Search Documents

By H. Wotruba, L. Gronen, A. Hellmann, S. Sindern, J. Katzmarzyk

"This paper focuses on the beneficiation of the REE-Y-Nb-Zr complex ore from the ‘Khalzan Buregtei’ deposit, Mongolia. Pre-concentration based on mineralogical studies was investigated at the Unit of Mineral Processing (AMR) and the Institute of Applied Mineralogy and Economic Geology of RWTH Aachen University. In order to minimize the energy consumption in the most energy intensive grinding process a pre-concentration process using dry magnetic separation of particle sizes coarser than required for the liberation of the valuable ore minerals was designed. Dry magnetic separation in the particle size range of 63-250 µm is suitable as the pre-concentration method, due to the intergrowth of REE-Y-Nb-Zr bearing minerals with magnetic minerals determined by QEMSCAN© analysis. The results showed that a mass reduction of 45.3 wt.-% at high recoveries of REE, Y, Nb and Zr (90 wt.-% and higher) in the pre-concentration product was achieved at the beginning of the process chain. The improvement of process efficiency as shown in this study depends on the abundance and association of minerals affecting the magnetic properties (e.g. hematite) of the ores. Therefore, these mineralogical parameters are as important as grain size and ore grade for the geometallurgical evaluation of potential mining operations at ‘Khalzan Buregtei’.INTRODUCTION Polymetallic deposits containing other critical elements besides REE have the advantage of being robust to economic development and fluctuations of individual metal prices. (Gronen et al., 2016). These deposits can host economic grades of heavy and light REE, Y, Nb, Ta, Zr in complex mineralogical compositions. About 120 deposits of this type are known worldwide, including ‘Norra Kärr’ in Sweden, ‘Strange Lake’ in Canada and ‘Khalzan Buregtei’ in Mongolia which are not valued economically yet. (Salvi. & Williams-Jones, 2004.)"

Jan 1, 2018

By B. Rezai

Impeller speed and air flow rate are two influence parameters on coarse particles flotation and collision and attachment angles. So, in this research recovery of quartz particles at four diameter classes carried out and collision and attachment angles investigated. It is found that maximum flotation response was observed at Impeller speed of 1100 rpm and 15 L/h air flow rate. For either more quiescent (Impeller speed<1100 rpm) or more turbulent conditions, flotation recovery decreased steadily. Furthermore, amount of attachment probabilities is calculated using suitable equation. According to this study, with decreasing particle size, air flow rate and impeller speed, probability of attachment increased and with increasing contact angle, probability of attachment increased. For various air flow rates, impeller speed and particle size, collision angle has been calculated. Maximum collision angle obtained at with 15 L/h air flow rate, particle size of 256 µm and impeller speed of 700 rpm and minimum collision angle obtained at with 45 L/h air flow rate, particle size of 545µm and impeller speed of 1300 rpm. In this study, maximum attachment angle, , was around 75 L/h air flow rate, particle size of 256 µm, contact angle of and impeller speed of 1300 rpm and minimum attachment angle was with 15 L/h air flow rate, particle size of 545 µm, contact angle of and impeller speed of 1300 rpm. ?82.72 ?64 cr??33.39 ?90 ?13.0 ?60

Jan 1, 2014

By Jing Zhou

In view of the state of the long time use of sodium cyanide in lead-zinc-sulfur-silver multimetallic ore production, we propose alternative reagents system through experimental research. The experiment first used TJ, sodium sulfide to adjust the flotation pulp, after that, zinc sulfate, sodium sulfite was added to low alkaline pulp to inhibiting zinc sulfur mineral and adapted MB, 25# aerofloat and diethyl dithiocarbamate combination collectors to float lead minerals. The obtained test index is as follows: lead concentrate recovery rate of small scale test was increased by 5 to 10%, the recovery rates of gold and silver in lead concentrate were increased by 7% and 11% respectively; the industrial test is conducted under the condition that the total grade of lead and zinc content in raw ore decreased by 4.81%, the total recovery rate of lead and zinc increased by 7%, recovery rates of gold and silver in lead concentrate were increased by 7.62% and 9.65% respectively. So it successfully realizes the target to replace the sodium cyanide, using low-alkaline non-toxic reagents system in mineral processing practice of three kinds of complex lead-zinc-sulfur ore of this mine. Keywords: refractory lead-zinc-sulfur ore, depressant, non-cyanide flotation

