Search Documents

By Mike Fabius

The Lakehead Region Conservation Authority is responsible for slopes along the Kaministiquia River, one of the largest tributaries to Lake Superior in Canada. After arresting toe erosion for a mile of riverbank, the remainder of the slope required stabilization to stop further crest regression and to protect the houses, street and services at the top. Stabilization of the 100 ft. high slope was tendered as design-build with a target safety factor of 1.3 and a design life of 75 years. The successful bid was a system of 1.4 inch diameter soil nails up to 40 feet long, installed perpendicular to the slope on a 3 to 5 foot grid. The conventional shotcrete facing was replaced with a ?green? biotechnical facing and special transverse plate heads on the nails. The key to keeping costs low proved to be installation with light equipment working on the slope, and driving the nails without drilling or grouting. Rather than tension, the design was based on bending in the nails, similar to a laterally loaded flexible pile. The paper describes the design and installation of this innovative system. The design is discussed in terms of soil properties, nail resistance as it varies with depth, failure modes, corrosion protection, root design and nail head design. Construction challenges are discussed. The system is compared to an adjacent anchored soldier pile wall built along the same slope 20 years ago. Post construction monitoring results confirm predicted performance.

Jan 1, 2006

By Dan Brown

Two drilled shaft foundations were subjected to axial load tests in order to measure the influence of drilling fluid on performance. Other than the differing drilling fluids, the shafts were constructed with great care to ensure identical conditions. The results indicate superior performance in both side shear and base resistance of the shaft constructed using a polymer over that of the shaft constructed using bentonite drilling slurry.

Jan 1, 2002

By Fritz J. Klingler

From site demolition, to design, to construction, Detroit's new Tiger Stadium project is required to be completed within a short 2 ½ years from award of the design-build contract. Such extreme schedule requirements together with somewhat difficult ground conditions at the site, resulted in several challenges in the design and construction of the deep foundation system for the stadium. During the geotechnical investigation, an intermittent water bearing sand layer was encountered overlying the hardpan at the site. As a result, some concern developed regarding the potential for collapse of caisson bells within this layer, as well as the potential for flooding of the caissons during drilling. Although sand and/or ground water was encountered within about half of the caissons, standard drilling and belling methods were used, and adverse conditions were controlled in almost all cases through expeditious drilling, inspection and concreting of the caissons. This paper will present a summary of the ground conditions, design and specification requirements, and construction methods used to successfully install the caissons for this project.

Jan 1, 1999

By Lu Peiyan

A computation model of soil-pile (wall) interaction under lateral loading is presented in this paper. The model has been applied to some engineering projects, and the comparison between computation result and measured result shows good agreement, so the model is proved to be correct and practical.

Jan 1, 1991

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By Jiwei Duan

The energy transferred from a hammer to the pile top is considered as the effective energy in this paper. The effective energy is related to the pile dimensions, soil and pile-soil interface properties. This relation may be expressed as an equation based on the dimensionless theory. The relationship between pile capacity and effective energy was studied by performing a series of wave equation analyses using a commercial software called GRLWEAP (Wave Equation Analysis Program) by GRL Engineers, Inc. The results show that the pile capacity increases with the blow count when the effective energy is constant, however, it has a little change as the blow count is over 100 blows per foot. The pile capacity decreases as the ratio of pile penetration depth to pile diameter increases if the effective energy is constant. The pile capacity will increase as the pile diameter and wall thickness increases if the effective energy is constant. The pile stickout (pile length above the ground surface) does not have a significant effect on the effective energy and may be neglected. Curves for pile capacity versus effective energy are presented to be used for preliminary hammer selection according to effective energy and hammer efficiency. Finally, a case from PDA testing was studied. Measurements of the effective energy and pile capacity by CAPWAP were presented and compared with the results by GRLWEAP.

