Search Documents

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shaft (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, including the post-grouting of all drilled shaft tips. ? Design and construction of the scour protection for the two main pylons, ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2013

By Jr. D'Angelo, Michael M. Blendy, Shawn Downey

"A grouted helical pile was used to support new buildings in the reconstruction of a large residential development. Foundation options were complicated by urban fill underlain with variable alluvial soil. A driven timber pile and grade beam system was recommended to support the new buildings. Other foundation options are also discussed. The grouted helical pile was quoted as an alternate and ultimately won the bid based on the economics and performance of the system. Data from 8 load tests was used to develop an empirical site specific relationship for determining pile capacity based on both installing torque and installation depth. Design to incorporate tolerance on installed pile location is presented. With the three phases completed, 554 residential dwelling units supported by 3645 grouted helical piles had been constructed covering 18 city blocks on the 44 acre site. IntroductionThe Philadelphia Housing Authority reconstructed the Tasker Homes housing complex located in southern Philadelphia, Pennsylvania, adjacent to the Schuylkill Expressway in the Grays Ferry area. Keating Building Corp. and Pennoni Associates were the general contractor and the structural engineer respectively. The original Tasker Homes development was constructed from 1940 to 1941 and consisted of 44 acres of primarily two and three-story residential brick buildings. These buildings were supported by a timber pile foundation system. The structural condition of the buildings supported on the timber piles was generally good in comparison to areas outside the buildings. These areas had settled possibly up to 2-feet in places due to the heterogeneous nature of the urban fill."

Jan 1, 2005

By Rajesh A. Vaidya

A large scale piling work is undertaken in India for an important fast track industrial project. Thousands of solid square precast concrete piles are driven to depths of around 50m. Soils encountered are of alluvial origin with very soft clays varying in thickness from 10 to 18m at the top followed by medium dense to dense and occasionally very dense sand, stiff clay and finally dense to very dense sand layer as the founding layer. Recent site grading with around 4 metres thick hydraulically filled river sand necessitated driving the piles to the bottom sand layer to avoid problems on account of negative skin friction and to achieve optimum pile capacity. A process approach suggested by Bell et al (2002) to promote better understanding of the pile behaviour, pile capacity, and parameters assumed at design stage for static capacity and for wave equation analysis is followed with an aim to bring in effective economy in terms of pile length and pile installation speed. Soil investigation work is also undertaken in stages to cut down pile wastage. A judicious combination of PDA and static pile load tests is followed. Pile Driving Analyser (PDA) tests at end of driving and also at various stages of recovery of pile capacity are carried out to understand the pore pressure dissipation phenomenon. The paper attempts to present some of the valuable experiences that would go to establish precast pile as a very effective alternative to driven cast-in-situ piles and bored piles which are very common in this part of the world despite their limitations in terms of economy, speed and certain geotechnical aspects.

Jan 1, 2007

By Bernhard Bruggaier

Outside the oil and gas industry there is an increasing demand to install big piles for the foundation of ports, bridges, and wind-energy plants. This article introduces the design and techniques in using large MENCK pile driving hammers to install big foundation piles. Piles with a length up to 120 m, an outside diameter of 1.0 m to 3.15 m and weighing between 25t and 400t are being driven for these types of foundations. The required energy lies between 200 and 1700 kNm. Pile driving hammers that bring this amount of energy weigh from 38 to 300t and have a length between 10 and 20 m. Handling these big pile driving hammers requires a crawler crane on land or cranes on floating pontoons or jack-ups when working in water. Possible are either vertical or inclined piles, using a leader for inclinations up to 1:1.7 or up to 1:3 in a free riding version. Project descriptions demonstrate the versatility and practical use of the equipment under diverse operating conditions.

Jan 1, 2002

By Gary L. Seider

Chance, a Division of Hubbell Power Systems, Inc., in conjunction with Sailors Engineering, Inc. has updated its Helical Design Capacity Software. This latest version, ?HeliCAP® v2.0?, is a state-of-the-art helical anchor and pile capacity program designed to operate in the Microsoft® environment. The program calculates the tension and compression capacity along with the frictional capacity, if applicable, of CHANCE® Civil Construction helical anchors and piles using design theories and methods adopted by Chance. This paper details the current state of practice employed by the software in the design methods and installation methodologies of helical anchors and piles.

