Search Documents

By N. ??dyanik, Z. Kugukaldinova, O. Mishurina, Y. Glazkova, E. Mullina

"This paper describes the process flow of a selective processing method for acidic mine waters formed in the copper sulfide industry and characterized by a high content of copper, iron, and manganese ions. The proposed method comprises a series of sequential processes: the 1st stage is the recovery of Cu2+ ions by precipitation, the 2nd stage is the recovery of Fe2+ and Fe3+ ions as a dispersed phase by acid-base precipitation, followed by recovery in the 3rd stage of Mn2+ ions by converting Mn2+ with an oxidizing agent into insoluble forms of manganese and subsequent recovery of the dispersed phase by electroflotation. The developed method was tested on the acidic tailing storage facility (TSF) water of a mining project in the Urals region. The practical results of the implementation of the developed method have shown that its implementation will allow to recover copper, iron, and manganese in the form of salable products with a simultaneous decrease in their concentrations in adjacent water bodies down to the applicable MPCs. The process is a simple one, does not require any sophisticated expensive equipment and can be implemented either as a standalone solution or as part of existing treatment facilities. INTRODUCTION As a result of unsustainable utilization of natural resources in Russia, only a small fraction is processed into commodity products, while the rest is systematically dumped as emissions, effluents, and other wastes, polluting the environment. By amount of waste and concentration of valuable components, those wastes can be classified as aqueous technogenic resources [1, 2]. Therefore, the development of processing methods for this mineral resource category is an urgent and priority task that will significantly improve the industry’s profitability and the environmental conditions in the respective regions. MATERIALS AND METHODS Following research methods were mainly applied in this study: lab-scale and pilot-scale tests in a diaphragmless two-chamber electric flotation cell; for solutions and recoverable process products — chemical analysis using photometric determination techniques for metal cations and atomic adsorption determination techniques for the processing products. The phase composition of the precipitates formed in the process was investigated by X-ray phase analysis in the general-purpose diffractometer with a copper anode DRON-1."

Jan 1, 2018

By A. N. Lazaridi, S. I. Afanasenko, S. A. Safonov

"This scientific work presents the results of comparative tests of centrifugal concentrators with a vertical and horizontal axis of rotor spinning. The article also describes a qualitative analysis of the behavior of mineral particles in a centrifugal field with fluidization for concentrators with a horizontal axis. The analysis was aimed at studying the effect of the quantity of fluidization holes in the basket on the degree of magnetite recovery and the effect of the basket rotation speed. The experiment demonstrated that concentrators with a horizontal axis are not inferior in terms of the qualitative recovery indicators to concentrators with a vertical axis. The researches also provided facts about the wide practical application of concentrators with a horizontal rotor arrangement. INTRODUCTION Methods of gravity concentration, attractive for their ecological purity, see their revival. First of all, this is due to the invention of centrifugal concentrators with the fluidization of the layer of mineral particles. The creation of a new generation of gravitational centrifugal concentrators made it possible to achieve a tangible breakthrough toward the direction of reducing the grain size of mineral particles effectively divided by density, up to 10 µm at a high production capacity of the vessels reaching 500-600 tons per hour. Such separators enable dressing a crushed ore of flotation grade and in some cases replace the flotation process, especially in primary operations, in joint cycles. In the long term, this method of concentration should significantly expand the scope of application, replace partial flotation processing, ensure the introduction of environmentally friendly energy-saving technologies at ore-processing plants. Summarizing the international experience for the last 30 years, it can be confidently asserted that centrifugal methods of concentration have become widely used in processing schemes for the separation of finely dispersed products in the mining industry. An interest in the creation of installations using centrifugal acceleration for the separation of mineral particles by density has particularly grown. Dozens of centrifugal concentrator designs have been created and continue to be improved. Centrifugal concentrators have a number of obvious advantages, which are especially relevant today. Losses of fine gold during the process of mining are well known. Gold washers screw, spiral separators, jigging machines and sluices traditionally used in the production processes do not solve the problem of fine gold recovery. Table 1 shows the results of comparative tests of a centrifugal concentrator (ITOMAK) and other concentration equipment. According to the research conducted by the company GMRS, Krugersdorp, South Africa (2000), the initial material was gold ore crushed to 150 micrometers (90%)."