Sep 1, 2012

By B. Orberger, J. M. Milazzo, S. B. Blancher, J. Lützenkirchen, J. L. Dubos

"Industrial dusts are commonly agglomerated using empirical recipes with binders such as bentonite, while Sludges are agglomerated into mixes. Those materials contaminate the products, are expensive and generate significant amounts of slag. Achieving cold dust agglomeration with little or no binder requires understanding the controlling parameters in order to predict and optimize the process behavior. This in turn necessitates comprehensive dust characterization to base predictions on measurable characteristics. In the present work we collected 13 Mn-rich dusts over all the process chain: feed fines, smelting, and refining dusts, as well as ferromanganese alloy dust. This is the first systematic study of dusts along the Mn-processing chain for chemical, physical and mineralogical parameters. X-Ray Diffraction, Qemscan® and laser granulometry analyses show that the mineralogy, Particle Size Distribution (PSD) and morphology evolves from complex heterogenous to simple, homogenous along the process chain: The mineralogy of the primary ore dusts shows various hydroxides, oxides, carbonates, tectosilicates and phyllosilicates. The furnace dusts contain oxides, tectosilicates and carbonates with volatiles, while the refining dusts present only oxides and metal. Finally, the Metal dust is nearly pure metal. Particle morphologies and PSD vary from jagged, irregular particles with broad PSD (>1 mm to <0.3 µm) to smooth and spherical with narrow PSD (100 µm to <0.3 µm). The Metal dust is an exception with angular particles. The Cationic Exchange Capacities (CECs) of all samples range from 0 to 22 meq/100g. Specific surface areas (SSAs) range from <0.1 to 27m²/g, and seem to decrease with from ore feed to Metal dust. This may be due to the disappearance of hydrated and/or sheet-bearing minerals, since a smaller grain size usually implies an increased SSA. The zeta potential varies strongly over the range of the samples tested. However, beside the Gabon ore which has an Isoelectric Point (IEP) ~ 4.1, the other IEP ranges between 2 and 2.5."

Jan 1, 2018

By Ying Gu

Automated mineralogy methods and tools, such as the Mineral Liberation Analyzer (MLA) and the QEMSCAN, are now widely used for ore characterization, process design and optimization. Several case studies published recently demonstrate that large gains can be obtained through grinding and flotation optimization guided by automated mineralogy data. However, since automated mineralogy can only provide the information pointing to where the process gains can be made, it does not directly impact the production gain. Thus, a question is often asked: how to value the contribution of automated mineralogy to process improvement of a particular plant. This appears to be a difficult question. On close examination however, it is found that this is essentially a question of the value of information and it is reasonably well documented in various other industries. Hubbard (2010), in chapter 7 ?Measuring the Value of Information?, dealt with exactly this type of problem. The value of information is the reduced risk of an investment and opportunity loss. The methods Hubbard developed can be applied to estimate the value of automated mineralogy, as well as metallurgical test work, which also produces information that reduces the risk of investment. This paper first introduces Hubbard?s theory on the value of information and how to measure it. It then applies his methods to estimate the value of automated mineralogy, using Anglo Platinum?s fine grinding project as an example. In this case, the value of automated mineralogy includes the reduction in investment risk worth US$ 62.5million, in project rejection worth US$197 million and in opportunity loss worth US$320 million. In the end, a general model is developed to allow the simulation of the value of automated mineralogy in different mining operations constrained by different parameters.