Jan 1, 2007

By Alexandra Weidle, Seffen Leppla, Rolf Katzenbach, Matthias Seip

"A lot of different deep mixing systems have been developed in the last decades for a wide spectrum of applications, e.g. retaining and foundations systems, soil improvement, sealing of toxic substances or dyke strengthening. The paper will deal with special aspects of constructions with deep mixing systems for infrastructures like soil improvement for cyclic loadings and underpinnings in difficult soil conditions by presenting cases from engineering practice.1. DEEP DRY SOIL MIXING FOR SOIL IMPROVEMENT OF RAILWAY TRACKS IN VERY SOFT SOILS1.1 IntroductionRailway tracks are set into vibrations by train passing. In very soft soil this leads to long-term deformations which lead to speed limits, temporary closings and big maintenance efforts. The energy of the dynamic loading is transmitted into the soil by compression and shear waves and at the surface by rayleigh waves (Wood 1968). The expansion of the waves are influenced by•,thickness of the soft soil layer•,density of the soft soil layer•,stiffness of the soft soil layer•,saturation of the soft soil layer•,frequency of the dynamic loadingThe frequency of the dynamic loading depends on the train velocity and the distance of the wheels and wheel sets. If the frequency of the dynamic loading is in the range of the natural frequency of the soft soil layer the vibrations increase extremely (Lieberenz et al. 2003). As a result the long-term deformations will increase as well.To avoid these long-term deformations and the resulting operation restrictions and maintenance efforts an adequate soil improvement is necessary. For the optimization of the soil improvement field tests have been carried out.1.2 Experimental field testsThe field tests have been carried out at a 300 m long test track with five different setups, each 30 m long:•,test track TS 0: no soil improvement•,test track TS 1: soil improvement with single lime-cement-columns 5.9 m deep (Figure 1a)•,test track TS 2: soil improvement with single lime-cement-columns 5.9 m and 10.4 m deep (Figure 1b)"

Jan 1, 2015

By William Auyeung

Micro-piles are small-diameter, drilled and grouted reinforced piles used for both structural support and in situ earth reinforcement. They were conceived in Italy in 1952, but have become popular in Canada and the United State only since the mid-1980s. The Province of British Columbia completed a construction of a 265-km (165 miles) four-lane highway between Campbell River and Victoria in the year of 2000. The construction of Big Qualicum Bridge was part of the above mentioned provincial government project and this bridge was made of twin cast-in-place concrete parabolic arch structures. The overall length of the bridge is 261 metres (856 feet) and the width is 24.2 metres (80 feet). The massive thrust from each arch is resisted by groups of 46 drilled micro-piles that are about 230 mm (9 inches) in diameter with No. 18 high strength Dywidag threaded bars with double corrosion protection up to 15 metres (50 feet) long. This paper will describe the micro-pile design and installation methods. The performance of the micro-piles in full scale testing in tension and compression monitored with electronic strain gauges will be presented. The impact of drilling methods on the performance of the micro-piles will also be discussed.

Jan 1, 2004

By William M. Camp

Construction-induced earthborn vibrations have long been recognized as a potential problem with respect to the constructed environment and various vibration criteria are in use to prevent damage. A special case of construction vibration control is the protection of early-age or ?green? concrete. Unlike limits for damage prevention to building stock, there is no rational, widely accepted limit for protection of early-age concrete. Numerous criteria have been proposed or reported in the literature and the most relevant and rational proposals are summarized herein. These findings are applied to a case history involving both bored and driven piles. Vibration measurements were made during pile driving activities and the vibration magnitude was evaluated with respect to the exposure of freshly-placed and curing concrete to the earthborn vibrations. The maximum vibration magnitude at the applicable distances from pile driving was on the order of 0.3 inches per second. Based on the most persuasive literature, threshold values of 0.8 inches per second or even 1 to 2 inches per second for the protection of green concrete appear to be well-supported. Consequently, it was concluded that the pile driving activities and bored pile construction could proceed simultaneously.

Jan 1, 2010

By Kozo Takeda, Arashi Shimano

"Dry Jet Mixing (DJM) technique is widely known as soil mitigation technique with small ground displacement during installation comparing with other techniques. Some projects involving sensitive structures, however, require smaller impact than in conventional technique. In order to reduce ground displacement during DJM installation, this paper introduces systematic mixing technique, RD-DJM (Reducing Displacement – Dry Jet Mixing). RD-DJM is characterized by injection nozzle on the rim of mixing blade and fin plate on mixing shaft. These devices contribute efficient collection of injected air toward mixing shaft and result in reduction of ground displacement. The authors demonstrate successful performance of RD-DJM indicating difference between conventional installation and RD-DJM technique.INTRODUCTIONThe Dry Jet Mixing (DJM) method is one of the most common techniques in Japanese deep soil mixing field and characterized mechanical mixing of powdery binder with in-situ ground (dry-mixing technique). It is widely believed that DJM Method has great advantages in less quantity of binder to achieve the desired strength and less waste generation during installation.DJM method can meet the required strength with less binder content than wet mixing. And volume of binder of dry mixing is absolutely less than wet-mixing injecting considerable volume of binder slurry. This means that dry mixing causes less ground displacement compared with wet mixing.As the medium for forced feeding of the binder, the DJM method uses compressed air, which is blown from the mixing blade nozzles to scatter the binder and then recovered through the periphery of the mixing shaft to the ground surface. Because the binder is injected outward from the injection orifice at the root of the mixing shaft, a part of the air may escape to untreated areas due to the blockage of air recovery path around the mixing shaft. Figure 1 illustrates possible escaped air and leakage around installation location."