Jan 1, 2018

By Irena Grigorova

"Vermiculite is a naturally occurring mineral compound composed of shiny flakes, resembling mica. Worldwide, vermiculite has been used in various industries since 1920. When heated to a high temperature, flakes of vermiculite expand several times their original size. The expanded vermiculite is a lightweight, fire-resistant, absorbent, and odorless material. These properties allow vermiculite to be used to make numerous products, as an additive, for example to potting soil, in agricultural, construction, horticultural and industrial applications, including pesticides, insulation, potting mixes, brake pads, sound deadening materials, fire protection, paints, sealants, insulating concrete and etc. Over recent years researchers have been looking for effective economic and environmental methods and solutions for fine technological waste utilization. As a result of vermiculite ore processing large quantities of fine waste dust are formed. Until now there has been no application for this waste product. Currently this waste product is stockpiled using valuable land space, and is a potential contaminant. The paper presents the results of a study on the possibility to obtain briquettes from fine vermiculite by-product. The particle size distributions, chemical and mineralogical compositions of vermiculite were determined. It was established that consolidation of vermiculite dust by methods of briquetting and its consequent application in agriculture as meliorants for physico-chemical treatment, improves soils aeration structure and properties."

Jan 1, 2014

By N. Panteleeva, E. Konoplev, I. Michailova, S. Titkov, S. Aliferova, T. Gurkova, T. Chumakova

Cationic flotation using alkylamines and their derivatives as collectors, and characterized by high selectivity of mineral particle separation, is finding ever growing industrial application. In recent years the industrial application has been initiated of new cationic collectors - alkylmorpholines. Efficiency of cationic surfactants operation as collectors is dependent upon their colloid and sorption properties and the availability of silicate .carbonate rock-forming mineral impurities in the ore, which sorb the cationic collector. Investigations have been carried out on the influence of frothers and organic depressors with various compositions upon physical-chemical and flotation properties of alkylamines and alkylmorpholines. On the basis of these investigations requirements for organic depressor were developed and new flotation reagents were proposed (V-1 frother and KS-MF depressor). The use of new reagents enables one to decrease considerably the consumption of expensive cationic collectors and to enhance the floatability of coarse mineral particles. Data of new reagents industrial application is presented. The reagents developed can be used for flotation processing of other ores.

Jan 1, 2003

By G. M. Wolfaardt, B. C. Qi

"From a lifecycle point of view, biologically digested sludge is a valuable product that should be reused if possible. Sludge may be applied to agricultural land for further sludge treatment and improvement of the characteristics of the soil. The characteristics of sludge that affect its applicability for soil conditioning include moisture content, pathogens, nutrients and metals. In this paper, the use of solid anaerobic digestion sludge of the lignocellulosic residues to condition soil was investigated in regards to nutrient composition, water content/retention capacity, hygienic quality (contamination of pathogenic bacteria) and heavy metal adsorbing/releasing characteristics of the sludge.It was found that the digested sludge had approximately 44.5% free and immobilized water and 46.9% bound water. The water-holding capacity of the sludge was high. This was a merit to apply the sludge to agriculture in dry areas. Anaerobic digestion under thermophilic conditions showed a promising disinfecting effect to the sludge, in contrast to the landfill digestion. The anaerobic digestion sludge could be considered as a humus-rich hygienic product that improves soil fertility and water holding capacity, nourishes plants and immobilizes heavy metals in the environment"

Jan 1, 2003

By Bruno Michaux, Markus Reuter, Martin Rudolph

"It is relatively well-established in the literature that the flotation of calcium minerals using fatty acids as collector is very sensitive to the process water composition. In particular, hard waters have often been reported to strongly reduce the target mineral recoveries due to the formation of insoluble compounds such as calcium and / or magnesium dioleate, thus reducing the amount of collector available for adsorption onto the mineral surface. In this study, the flotation of a fluorite pre-concentrate was performed with tall oil, an industrial collector essentially containing fatty acids. The tests were performed in a variety of synthetic waters to simulate multiple degrees of water hardness, and to differentiate the role of magnesium and calcium ions on the flotation performance. The flotation tests revealed that, under the studied conditions, a significant difference between flotation in calcium-rich and magnesium-rich waters was observed, suggesting strong ion-specific effects in the system. Specifically, calcium-rich waters slightly improved the fluorite recovery, whereas magnesium-rich waters caused a decrease in recovery by as much as 20%. This paper is focused on the flotation kinetics aspect of the system. This approach highlighted the interesting finding that calcium ions did not simply increase the fluorite recovery, but also significantly increased its flotation kinetics. The magnesium ions, on the other hand, had the exact opposite effect.INTRODUCTIONAs the mining industry is facing an increasing number of issues related to its fresh water consumption, the idea of using alternative water sources for mineral beneficiation is gaining significant momentum. As a result, a proper understanding of the role of water chemistry in flotation is becoming more and more urgent, leading to an increasing number of studies on this topic."

