Search Documents

By S. R. Nandargikar

Construction of open foundations for the Second Thane Creek Bridge was indeed a challenging task. Some major problems were encountered during the construction of foundations for pier No. P22 (S/N), P.6(S) and P.12(S) of this bridge. This paper describes these problems briefly and also highlights how they were solved.

Jan 1, 1996

By Slav Tchepak

The King's Wharf development is located in Sydney's Darling Harbour area. The site was originally used for industrial maritime purposes, which over the years has been reduced to accommodating leisure craft only. The site has been filled with various materials, resulting in fill materials varying from soils, to concrete and rock fill. A prestigious new residential development at the site required piles to found in Sydney sandstone that occurred at depths ranging from 1 to 27m. The selection of appropriate pile types is discussed, as are details relating to the design and construction of cast insitu Omega piles and CFA piles. A number of issues needed to be addressed relating to the piling, including the design of the piles, the potential for liquefaction of the fill material due to earthquakes, penetration of the piles through the fill materials, installation of the piles to a satisfactory positional tolerance and pile performance. A number of piles were dynamically tested to prove pile performance and these results are presented and compared with design expectations. The project was successfully completed on time and budget, indicating the selection of pile types in the difficult ground conditions to be appropriate.

Jan 1, 2000

By Lori A. Simpson

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the three-level basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tied-back soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

By Peter Cali, Wesley Schmutzler

"The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.IntroductionDuring hurricane Katrina the levee that constitutes LPV-111 was overtopped and breached in several locations. The United States Army Corps of Engineers (USACE) was presented with the task of increasing the level of the flood protection around New Orleans after Hurricane Katrina to the 100- Year hydraulic grade - the level of protection that provides risk reduction from a storm surge that has a 1% chance of being equaled or exceeded in any given year - and the firm project completion deadline was June 2011.LPV-111 is located in East New Orleans and a large portion of the levee is adjacent to the Bayou Sauvage National Wildlife Refuge. The levee could not encroach on this area. This provided a limited footprint for the levee and made construction of conventional levee difficult, if not impossible. The total length of the project was 5.3 miles. Included in the project was the rehabilitation of one main pumping station and one smaller pump station for water management within the refuge. Short sections of “T” wall were used at the tie in at the Lake Borgne Surge Barrier, the main pump station and the CSX Railroad crossing"

Jan 1, 2017

By John L. White

The vibro driver/extractor is a machine that grips to a pile and vibrates it up and down. When the vibrating pile is lowered into the ground, all soil around the pile begins to vibrate. A vibrating pile breaks the friction between the pile and the soil, thus allowing it to penetrate the ground. A vibro is usually operated by hoisting it into the air with a crane and then placing it onto the pile. The vibro has hydraulic gripping jaws that are controlled from the ground. Once the operator has successfully lowered the vibro onto the pile, the jaws are closed and locked onto the pile and operations can begin. Please see the drawing below: [ ]

Jan 1, 1990

By J. Erik Loehr, Minh Uong, Andrew Z. Boeckmann, Sarah G. Myers

"The University of Missouri performed a lateral load test program involving 32 drilled shaft load tests for the Missouri Department of Transportation (MoDOT). Tests were performed at two MoDOT geotechnical research sites, and all shafts were founded in shale. Shafts were instrumented to measure the displacement of the shaft head, and the structural response of each shaft was interpreted from strain gage data and from ShapeAccelArray (SAA) data. The SAA is a chain of rigid segments with sensors that use MEMS (microelectromechanical systems) technology to measure the tilt of each segment/joint. The measuring principle of the SAA is therefore similar to that of an inclinometer. The SAA device was placed in a casing installed in the center of each test shaft to provide a continuous record of deflection along the length of the shaft throughout each test.Bending moment profiles were calculated from strain gage data and from SAA data. Interpretation of bending moments from measurements of strain (via strain gages) and displacement (via SAA) is a nontrivial exercise, primarily because the bending stiffness, EI, is nonlinear and greatly influenced by concrete cracking, which is difficult to predict. The procedure used for this work predicted values of bending stiffness along the length of the shaft as a function of the bending curvature, which was interpreted from the SAA data. Values for bending stiffness as a function of curvature were computed using Ensoft LPile v2012. Bending moment profiles from SAA data were typically similar to those from strain gage data. The SAA bending moment profiles were often “noisier” than the strain gage bending moment profiles, but the SAA bending moment profiles had more data points since the SAA chain was continuous from the top to the bottom of each shaft."

