Search Documents

By David R. Black

Foundation problems due to collapsible and expansive soils are well known throughout the arid western United States. Millions of dollars are spent annually to counteract the effects of such soils for both new foundations and existing foundations suffering from settlement or heave. Over the last 20 years helical screw piles have come into wide-spread use as a permanent deep foundation element for these problem soils, especially in the arid western United States where, in some areas, they are a standard of practice. Independent research resulting in recognition by every national building code in the United States has legitimized helical screw pile technology. Once thought of in terms of light structural underpinning, helical screw piles of today are designed to take heavy structural loads, vertical and lateral, tension or compression, including seismic loads. With proper pile grouping, design capacities for column loads over 4,500 kN (1,000 kips) are attainable. This paper discusses design considerations specifically dealing with collapsible and expansive soils: soil investigation parameters, predicted settlement and long-term creep, heave in expansive soils, downdrag in collapsible soils, shaft slenderness buckling, maintaining shaft alignment during installation, refusal condition, water migration along the shaft, lateral loading, cyclical loading for seismic loads and machine foundations, corrosion, helix durability during installation, the installation torque vs. capacity equation, and design methodology. The paper concludes with several case histories where helical screw piles were used for new structural foundations and to underpin existing failed foundations in St. George, Utah, Cedar City, Utah, and Denver, Colorado, USA, sites of some of the most expansive clay and collapsible soil in North America. Soil descriptions and performance histories are presented.

Jan 1, 2002

By Edwin W. Hickey

This paper briefly discusses the geologic conditions in South Florida relative to the design, construction, and performance of deep foundations. The subsurface conditions in this area are unique in that the rock layers are highly porous and often very soft, and are sandwiched between layers of typically loose, uncemented quartz fine sands. Due to the high porosity of the Miami Limestone, 4-inch diameter rock coring is often required to obtain intact samples, and dewatering of excavations is sometimes difficult or impossible. The sand layers, typically tens of feet thick, are very loose to loose in relative density and have been the cause of unexpected large, deep foundation settlements. The engineering properties of the various geologic formations are discussed, along with typical deep foundation types used in the Miami area prior to and after 1980.

Jan 1, 2003

By Daiki Takano, Naoki Takahashi, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"The method in this study, in which cement-treated piles are installed into the ground to decrease the amount of liquefied lateral flow, has been studied. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. In their investigation, they propose shifting the position of the piles to prevent lateral flow in various directions. The present study conducted centrifuge model tests to clarify the improvement effect of piles against the lateral flow of liquefied soil and the effect of the pile arrangement. Then, numerical fluid analyses were conducted to consider the improvement mechanism. As a result, the model tests and numerical analyses showed that the pile improvement dramatically reduced the lateral displacement and that the average total flow velocity decreased in the irregular case.INTRODUCTIONLiquefied ground subjected to seismic motion loses its stiffness and strength, and lateral flow often occurs in sloping areas and backfill areas behind collapsed quay walls. In the Hyogoken–Nanbu Earthquake in 1995, the reclaimed island that was surrounded by collapsed quay walls expanded toward the sea and the amount of displacement reached a few metres (Hamada et al., 1996). Two countermeasures can be considered to guard against lateral flow: preventing liquefaction and reducing lateral displacement. The former method is ideal; however it is costly and time-consuming. Based on these considerations, the authors (Takahashi et al., 2013; Morikawa et al., 2014) are currently studying a method in which cement-treated piles are installed into the ground (see Fig. 1) to decrease the amount of liquefied lateral flow. The countermeasure cost using this method is relatively low because of the low replacement ratio. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. It has been proposed that the position of the piles should be shifted so that lateral flow can be prevented in various directions, as described in Fig. 2."

Jan 1, 2015

By Andrew Cushing

This paper presents the design and construction of the foundation for a major high-rise real estate development on the west side of Manhattan. Arup was retained by Underpinning and Foundation Skanska to design a secant pile wall as excavation support for a proposed two-level basement of a new 23-story residential building located at 100 11th Avenue and West 19th Street. The secant pile wall will also act as the permanent basement retaining wall for the new building. The site is bounded on two sides by existing structures and is underlain by a thick deposit of very soft organic silt and clay. Therefore, the potential for ground movements and their impact on an adjacent structure bearing on shallow footings were of the utmost concern. This paper addresses the design and construction considerations associated with this secant wall, as well as installation details. Measured wall movements are also used to assess the validity of the pre-construction soil strength and stiffness design parameters.

