Search Documents

By Yang Zhao, Tao Xiu-xiang, Chen Song-jiang

"China is rich in low-rank coals that account for 45.68% of existing coal reserves in China. The clean and efficient utilization of low rank coals is of great significance for ensuring the effective energy supply and promoting economic development and environmental protection. In order to solve the difficult problem in flotation of low rank coal, it has become the focus of research in the related field that oily bubbles instead of air bubbles are taken as a carrier in flotation to improve the attachment efficiency and recovery of low rank coal. In this paper, low rank coal slime collected from Shendong mining area was used as the experimental material, and it focused on the characteristics of oily-bubble flotation process of low rank coal. Additionally, difference in conventional flotation and oily-bubble flotation was discussed. The induction time between air bubbles, oily-bubbles and fine low rank coal particles was measured. The results indicated that the induction time between oily-bubbles and coal particles was obviously lower than that of air bubbles. By comparing the foam height of air and oily bubbles, it was found that the amount of oily bubbles is less than air bubbles, causing relative low flotation rate of oily-bubble flotation at initial stage. Besides, the maximum foam height and half-life of air bubbles and oily-bubbles were measured respectively. The results showed that the stability of oily-bubbles was higher than that of air bubbles, which is benefit for the enrichment of concentrates. The clean coal water recovery of oily-bubble flotation is lower than that of air bubble flotation, which indicated oily-bubble flotation is lower in water entrainment. INTRODUCTION China is the largest energy consumer in the world, accounting for 23% of global energy consumption in 2016 and 27% of global energy consumption growth. Whereas coal is taken as the major primary energy source and its share of China’s primary energy consumption is 62% in 2016, in which the low rank coals, such as lignite, long-flame coal, weakly caking coal, and non-caking coal, accounted for about 50% of total coal production capacity (China’s energy market in 2016, BP). Moreover, the exploitation and utilization of low rank coals and other coals that are difficult to float have been an important strategy for China’s sustainable development of the coal industry (Liu et al., 2014). However, the combustion of low-quality coals leads to a serious environmental pollution. In addition, the deterioration in geological conditions of coal resources, and the increasing improvement in the mechanization for mining significantly caused the increased amount of fine coal."

Jan 1, 2018

By S. M. Wen

In mineral processing, the settling of mineral particles in water, the flow of ore pulp, the dewatering and filtering of concentrates and so on, are related to the pulp viscosity. While the interaction between mineral particle surface and water affects directly the pulp viscosity. Therefore, it is of great value to the development of mineral processing theory to research the effect of mineral particle surface on the water viscosity in boundary layer. In micro-fluid, the effect of mineral particle surface on the water molecules in boundary layer can not be ignored. The water viscosity in boundary layer and the effect of the nature of mineral particle solid surface on the viscosity are analysed based on the deduction of attraction potential energy formula of mineral particle surface to the water molecules in boundary layer. The results show that the attraction potential energy of mineral particle surface to the water molecules in boundary layer is determined by the properties of solid molecules and fluid molecules and varies inversely as the third power of the distance from mineral particle surface. The water viscosity in boundary layer consists of the viscosity of free water and the additional viscosity resulting from the attraction of mineral particle surface. The increment of the viscosity caused by the attraction of mineral surface is µs. This additional viscosity is also inverse ratio to the third power of the distance from mineral particle surface. The greater the dipole moment, the polarizability and the ionization energy of mineral particle solid surface molecules are, the higher the attraction potential energy of mineral particle surface to the water molecules and the water viscosity in boundary layer are. The thicker stationary water boundary layer is d0. The higher the µs is, in other words, the greater the attraction of solid surface to water molecules is, the thicker the stationary water boundary layer becomes when free water viscosity is constant.

Jan 1, 2014

By Claudio L. Schneider, Peter R. King, Reiner Neumann

"Predicting the liberation spectra that are produced from breakage of two-phase ores under the random fracture assumption can be accomplished by measuring the conditional, on length, linear grade distribution directly from images obtained from a representative sample of the unbroken texture. The technique tremendously simplifies the prediction problem by avoiding the multiple convolutions that arise from the traditional method based on a description of texture from a measurement of the chord length distributions associated with each phase in the unbroken texture. For a 3-phase system, the phase transition probabilities associated with the textural information make the traditional calculation an almost insurmountable mathematical problem. The direct measurement procedure on the other hand can be expanded to three phases comparatively easily.A coal sample is used here to demonstrate the procedure. It is concluded that the conditional, on length, linear grade distribution can be predicted in the same fashion for multi-phase systems. Accurate stereological conversion is the practical hurdle to be overcome for multi-phase systems, but it is already a reality for 3- phase systems."