Jan 1, 2017

By Lee S. Vanzler

Atlantic Wharf involved the construction of a six-level underground parking garage and a 32-story high rise tower along the historic Boston Harbor waterfront. The site, historically known as ?Russia Wharf,? consisted of filled land initially created in the late 1800s by extending the shoreline toward the harbor as the urban population and land needs grew to support expansion of commerce and trade. Redevelopment required solutions to address relics of waterfront structures (granite block seawalls, piles, and piers), weak subsurface soil conditions, tidal groundwater levels, and contaminated soils resulting from previous site usage and filling. The foundation system, consisting of drilled shafts with column loads up to 14,000 kips (62,272 kN), concrete diaphragm wall (slurry wall), and up-down construction methodology, was chosen to address these factors. As a prerequisite for development, selected portions of the façades of the former historic buildings were required to be preserved, protected, and incorporated into the final building configuration. The historic façades were temporarily braced and supported prior to the demolition of the buildings and commencement of below-grade construction. This paper will describe the considerations in the selection of up-down construction methodology along with a discussion of the design and performance of the concrete diaphragm wall and drilled shaft foundations. Up-down construction methodology shortened the overall construction schedule while addressing the lateral bracing requirements for the concrete diaphragm wall and restrictive ground movement tolerances to protect adjacent structures. Below-grade construction was completed in March 2010, and the building was opened for tenant occupancy in January 2011.

Jan 1, 2011

By Arash Saeidi Rashk Olia, Dunja Perić

The increasing demand for renewable energy has attracted attention to energy geostructures as means of extracting clean geothermal energy from the ground. To further advance the understanding of soilstructure interaction in energy piles analytical solutions considering the self-weight of the pile were derived. These solutions were then incorporated in recently-derived thermomechanical weightless solutions to provide comprehensive analytical solutions for axial displacement, strain and stress in single energy piles. This was accomplished by comparing responses of energy pile under different loading scenarios that reflect presence and absence of the self-weight. Results of mechanics-based analysis revealed that the self-weight of energy piles embedded in stiff soils has no significant contribution to displacement, strain and stress that develop under thermo-mechanical loads. Overall, the significance of the self-weight contribution depends on the magnitude of thermal load as well as the soil-pile interface stiffness. The stiffness of end restraints imposed to the pile head and tip were also found to play an important role in contribution of self-weight in induced thermomechanical stresses in energy piles.

Oct 1, 2022

By K. Rainer Massarsch

"Part 1 of 2 By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenINTRODUCTIONConstruction activities, such as driving of piles and sheet piles, soil compaction or excavation generate noise and vibrations. In populated areas these can have a negative impact on the environment, disturb inhabitants and, under unfavorable conditions, cause damage to buildings and installations. This condition is aggravated by the growing public awareness of environmental issues and the increasing use of vibration-sensitive electronic equipment and machinery in industry. In many countries, environmental regulations are enforced more stringently and limit or even prohibit the use of impact or vibratory hammers. This development has restricted the use of cost-effective foundation methods, such as driven and vibrated piles and sheet piles.Vibration problems are gaining importance in many European countries and extensive research has been performed during the past decade, especially with respect to traffic vibrations (Massarsch, 2004). Significant progress has been made owing to the availability of high-quality field measurements and an improved theoretical understanding of how vibrations are generated and transmitted through soil layers. These findings can also be applied to vibration problems associated with construction activities. However, this information is not yet appreciated by the geotechnical profession and even less by the construction industry.This paper discusses the effects of ground vibrations on the surrounding soil and on buildings, with particular emphasis on the different mechanisms of damage that may occur. Guidance is given on the elements which should be taken into account in an assessment of risks associated with piling projects. A simplified method is proposed for assessing the risk of settlements or strength loss in soil deposits. Limiting vibration levels are presented, based on the Swedish standard, which can be used to assess the risk of damage to buildings. Aconcept to predict ground vibrations caused by pile driving and the mechanisms which control the propagation of ground vibrations, will be presented in the second part of this paper."

Jan 1, 2004

By James L. Christensen, Gregory Sanchez, Michael P. Walker

The Fogg Museum expansion project required excavation and construction in a congested urban area in Cambridge, Massachusetts. A soldier pile tremie concrete (SPTC) wall provided the support of excavation and now serves as the permanent basement wall of the new expansion of the museum. The existing Fogg museum had a single basement level. The new expansion has a two-level basement for new exhibit space and an amphitheater. The east side of the site is about 20 feet above the basement level of the existing Fogg structure which resulted in a significant unbalanced load that needed to be resolved without damaging the original Fogg structure. The SPTC wall was supported with a combination of tiebacks and internal bracing. The final depth of the excavation was about 40 feet below street level. Strict movement control was imposed because the existing museum contained an Italian Renaissance-style courtyard. The southeast corner of the SPTC wall had to accommodate underpinning of an historic concrete ramp which was ultimately incorporated into the expansion. Challenges during construction included excavating the SPTC wall panels up to 12 feet into argillite bedrock which had occasional diabase dikes and sills. The following topics are discussed in more detail after a general project.