Jan 1, 2018

By Mojtaba Ghorbannezhad, Abbas Sam, Soroush Arabzadeh

One of the dewatering methods in mineral processing plant is filtration system. Disk filters are included the porous surface with pressure drop on both sides, Water in the pulp passes through the surface and solid particles remain as a cake on it. Wet concentrate production of magnetite processing plant at Golgohar Mining and Industrial Company with solid tonnage of 160 ton per hour and 49% solid amount contains 166 m3/h of water. In the present study, in addition to studying disc filter performance, the effective parameters on cake moisture were studied using Vacuum Bottom-Feed Leaf method (in the laboratory scale). Optimization was performed using the Taguchi method. The results showed that the cake moisture is reduced by increasing particle size and solid percentage (because of specific resistivity reduction), while the rate of cake formation and its thickness are increased. Also, it was found that by increasing pressure, the cake moisture is reduced and cake formation rate and its thickness are increased. In this study, the effect of fabric texture was also examined. Lowest cake moisture was obtained in condition of using compressed plain fabric with mono-multi filament fibres, pressure at 75kPa, solid percentage of 65 to 70, particle size (D80) equivalent to 123µm and disk rotation speed of 1.25 rpm.

Jan 1, 2014

By V. Tsyplakov

This article reviews factors of preg-robbing effect, occurring in the course of pressure oxidation of ore and concentrates, containing chloride compounds and so-called 'organic carbon'. The article also summarizes the main results of the studies and testwork conducted to overcome this effect. The following efficient preg-robbing mitigation methods have been noted: higher temperature of pressure oxidation process, preliminary removal of natural carbonaceous material from concentrate, chloride removal prior to concentrate pressure oxidation, and addition of water-soluble organic blanking agents, which suppress the adsorption activity of the native ore adsorbents. Keywords: preg-robbing, double-refractory gold concentrates, pyrite, arsenopyrite, blanking agents, pressure oxidation, autoclave leaching

Sep 1, 2012

By Mohan Ram

Structural impurities in the crystal lattice of rock phosphate of Indian origin is a great challenge for beneficiation and practically possesses remote scope of upgradation to the desired level for industrial utilization. There is a wide occurrence of rock phosphate in different parts of India with different characteristics viz. siliceous, carbonaceous and ferruginous. The structural cationic replacement in the composition of apatite is due to the exchangeable cations present in the external impurities associated with the rock phosphate ore. The Indian rock phosphate ore from Purulia district, West Bengal is characterized as unusual structural composition due to the exchangeable cation in its composition. The elemental distribution of ore exhibits the disproportionate ratio of P2O5 and CaO which is 5.88: 3.31 in reference to the theoretical composition of P2O5: CaO in apatite which is 4.23: 5.55. The substitution by trivalent Al+++ cations within the structure of apatite in place of divalent Ca++ is found upto 18% and substitution of exchangeable cation in place of PO4 and F ion by CO3/SO4 is found upto 0.1% and OH ions upto 0.2% respectively in a lattice of apatite thereby diluting the grade of rock phosphate and restricting its industrial use even after beneficiation. This paper reveals the unusual compositional features of rock phosphate under study and is a guideline to the mineral industries using such rock phosphate. Keywords: external impurities, exchangeable cation substitution, structural compositional features, electron probe micro analyzer

Sep 1, 2012

By André Mans, Frans B. Waanders

Current losses of Ferrosilicon (Fe-Si), which is used in the dense medium separation (DMS) of iron ore at Kumba Resources, Sishen, South Africa occur due to adhesion to the separation products and also by being present in the effluent stream, due to abrasion. The losses contribute greatly to the running cost of the plant and the purpose of this project was to determine the characteristics of the unused Fe-Si and then to characterise the changes that occur during storage and the use thereof. A Scanning Electron Microscope (SEM) and Mössbauer Spectroscopy (MS) were used to investigate the characteristics of the fresh and used Fe-Si. It was found that the biggest loss of Fe-Si was due to the abrasion of the particles during the DMS process, which resulted in the liberation of Fe and subsequent formation of an oxihydroxide froth. A possible change in magnetic properties was also observed, leading to further losses that could occur during prolonged use of the medium. No clear changes to the Fe-Si occurred during correct storage methods, as was initially thought.