Jan 1, 2006

By Joseph C. Gillen

This paper discusses the design, construction, and performance of the support of excavation system used at The Atlantic Building jobsite. The support of excavation system had to be adaptable to the different conditions surrounding the site. These conditions included support of four historic building façades, including the nine-story Atlantic Building, as well as support of three historic row-houses along two walls. Directly adjacent to the site is the historic Ford?s Theatre and townhouse. Across a 15? alley is the American Immigration Lawyers Association (AILA) Building, and across a 30? alley is the Federal Election Commission Building and another ongoing excavation. Of historical note, these two alleys were the escape route for John Wilkes Booth following his assassination of President Lincoln. With the excavation being 53? to 58? deep, the system included driven and drilled soldier piles, drilled bracket piles, and two modified tangent walls. The bracing included tiebacks, corner braces, wales, cross lot struts, and a specially designed support system for the nine-story façade. The footprint of the excavation included 12 corners and all alleys and streets were to remain open during construction. The performance requirements for system movement at Ford?s Theatre and AILA Building were ½ inches in the horizontal direction. The modified tangent walls were used in these areas to provide stiffness. The soil conditions at the site were fill material on top of a shallow, sandy, silty, gravel layer on top of a deep layer of soft organic silt and clay. Below the silt and clay layer was fine sandy material at the subgrade.

Jan 1, 2006

By W. J. Grose

The Embankment Place office development over the platforms of Charing Cross Railway Station in London has presented many interesting and unusual problems to the engineers involved with the project. The main structure is supported on widely-spaced columns which penetrate the station platforms and underlying vaults, calling for high capacity foundations built in severely restricted spaces. Hand-dug underreamed piles were chosen. Whilst a conventional design approach was taken to size the piles, a detailed appraisal of ground movements was made to explore the effects of the new building loads on the existing foundations, not only beyond the site perimeter but also those amongst the new foundations. Before construction of the pile proper could take place, it was necessary to sink a caisson through the upper unstable and water-bearing soils. This being identified as a high-risk item, a full-scale trial was carried out prior to embarking on the main works. The twenty-one hand-dug piles were 2.5m diameter, over 30m deep and belled out to between 4.5m and 6.6m.

Jan 1, 1989

By Basem Sh. Hazzan

In the last four decades significant effort has been devoted to designing piles in expansive clay soils. Nevertheless, only a scant effort has been devoted to the elimination of heave forces acting on the upper part of lightly loaded piles. For this purpose, an investigation site was established in Karmiel in Northern Israel. On this site sixteen unloaded cast-in-situ piles, both uncoated and coated, were installed in a moderately expansive clay soil in the end of summer 1996. The piles were executed to different depths ranging between 2m and 7m and were observed over a period of 27 months. Another nine unloaded cast-in-situ bored piles were installed at the end of summer 1998 for carrying out pullout tests. These piles were embedded two meters from the ground surface. Results obtained from observations and from full-scale static pull out tests showed that separating the piles from the surrounding clay in the active zone by a twin walled sleeve eliminated the heave forces significantly. The scope of the work is, determining of the elimination degree of the heave forces due to the provision of the above sleeve.

Jan 1, 1999

By Feng Yongxuan

Anchored sheep pile is normally used in deep excavations, many of which only require stability in accordance with Terzaghi theory. In this paper, based on the experience, new lateral earth pressure method is adopted taking account into interaction among soil, anchors and sheet piles so that a group for the project under very difficult conditions and very severe requirments, especially, for the displacements are determined according to that mentioned above. During and after construction, displacements monitoring were carried out for about four months, which was proved that there was a little difference between calculation and practice.

Jan 1, 1991

By Howard A. Perko

Soldier pile and lagging is a conventional means of temporary excavation shoring. Timber lagging design has traditionally been based upon the designer's experience or empirical rules. One such method is the Goldberg Zoino chart used by the Federal Highway Administration. Most of these methods restrict the designer to a consistent soil profile, certain pile spacing, construction grade timber lagging, and limited depth. The methods do not take into account surcharge loads or a variety of other factors that could arise. A designer working outside of ordinary circumstances with unusual loads, varying soil conditions, or alternate lagging materials has difficulty estimating lateral earth pressures. In rigid earth retention systems, lateral earth pressure is generally assumed to be constant along the length of the wall. In soldier pile and lagging systems, the lagging is often considerably less stiff than the steel soldier piles. As the lagging deflects, the soil tends to bridge between the stiffer elements resulting in a lower pressure on the lagging. Several previously published methods by others for determining this reduced pressure are summarized and discussed. These methods typically consist of using a portion of the active earth pressure in several different pressure distributions. A simple theoretical model is presented for determination of lateral earth pressures on wood lagging. The model is based on a three-dimensional "silo" shaped sliding wedge analysis. Results of the model are compared with other published methods. The model compares well with these methods which cover the normal spectrum of design situations. In addition, the model can be used to estimate lateral earth pressures outside typical situations.

