Search Documents

By Y. El-Mossallamy

The piled raft foundation was extensive applied in the last two decades in different soil conditions e.g. in soft to stiff clay as well as in medium to dense sand and even in highly weathered rock. The piled raft is now applied not only to control the foundation settlement but also to minimize the required raft thickness to reach the most economic foundation design. An innovative application of the piled raft is its special adjustment to cases of foundations with large load eccentricities or very different loaded parts of buildings to avoid the need of settlement joints, which are especially complex below ground water table. Recently, the piled raft is applied for foundations of highway and railway bridges with special serviceability requirements regarding the allowable total and differential settlement as well as tilting. Actually numerical analyses are the mostly used design methods for piled rafts. For all day design practice a simple and modest design method is highly needed -at least in the first design stage- to check the feasibility of the piled raft on the specific project conditions. In this paper, a general overview on the recent innovative applications of piled rafts in Germany will be presented in a short overview. The results of the simple design method will be discussed and compared with the results of more enhanced numerical methods.

Jan 1, 2006

By Koichi Kobayashi

Performance-based approach to design of structures including foundations was adopted after enforcement of the revised Building Standard Law in Japan in 2000. The use of piled-raft foundation is favorable for medium-rise buildings in soft ground because of its good performance. In the design of the piled-raft foundation (Architectural Institute of JAPAN2002), vertical load is usually carried by the raft foundation, while the pile is primarily meant to control settlement of the structure. Shaft friction is expected to be larger in a nodular pile(Karkee, et.al., 1998) since it has larger surface area than a straight pile, and such piles are frequently used in piled-raft foundations. Since few structures with piled-raft foundation exist currently, the settlement characteristics of piled-raft foundation have not been fully clarified. To design piled-raft foundations with better confidence, the mechanism of vertical bearing capacity and the spatial distribution of settlement should be clarified, for which the actual behavior of the building-foundation system needs to be evaluated. This paper presents observations of settlement of a building with a piled-raft foundation at a soft ground site. The building is a steel structure covering an area an 766 m2, and consists of two-storey office block and one-storey warehouse block. The filled ground of about 5-m thickness at the ground surface is underlain by approximately 4-m thick alluvial sand layer below which lies about a 17-m thick alluvial clay layer with SPT N-value less than 2. The piles used in the piled-raft foundation are 12-m long nodular piles with nodal diameter of 500 mm (pile shaft diameter is 400 mm). The bored pre-cast piling method (Karkee, et.al., 1998) was used to install the piles. To evaluate the foundation settlement, the method of analysis of three-dimensional frame system, utilized widely in Japan, was adopted in combination with the foundation system. Basic assumptions were: (i) total ground settlement is evaluated as the sum of immediate settlement and consolidation settlement, (ii) immediate settlement is evaluated from the Mindlin?s solution in which strain dependency of shear modulus of soil is considered, (iii) settlement in clayey layers is evaluated by the one-dimensional consolidation theory, and (iv) shear spring between soil and pile shaft is represented by a hyperbolic function. The applicability of the method of analysis was verified by comparison with results of field monitoring of building settlement.

Jan 1, 2006

By Steven R. Musselman

The bending strength and flexural stiffness of a micropile at its threaded connection is less than its intact strength and may fail due to thread slippage or by fracture through the pin (reduced cross-sectional area of male threads in the threaded zone of the casing). The mode of failure depends on the reduction in cross-section necessary for machining the threads, and details of the threaded connection such as the length of threaded connection, size and shape of threads, and the thread density (threads per inch). Based on data from bending tests conducted on 9-5/8 inch diameter micropile casing, a method has been developed to predict the ultimate moment capacity and initial bending stiffness of round threaded micropile connections. Two modes of failure were observed from four-point bending tests conducted at the University of Illinois on 9-5/8 inch casing with round threads. Threaded micropile casing connections with an effective thread length of 1.35 inches typically failed by slippage at the threads (jump out), while connections using an effective thread length of 1.89 inches failed by fracture of the pin. These two failure modes were described by W.O. Clinedinst in his report to the American Petroleum Institute on tension tests of threaded pipe casing. Clinedinst developed an empirical formula to determine the tensile strength of threaded connections. A method to predict moment capacity for threaded micropile connections by modeling the micropile cross-section and applying Clinedinst?s equation to determine the max tensile stress along the threaded connection while satisfying force equilibrium is proposed. The predicted moment capacity for threaded connections using this approach is within ten percent of measured for both modes of failure observed from the bending tests.