Jan 1, 2015

By Pratik Goel, Sumanta Haldar

High-speed rail is an emerging area of interest in India. The Government of India is implementing prestigious bullet train projects in various parts of the country. High-speed rail (HSR) will be operating in India at about 320 kmph at an elevated track on a viaduct for most of the ongoing and upcoming corridors. High-speed projects in India necessitate an indigenous solution for design applications for viaduct design. Pile groups are extensively used in viaducts for high-speed trains, as they can be a settlement reducer and increase the bearing capacity. Post-construction settlement of pile foundation for high-speed railway viaduct is a concern of engineers. Limited attention has been paid to estimating the post-construction settlement. This paper aims to propose a prediction of the cumulative settlement of pile groups due to cyclic train loading. A three-dimensional finite element model (3D-FEM) of the pile group is established in Abaqus CAE. A suitable plastic model is used to simulate the subsoil. The pile group is modelled as an isotropic-elastic element. The study examines the influence of cyclic loading time and train speed on the settlement of the pile group. The analysis is carried out considering various single pile and pile group parameters like S/D, Ep/Es, L/D, Pile cap thickness, etc. and finally, an optimum configuration is suggested.

Sep 1, 2022

By Andrew Moran, William H. Walton, Matthew D. Emrick, Mary C. Nodine

"A rapidly growing company in the northern US needed a large auditorium built into a dolomite bedrock hillside. The structure required an 80-foot-deep earth retention system independent of the auditorium foundation and superstructure. Allowable wall movements were limited to less than two inches. A 60-foot-tall permanent shotcreted soil and rock nail wall was designed for excavation support. The soil and rock nail wall utilized both active (post-tensioned) and passive nails, with capacities and installation angles optimized to address varying soil and rock conditions and to support heavy surcharges. The wall was configured with three two-foot-wide benches to facilitate controlled blasting and removal of more than two million cubic yards of soil, limestone and dolomite bedrock, and featured a permanent cast-in-place concrete face and a robust waterproofing and drainage system. A 20-foot-high reinforced concrete retaining wall was required at the top of the soil and rock nail wall to raise grades, resulting in a large surcharge.Design of the soil and rock nail wall was initiated less than three months before the start of construction, requiring expedited geotechnical explorations, analyses, design, and construction that would occur simultaneously. Design changes were made to address the discovery of a weak clay residuum seam at depth running along the base of the excavation, as well as significant changes to the building footprint made after the start of construction. Extensive performance monitoring was conducted during construction to measure vibrations and movements.Introduction and Project BackgroundA fast-growing company in the northern United States had a need for 600,000 square foot, 11,000 seat auditorium as part of its campus expansion. The auditorium was built underground, into a hillside to preserve the views of rolling terrain and farmland beyond. It featured a green roof and rockwork facing that mimicked regional geologic formations. The sixstory building required up to 80 feet of earth retention, including 60 feet of excavation beneath existing grades.As concepts for the project evolved, it became apparent that due to the geologic conditions, space limitations on site and the depth of cut required, a standard counterfort wall system would not be feasible. With groundbreaking for the building three months away, Thornton Tomasetti (structural engineer) engaged GEI Consultants, Inc. (wall design engineer) to design a 1,600-foot-long permanent soil and rock nail wall to support the excavation. The wall design engineer implemented a geotechnical exploration program immediately and began the design process, coordinating closely with Nicholson Construction (specialty"

Jan 1, 2017

By Joel Moskowitz, George J. Tamaro

"A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140m by 100m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations, the seam dipped below rock that is more competent. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half. The tower covering the south half of the site was topped out in 2002 and the garage levels in the north half of the site were completed in 2003.PROJECT DESCRIPTIONIn September 1999, a major investment company began the due diligence process to evaluate a property on the shore of the Hudson River in Jersey City, New Jersey for a new multi-use complex. The site offers a spectacular view of lower Manhattan directly across the river from the site of the former World Trade Center. The site, covering two city blocks, was previously occupied by manufacturing and office facilities of Colgate-Palmolive.The building footprint is approximately 140m by 100m, the southern half of which is occupied by a 260m tall office tower, shown in Fig. 1. As of this writing, design of the structure for the northern half of the site has not been finalized, but it is expected to comprise an 11-story office building. A glass-covered atrium will occupy the street that formerly separated the two blocks. As part of the due diligence process and preliminary design evaluation, alternatives were considered to accommodate various numbers of parking places, both above and below existing grade. A major consideration for below grade parking is the proximity of the Hudson River some 25m east of the east building line."