Sep 1, 2012

By Arkady Senchenko, Yury Kulikov

"Basic theoretical grounds of the methods applied for crushing and grinding parameters determination according to international standards are given in this paper. Statistical data about crushability and grindability research are shown. The potential relationship between the values of Fred Bond Work indices and John Starkey indices (Crushing index, Ball mill index, Rod mill index and AG/SAG index) are discussed in this paper. In order to establish correlation between the crushability and grindability indices the analysis of over 2 500 tests for 165 deposits located in different parts of the world was performed. The relationships among different types of energy consumed for crushing and grinding were determined. A method for preliminary estimation of energy consumption in semiautogenous + ball mill grinding circuit is suggested for its application in preliminary technological solutions development and technical-and-economic assessment."

Jan 1, 2014

Over the last four years, a major collaboration between CSIRO-MIS, UCT and JKMRC has produced two significant advances in the modelling of comminution. The Universal Comminution Model (UCM) uses parametric SPH/DEM studies of comminution and separation devices to calibrate mathematical models which are suitable for industrial use. The Virtual Comminution Machine (VCM) uses the same computationally intensive techniques based on discrete element modelling (DEM) and smoothed particle hydrodynamics (SPH) to directly model any comminution device by combining a CAD file describing the machine design, sophisticated ore characterisation methods and advanced particle scale flow and breakage simulation. The UCM should be useful for process analysis and optimisation of existing equipment and circuits while the VCM should make a major contribution to the evaluation and development of new machines. Progress to date is encouraging with several processes now well described using DEM. This paper also reports on progress towards combining DEM for particles with a realistic slurry model based on SPH for different types of comminution devices. In due course, this combination should allow accurate modelling of particle transport in wet mills to be combined with DEM models.

Jan 1, 2014

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By Y. Y. Li, T. T. Yang, R. X. Zhou, Z. H. Shen

"Wetting theory is one of the basic theories of flotation. The effects of concentrations, carbon chain length and pH values of saturated fatty acid collectors (lauric acid, myristic acid, palmitic acid and stearic acid) on the surface wettability of collophanite and dolomite were investigated by measuring the contact angle with dynamic captive-bubble technique and calculating adhesion work of bubble-mineral. The results show that the contact angles both of collophanite and dolomite are higher with enhancement of hydrophobicity when pH value of 5~9. The contact angles both of collophanite and dolomite are reduced with improvement of surface hydrophilicity. When strong acid pH value of 2~4 or strong alkaline pH value of 10~13. The reasons for this are that the fatty acids mainly exist with insoluble RCOOH molecules in strong acid condition, and competitive adsorption of OH- and RCOO- in the mineral surface is formed in strong alkaline condition. With the increase of the collector concentration, the contact angles of the collophanite and the dolomite all first increase then decrease. The formation of hydrophilic micelles results in the decreasing of contact angles and enhancement of surface hydrophilicity opposite when the collector concentration exceeds CMC. The contact angles of the collophanite and dolomite and the WSG of the bubble adhesion increase, the hydrophobicity enhance with the increasing of carbon chains of saturated fatty acid from 12 to 18. The variation tendency for the adsorption quantity of collectors and floatability of collophanite and dolomite are in line with the change trend of contact angle basically. It shows that the wettability of solid-liquid-gas interface can be well characterized by the dynamic captive-bubble technique.INTRODUCTIONPhosphorite resources are the main raw material for producing phosphate fertilizer and producing phosphoric acid (Cao et al.,2005), which is an important strategic mineral resource. The useful minerals in calcareous-magnesium phosphate ore are collophanite, and the main gangue minerals are dolomite (SISH et al.,2003). The lattice ions of the phosphorite and dolomite are both Ca2+, their similar surface properties and similar floatability are the main reason for the flotation of calcareous-magnesium phosphate ore difficultly (Fang et al.,2011). Usually, fatty acid collectors are used for the flotation of calcareous-magnesium phosphate ore under acidic conditions by reversing flotation method to remove dolomite (ABOUZEID et al.,2009), or direct flotation is used to gather collophanite in the alkaline conditions (Gong et al.,2017). The flotation behavior of collophanite and dolomite affects the indexes of concentrate and flotation efficiency directly. Therefore, it is necessary to study the action mechanism and the flotation method of the collector with the phosphate rock and dolomite respectively (Moudgil et al.,1988; Hanna, et al.,1990)."