Jan 1, 2015

By Robert S. Thomas, Bernard M. Tarralle, Nasser Massoudi

"The Commonwealth of Virginia is restoring and expanding its Capitol of great historic significance. Designed by Thomas Jefferson in 1785, it is the second oldest Capitol building in the United States. The building expansion required excavations immediately adjacent to its South Portico. The building, which rests on shallow brick footings, is very sensitive to any disturbance caused by construction and excavation. A comprehensive and secure plan of operations was devised by the design team to ensure that this national monument remains unharmed by the new construction. Various construction techniques were implemented to satisfy the strict movement goal of 0.25 inch and distortion of U2000. They consisted of jet grout columns to stabilize the upper soils, compensation grouting for future foundation leveling, a tied-back reinforced concrete diaphragm wall for excavation retention and foundations, and realtime instrumentation for monitoring. This paper describes the design approach for the retention system, providing information on the various construction phases and techn iques, and reports on the movements recorded by the real-time monitoring system during the course of the project. At the time of this manuscript preparation, and the deep excavation complete to final grade, the results indicate that the extremely restrictive building movement criteria have been met. The success can be credited to detailed design, close cooperation among the project team, prudent construction methods, and real-time monitoring. INTRODUCTIONThe Commonwealth of Virginia is undertaking a comprehensive renovation and expansion of the Virginia Capitol building located in Richmond, Virginia. The Capitol building was designed by Thomas Jefferson in 1785, with construction of the original building starting the same year. The Capitol building was designated a National Historic Landmark in 1960 and was listed on the National Register of Historic Places in 1966.A part of the comprehensive renovation and expansion of the Capitol is a 25,000-square foot, two-level subterranean extension on the south side of the Capitol building, which will serve as a new Visitor Center and public entrance for the Capitol. Deep excavations were required for the construction of the new Visitor Center. The excavation required a permanent retention system to accommodate an approximately 40- foot deep excavation."

Jan 1, 2005

By Adel M. Hanna, Ibrahim M. Mashhour

"Collapsible soil is known as one of the difficult soils, which possesses considerable strength when it is dry and significantly reduced when inundated. In practice, in case of a thick layer, pile foundations are often used to penetrate the collapsible soil to firm soil/rock strata. Inundation of collapsible soil is accompanied by a large and sudden settlement, which may significantly increase the negative skin friction and accordingly the drag loads on the pile’s shaft. Inundation may take place from the running surface-water or raising the groundwater. In case of surface water, the amount of settlement varies, depending on the extent of the wetted zone and the degree of saturation in the soil, while rising groundwater will produce full saturation in the ground and accordingly larger settlement.In the literature, there is lack of reports dealing with the prediction of the drag load on piles in collapsible soils subjected to inundation. This is due to the complexity of modeling collapsible soil analytically. Alternatively; the results of a sophisticated experimental investigation may guide the researcher to develop a model to predict the drag load on these piles.This paper presents the results of a small-scale experimental investigation tailored to measure the soil collapse during inundation and the associated drag load on an endbearing pile’s shaft. Based on the results of the present investigation, the effect of the soil collapse potential and the pressure acting on the soil during inundation on negative skin friction is presented.INTRODUCTIONCollapsible soil is a metastable material, traditionally defined as unsaturated soils that experiences a radical rearrangement of particles and significant reduction of volume upon wetting with or without loading (Bara 1976; Houston et al., 1988). A wide range of soils fall into the category of collapsible soil, including naturally existing types of soils such as: Alluvial flood plains, mud flows, residual soils, colluvial deposits, fans, aeolian or wind-blow deposits sands and silts (loess), volcanic tuffs, gypsum, dispersive clays, loose cemented sands , sodium rich montmorillonite clays (Clemence and Finbarr 1981).Soil wetting and soil saturation may take place as a result of urbanization or natural causes, such as: groundwater level rise, landscape irrigation, broken water pipelines or sewer lines, poor surface drainage, groundwater recharge, cut/fill construction, and moisture increase due to capillary rise. The severity of the outcome depends heavily on the so called collapse potential of the soil, which depends mainly on; soil type, compaction effort, initial water content and stress level at soaking (Houston and Houston, 1997; Ayadat and Hanna, 2007)."