Jan 1, 2003

By Gaurav Soni, Roe-Hoan Yoon

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model predictions have been compared with the results of a series of laboratory flotation tests conducted using mono-sized glass beads of different particle sizes and contact angles under different operating conditions. Some of the experiments were conducted using a 1:9 mixtures if hydrophobic silica and hydrophilic magnetite, so that the product graded could be readily determined by simple magnetic separation. The model predictions are in good agreement with the experimental results both in recovery and grade. A computer simulator developed on the basis of the model is capable of designing a preliminary flotation circuit on the basis of feed characteristics, e.g., size-by-liberation data, and the hydrodynamic information on the flotation cells to be incorporated in the circuit.

Jan 1, 2014

By G. Venkateswara Rao

The jigging of ferrous ore to produce higher-grade products has been practiced for many decades. This is due to easy separation, a beneficial trade- off between operating cost and reduced yield relative to Dense Media Separation (DMS). Jigging becomes prominent for beneficiation of iron ores in the coarser size range. At present drive is towards the use of under bed air pulsed jigs for the beneficiation of ferrous ores. The main advantage is that the under bed air pulsed jigs are capable of generating the large pulse of amplitudes required to fluidize a deep bed of heavy ores particularly lump iron ore up to 40mm size. The major jig parameters effecting the jigging operation are bed height, shape of the pulse, residence time, operating pressure, valve cycle time and water flow rate. With the pulse shape set correctly for optimum stratification rate, even it is still necessary to provide enough residence time, to ensure the difficult material will take time to migrate to the expected layer in the bed. In order to find the Jig Stratification Index (JIS) parameters like bed height, operating pressure, water flow rate, cycle valve time and shape of the pulse were optimized first by conducting various tests. Typical Iron ore samples from Odisha (both lump and fines) were subjected to stratification studies at residence time of 1, 5 and 15 minutes. Jig Stratification Index (JSI) for both lump (0.30) and fines (0.20) were determined by using APIC Jig. The maximum possible JSI was calculated by using heavy liquid separation test (0.42 for lump and 0.24 for fines). It is found that the jig bed JSI is less than the Heavy liquid JSI for both lump and fines. The ratio of Jig bed JSI to the heavy liquid JSI is 0.83 for lump and 0.71 for fines. The JSI and ratio of Jig bed JSI to Heavy liquid JSI are low for fines due to fluid turbulences causing some degree of remixing in the jig bed. The fluid turbulences are more for fines than lump, hence jigging of fines is difficult and challenging. Keywords: sub grade iron ore, gravity separation, jigging, apic jig, stratification, residence time, jig stratification index

Sep 1, 2012

By Weiran Zuo, Emmy Manlapig, Fengnian Shi

The effect of metalliferous grains on electrical comminution efficiency was investigated by comparative experiments using natural rocks and synthetic samples. The result indicated that the existence of metalliferous grains affects the breakage probability and product size distribution of electrical comminution. On average, metalliferous grains increased the breakage probability of particle in the first pulse discharge by 55% and generated finer product at the coarse end. As a result, particles with metalliferous grains exhibited higher energy efficiency than that without metalliferous grain in electrical comminution. A positive linear relation between product fineness and specific energy in electrical comminution was observed. With the assistance of numerical simulation on the electrical field distribution of ore particle, the role of metalliferous grains in electrical comminution is confirmed and the mechanism of metalliferous grains effect is elucidated. Understanding of the effect of metalliferous grains on electrical comminution is important to evaluate the feasibility of applying electrical comminution to ores with different mineral composition, and to understand the breakage behavior in electrical comminution.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, L. Hosseini, M. Zare