Jan 1, 2007

By A. K. Bhattacharya

Cylindrical bridge piers are widely used and equations exist that can predict the maximum depth of local scour around such piers. Scour around piers is an undesirable phenomenon, as it requires the foundation to be placed to a greater depth resulting in increased cost, making it worthwhile to investigate scour-reducing measures. A number of scour-reducing measures have been tried out for cylindrical bridge piers including placing a concrete collar around the pier, having a delta-wing projecting upstream in front of the pier, placing riprap around the pier, using a group of piers instead of a single pier, having a slot in the pier aligned in the longitudinal direction. The objective of this study is to investigate the effect of upstream protective piles on reduction of maximum local scour depth around a cylindrical bridge pier. The upstream piles are placed at different radial distances in front of the pier and the scour depths are observed. The proposed equation of Dey (1997) for determining the maximum depth of scour around a cylindrical bridge pier is used. The reduction of local scour around the pier is compared with local scour around an unprotected pier.

Jan 1, 2009

By David A. Jack

The Mission Valley Viaduct is located in San Diego, California. This structure is the intersection of Interstate 8 and 805. The project consists of the main viaduct, 8 connecting ramps, and one highway overpass. This job was originally built back in the 70's. After the Loma Prieta Earthquake in 1989, Caltrans began an aggressive program to seismic retrofit all of its bridges throughout the state. Most retrofit designs required major upgrades to the existing footings. These footing upgrades consisted of either driven or drilled shaft piling. The existing footings of the Mission Valley interchange were supported on driven H pile. The soils throughout the site were dense sands and gravels, cobbles, occasional boulders with a dense sandstone bearing strata, which varied through out the site. It was this sandstone strata that the engineers designed their pile tips around. High ground water in sandy soils created a high probability of liquefaction in all of the upper stratas.

Jan 1, 1998

By Kenneth Gavin

Design practice for piles installed in Irish glacial till has developed in an ad-hoc manner, based on the results of un-instrumented load tests. This had led to designers using similar design parameters for both CFA and displacement piles. To address the concerns of industry a series of instrumented pile tests were performed by two Irish Universities. These tests summarized herein, revealed that CFA piles develop higher shaft resistance than piles driven in glacial till. However, they exhibit low base stiffness and the end bearing resistance that can be mobilized at acceptable pile settlement is low. The use of simple non-linear elastic design approaches to predict the load-displacement response is considered. The methods are used to predict the capacity of two large diameter CFA piles installed in glacial till. While the predictions were reasonably accurate at predicting the initial load-displacement of the piles, significant creep settlement developed at higher load levels. The cause of the creep settlement was investigated through the use of plate load tests and the consequences for pile design are discussed.

Jan 1, 2009

By SungWon Park

The efficiency of the current design methods for computing pile resistances is evaluated using field load-settlement tests results. Twelve load-settlement test data for drilled shafts and bored piles were obtained from the literature. These load-test data were fitted using the ?t-z? method. Subsequently, the ultimate resistances were evaluated based upon the failure criteria from following methods: (1) the Davisson?s approach and (2) settlement corresponding to 5% or 10% shaft diameter approach. The ultimate resistances for these drilled shafts and bored piles were also predicted using methods based on the design code from North America (United States, Canada), Europe, and Asia (Japan). The pile resistances determined from field load-settlement tests were compared with those calculated using the design codes. The comparisons show that most design codes predict a conservative resistance for drilled shafts and bored piles. However, in the case of drilled shafts, we find that some of the design codes can over-predict the resistance and, therefore, should be applied cautiously. This research also shows that ?t-z? method can be successfully used to predict the ultimate resistance and the load transfer mechanism for a single pile.

Jan 1, 2009

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2005

By Amalia Giannakou

This paper utilises 3-D finite-element modeling to study the static and dynamic lateral harmonic response of inclined piles, in a homogenous and a non-homogenous soil, modeled as a linear hysteretic medium. The results of a comprehensive parameter study are presented in the form of dimensionless plots of: (a) static and dynamic swaying and rocking stiffnesses and damping ratios, and (b) distribution of internal forces (bending moment, shear and axial force) with depth. These plots can be readily utilised in practical applications and they offer insight on the role of the inclination in the response of flexible piles.

Jan 1, 2006

By Gustavo Armijo

Slippery and unstable working platforms spoiled not only by natural weather conditions but also by the effects of the construction process (drilling mud, grout slurry) are among the main sources of hazards. Due to this fact a set of recommendations for execution and maintenance of working platforms are presented in this paper, which is based on a study on this subject that is being carried out by AETESS, the Spanish Federation of Geotechnical Contractors. The main objective of this paper is to establish the basis for the right execution and maintenance of working platforms for geotechnical jobs with the idea of increasing safety and productivity. All the aspects involved in working platform safety are analyzed: ground and equipment characteristics, geometric conditions and working platform maintenance. From this analysis a set of general requirements is proposed together with the necessary specific controls before and after the equipment arrival to the job site. In order to facilitate this analysis some flow charts and tables and specific appendixes for each geotechnical technique are included.