Jan 1, 2008

By Wolfram Groh

New underground floors comprising the complete footprint area of the building structure, were constructed under an existing building in sand, located in the Verdun district of Beirut / Lebanon. The works for the rehabilitation and extension of the Verdun 528 building were carried out between December 1999 and August 2000. A restriction of differential vertical movement of existing load bearing walls and columns had to be respected throughout the construction phase of the new basements. Support measures for the building were taken based on a underpinning system with Bauer SVV preloaded micropiles. The specialty of this underpinning job was that the building loads at the time of preloading and excavation of new basements was substantially less than at final stage. The design of the preloading system was particularly challenging in view of the transition from temporary to final load transfer under variable load conditions. Load transfer was based on the Bauer SVV micropile head system applied in several technical variants. Monitoring of levels of structural elements performed throughout the construction works confirmed that the differential movements of adjacent load bearing columns and walls were maintained within the specified limits.

Jan 1, 2002

By Ali Porbaha

In today's fast-track construction environment, owners are searching for non-conventional technologies to build their projects faster and safer while maintaining traffic flow during construction. To that end designers and contractors are providing solutions that incorporate many unique features to expedite construction processes. In addition to timely delivery of the finished highway products, there is an increasing interest in making the initial investment in applying innovative technologies and thereby minimizing costly maintenance of highway projects. Accordingly, the aim of this paper (along with the accompanying paper) is to examine innovative technologies, developed mostly in Europe, that accelerate construction of highway, runway and railway embankment foundations. For each technology, a basic concept, installation technique(s), and design considerations are discussed, along with the case history of a real-world project. The Geotextile Encased Columns (GEC), AuGeo, and Continuous Flight Auger (CFA) are presented in Part I. Deep Mixing (DM), Cut-Mix-Injection (FMI), Mass stabilization, and Combined soil Stabilization with Vertical columns (CSV) technologies are discussed in Part II.

Jan 1, 2002

By Matthew C. Pierson

Due to space limitations for transportation projects, many times sound walls must be constructed above mechanically stabilized earth (MSE) walls. These sound walls must resist lateral loads from wind or impact and must therefore be constructed on drilled shafts passing through the reinforced fill for the MSE Wall. Current design methods for the drilled shafts are believed to be overly conservative. Full scale lateral load testing of three foot diameter shafts contained within and solely supported by a 20 foot tall MSE block wall was conducted and the lateral capacity was evaluated. Shafts were tested individually and as a group. The data collected from full scale testing was then used to calibrate numerical models. This paper contains a discussion of how the facing type and stiffness affects the behavior of the numerical model as well as selected comparisons between the actual test data and selected model simulation results.

Jan 1, 2009

By Torsten Wichtmann, Jan Macheck, Frederik Broz, Patrick Staubach, Hauke Zachert

The majority of heavy or strongly loaded structures, for instance high-rise buildings, large span bridges or gas storage tanks are founded on pile groups. However, current design codes and guidelines do not provide a standard procedure for their design under lateral dynamic and high-cyclic loading arising from e.g. wind, temperature or earthquake loads. To establish appropriate design strategies, a better understanding of the pile-soil, pile-pile and pile-cap interaction is required. This paper is focused on finite element backcalculations of centrifuge tests on single piles and pile groups subjected to up to 500 lateral load cycles. For the finite element simulations, a special calculation procedure is applied, combining two kinds of constitutive models, a conventional (Hypoplasticity with Intergranular Strain extension) and a special highcycle accumulation (HCA) model. The parameters of the constitutive models are calibrated based on static and cyclic laboratory tests on the sand used in the centrifuge tests. The performance of the applied numerical procedure is evaluated based on a detailed comparison of the simulation results with the measured data from the centrifuge tests. Overall the applicability of the used numerical strategy for simulating the behavior of pile groups subjected to high-cyclic loading is shown.