Jan 1, 2008

By Mauricio Terceros, Martin Achmus, Freddy Lopez

The massive use of deep foundations had a remarkable influence in the building industry in the 20th century. Piles and micropiles made possible to erect thousands of civil structures around the world, changing quintessentially the urban and rural landscapes. Especially in urban areas, the ongoing development requires not only new infrastructure, but also to increase the capacity and/or to extend the serviceability of existing structures (buildings, bridges, etc.). Factors such as the change of use of existing facilities or the requirement to comply with updated building regulations confront Civil Engineers with the question, whether to tear down and build new structures, or to reinforce the existing structures from their foundations. Micropiling has enabled designers to come up with technical feasible solutions to retrofit the existing deep foundations, making the structural reinforcement a real option, even under considerable changes in the loading conditions. The following article presents an overview of an intervention project, where micropiles were designed to reinforce the original pile foundation of an existing building, enabling it to be reused with a different structural function. This paper will focus mainly on the analysis of the interaction between the existing piles and the reinforcing micropiles, especially in terms of settlements’ compatibility. Finally, the adopted solution, with its correspondent design considerations and execution process will be presented.

Jan 1, 2018

By Magnus Ruin

The dry deep mixing method for stabilization of soft soil has been used in the Scandinavian countries for 25 years. The typical application has been stabilization of soft inorganic clay. Today the method is used more frequently in organic soil with good results. The Limix System, introduced in the USA by Hercules Grundläggning AB and TREVIICOS Corporation, is a cost-effective dry deep mixing method used to stabilize most types of soft soil. This paper presents the general principles of stabilizing organic soil with the dry mix method and two case histories of soil stabilization projects in organic soil. Between October 2000 and June 2001 the Limix System was used in England to stabilize soft organic alluvium at the Channel Tunnel Rail Link, Contract 440. During year 2000 the Limix System was used in soft organic soil in Holland near the Groene Hart Tunnel entrance to support trench excavations for slurry walls and concrete barrettes.

Jan 1, 2001

By A. B. Desai

The construction of 1144 nos. of piles, each 1.5 m diameter, bored-cast-in-situ type and varying in depths from 6.5 to 23m, has been completed as foundation for 26 piers of 548 m long aqueduct across Orsang river to carry 1128 m3 water of Narmada Main Canal of the Sardar Sarovar Project in Gujarat. These piles are socketed 1.5 m into foundation grade rockmass. The portal system of 44 nos. of piles and pile cap at the top for each pier is analyzed considering the portal fixed at bottom of piles. The borings for pile shaft were done deploying reverse mud circulation rigs and also by conventional chiseling and bailing operations. Besides vertical loading tests and lateral loading test on piles, dynamic tests such as low strain integrity testing on 290 piles and high strain pile testing on 17 piles were also conducted. The results indicated that (a) the settlement/ displacement are much less than the prescribed limits (b) good quality of concrete (c) piles are firmly socketed and (d) piles have adequate structural capacity to withstand the design load.

Jan 1, 1996

By Benoit Virollet

Over the last 10 years the diameter of unbraced, unlined and unanchored circular shafts has grown dramatically in many parts of the world. This progress has taken place through improvements in: construction methods; concrete rheology; and design capabilities. Excavation equipment has become more precise in terms of operator control and ability to correct alignment of digging elements leading to better alignment tolerances. Also contributing to the increases in shaft diameters is the evolution of design models. A better understanding of soil structure interaction is being incorporated into the analyses in terms of radial soil stresses and imposed loads on the shaft. This paper provides an overview of the recent progress made in circular shaft construction, the primary design considerations, and some innovative uses of efficient arc elements to develop unsupported structures of other shapes. In addition, a summary of recent circular shafts constructed worldwide is provided.

Jan 1, 2006

By Seth L. Pearlman

Pin Piles are small diameter high capacity drilled and grouted piles also called minipiles or micropiles. They are ideal for building foundations on sites with poor ground conditions, sensitive surroundings, restricted vertical clearance, or difficult access. They are also well suited to foundation underpinning, arresting ground movements, and increasing the capacity of existing foundations. The major factors for selection of Pin Piles are reviewed; drilling, grouting, and design fundamentals are summarized; and a major case history is presented for the underpinning of the 43 story elevator core at the recently opened Mandalay Bay Resort and Casino in Las Vegas, NV.

Jan 1, 2000

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987