Jan 1, 2006

By Steven D. Dapp

The use of base grouting (tip grouting) to enhance the axial capacity of drilled shaft foundations can achieve improvements in economy and reliability for many types of projects and soil profiles. Recent experiences on a range of different construction projects in the Southeastern U.S. illustrate the most attractive opportunities for utilizing this technique and some limitations of the method. The quality assurance provided by measurements obtained during post grouting the pile toe is another important aspect favoring its use; the base grouting is shown to identify weaker piles and provide a means of remediating some deficiencies so that increased foundation reliability is achieved. This paper provides an overview of the methods used to evaluate and design for base grouted shafts along with lessons learned from several case histories.

Jan 1, 2006

By Peng Jiahong

With ultrasonics application during checking the large diameter cast-in-situ pile body, it is usualy applied the statistical method of probability and PSD. This paper presents a converse probabilistic-analytical method which can identify important anomalies, both strong and weak, during interfered situation. So the inhomogeneity in concrete pile may be ellectively distinguished. In order to ensure the capacity of bed rock support layer under large diameter pile, a test-in-situ is conducted to determine the compresive strength and shear force inserting rock of the support layer, so the compresive strength and modulus value of elasticity of bed rock tested will closely tally with the actual situation.

Jan 1, 1991

By Lin Daoyi

In this paper, we have adopted the high pressure jet-grouting curtains to seal the sea-water, and to consolidate the wall of the well for deep foundation diteh, make a pladge of building and construction of deep foundation was primarily on progress without water. This paper, we have been given a test for pumping water under mainly the circumtances of sealing condition and to report in advance the capacity of seawater seeping into the gam curtains in the process of building and construction of deep foundation.

Jan 1, 1991

By James A. Schneider

The evolution of the American Petroleum Institute (API) design method for axial capacity of driven piles in siliceous sands is explored, and complemented with an overview of how changes in offshore site investigation practice have increased the level of knowledge with respect to vertical variability of soil characteristics. Increased use of the cone penetration test (CPT) provides near continuous profiles of soil type and strength which can be used in calculation methods that address variation in local shaft friction rather than the API method which seems to have initially been based on observations of average shaft friction in relatively uniform sand deposits. Development of a formulation for CPT correlations to axial pile capacity in sand is discussed, along with implications to existing factors of safety used in routine design.

Jan 1, 2006

By Michael D. Justason

This paper details the static and Statnamic load testing on a 600 mm square pre-stressed concrete pile. The pile was located at Pier 15 on the 20 million-dollar Bayou Chico Bridge Project in Pensacola, Florida. The pile was 10.5 meters long and had a design load of 1.3 MN. Three static load test cycles were performed in November, 1996. The Statnamic load test was performed in January, 1997. The Davisson Failure load of the first cycle of the static test was 3.7 MN, and the Davisson Failure load of the Statnamic test was 3.2 MN. The load-displacement curves for the two types of tests were very similar, indicating that the Statnamic load test performed well in the sandy soils. Strain gauges embedded in the pile showed 35% skin friction and 65% end bearing for both test methods. Strain gauges were located at equal spacing at five elevations in the pile. A toe accelerometer verified the rigid body assumption of the Unloading Point Method currently used in the analysis of Statnamic load tests. The data collected from the pile instrumentation was of excellent quality and represents some of the best research to date comparing static and Statnamic load tests.