May 1, 2022

By R. A. Fraser

Large diameter (1.0 to 2.5m) bored piles have been widely used to support buildings and elevated roadways in Hong Kong. Most of these piles are founded on a hard bearing stratum such as granitic or volcanic bedrock, in the newly reclaimed areas along the water-front, the bedrock stratum can be as deep as 70-80 metres below ground surface, and construction of bored piles to bedrock in this case is difficult and unjustified. Nevertheless, Building Ordinance Regulations in Hong Kong require piles to be founded on bedrock. To overcome this problem for elevated roadways, trial piles have been designed founded on dense, completely decomposed granite. A number of piles have been constructed and subsequently load-tested to allow the rate of mobilisation of skin friction to be measured. This paper outlines the design, construction and testing method, and comments on the test results from several trial piles. GEOLOCICAL CONDITIONS The geology of Hong Kong consists predominantly of acid volcanic rocks intruded by granite. The granite has been deeply weathered, and variations in sea level have produced a drowned coastline with sequences of alluvial, colluvial and marine deposits overlying the weathered bedrock. Reclamation has extended this coastline. Typical site conditions are described later in the paper.

Jan 1, 2010

By P. D. Arumairaj, B. Vani

"Micropiles are small diameter cast insitu reinforced grouted piles and it has been effectively used in many applications of ground improvement. It increases the load carrying capacity of soil and reduces the settlement. It is also used in strengthening existing foundations. In this study, the effect of Solid and Hollow micropiles on the load carrying capacity of footing resting on sand is studied. The effects of solid Micropiles are investigated by conducting experimental model studies. The parameters involved in this study include the position of pile, pile length and pile spacing. Load test was carried out on a model footing resting on sand with solid and hollow micropiles. Load test trail is repeated for footing on Micropiles with varying lengths of 10, 20, and 30 times the diameter and spacing equal to 5, 4, 3, 2 times the diameter. The load-settlement behavior of each case is compared. Optimum length and optimum spacing of both the solid micropile and hollow micropile are determined. It is also observed that the effect of micropiles in the peripheral of footing resists lateral displacement of soil underneath the footing. The micropile beyond significant depth becomes redundant.INTRODUCTIONA micropile is a small diameter (less than 300 mm) drilled and grouted pile that is typically reinforced - FHWA-NHI 2005 (Federal Highway Administration-National Highway Institution). It is constructed by drilling a borehole, placing a steel reinforcing element into the borehole and grouting it. Hollow micropiles are typically reinforced by solid central bar that occupies about onethird of the hole volume. The grout is placed by gravity, under pressure methods or by a combination of both (post grouting). Thus, micropiles can be considered as small drilled-shafts that are specially drilled and grouted.Historically, micropiles have been introduced in Italy as a foundation system mainly for retrofitting and underpinning of structures that had sustained damage during World War II and access for conventional piling equipment was not possible (Bruce, 1988). The second generation of micropiles is a pressure grouted piles with a central mono all thread bar (with diameter up to 89 mm). They are installed by using either an open or cased hole drilling method.A new generation of micropiles, termed Grout injection bore micropiles (IBOR), was developed in the 1980s. The IBOR, currently named hollow bar micropiles, utilizes a continuous all-threaded hollow steel bar as the drilling and grouting conduit, which allows drilling and grouting simultaneously without the need of a casing during drilling. A sacrificial (lost) bit with openings that allow for pressure grouting of the hole is threaded onto the end of the hollow bar and is left in place following drilling. A drilling fluid (air, water, or grout) is introduced through the hollow bar and allows the spoils to flush from the borehole opening. Upon reaching the required depth, neat cement grout is then injected under high pressure into the drilled hole to fill the annulus between the bar and the soil from the bottom to the top. Due to the grouting method employed, the shape of the hollow bar micropile is expected to have a bulb shape with an enlarged base."