Jan 1, 2003

By T. C. Alex

Mechanical activation of gibbsite [?-Al(OH)3] is the theme of this paper. Industrially prepared gibbsite used in the study has a mono modal size distribution with a median size, d50=110 µm. Mechanical activation of this gibbsite has been carried out in a planetary mill at ambient conditions. Mechanical activated gibbsite samples are characterised in terms of particulate characteristics, structural characteristics and reactivity. As a result, of milling, mono modal size distribution of the unmilled gibbsite changes to a broad multimodal distribution. Size reduction has been sharp in the initial stages of milling; median size reduces to ~7 µm during 15 min of milling. Thereafter no decrease in median size is observed; rather it is found to increase gradually with further increase in milling time, indicating particle aggregation. Morphological studies of milled gibbsite have shown that the platelets forming the agglomerate are separated first; the separated platelets then undergo breakage. Aggregation of particles sets in the later stages of milling as a result of increased surface area and surface energy. X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies have clearly revealed the changes in gibbsite structure during milling. Analyses of XRD data show that the crystallite size of gibbsite decreases as the milling time progresses whereas its microstrain is found to increase. Accumulation of energy in the structure is the result in both cases. TEM micrographs with signs of defects leading to disordering of gibbsite structure complement the XRD results. Reactivity of milled gibbsite, decrease in its deydroxylation temperature and increase in alkali dissolution, is found to increase with mechanical activation. Increased reactivity of milled gibbsite is found to have a strong correlation with the BET specific surface area. Keywords: mechanical activation, gibbsite, alkali dissolution, thermal dehydroxylation, reactivity

Sep 1, 2012

By O. A. Bascur

It is difficult to analyse the economics without an integrated view of mine transactions, stockpile inventories, process flows and assays. The lack of integration of mining and metallurgical information with sufficient detail to analyse and act is a problem. However, to take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. Validation methods use process models to identify inconsistent information in the case of corrupt actionable information. This paper presents new strategies that transform the data into business information for continuous improvement and optimization. This technical presentation will review recent implementations enabling large metallurgical complexes to improve their data quality for overall production and energy management. A competence center emerges as an enabler for implementing operational intelligence. The evolution of Web services to troubleshoot plant information and to collaborate at the enterprise level is presented.

Jan 1, 2014

Vanadium-titanium magnetite from Panzhihua was crushed with open and closed circuit process by high pressure grinding roller (HPGR). The particle size characteristics of the crushed product were analyzed and the micro-cracks generated by HPGR during the crushing process were studied. The results showed that, in crushed products, the reduction ratio increases and the size distribution becomes more uniform with increasing of the pressure on roller?s surfaces. The fine fraction content of crushing products from -3.2 mm classification closed-circuit by HPGR increases obviously compared with that by Jaw Crusher and particle size distribution is more uniform. Large amount of intra-crystalline cracks and cleavage cracks are generated in vanadium-titanium magnetite crushed by HPGR, which makes the specific surface area larger and Bond grinding work index (objective particle size is 0.074 mm) decreased by 14.05% than that by Jaw Crusher. And the liberation degree of monomer of the product crushed by HPGR increased compared with that by Jaw Crusher with the similar fineness of grinding. Keywords: iron ore, high pressure grinding roller, micro-crack

Sep 1, 2012

By C. Çelik

Nowadays the optical sorting of industrial minerals is one of the most important processing methods which has cost efficient production possibilities. This method is used for industrial and raw materials that have different colour and brightness features. Initially this technology is used for sorting of foodstuffs and recovered glass, but for a long time also as physical mineral processing method for both industrial minerals like: limestone, marble, talc, basalt, flint, quartz and secondary raw materials like: building rubble, refractory materials, glass, plastic and household waste. In this study via optical sorting the separation of quartz out of a flint mix, which consists of the particles with different colors and brightness, is aimed. Experiments are performed on an optical sorting machine named CombiSense® 1200 at the institute of ?Aufbereitung mineralischer Rohs-toffe? RWTH Aachen. This automatic picking device was developed by the company ?Separation Systems Engineering (SSE), Wedel?. Hand picking method is used for product analysis and the efficiency tables are prepared on every step accordingly. This process enables to reach quartz products with purity up to 100%.