Jan 1, 1997

By Trevor L. L. Orr

"AbstractThe background to the harmonization of geotechnical standards that has taken place in recent years in Europe has been the move to more economic and political integration following World War II that has led to the formation of the European Union. Prior to 2010 the standards used in the European countries for geotechnical design, investigation and testing and for the carrying out geotechnical work, such as the installation of piles, were the different national standards, which were not harmonized. The harmonization of geotechnical standards in Europe started in 1981 with work on a model Eurocode 7 for geotechnical design that led eventually to publication by CEN, the European Committee for Standardization, of the European Standard version of Eurocode 7 in 2004. In parallel with the work on Eurocode 7, a large number of associated harmonized standards have been, and are being, prepared by CEN and by the International Standards Organization (ISO) for geotechnical investigation and testing and for the execution of geotechnical works. Standards published by CEN must be adopted by the CEN member countries and all conflicting standards withdrawn. Hence all the CEN countries have adopted the same the harmonized text of Eurocode 7, but with National Annexes that allow national choice with regard to Design Approach and partial factor values. The adoption of Eurocode 7 and its associated geotechnical standards has removed the barriers to geotechnical activity in Europe due to the presence of different national standards. It has also enhanced the ability of EU firms to compete in the global market.Background to harmonization of geotechnical standards in EuropeThe initial moves towards the harmonization of geotechnical standards in Europe can be related to the economic and political developments that took place in the period immediately following World War II to revive the economies of Western Europe. Europe at that time was divided by a political and, in many places, a physical barrier, known as the Iron Curtain, into two very different and separate zones: communist in the east and non-communist in the west. In 1952 the European Coal and Steel Community (ECSC) was formed, linking 6 countries: Belgium, West Germany, France, Italy, Luxembourg and the Netherlands, and establishing a common market in coal and steel. The ECSC was the first international organization to be established on the basis of supranational principles whereby negotiated power is delegated to an authority by the governments of the member states. In 1957 the ECSC became the European Economic Community (EEC), also known as the Common Market in the English-speaking world, with the aim to bring about economic integration. With the addition of Denmark, Ireland and the UK in 1973 and Greece in 1981, followed by Portugal and Spain in 1986, this led to the formation of the European Union (EU) in 1993. East and West Germany were reunified in 1990, following the fall of the Iron Curtain in 1989. In 1995, Austria, Finland and Sweden joined the EU, and since then the numbers of countries in the EU has increased to 28, many of which are countries that were formerly behind the Iron Curtain."

Jan 1, 2014

By Dimitris Pachakis

In this paper, the authors give a brief overview of the current practice guidelines and tools for the seismic design of sheet pile quay walls, emphasizing how the design guidelines are lacking when the existing structure performance evaluation is required to meet performance-based criteria. Relying on recent experience they explain how the existing practices can be amended to focus more on performance evaluation as opposed to design. An example is given of an old sheet pile quay wall analyzed and evaluated for its performance according the recent performance criteria devised for Californian Marine Oil Terminals.

Jan 1, 2011

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By Carlos Lam, Joram M. Amir, Erez I. Amir

"Abstract The modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic loading tests on piles. This value is commonly assumed to be constant with depth though it may not be true for deep bored piles due to the chosen casting method and/or selfweight consolidation. To provide evidence to support this proposition, the results of compressive strength tests on core samples taken from four different studies have been presented. The results show a marked increase in the strength and stiffness values with depth. The results of crosshole ultrasonic tests conducted at another site also confirm the same pattern. It is therefore recommended that before load testing a pile the distribution of the E values along the pile axis should be investigated. This will ensure the use of a realistic elastic modulus value and hence the correct interpretation of thedistribution between the shaft and end resistances.IntroductionThe modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic load tests on piles. Multiplying E by the strain measured by either strain gauges (e.g. ASTM D4945) or tell-tales (e.g. Geffen and Amir, 1971) gives the stresses acting at a given pile section. Typically, in the absence of better information, the value of E is derived from laboratory tests on concrete cubes or cylinder specimens taken on site and is assumed to be constant along the pile. While this may be correct for pre-fabricated concrete piles that are cast in horizontal molds, it may not be true for cast-in-place piles that are produced in the vertical position.There are at least two factors that may contribute to the change in concrete properties with depth in a bored pile. First, the casting methods may be by free fall in dry holes (e.g. Kiefer and Baker, 1994) or by using a tremie tube if support fluids are used. In the former case, the earlier batches reach the bottom of the pile bore at a higher velocity and are thus compacted under higher energy. Second, regardless of the casting method, the fresh concrete in the pile bore will always consolidate at least partially under its own self weight. The materials in the lower parts of the pile will therefore experience a higher consolidating pressure. This can reduce the pore volume and the water content in the wet concrete, thus changing the properties of the hardened concrete. Recent research by Justs et al. (2011) has shown that even a relatively small pressure can have a significant positive effect on concrete properties such as compressive strength and stiffness. However, the possible change of concrete properties with depth is commonly ignored by foundation engineers in the current design practice."

Jan 1, 2014

By C. L. Liao

The chief experiences for constructing deep tubular columns foundation under deep water are as follows: 1. P.C. tubular columns were sunk inside the caisson. 2. P.O. tubular columns of 3.6 M. diameter were sunk thru thick soil layer to a depth of 47 M. by vibrators. 3. The double wall steel cofferdam was sunk thru soil layer to a depth 31.3 M.. 4. Bore the bedrock with rotary drill succesfully. According to the successful experiences mentioned above, the deep tubular columns foundation may be constructed beyond 100 meters.

Jan 1, 2010