Difference between plant feed specifications in practice and design feed is a problem that most of processing plants face during operating and commissioning. This topic has led to inappropriate operating and necessitates repeating the basic tests on new feed. Gol-E-Gohar fourth concentrate line with a capacity of 2 MTPY, located in Kerman province, is the first iron concentrate plant in Iran in which High Pressure Grinding Roll (HPGR) technology has been applied. Plant&apos;s feed consists of 30% AG mills pebbles of lines 1-3 and 70% run of mine crushed ore whose Fe=51%, Fe/FeO=2.5, S=1.7% and work index=15 kWh/t. Desired concentrate has Fe>68% and S<0.7%. After the plant construction and operation commencement, providing design feed was not possible due to the crushing unit`s not being complete, therefore the plant was fed by AG mills pebbles. For predicting optimal conditions of the plant and investigating the possibility of improving the current concentrate specifications, sampling from the new feed and laboratory and pilot tests was performed again. Studies showed that new feed has Fe=41%, Fe/FeO=3.5, work index=17 kWh/t. Results of laboratory tests with Davis tube device and pilot tests run using magnetic separators with simulating the plant`s circuit showed that with current feed, achievable recovery in industrial scale would be 75.52% which compared to plant&apos;s recovery in studied period (75.94%) shows that plant operated in optimal conditions. To improve the current concentrate specifications (Fe=66%, S=1.03%, Ferec=75.94%) and for achieving desired concentrate, samples were reground to four fractions with k100= 300, 212, 100, 45 and Davis tube tests were performed on each of the samples separately. Results showed that the fraction whose k100=212 µm or k80=200 µm has respective Fe and S grades of 68.27% and 0.681% which are consistent with the desired concentrate.

Jan 1, 2014

By S. M. Viduka

This paper presents a numerical investigation of solid separation in jigging device, which is a gravity separation method widely used in ore processing. Separation is recognized as being heavily dependent on fluid motion in the jig. This study explores the effects of the inlet time dependent velocity profile on jigging performance. Modelling of the liquid-solid system is performed through a combination of computational fluid dynamics (CFD) to simulate liquid flow and discrete element method (DEM) to resolve particle motion. The initial packing conditions consist of a binary-density particle system of 1130 particles each 1 cm in diameter. A variety of jigging profiles are implemented in jigging. The saw tooth pulsation profile is selected with three variations in both amplitude and frequency. The performance of each profile variant is compared in terms of solid flow patterns, separation kinetics, energy, and mean particle position. These quantitative comparisons demonstrate significant differences in the segregation rate, energy, and solid phenomena, helping find an alternative optimum operating setting for the system.

Sep 1, 2012

By A. Kogelbauer, A. Stadtschnitzer, A. Boehm, F. Schillab

"The paper covers the design and implementation of an industrial dense medium cyclone plant for carbonaceous iron ore, the proving of efficiency as well as the development of a predictive model for plant control. The VA Erzberg GmbH mines about 12 Mio.t of carbonaceous rock ore at the “Steirische Erzberg”. Due to increased demand of the Austrian steel plants, the production of ore concentrate was raised by 30 % up to 3.0 Mio t/a during the last 5 years. One of the projects to realize the increase in capacity at improved concentrate quality was the implementation of a dense medium cyclone plant for the fine size fraction – 8 +1 mm replacing the former dry permanent magnetic drum separators. By physical separation the siderite variety “spateisenstein” (42% Fe) of a density of 3,8 g/cm³ is separated from ankerite (10 – 17% Fe), the second iron bearing carbonate with a density of 3,2 g/cm³, dolomite, calcite and silicate bearing schists. The feasibility of the process was proven by the test results obtained from a test rig, that was constructed and operated in close cooperation between the Chair of Mineral Processing, Montanuniversitaet Leoben and VA Erzberg GmbH. The density separation surpassed the efficiency of magnetic separation clearly shown by •- values. The plant performance tests (capacity 120 t/h) verify the cut densities defined by Tromp T50 -values and the assigned efficiency found in the pilot tests at varied settings of media density, pressure drop, cone angle and apex diameter. The test rig as well as the final process will be presented. In order to create a tool to predict the performance of the DMS in the centrifugal field at various settings for varying feed composition the experimental results from size and density testing are analyzed in a modified way to obtain physically justified, smooth approximations for the performance curves. Models developed on coal washing plants are checked for their validity at increased densities."