Jan 1, 2015

By Aditi Sharma, Sumanta Haldar

Scouring of soil is the major concern forthe various hydraulic structures built in the flowing rivers since scouring impacts the bearing capacity of foundations. Hence, consideration of scouring in the design of foundations for hydraulic structures is crucial. Pile groups in bridges are subjected to combined vertical and horizontal loading due to self-weight, live loads, vehicular impacts, wind load, earth pressure, and current. Hence, an assessment of the combined bearing capacity of pile groups subjected to scour is essential for the safety of the structure. This paper aims to analyze the bearing capacity of pile group supporting the bridge under combined loading i.e., Vertical (V) and Horizontal (H) loading subjected to local scour. Three-dimensional finite element model (3D-FEM) of a 3 x 3 pile group embedded in homogeneous sandy soil is established in Abaqus (2018). Mohr-Coulomb plasticity model is used for the soil domain. The pile group is modelled as linear elastic. Finally, V-H yield envelopes are obtained with and without scour. The potential impact of different parameters, such as angle of attack, flow velocity, depth of flow, and different pile length-to-diameter ratios (L/D) and spacing-to-diameter ratios (S/D) of pile group on V-H yield envelopes is studied.

Sep 1, 2022

By Kenneth M. Berrry

A unique situation has developed at an abandoned coal mine in St. Clair County, Illinois. Subsidence features have been observed at the ground surface over the mine including settlement of a pair of bridges for Illinois Route 158. The Illinois Department of Transportation (IDOT) is currently replacing the two bridges. Foundation treatment for the two new bridges included backfilling the mine void. The light rail system for St Louis (MetroLink) is also constructing a bridge over the same abandoned coal mine less than 1000 ft from the Route 158 bridges. The new MetroLink bridge is being constructed using piles which extend through the coal mine and overlying bedrock in order to transfer the loads to below the mine floor. The differing foundation types for the IDOT and MetroLink bridges were due to geometry and economic factors involved with the individual structures.

Jan 1, 2001

By Todd W. Armstrong, Michael D. Reader

"INTRODUCTIONThe Playa Vista Development is the largest urban infill development in the history of the United States. Overall, it encompasses about 1100 acres in the City of Los Angeles and is situated north of Los Angeles International Airport near the Pacific Ocean. The development taking place on the project consists primarily of high-density residential condominiums with 1 to 2 levels of subterranean parking . The geotechnical conditions are typified by high groundwater, soft clays, and liquefaction, in addition to environmental issues such as methane.Due to a combination of the geotechnical factors and noise restrictions, both driven and drilled piles were not feasible once the initial phase of the project was occupied. As a result, the project developer undertook a testing program that consisted of the installation and load testing of 9 piles in order to obtain City of Los Angeles acceptance of a pile installation system that met the site constraints. The testing program was divided between two separate contractors operating on sites set on opposite sides on the street (Figure 1 ). Contractors working in Test Areas A & B employed the ""dry dip"" and ""wet dip"" methods of auger pressure grouted displacement (APGD) pile installation, respectively.This paper summarizes the extraordinary program undertaken to install, document, test, and examine auger pressure grouted displacement piles at this site. The program ultimately resulted in City acceptance of auger pressure grouted displacement piles, a historically difficult challenge given the City's resistance of acceptance of ""new"" technologies.A summary of elements included in the test program are: (1) quality control; (2) load testing; (3) long-term testing; (4) non-destructive testing; and (5) pile exhumation."

Jan 1, 2005

By W. Morgan NeSmith

Drilled displacement (DD) piles often develop significantly larger unit shaft resistance values than other drilled or augered pile systems in coarse grained materials. Minimal vibration and limited spoil development are also associated with DD pile installation and these factors are frequently additional financial and/or environmental benefits of the system. The application of DD piles in North America dates to the mid-1990s and their use in the Midwestern United States has been significant, particularly in the past 10 years. The authors have collected an extensive database of DD pile performance in the United States. The alluvial and glacial deposits of the Midwestern U.S. provide conditions where drilled displacement piles perform very efficiently when compared to coastal and residual geologies. This paper presents a summary of the authors? experience regarding installation and performance of DD piles in the Midwestern U.S. Information presented includes summary presentations of DD performance across a range of site conditions as well as a discussion of the relationship of DD performance and installation effort in the Midwest as compared to other geologic settings in the U.S.