Jan 1, 2004

By Moritz Schleeh, Christian Moormann

Temporary working platforms are generally required in order to ensure that heavy construction machinery such as drilling and trench wall units, pile drivers, vehicle and crawler cranes can be set up safely at the site of operation. Considering all possible operating and loading conditions, especially on ground of low shear strength and stiffness, the design and construction of temporary mobile working platforms needs to be considered more as a serious engineering task than as a second order structure of minor relevance. Working platforms reinforced with one or several geosynthetic layers have proven to be especially effective with regard to stability, serviceability and durability but their design requests even more sophisticated approaches. Existing design models are often based on simplified assumptions and do not consider the complex interaction between construction machinery, working platform and subgrade. Non-monotonic loading as well as elastoplastic and time-variant deformation of cohesive subsoil can adversely affect the base layer system and the serviceability and stability of the construction machinery operating on it. In this context, there is a need for improvement of design approaches and their optimisation considering that there are no generally accepted design approaches or technical codes of practice available for the design of temporary working platforms. The present paper deals with the multifaceted and non-trivial interaction effects of working platforms investigated by model tests, field measurements and numerical simulations to develop a design approach that ensures a safe installation and operation of heavy plants on unstable ground.

May 1, 2022

By John Mould, Gordon Chen, Michael Oakland, William McElwee

"This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system. IntroductionThe Willis Avenue Bridge is one of the major access ways from the Bronx into Manhattan. The location is shown on Figure 1. The original bridge constructed in 1901 was a swing bridge over the East River. The bridge was in disrepair and outdated with regards to its ability to handle the flow of traffic resulting in numerousaccidents.In 2007, Kiewit Constructors Inc./Weeks Marine, Inc., A Joint Venture was selected to construct a replacement bridge. The $612 million project included construction of a new bridge just to the south of the original bridge. The most notable aspect of the construction was floating and lifting the new 350 ft. long swing span in place as a single piece. However, another significant challenge was using blasting to demolish two of the abandoned piers which were within the East River. The blast would be near existing structures in both Manhattan and Brooklyn and would be within 30 ft. of the new bridge."

Jan 1, 2017

By M. Kitazume, H. Imai

The deep mixing method was developed in Japan and put into practice in the middle of 1970s. Since then, the wet and dry type methods have been applied for various improvement purposes in Japan. One stork of mixing tool produces a column shape of stabilized soil in a ground. By the series of productions, arbitrary shape of improved ground can be constructed by overlapping each columns. It is specified to complete the overlapping within 24 hours in order to ensure the tight connection of the columns. However, it can not be completed within the specific time in some cases due to bad weather or machine trouble, which causes a cold joint in the improved ground. In this study, the influence of the cold joint to the behavior of the block type improved ground is examined by a series of centrifuging model tests and FEM analyses. It is found that the ground behavior is influenced by the position of the cold joint, where the cold joint at the sea side shows a little influence to the behavior but one at the port side causes large decrease in the stability of the improved ground.

Sep 8, 2021

By Michael Oakland

This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system.

By Dan Mahrt

"In June of 2009, a slope failure occurred along River Road in Bismarck, North Dakota. The slope failure affected approximately 300 feet of River Road with vertical displacements up to 3 feet, resulting in closure of the road. River Road travels along the Missouri River in Bismarck in a geologic area riddled with historic slope failures of varying sizes. River Road is a city roadway which travels along the Missouri River. The toe of the failure extended into the Missouri River, therefore methods to repair the slope needed to be constructed within United States Army Corps of Engineers (USACE) requirements, and be acceptable to the City of Bismarck. As this is a scenic area along the river, the stakeholders desired to maintain the scenic landscape along the roadway as a part of the slope stabilization.Due to the magnitude movement of the failure mass, the geometry of the failure was relatively easy to evaluate. In evaluating remediation options and collaborating with the USACE, the team determined that the scarp was situated primarily within the navigable portion of the Missouri River. This required USACE approval for any repair or remedial work downslope of the roadway. The City of Bismarck wished to reopen the roadway as soon as possible, therefore stabilization options were limited to working within the road right-of-way to avoid permitting for working within the navigable waterway.The remediation solution for this project involved a combination of driven H-pile and placement of lightweight fill to re-construct the roadway at the original grades, and avoid impacting the navigable portions of the Missouri River. This paper discusses the unique project constraints and the innovative solution using multiple technologies to successfully stabilize the slope.BackgroundIn June 2009, Bismarck, North Dakota experienced two consecutive days of significant rain resulting in over 5 inches of precipitation in a 36-hour period. Shortly after these rain events, a slope failure was noted on River Road, a city street along the Missouri River in Bismarck. Initial findings noted the slope failure affected about a 300-foot long portion of the roadway, with vertical displacements of about 2 feet. The city of Bismarck closed the roadway and began evaluating repair solutions for the road."