Jan 1, 2018

By Alban Lynch, Benigno Aquino, Hakan Dündar, Alexander Kalugin, Marco Delgado, Alberto Palomino, Ali Türkistanli

Dynamic separators are efficient dry classifiers because new designs during the last 50 years have reduced the by-pass and improved the partition curve. By contrast cyclones have been used as classifiers in wet grinding circuits for 50 years but without serious change and the early problems which were caused by high and variable by-pass, and different mineral specific gravities, still exist. High frequency screens are now used for wet separation and the operating characteristics of closed grinding circuits using cyclones or screens are discussed. Data come from circuits at the Condestable, Cerro Lindo, El Brocal and Catalina Huanca mines in Peru, the Eczacibasi mine in Turkey, and the Apatit mine in central Kola Peninsula in Russia. All classifier data are described by their partition curves and all mill data by their breakage rates. With cyclones the by-pass, d50, and sharpness of the partition curve change as operating conditions change but with high frequency screens the values vary little because the by-pass is low, the sharpness is high, and d50 depends on the aperture size. Data from all plants indicate that lower by-pass and sharper separation improve breakage rates and throughputs. An initial model of the screen is proposed.

Jan 1, 2014

By Lei Pan, Roe-Hoan Yoon

"Direct force measurement for bubble-particle interaction has been difficult due to bubble deformation, which makes it difficult to know the separation distances between the two macroscopic surfaces. In the present work, we have developed a method of monitoring the deformation accurately, while directly measuring the interaction forces. In effect, we can ‘see’ bubbles interacting with mineral surfaces under different hydrodynamic and chemical conditions and determine both the hydrodynamic and surface forces involved. In the present work, a high-speed camera has been used to record the optical interference fringes of a thin liquid film (TLF) of water formed on a mineral surface. The recorded fringes are then used to reconstruct the spatiotemporal profiles, from which one can determine the hydrodynamic pressure using the Reynolds lubrications theory. From the forces directly measured in the present work and the hydrodynamic pressures obtained from the fringes, we have determined the disjoining pressure. The results show that air bubbles interacting with hydrophilic surfaces form stable TLFs with zero contact angles. The TLF formed on a hydrophobic surface thins fast, form a ‘pimpled’ film, and ruptures to form a finite contact angle. The new information obtained in the present work may be useful to better understand the role of hydrodynamic and surface forces affecting bubble-particle interactions."

Jan 1, 2014

By Partha Patra

Numerous proteins of varying properties are available in extracellular bacterial proteins (EBP) isolated from Paenibacillus polymyxa. EBP was fractionated through ammonium sulfate precipitation in a controlled fashion and characterized through SDS-PAGE technique. Different groups of proteins, (Group A~D) exhibited varying degrees of surface affinity to minerals such as quartz, pyrite, chalcopyrite, galena and sphalerite. Interaction with mineral specific bioproteins rendered pyrite and chalcopyrite hydrophilic while surface of quartz, galena and sphalerite turned more hydro-phobic. Specific groups of proteins could thus be used for selective separation of galena, sphalerite and quartz from pyrite and chalcopyrite (as a mixed sulfide) through microbially-induced flotation or selective flocculation.

Jan 1, 2014

By Junji Shibata

In a present process to treat the tungsten carbide tool waste, the wastes are roasted in air and then an alkali leaching is carried out in an autoclave. An environmentally friendly process is required to recover rare metals (Co and W) from the wastes. The effect of mechano-chemical (MC) treatment on leaching of rare metals was investigated in this study. The solvent extraction and crystallization-stripping methods were applied to separate and recover tungsten and cobalt in the leached solutions. The MC treatment for the rare metal leaching is effective to dissolve rare metals from the wastes due to the change in crystalline structure of WC and oxidation of WC with KMnO4. Cobalt ions are extracted with D2EHPA by a cation exchange reaction. Tungsten in the leachate can be extracted by TOA (tri-octyl amine) as an extractant, because tungsten species exist as a form of anionic species in acidic solution. The rare metals in organic phase are recovered as insoluble salts such as oxalates and ammonium salts in the crystallization-stripping process. Keywords:unheated oxidation, solvent extraction, crystallization-stripping, recycling

Sep 1, 2012