Jan 1, 2009

By A. Felipe Uribe-Henao, Camilo Ballesteros, Luis G. Arboleda-Monsalve, David G. Zapata-Medina

Conventional excavation analysis based on total or effective stress methods can result in inaccurate estimation of ground movements when impervious soil conditions or rapid excavation sequences are not found in the excavation (i.e., assumption of undrained response is not valid). The influence of excavation rate, hydraulic conductivity, and excavation geometry on the fully coupled solid-fluid behavior of a braced excavation in cohesive soils are studied parametrically using PLAXIS2D. The coupled excavation analysis is performed using the Hypoplasticity clay model to reproduce the constitutive behavior of soil and the poro-elasticity Biot’s theory to account for changes in pore water pressure due to deformations in the soil skeleton. Results obtained from the parametric studies indicate that excavation rates to hydraulic conductivity ratios, ER/k, smaller than 0.1 and larger than 104 can be used as limits for drained and undrained analyses, respectively. In practical applications, undrained and partially drained excavation analysis with ER/k larger than 102 resulted in a similar ground deformation. However, smaller ER/k ratios demand fully coupled solid-fluid analysis. An analytical method aimed at predicting excess pore water pressures and determining the required type of analysis associated with soil and excavation conditions, e.g., drained, partially drained, and undrained analysis, is proposed herein to accurately estimate the ground movements induced by the excavation.

By Tony Amis

There is very limited information relating to the potential impact of temperature cycles, outside the variation that occurs naturally, on the behaviour of foundation piles. Such thermal loading occurs when piles are used as heat exchange elements within a Ground Sourced Heat Pump system, in addition to carrying building loads to competent strata. An investigation has been undertaken where a conventional load test has been extended to include a period in which the load is maintained and temperature cycles applied. Instrumentation was installed in the test pile, an adjacent borehole, two of the anchor piles and the heat sink pile in order to be able to develop an understanding of the temperature variation and associated strain changes within and between the various elements. Conventional electronic strain and temperature gauges have been used in conjunction with optical fibre sensors which also measure strain and temperature changes. The results have confirmed the validity of the assumption made in the thermo-dynamic design of the system, the compatibility of the differing measurement systems and differing installation methods for the optical fibres, and initial assessment suggests that the load-settlement response of the pile is not adversely affected by the temperature cycles applied.

Jan 1, 2008

By Abolfazl Eslami, Fatemeh Rostami, Sara Heidarie Golafzani, Mohammad Arabameri

Collapsible loess is classified as problematic soil found in most continents. The loess immediately collapses under stresses induced by axial compressive loading or the soil weight when exposed to moisture. In Iran, vast areas of the Golestan province are covered with aeolian loess deposits. This paper investigates whether the simultaneous effect of inundation and pre-loading in helical pile installation are operative and effective in improvement of Golestan loess. The effect of installation conditions on loess collapsibility is studied via two main approaches, i.e., field investigations and physical modelling. The experimental studies include installation of eight single helix piles in the Amirkabir University of Technology Frustum Confining Vessel, i.e., FCV-AUT. Also, four single helix piles with embedment depth of 3 m and diameter of 250 mm were installed in Golestan province and full-scale pile static loading tests were performed. The results indicated that the simultaneous application of crowd loading and water pressure during installation of helical piles results in better soil shear strength parameters. Moreover, high crowd stresses or low crowd stresses accompanied by water pressure during pile installation brings about similar load-displacement behavior of model piles installed in FCV-AUT and full-scale helical piles.

Oct 1, 2022

By Mohamed Hassan, Matthias Seip, Steffen Leppla

In the east of Frankfurt am Main, Germany, a new high-rise building is planned directly next to the river Main. The high-rise building will have a height of about 75 m and will be founded on a Combined Pile-Raft Foundation (CPRF) in the tertiary marl. The new structure will be constructed next to important, sensitive traffic infrastructure. The foundation of the new high-rise building adjoins directly existing historic quay structures, which are more than 100 years old. For analysis of the stability and the serviceability of the heavily eccentric loaded foundation of the new high-rise building and the existing structures and for the investigation of the soil-structure interaction complex three dimensional, non-linear numerical simulations have been carried out. These numerical simulations take into account all geometric and material specific boundary conditions, including the history of the construction of the whole area. The paper introduces into a very complex construction project in which the investigation of the soil-structure interaction has an important role. The three-dimensional numerical simulations are explained and the results are shown.

May 1, 2022

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 fUsec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases. and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

May 11, 2007