Jan 1, 2018

By L. X. Zeng

The low-grade nickel resource is very abundant in the western China. To make the best of the low grade nickel ore, we studied the process mineralogy and beneficiation process of nickel ore in the Yangliuping of Sichuan province. The grade of nickel is 0.45% in the nickel ore and the nickel exists in the sulfide including pyrrhotite, nickel pyrite, chalcopyrite primarily. The nickel distributes in pentlandite and magnetite over 90% and the copper does in the chalcopyrite over 95%. The carri-er minerals of useful elements tend to concentrate in space for concentration. As is shown in grain-size analysis of three major minerals, there are some more fine-grained grains with the percent of from 10% to 15% (<40 µm) and from 3.5% to 5.5% (<20 µm). So there will be some smaller size disseminated sulfide minerals difficulty to liberate in the process of concentration. The liberation degree of sulfide is not high and there are much associativity in the sulfides. Therefore, we should reclaim the sulfide aggregation dominating as pentlandite when concentrating. In addition, the sulphide minerals is so brittle that we should take care of preventing from crashing when grinding. The gangue mineral is mostly metamorphic mineral including serpentine, chlorite and amphibole which is easy to be argillization and difficult to concentrate.

Jan 1, 2014

By A. N. Zagorodnyaya

The results of research on recovery of ammonium perrhenate from by-products of lead production are presented in the article. For the first time in the world, rhenium marketable products were produced on lead plant of Kazakhstan. Distribution of rhenium in lead production has been studied. During oxidative agglomeration of lead charge, 67.43% rhenium is sublimated and at that, 67.27% rhenium is trapped by the dusts of a system of gas purification, out of them 6.21% is transferred into different solutions, 1.89% into slime and only 0.09% into exhaust. During agglomerate smelting, up to 72% of its rhenium is sublimated and condensed in the dusts also. At leaching stage of sulphate product under dusts processing by the method of sulphatization, 15% of its content in the dusts is transferred into solution. The sorption method on the ionite ?N-21 has been proposed for recovery of rhenium from the solutions of sulphatization. At the same time, rhenium recovery from the dusts into commodity was 13%. The method of direct hydrometallurgy - leaching the dusts by solutions of sulphuric acid under presence of manganous concentrates, has been proposed as alternative method of recovery. This method has allowed increasing recovery of rhenium and other metals from the dusts into solution up to 90%~95%. Rhenium solvent extraction by ??? has been proposed for recovery of rhenium from the leaching solutions. At that, extraction of rhenium into marketable product from the dusts is above 75%.

Jan 1, 2014

By W. Z. Yin

With increasing of mining depth, many iron ores in Liaoning Province contain carbonates such as siderite and ankerite. The emergence of these carbonates in ores creates a fatal impact on the running producing process of anionic reverse flotation in Dong Anshan Sintering Plant, which leads to ?concentrate and tailing no separated?. And its reason is still unknown. Moreover, siderite, despite that its ferric theoretic grade is only 48.2%, however, do not affect the blast furnace utilization factor, therefore, can be used as raw materials in ironmaking. In order to solve the separate problem of iron ore containing carbonates, five pure minerals, martite, magnetite, quartz, siderite and ankerite, were selected for a series single flotation experiment. The aim was to discover the flotation difference of these minerals, furthermore, to explore a new flow sheet for the iron ore containing carbonates. The results of single mineral flotation experiment reveal that the combination regulators, starch and CaCl2, in different pH extent, can make these minerals taking on obvious flotation difference, which make it possible to process the iron ore containing carbonates. A new flow sheet, step-flotation, to process iron ore containing carbonates is explored, that is, first step, direct-flotation processing, is to eliminate the bad effect that the carbonates bring in flotation system by collecting carbonates under neutral condition; the second step, reverse?flotation processing, is to get qualified iron concentrate by collecting quartz under alkaline condition. Manual mixed ore sample were processed successfully through this new flowsheet under proper reagent system, which has absolute advantage compared with routine flowsheet. Actual ore sample of compound magnetic separation concentrate were processed successfully both open and closed circuit experiment through this new flowsheet. SEM and EDS were used to probe the reason why carbonates affect the regular processing. It is analyzed that moderate floatability of siderite and its coating on the surface of hematite and quartz make the phenomenon ?concentrate and tailing no separated?. This research provides a reasonable processing scheme for iron ores containing carbonates and can be used for reference in processing other complicated, refractory iron ore.