Jan 1, 2015

By Ruth McKeown, Gilson de F. N. Gitirana, Murray Fredlund, HaiHua Lu

The current design standards for the use of anchors in slopes is based on two-dimensional (2D) limit equilibrium analyses. Anchors are considered as discrete loads and the 2D anchor, factored based on the spacing distance, corresponds to extending anchors indefinitely in the third dimension. A three-dimensional (3D) analysis offers a more realistic representation of the problem, including the true discrete nature of the anchor point loads. This paper explores the typical differences between analyzing anchors in 2D and 3D, using four typical conceptual models. Slopes with constant cross sections were shown to be adequately represented by the traditional 2D approach. The maximum difference between 2D and 3D models was 21% and becomes negligible for lower anchor spacing values, as expected. A slope with an external load was analyzed to evaluate critical slip surfaces with lower aspect ratios. Slip surfaces with lower aspect ratios presented higher edge effects that contributed to the stability of the slope. The results indicate that optimum design requires the 3D evaluation of field conditions inducing low aspect ratios, such as concave and convex surfaces, weak layers, and external loads. INTRODUCTION Slopes may be stabilized using a variety of solutions, including anchors. When performing an analysis, geotechnical engineers often follow the traditional two-dimensional (2D), Limit Equilibrium Method (LEM). It is important to understand the consequences and limitations of the assumptions on which the 2D LEM is based. There are numerous studies on anchors that show the importance of considering the actual three-dimensional field conditions. Desai et al. (1986) proposed a three-dimensional procedure based on the Finite Element Method and considering elastoplastic behavior and interface elements, to account for stress and displacement distributions, the relative motion between the anchors and the soil mass, and nonlinear soil behavior. Several important stabilization mechanisms were explained. The role of grout injection was evaluated in terms of the produced normal stresses along the anchor-soil bounding surface. The approach was shown to reproduce adequately experimental tests on a sand, proving realistic stress distributions around the anchor. Nonlinear soil behavior influenced to a large extend relative interface motions. Michalowski (1989) applied an upper-bound limit analysis in 3D to slope stability analyses. Anchors were not specifically considered in this study, but the consideration of locally loaded conditions shed light on important modeling aspects. The manner how the slide mechanism becomes three- dimensional as the slope is locally loaded was demonstrated. This emphasizes the fact that anchors should produce field conditions that require 3D analysis approaches.

Jan 1, 2019

By Daniel Levacher

Pile load tests in site require extensive means of action and time. To get outstanding tests, the environmental test conditions must be perfectly known and acceptable. They concern the support installation, the loading, the access and instrumentation site conditions and the economical aspects. In particular cases as offshore areas, the load tests are not feasible. Moreover the variability of soil characteristics limits the interpretation results at the considered tested site. The use of centrifuge modellling offers an other way to study the loaded pile behaviours. Centrifuge tests lead to parametric approaches which constitute for geotechnical engineers an important data base tor recommendations and design codes. To accurately simulate pile behaviours by checking similitude laws linked to the studied problems, the installation of model-piles must be also representative of the in-situ piles. Driven piles account for a large part of the piles installed through the world, mainly for offshore or harbour constructions. So, to explore driven pile problems by centrifuge tests, miniature pile driving hammers must be developed and tested under macro-gravities. The paper describes two types of these ones in details. They are commonly used at the centrifuge centre of the Laboratoire Central des Ponts et Chaussées - (LCPC) - [Réf. 1] for different deep foundations researches. Performances and limitations are given for both miniature pile drivers and some results from their use are presented to illustrate the suitability of these apparatus.

Jan 1, 1996

By K. K. S. Ho

In Hong Kong the design of excavated piles in weathered granite has conventionally been based on a rule-of-thumb which relates the allowable base bearing capacity to the SPT N value, with no allowance for skin friction. This rule-of-thumb has been shown to generally lead to conservative designs. To improve the overall understanding of load-transfer mechanism of excavated piles in weathered granite, instrumented pile load tests have been conducted. This paper summarises a selection of instrumented pile load test data in Hong Kong and the observations made of the results, which indicate that there was considerable scatter in the back-calculated skin friction values. However, the mobilized skin friction was shown to be significant which can lead to substantial savings in design.