Jan 1, 2014

By S. J. Ma

To look into the ionic release laws of the sulphide tailings in some copper mine, the effects of the soaking period, temperature, oscillating speed, and pH of the solution on the heavy metals ionic re-lease were investigated through static soaking leaching experiments. The results show that Cu2+, Zn2+, Pb2+, Cr3+ are of different leaching behaviors with soaking period. The ionic concentration in soaking solution for four ions has a great gap. Zn2+ is more easily released out of sulfide tailings than Cu2+, Pb2+, Cr3+ , and the ion release concentrations are not proportion to their contents in the tailings. The time for each ion to reach its maximum concentration are different. The minimum concentration do not occur at the first day. Each ion concentration shows different fluctuation characteristic during soaking process. Solution pH, oscillating speed, and temperature affect the releases of Cu2+, Zn2+, Pb2+, Cr3+ out of the tailings to different extent. The effect of pH value on ion re-lease for the four ions ranks as Zn2+>Cu2+>Pb2+>Cr3+, the oscillating speed ranks as Pb2+>Zn2+>Cu2+>Cr3+, and the temperature ranks as Cr3+>Pb2+>Zn2+>Cu2+.

Jan 1, 2014

By S. Leroy

Grinding is the most energy consuming step in mineral processing, however, it is still poorly understood and its efficiency is difficult to monitor. Mill performances are traditionally measured at the mill discharge, on the basis of a mass percentage passing a certain sieve. This approach does not reflect what happens to the fines through milling. On another hand, if many macroscopic parameters, such as the percent solids of the pulp, its viscosity, or its mean residence time in the mill are known to be related to grinding efficiency, the link between these parameters and particle size distribution (PSD) is still unclear. Here, a methodology is established to understand the effect of ball mill operating conditions on particle size and shape distribution in the grinding process. The study focuses on the particular case of an Upper Group 2 (UG-2) platinum ore concentrator. Due to the very low grade of sulphide and PGM (Platinum group metals) in UG-2, grinding mechanisms are entirely control by gangue minerals. These two minerals have contrasted properties and PGM content and these properties immediately affect the entire recovery process. So, the grinding of both gangue minerals is studied on a size by size basis. At particle scale, three parameters are addressed: particle size, particle composition and particle shape. The specific behavior of chromite and silicate grains is demonstrated. As a conclusion, this study gives some clues to operate ball mills in a more efficient manner regarding chromite issue in the processing of UG-2. Keywords: ball milling control, UG-2, chromite, fine particle, particle shape, segregation

Sep 1, 2012

By N. Vasumathi

Most of the Iron ore washing plants set up in India in the earlier days consist of sizing of the ore by dry / wet screening, washing and classification by screw classifiers. In this classical approach, iron values were lost in the form of fines and ultrafine into the tailing ponds as they had little commercial value in those days and accumulated in huge quantities over the years. As the high grade deposits are getting exhausted and the demand for high grade finer material for pellet making is ever increasing, focus is shifting towards recovering the values from the erstwhile tailing ponds by column flotation. This is also supposed to mitigate to a certain extent the environmental problems caused by the ever expanding and unmanageable tailing dams. A case study is presented wherein a composite sample is prepared from samples drawn systematically from multi - locations in a sprawling tailing dam. Laboratory scale column flotation tests on this composite tailings sample, basically originating from two operating iron ore beneficiation plants of JSW Steel Ltd., one of the leading producers of steel in India are found to be encouraging. Desliming followed by reverse and cationic flotation tests using flotation column resulted in the concentrate of 61.88% Fe, 4.81% SiO2, 2.52% Al2O3 and 3.30% loss on ignition (LOI) from the tailings analyzing 57.86% Fe, 7.10% SiO2, 3.52% Al2O3 and 6.14% LOI with 52% weight recovery. The causes for the quality improvement could be attributed to desliming of un-liberated ultra fines of kaoline and hydrated iron oxides and their further reduction by efficient flotation process. The process and the cationic collector developed for this purpose are adopted in the new flotation plant created to treat these tailings. Keywords: iron ore, washing, ultra fines, tailings pond, column flotation