Jan 1, 2014

By B. Das

The processing of banded iron ore by direct anionic and reverse cationic flotation to produce pellet grade concentrate is investigated. This low-grade iron ore, known as banded hematite quartzite (BHQ) contains 41.8% Fe, 41.5% SiO2, 1.2% Al2O3, and 0.5% LOI. The flotation behavior of BHQ is studied by varying the effect of concentration of collector, frother, dispersant and pH. Oleic acid and dodecylamine are used as the anionic and cationic collectors respectively. The parameters that gave the best results in cell flotation are utilized in 100 mm diameter flotation column. All the results are compared with regard to the iron grade and recovery in concentrate. It is observed that, anionic collector with dispersant dosage of 220 g/ton, at pH ~8.5 is selective and yielded a high-grade iron concentrate with low silica as impurity. Also, it is possible to achieve an iron concentrate with 64% Fe at 30-37% weight recovery. The characterization studies of the BHQ ore using X-ray diffraction (XRD) technique and liberation analysis with QEMSCAN® are carried out. The sample contains 58.8% hematite and 37.7% quartz and the liberation of hematite particles are found to be 90.3% in -25 µm size. An alternative statistical modeling approach called response surface methodology was also undertaken to optimize the operating parameters in order to maximize the iron grade and recovery. The predicted results by the model are in agreement with the experimental values.

Sep 1, 2012

By G. G. Dong

This paper presents BF flotation machines in brief which are manufactured by Beijing General Research Institute of Mining & Metallurgy (BGRIMM). Dimensional analysis and similarity criteria have been used to scale up BF flotation machines. These scale-up criteria can be used to determine mechanical structure and hydrodynamic parameters including mixing, solids suspension, air transfer and power and so on. Similarity criteria are used to design 40m3 flotation machine being based on data from 1.2 m3 to 20 m3 flotation machines. Hydrodynamic tests of 40 m3 flotation machine in water are discussed.

Jan 1, 2014

By J. E. Gebhardt, D. McBride, T. N. Croft, M. Cross

"Heap leaching is well-established as a relatively low-cost and low-energy method of extracting metals from low grade ores. However, the design methodology, attention to the engineering details during heap construction and the long time scale in metal recovery makes the process susceptible to significant variation in the success of a heap leach operation. Often the laboratory predicted recovery rates are not achieved on site due to poor understanding of the complex physics of flow and coupled solid-liquid-thermal reactions within the multi-dimensional heterogeneous ore body. Given the large scale of commercial operations, small changes in metal recovery can substantially change the operating profitability. While there are a variety of approaches to heap leach modeling, computational fluid dynamics (CFD) modeling coupled with leach kinetic models offers a methodology to describe and understand the complexities of heap leaching. The CFD model uses leach kinetics specific for the mineralogy of the ore, including gangue chemistry, and provides an energy balance to calculate and predict temperature. Coupled with the CFD model’s inherent capability for modeling complex fluid flow, the physics and the chemistry of the heap can be simulated. This provides a tool for engineering design, as well as forecasting heap production under different scenarios. The calibrated model is used to simulate a three-dimensional test heap under fluctuating meteorological data, such as precipitation events, periodic solution application, and notably temperature. These simulations provide support for a methodology to design and engineer heap leaching of low grade copper sulfide ore. INTRODUCTION Worldwide copper ore reserves are faced with decreasing head grades with copper sulfides, particularly chalcopyrite being the predominant mineralogy (Nesse, 2000). Heap leaching offers an economical way to recover copper from low grade ore. The ore is stacked and a leach solution is applied and allowed to trickle though the porous bed of ore to extract target metals. The heap can be built with run of mine material or crushed ore and is constructed in order to achieve percolation of the leach solution to all regions. Bartlett (1998) provides an authoritative overview of the solution mining process where the leach solution interacts with the solid, the lixiviant dissolves the target minerals from the solid into the solution, and the dissolved species are transported out of the heap for subsequent recovery. Petersen (2016) provides a recent review of heap leach technology and emerging and potential future applications, and Ghorbani et al. (2016) summarizes the current state and challenges of the technology. Early applications of heap leaching offered a low cost technique to achieve high recoveries from oxide ores, typically greater than 70% depending upon the kinetics of reaction. As world copper resources transition to mainly copper sulfide mineralogy, such as chalcopyrite based ores, achieving high recovery from these copper sulfide deposits is proving more difficult due to the complexity of the leach kinetics, which leads to low leaching efficiency."