Jan 1, 1996

By Fawad S. Niazi

Analysis of deep foundations in terms of axial capacity has been a topic of great interest in the soil-structure interaction problems. Soil behavior is governed by a series of complex stress-strain changes that occur during pile installation and subsequent loading. Owing to the difficulties and uncertainties on the basis of the soil strength-deformation characteristics, one of the most frequently followed design practice is to refer to the formulae correlating directly the pile axial capacity components of unit base resistance (qb) and unit shaft resistance (fp) to the data collected from cone penetration test (CPT), i.e. to the tip stress (qc or more proper qt), sleeve friction (fs), and shoulder pore water pressure (u2). The elementary basis for such formulations has been the idea of considering cone penetrometer as a mini-pile foundation. This has resulted in plethora of correlative relationships in the past over 60 years. Such correlations, although empirical, have been worked out on the basis of load test results from both instrumented and un-instrumented full scale piles and are able to accommodate many important variables. A quick review of the evolution process and development of such design formulations is presented with a view to propose recommendations for future research directions, where the latest version of CPT i.e. seismic piezocone test (SCPTu) can be used to advance from capacitysingularity to the complete axial pile load–displacement (Q–w) response.

Jan 1, 2013

By X. M. Wu

The paper describes four different types of support for deep excavations, which are currently used in China. Local experiences were illustrated by presenting case histories for each type of support. For braced excavation in soft clays in Shanghai, the earth pressure against bracings were found to be in conformity with the trapizoidal estimation given by Terzaghi and Peck (1967). For tie-back support of excavations in Beijing and Shengyang, earth pressures were found to be much less than those predicted by ordinary rules. In the construction of a mining shaft in coarse sand below ground water level, high pressure jet grouting has been successfully used to form a circular impervious lining of the shaft. As an effective anti-slide measure, large diameter reinforced concrete piles constructed by open shaft method have been widely used with success.

Jan 1, 2010

By George J. Tamaro

In 1967 the Port Authority of New York and New Jersey undertook the construction of the World Trade Center (WTC) diaphragm walls, installation of the lateral support system and the excavation of the site, commonly referred to as the "Bathtub". The work took two years to complete. In 2001 the City of New York undertook the re-excavation of the site after the terrorist attacks. The recovery work will take eight months to complete. This paper describes the initial work on the WTC "bathtub" in the late 1960s and the recent work during the recovery.

Jan 1, 2002

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By Anne Fagot

Because of the risk of corrosion caused by stray currents, steel foundations and steel sheet piling are generally prohibited in the vicinity of railway structures. Steel solutions are only accepted if they are shown to meet the required design working life and if this can be achieved at an acceptable cost compared to competing materials. The influence of stray currents on various steel sheet piling designs was studied using software initially dedicated to gas and pipeline industries and cathodic protection systems. It has been successfully adapted to model stray currents affecting steel sheet piling. Corrosion rates assessed using this modeling software were considerably lower than commonly expected. Zones of potential corrosion risk were identified; specific cost-effective countermeasures could be established. The developed software tool can help to optimize the design of piling solutions in the vicinity of DC railway power systems in terms of suitable countermeasures that meet structural reliability and cost requirements.

Jan 1, 2008

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By Juhyung Lee

Recently, large diameter drilled shafts are often used for foundations of large-scale marine bridges with high capacity and required to resist lateral loads. Steel casings are essential in supporting the hole-diving concrete installation of the drill shafts constructed in the sea. The casings, however, are usually not considered as the structural elements and their load bearing capacity is often overlooked in the design of drilled shafts. As the diameter of drilled shafts becomes larger, there are higher demands for more efficient and economical design of large-scaled drill shafts in the sea. Steel-concrete composite columns are popular for the superstructure of bridges, and the outer steel attached to the shaft increases the shaft resistance through confining the concrete. In this study, the lateral resistance of steel-concrete composite drilled shafts was evaluated quantitatively based on the numerical analysis. When steel casings are used as structural elements such as the composite columns. Ultimate lateral bearing capacity of composite drilled shafts with various diameters was numerically calculated through the 3D finite element analysis. For that, elasto-plastic model with the perfect plasticity is involved to capture the ultimate load. A commercial FEA program, MIDAS-GTS, is used in this study. Real field conditions of the west coast, Korea were examined to set up the ground conditions and pile lengths required for this parametric studies. Detailed characteristics of the stress and displacement distributions are evaluated for the better understanding on the mechanisms of the composite shaft behavior.

Jan 1, 2008