Sep 1, 2012

By J. W. Ahn

Calcined calcium oxide from limestone is hydrated to manufacture calcium hydroxide, and then precipitated calcium carbonate is synthesized from calcium hydroxide. Precipitated calcium carbonate of various morphologies is obtained by controlled conditions of each step and characteristics of limestone, calcium oxide and calcium hydroxide. Especially characteristics of calcium hydroxide have the most influence on morphology of precipitated calcium carbonate character. In this study, therefore, it is investigated the specific surface area of calcium hydroxide and morphology of precipitated calcium carbonate according to hydration temperature. Calcium hydroxide hydrated at high initial temperature has larger particle size than that hydrated at low initial temperature. And formation yield of aragonite precipitated calcium carbonate has improved by using calcium hydroxide had larger particle size (hydrated at high initial temperature).

Jan 1, 2014

By H. Deng

Oxidized zinc ores are the main source of zinc metal except sulfides. To have a better understanding about the performance of smithsonite and the main gangue, quartz, in flotation, the aggregation behaviors of smithsonite and quartz in water were confirmed by different techniques (sedimentation tests and optical microscopy). The experimental results show that smithsonite and quartz particles aggregate in the pH range 7.5-11. The results of zeta potential suggest that the aggregation does not correlate with the DLVO theory, when the iso-electric point of smithsonite and quartz is 8.0 and 2 respectively. When the solution pH is less than 8.0, smithsonite has an opposite charge to the quartz particles. Electrostatic adsorption makes effort on these two kinds of particles according to DLVO theory. Whereas, solution chemistry calculation shows the pH range 8-11 corresponds to hydroxide formation, suggesting that this is the species responsible for aggregation. And their concentrations are much higher in sodium hydroxide system than that in sodium carbonate system. Aggregation of smithsonite and quartz due to the flocculation action of zinc hydroxide is proposed.

Sep 1, 2012

The value creation with kaolin clays depends on removing the colored impurities which manifests in to higher brightnessone of the most sought after properties on applications such as paper coating, paint and others. The processes for removing impurities include magnetic separation, froth flotation and selective flocculation. While the flotation and selective flocculation processes exploit the physico-chemical differences between the surface properties, the magnetic separation uses the bulk magnetic susceptibility differences between the diamagnetic clay and ferro- and para-magnetic nature of the impurities. The major advantage with magnetic separation remains high yield and no or low reagent usage. However, the magnetic separation technology suffers from low separation efficacy when finer colored impurities (<1 µm) are encountered in the feed. Use of stronger magnetic intensities during magnetic separation showed limited success; nonetheless the adverse effect due to finer size range remains a dominant effect even at 5 Tesla magnetic field. Furthermore, the presence of diamagnetic colored impurities irrespective of their sizes can not be removed. Cytec Industries has recently developed a ?bolt-on? chemical enhancement technology for magnetic separation that essentially embraces the best product performance attributes of flotation and selective flocculation while keeping the chemical usage to a minimum level and using the readily available magnetic separation equipment. The paper will outline the technology and illustrate optimization work at pilot plant magnet on a wide variety of crude accommodating the process needs and plant limitations. The major advantages of chemical enhancement technology to magnetic separation include: 1) simple extension to existing magnetic separation technology, 2) ability to produce comparable product in quality with cost effectiveness compared to flotation and selective flocculation, 3) removal of impurity minerals over wide size range, 4) removing non-magnetic impurities, 5) providing robust process with high process yield and 6) operation-friendly nature. Furthermore, chemical enhancement technology for magnetic separation has also emerged as a platform for re-moving impurities at low levels in other mineral systems as well.