Jan 1, 2018

By Alok Tripathy

A simulation code called SIMJIG and the user interfaces have been developed using discrete element method (DEM) and the .NET platform respectively for the jigging process. DEM platform is used for tracking of particles in the jigging operation. DEM uses the net force balance on the particles to track the trajectory of the particle. Simulation results are compared with experimental results obtained by jigging of low grade iron ore lumps. Two different iron ore samples one from Chatishgarh and one from Odisha were used for the experimental studies. The Alljig? stratification test rig meant for batch laboratory experimental studies has been used in the present work. The behavior of different sizes of material on jigging has been examined. Later, the particle size behavior during jigging at different layers of the jig bed has been studied. Further stratification profile across the jig bed has also been studied. It was observed that simulation results are matching quite nicely with the experimental results. The SIMJIG simulator developed in the present study could be used for predicting the performance of the jigging operation effectively. Keywords: DEM, gravity concentration, jigging, iron ore, simulation

Sep 1, 2012

By Pramila Misra, Jibardhan Meher, Debadutta Das

The concentrated coal-water slurry has been receiving considerable attention recently due its ability to replace fossil fuels. Attainment of stable and concentrated slurry has been succeeded so far through several physical and chemical techniques. The present article reports the formulation and stabilization of a highly concentrated coal-water slurry formed from five varieties of non-coking coals with variable ash contents obtained from Eastern part of India, employing three varieties of starch esters, such as starch benzoate, starch formate, and starch carbamate as dispersant. The apparent viscosity of the modified coal-water slurry has been measured by varying coal loading, dispersant percentage, pH, temperature, etc. The apparent viscosity of the slurry has been found to be decreased substantially on addition of 0.8% of adsorbate in the slurry. The particle-particle interaction has been considerably decreased and stable concentrated coal-water slurry containing high weight fraction of coal (61.5-63.5%) has been achieved in each case. The slurries stay in a non-settling form for about a month with viscosity in a permissible low range. The coal-water slurry has been found to behave as a non-Newtonian liquid. Comparison of the zeta potentials of the naked and modified coals evidences that adsorption of the dispersants at coal-water interface results in inhibition of the agglomeration of coal particles through mostly steric repulsions.