Jan 1, 2016

By Suzanne R. Hess-Brittelle, Sharon L. Schulz, Tyler J. Quick, Amy F. Ebnet

"Abiquiu Dam is a rolled earth fill dam with impermeable core located on the Rio Chama in New Mexico. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. During the 1960’s and 1970’s, the grout curtain was extended 1,000 ft. into both abutments and sections of the foundation beneath the embankment were regrouted. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during multiple phases of supplementary grouting and during verification drilling following the 1970’s grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. The fluid losses in the embankment may be related to seasonal shutdown layers in the embankment or benches in the abutment foundations. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment.INTRODUCTIONAbiquiu Dam is located on the Rio Chama in New Mexico and consists of a rolled earth fill dam with impermeable core, controlled outlet works, and an uncontrolled rock-cut spillway. The dam was authorized for flood control and sediment retention and was designed as a dry dam, holding flood pools for relatively short durations. The foundation is comprised of Permian and Triassic age, interbedded mudstones and sandstones that were deposited in an active braided stream system. Sandstones are moderately fractured and have variable aperture and infilling. Generally speaking, joints are near vertical. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. In 1966-1968, the grout curtain was extended 500-ft into the left abutment and the foundation beneath a 560 ft. section of the embankment was re-grouted. In 1978-1980, the grout curtain was extended 1,000 ft. into the right abutment, an additional 500 ft into the left abutment and the foundation beneath the right 520-ft section of the embankment was re-grouted. The alignments of these grout programs are shown in Figure 1. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during both phases of supplementary grouting and during verification drilling following the 1978-80 grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment. This paper provides a summary of the drilling and grouting methods used during these programs and the potential for damage to the embankment."

Jan 1, 2016

By Kazuyoshi Kamimura, Masaya Kawata

"It has been 30 years since the cement deep mixing (CDM) method developed in Japan. CDM method has been applied to many structures. While various technical improvements have been implemented in the meantime, the single-axial and double-axial technologies used at the time of its initial development are still prevalent.In response to the recent trend of reducing construction costs, we developed a triple-axial CDM method called the “Lemni 2/3 Method.” This method uses two lemniscate motions caused by newly developed auxiliary stirring devices and employs a double-axial injection method in which the cement slurry injection takes place only from the outer two axes. In this way, it is possible to create a stabilized body around the three axes. Moreover, this method does not require substantial equipment investment as conventional construction machine and facilities can be used without modification and large volume work is possible.With these technologies, this method can achieve a substantial reduction in the construction period and cost, while ensuring the same level of improvement quality as conventional methods. As a result, this method is being applied to ground improvement work in a variety of places.Lemni 2/3 Method was first put to practical use in 2004. Since then, the method has been used for ten projects. In this paper, we show some application examples of this method.OUTLINE OF TRIPLE-AXIAL CDM METHOD (LEMNI 2/3 METHOD)In the newly developed CDM method (Lemni 2/3 Method), work efficiency is improved by employing triple-axial stirring blades instead of the conventional single- or double-axial type. Existing conventional construction facilities for double-axial type can be used with only minor equipment additions, because the cement slurry injection takes place only from the outer two axes.Construction Machine and Construction MethodThe combination of major construction machines of the Lemni 2/3 Method differs little from the standard specifications of the double-axial type as shown in Fig. 1. Existing work control equipment can be used without modification, which is further evidence of the simplicity, convenience, and economy of the new method. The Fig. 2 photo shows a full view of the construction machine, and the Fig. 3 photo shows the stirring blades and the auxiliary stirring devices. The work procedure for the Lemni 2/3 Method is shown in Fig. 4."

Jan 1, 2015