Jan 1, 2014

By P. Spolaore

In the frame of Bioshale FP6 project, the bioprocessing of a polymetallic and polymineral concentrate produced in an industrial operation in Lubin, Poland, was assessed. Following successful batch culture tests, processing in continuous conditions was tested to determine the main specifications for the application of the stirred-tank technology to this sulphide concentrate from black shale ores. The experimental work was carried out in a laboratory-scale unit consisting of 3 stirred tanks (50L or 20L) using an acidophilic and moderate thermophilic bacterial population. Different configurations of the unit and key operating parameters were tested (nutrient medium composition, solids concentration, rates of agitation and aeration). Scientific and technical approaches, such as bacterial community structure and mineralogical analysis were implemented in order to better understand the chemical and biochemical reactions occurring in the system. Using the data produced during the continuous operation, downstream processing assessment for both copper and silver recovery was also carried out. The best copper recovery obtained in the continuous operation was 92% and a hot brine leaching of the bioleach residue (PLINT process) allowed to recover 92% of the silver. A preliminary tech-no-economic evaluation of Lubin concentrate bioprocessing including bioleaching, copper and silver recoveries demonstrated the potential economic feasibility. Recovery of silver plays an important role in the economy of the process. This study presents promising values to further investigate this bioprocessing option.

Jan 1, 2014

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By Q. X. Li

The state discharge standard for arsenic-containing wastewater which is the first kind of pollution is less than 0.5 mg/L. In fact, in a certain company, the acidic arsenic-containing wastewater in non-ferrous smelting was as high as 860 mg/L, which is far beyond the state discharge standard. Obviously, the direct release of this wastewater without further treatment would result in great hazards to the ecological environment. To aim directly at the characteristics of acidic arsenic-containing wastewater, in this study, two steps of treatment including oxidation-flocculation and removal fluoride by mixing alkaline neutralization were suggested. Through analyzing various influencing factors in treatment effects, the optimum technical conditions were obtained. The sediments after treating were recyclable and the secondary pollutions can be avoided. Moreover, the results also show that, all indexes of the effluent after treating are lower than the First Grade Standard of Integrated Wastewater Discharge (GB 8978-1996). This novel method has advantages of short flow sheet, easy operation and low cost.

Jan 1, 2014

By S. K. Pan

The process flow-sheet adopted in treating hematite iron ore in India through wet circuit generates not only 15-25% slime of Run-of-Mine (ROM), but also results in loss of very high quality fine iron ore particles along with it. As the reserves of hematite iron ore is depleting, it is necessary to explore the possibility of upgrading other types of low grade iron ore and slime for recovery of iron minerals; extensive research in this field is being carried out. While beneficiation of low grade ore is yet to be established, slime beneficiation has been quite successful and many installations of slime treatment plant are underway. In SAIL mines, the slime is mainly the discarded particles from Classifiers, which are less than 0.2 mm sizes. R& D initiative has been focussed on the beneficiation of the slimes (49-60% Fe, 3-10% Al2O3 & 4-10% SiO2) of Dalli mines to generate concentrates assaying 62-64% Fe, 2-3% Al2O3, 3-4% SiO2 and a few innovative facilities for the same has been introduced at this mines of Bhilai Steel Plant (BSP). At Dalli mines, the slime is of very poor quality. A typical slime analysis assays 48.54% Fe, 15.1% SiO2, 8.5% Al2O3 and consists nearly 60% (by wt.) particles less than 38 micron. Slime analysis revealed substantial quantity of very high density mineral particles, those causes jamming of Thickener due to faster settling. A novel technique has been implemented to classify the concentrate ore particles from the gangue mineral particles by processing through Fluidized Bed Classifier (FBC) system, which is a gravity concentrator, to treat 50% of the slime generated and the rest is treated through de-sliming hydro-cyclone followed by Medium Intensity Magnetic Separator (MIMS). A special self-vibrating launder has been designed and introduced into the system to recover tiny iron ore particles, which could not get captured by the permanent Neodymium rare earth magnet in MIMS. The classified iron mineral particles from FBC are further treated in a battery of hydro-cyclones followed by modified Slow Speed Spiral Classifier (SSSC) unit. Multiple feed entry system to the SSSC unit is unique and use of particular feed entry point depends on the desired quality of the product and thus converted to a beneficiation equipment rather than mere de-watering unit. By processing slime in FBC system, the valuable iron ore particles with 62.5% Fe, 5.2% SiO2, 2.23% Al2O3 has been recovered from the slime at a material yield of 30%. And very high valued concentrate particles with more than 65% Fe has been sorted out through the magnetic separation route. The overall extra production of beneficiated slime concentrate is 40-45 tph with 63-64% Fe from a slime feed of 120-130 tph solid. This paper outlines few new approaches in iron ore slime beneficiation at Dalli mines for maximum recovery of valuable minerals. Keywords: fluidized bed classifier (fbc), iron ore slime of dalli mines, medium intensity magnetic separator, slow speed spiral classifier (sssc)