Jan 1, 2014

By Gautam Chandra Mondal

An attempt has been made to carry out qualitative assessment of mine water discharges from the different mines of West Bokaro Coalfields of Hazaribag district of Jharkhand, India. A total of 33 mine water samples were analyzed for pH, electrical conductivity (EC), major cations (Ca, Mg, Na, K), major anions (HCO3, SO4, Cl, NO3), and heavy metals (Fe, Mn, Cu, Zn, Pb, Cr, Ni, Co, As). The hydrochemical data has been evaluated in terms of major ion chemistry, solute acquisition processes and suitability of mine water for domestic, industrial and irrigation uses. The pH of the analyzed mine waters varies from 5.27?8.43 indicating acidic to alkaline nature of the water. The electrical conductivity (EC) values varied from 276 µScm-1 to 1598 µScm-1 for measured samples and spatial differences between the EC values reflects the wide variation in lithology, surface activities and hydrological regime prevailing in the region. The anion chemistry of the analyzed water samples shows the dominance of SO4 and HCO3 with a minor contribution from Cl, NO3 and F. The observed high values of sulphate in the mine water of the area may be attributed to the oxidative weathering of pyrites. On average chloride is contributing 5% of the total anionic balance (TZ-). Fluoride and nitrate have low concentrations and on average contributing <2% the total anions. The cation chemistry indicates that 79% of the samples are Ca>Mg>Na>K, while the 6% belong to Ca>Na>Mg>K and 1% of Ca>Mg>K>Na. Weathering of rock forming minerals and cation exchange processes normally control the levels of these cations. Concentrations of some heavy metals (Fe, Mn, Ni, Cr) are found to be well above the prescribed permissible levels recommended for the drinking water. The water quality assessment for drinking purposes indicates that most of the mine water having high TDS, total hardness (TH) and sulphate concentrations. This suggests that mine water of the study area is not suitable for direct use in drinking and domestic purposes and needs a proper treatment before its utilization. The assessment of water for irrigation uses show that the water is good to permissible quality and can be used for irrigation uses. However, high values of salinity, %Na, SAR, RSC and Mg-hazard at certain sites restrict its suitability for agriculture uses. Keywords: mine water; ion chemistry; quality assessment; West Bokaro coalfields

Sep 1, 2012

By Ashutosh Shandilya

Froth flotation is a selective separation process and rarely used for beneficiation of limestone in the world as compared to other minerals and also mostly known conventional methods of up gradation of ROM including wobbling, selective mining, sorting, preblending etc. Limestone is mainly used in the manufacture of cement, steel and chemical industries. High grade limestone deposits are depleting day by day and the requirement of the industries have to be met by beneficiating the low grade limestone deposits in the world. And because of marginal quality of limestone, it cannot be directly used in cement industry. At ACC Madukkarai cement works, Coimbatore, Tamilnadu, full fledged mineral beneficiation process is adopted to enhance the quality of low grade lime stone from 38-42 % CaO to 45-47 % CaO and silica reduced from 19-22 % to 11-13 % by use of oleic acid (commercial grade and vegetable origin) 0.38 kg/ton of limestone and caustic soda 0.05 kg/ton of limestone. Keywords: OK-8 Cells, Froth flotation process, Beneficiation studies, Low-grade lime stone, Oleic acid, % solids, Pulp density, Ph, Iodine value, saponification value, Denver cell

Sep 1, 2012

By B. Orberger

The fine fraction (< 2 mm) of the high grade Mn-ore from the world class Moanda deposit, Francevillan basin, in Gabon, contains up to 30 wt. % of manganese and about 0.4 wt. % phosphorous. A pilot study at laboratory scale integrating mineralogy and geochemistry before and after ultrasonic treatment was conducted on the fine fraction (< 2 mm) of oxidized Mn ore in order to reduce the phosphorous content and enrich this fraction in manganese. The fine fraction was dried, crushed at 2 cm and sieved at 2 mm. The two fractions (< 2 mm and 2 mm ? 2 cm) were investigated by X-ray diffraction and scanning electron microprobe ? electron dispersive spectroscopy analyses. Both fractions contain lithiophorite, cryptomelane and pyrolusite as Mn carrier, and goethite, muscovite, illite and quartz as contaminants. The Mn hydroxide nsutite was only found in the fraction 2mm ? 2 cm.The < 2 mm fraction is significantly richer in goethite, muscovite/illite, and quartz. Phosphorous carriers are mainly goethite (up to 2.8 wt. % P2O5), while the Mn minerals contain up to 0.8 wt. % P2O5. The Mn minerals are partly included in an agglomerate of goethite, muscovite/illite, and quartz. The < 2 mm fraction was treated by ultrasound for 30 s in normal water. Mineralogical and chemical analyses after ultrasound treatment showed that the Mn-minerals were largely liberated from the goethite-muscovite-illite agglomerate. Mass balance calculations show that after ultrasonic treatment the < 2 mm fraction was ? 50 % enriched in Mn and ?50 % impoverished in P.

Sep 1, 2012