities and amplitudes. Secondary joints or structures may act in concert with more prominent features to form a network of channels or paths along which the wave moves more freely than it may when traveling against the structures. The greatest azimuthal variations in velocity and amplitude was observed for the shallow shot at 10 m (32 ft) depth.

Jan 1, 1996

By J Edmund Hay

Previous work by the Bureau of Mines to develop a test for determining the initiating strength of commercial detonators has been modified and extended. Recently reported results by the Bureau used a homogeneous liquid explosive to avoid the complicating effects of inhomogeneities; however, due to the belief that there may be essential differences between the initiation mechanisms of simple liquids and multi-phase mixtures and the fact that almost all commercial explosives are in the latter category, the experiments have been modified accordingly. The acceptor explosive is now a mixture of explosive-grade ammonium nitrate (AN) prills, methanol (MeOH) and nitromethane (NM). An additional change has been the use of the United Nations (UN) cap sensitivity test configuration in which the detonation witness is the degree of compression of a lead block, which is a quantitative measure of the response of the explosive. Results indicate that this mixture has sufficient range of sensitivities to be useful in comparing the strength of commercial electric detonators.

Jan 1, 1993

By Thomas E. Lobb, Harry C. Verakis

Blasting is a primary means of extracting minerals and ores at surface mining operations. The domestic consumption of explosives and blasting agents during the year 2001 was about 5.25 billion pounds. Flyrock is always a major concern for the blaster. Flyrock from surface blasting operations has caused serious injury and death to employees and other persons. Injuries due to flyrock and the lack of blast area security accounted for over two-thirds of all blasting-related injuries in surface coal, metal, and nonmetal mines during the period 1978-2002. Selected accidents due to flyrock and lack of blast area security in surface mining are presented in this paper. Incidents related to construction blasting are also described. Techniques to mitigate blasting accidents are discussed. These include proper blast design, driller-blaster communication, inspection prior to loading and firing the blast, removing employees from the blast area, controlling access to the blast area, and using a blasting shelter. An experienced driller could detect potential problem areas such as voids, mud seams, incompetent rocks, and other irregularities by observing the progress of drilling. The drill log should include the details of any unusual or exceptional circumstances noticed during drilling. A blaster may need to alter the loading configuration to alleviate potential problems. Basic blast design is sometimes taken for granted and assumed to be proper for the conditions encountered, but one size does not fit all. It is known from the physics of blasting that the explosive energy takes the path of least resistance. The path of least resistance could generate flyrock, depending on the blast site conditions. A combination of ‘borehole tracking’ and ‘laser profiling’ can assist in improving the design of a blast. The blaster can use these tools to adjust borehole loading to match site conditions.

Jan 1, 2004

By Mark S. Stagg, Stephen A. Rholl

The Bureau of Mines is studying blast delay timing influences on rock fragmentation in a series of tests that started in 3-ft concrete blocks, progressed to 45in-bench reduced-scale tests in massive dolomite, and has now included 22-ft-bench full-scale tests in a thin-to-thick horizontally bedded dolomite. This paper discusses the full-scale test results and how they compared to the concrete block and reduced-scale studies.

Jan 1, 1988

By Mark D. Kirkbride

This paper outlines the process for designing a hard rock blast in an underground coal mine. The coal mine is located in Western Kentucky and operates four continuous miner units at 7 unit-shifts per day. The mine operates in the Western Kentucky No. 11 Seam with local variations from 4.5 - 5.5 feet seam thickness. The seam has sporadic siderite deposits. Usually these deposits do not significantly interfere with the mining process. When previous siderite deposits were encountered they were small enough to drop an entry for a couple of crosscuts. The blasting plan was called for after a siderite deposit was encountered in the belt entry at about one third of the panel length. The other sides of the panel had been previously mined and sealed so the decision was made to mine through the siderite deposit with the continuous miner instead of abandoning the panel. The deposit was approximately 300 feet in length down the belt entry. Mining through the deposit with the continuous miner was expensive in both terms of production and of wear and tear on the continuous miner. A blasting plan for the siderite deposits was designed to minimize damage to the continuous miner should a similar situation occur.

Jan 1, 1999

By John Petty, John Loviza

Single sentence describing content-- "The best ally an Explosives Engineer can have in a court of law is a regulations enforcer stating all codes and standards were met on a jobsite".

Jan 1, 1996

By Roger N. Prescott

This report presents a new process in delay blasting with the use of ANFO and slurry explosives.

Jan 1, 1977

By Sheila Luchansky, F M. Babcock, Daniel M. Sanders

A cooperative effort between a blasting vibration consultant, a blasting contractor, and personnel from the City of Las Vegas has dramatically reduced complaints from residential areas near developmental blasting projects. The principal methods used involved the preparation of an informative video recording which presents various aspects of the blasting operations, the design of a distinctive flyer which is attached to residential doors, and pre-blast meetings for information dissemination.

Jan 1, 1993

By G Dean Barrett

Just one year ago at the 1986 Annual Meeting of the Society of Explosives Engineers, Dr. Calvin J. Konya presented a paper entitled "Presplitting Granite Using Pyrodex, A Propellant.'' Since that time more evidence has been developed to support the concept that "...gas energy can be the principal splitting force and that the stress wave or shock wave is not necessary to cause the presplitting action to occur." Work done in Vermont and Georgia is presented, and the ability to split granite without causing radial cracking of the bore holes is demonstrated.

Jan 1, 1987

By Paul Worsey, Randall Franklin

This paper is based on an undergraduate research project undertaken for the explosives emphasis in the UMR mining engineering degree program by the first author. The purpose of the selected research topic was to investigate the impact sensitivity of commercial detonators to determine their relative safety for handling and how much abuse they can take without accidentally firing. A modified BAM tester was used for the investigation. Both electric and non electric detonators were impacted at incremental positions along their length to determine the relative effect of their various components. Repeat impact tests were also conducted to see how a damaged cap would react to repeated abuse. The results indicate that it takes a significant amount of impact energy to initiate commercial detonators. They also indicate that repeated abuse can increase sensitivity. Modern commercial detonators appear to be relatively insensitive to impact (an order of magnitude above RDX in the standard BAM test) and this is mainly due to their construction. This explains why damaged caps with exposed powder are more sensitive. Their measured insensitivity correlates with rough handling not being a major cause of blasting accidents.

Jan 1, 2004

By Sandra K. Penttinen

A difficult blasting project can go very smoothly when every precaution is taken prior to and during the blasting procedures. These precautions include conducting careful preblast condition surveys of nearby structures, initiating a good public relations program prior to the beginning of the blasting, and following a good safety program during the blasting procedure.

Jan 1, 1994