Sep 1, 2012

By H. M. Yang

Structural alteration of pyrophyllite during mechanical activation in a planetary mill was investigated by X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR) techniques. Mechanochemical effect markedly promotes the decrease in reflection intensities with increasing the grinding time. Prolonged grinding causes the pyrophyllite to become the amorphous structure. It can be indicated that pyrophyllite is very susceptible to alteration by grinding. Crystal size (d006) of pyrophyllite appears to be a limit after 2h grinding. IR spectroscopy analysis shows a little alteration in the bands of pyrophyllite after mechanical activation. The results indicate that the ordered structure of pyrophyllite is destroyed and lattice deformation occurs. Porous silica was then successfully prepared via leaching the mechanically activated pyrophyllite. Pyrophyllite was first ground for 6 h. Ground samples were subsequently leached with 4 M hy-drochloric acid at 80 °C for 2 h to produce porous silica with specific surface area of 188.1 m2/g, total pore volume of 0.18 mL/g and average pore size of 3.9 nm from N2 adsorption analysis. Otherwise, the porous silica obtained from direct leaching of the original pyrophyllite only has a specific surface area of 4.3 m adsorption analysis. 2/g and total pore volume of 0.03 mL/g. It is inferred that grinding is favorable for the formation of microstructure pores. It offers a simple and convenient route for the preparation of porous materials from natural minerals.

Jan 1, 2014

By N. S. Phala

Declining gold grades, mineralogical complexity of ore bodies, increasing input costs, more stringent conditions in the licenses to operate, and uncertain gold price dynamics combine to exert significant ongoing pressure on margins of gold producers. Innovative approaches of extracting the metal from its ores are required to realize value from existing and future assets. In a conventional gold processing plant, size reduction of mined ore to produce floatable or leachable product is a significant cost contributor. A step change in cost reduction will be attained if radically energy efficient grinding approaches can be developed, replacing tumbling mills. In the path towards that goal, some quick wins are possible through waste rejection before grinding, and pre-treatment of mill feed to reduce grinding energy demands. Gold locked in complex mineralizations puts pressure on margins by increasing cost per oz (typically high $/t and low metal recoveries) in the hydrometallurgical steps. Gold miners are primarily price takers. The current narrow range of gold uses (predominantly investment and jewellery) is not an entirely desirable state. Some diversification into commercial uses would potentially be a price stabilizer. In this paper, promising research directions, some not always fully explored in the gold metallurgy research space, are highlighted to stimulate radical innovation for substantial value enhancements. The author strongly believes a shift from a traditionally conservative and incremental innovation approach to a more aggressive one, across all aspects of the gold metallurgy value stream (processes to products), is what the industry needs. Keywords: gold metallurgy value stream, thiobaccilus ferroxidants, HPGR

Sep 1, 2012

By G. W. Zhang

Ultra-fine Stirred Mill is a kind of high energy efficient equipment for ultra-fine grinding, and has been the mainstream equipment in the submicron powder and slurry industry. This paper mainly describes flow-field numerical simulation of the three popular ultra-fine grinding mills: (respective-ly as) Disc Stirred Mill, Pin Stirred Mill and Spiral Stirred Mill, by means of the software Computational Fluid Dynamics (CFD). In the flow-field numerical simulation, the velocity gradient, shear rate dispersion of the flow-field, the viscosity dissipation rate were analyzed with CFD. It is discovered that Pin Stirred Mill has the highest velocity gradient in circular directions and the most homogeneous distribution of shear rate among the three. Flow-field numerical simulation provides a new way (and means to) for the parameter optimization design and project enlargement of Ultra-fine Stirred Mill. The experiments were also carried out, the results are consistent with the results of the simulation analysis. For example, in GCC grinding experiments under the same conditions, the specific energy consumption of Pin Stirred Mill with 3600L in volume is 15%~17% less, and its processing capability is 13%~15% better than Disc Stirred Mill. Now with its optimized structure and excellent performances, more than ten sets Pin Stirred Mill with 3600L in volume have been used in industrial production in Shandong, Guangdong and Hunan province.

Jan 1, 2014