Search Documents

By Schmitz Stefan, Stephan Jee-Sun

"Due to the reunion of Western and Eastern Germany in the late 80’s, a multitude of infrastructure projects had to be executed. A good portion of these projects required improvement of the motorway system. In the southern region of Leipzig, in the eastern part of Germany, it was required to connect two existing motorways. Parts of the new motorway pass old strip mining areas. These strip mining areas consist of up to 70m thick backfill material. Especially the upper 20m are very inhomogeneous soil material with a very low bearing capacity. In order to increase the bearing capacity, to decrease the differential settlements and to homogenize the soil parameters, soil improvement using sand-gravel columns was required. Bauer Spezialtiefbau GmbH executed the installation of approx. 711,000 linear meters of columns with a length from 5 m to 25 m. For the project, 11 rigs with frame leads up to 40m were used to install the 43,000 columns with a diameter of 0.8m in 27 weeks.1. INTRODUCTION1.1 Site LocationThe construction site is located in the south-eastern part of Germany, in the south west of the city Leipzig.The area to be treated had a size of approx. 500,000 m² to allow the construction of dam/embankments and a highway bridge.1.2 Required WorkIn addition to the general earthworks and the installation of geogrids and fibre mats, a total amount of more than 710,000 linm of Gravel-Sand Columns with different lengths due to the given soil conditions had to be installed:•nos. 4,206 Columns length 5m ? 21,030 linm•nos. 4,581 Columns length 10m ? 45,810 linm•nos. 10,820 Columns length 15m ? 162,300 linm•nos. 19,634 Columns length 20m ? 392,680 linm•nos. 3,574 Columns length 25m ? 89,350 linmFor the installation of the columns Gravel-Sand with the grain size of 0/32mm was used. The total amount of Material was 580,000mt"

Jan 1, 2015

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more diffi cult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizing tie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State. INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges. Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story offi ce building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall."

Jan 1, 2007

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more difficult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizingtie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State.INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges.Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story office building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall"

Jan 1, 2007

By Md. Nafiul Haque, Murad Y. Abu-Farsakh, Chris Nickel

"This paper presents the results from a pile load testing program for a bridge construction project in Louisiana. The testing includes two 54-inch open-ended spun cast concrete cylinder piles (OECP), one 30-inch open-ended steel pile (OESP), and two (30-inch and 16-inch) square prestressed concrete (PSC) piles driven at two locations with very similar soil conditions. All the test piles were instrumented with vibrating wire strain gauges to measure the load distribution along the length of the test piles and the skin friction and the end bearing were derived from strain gauge measurements. High strain dynamic load tests (HSDLT) were performed on all test piles at different times after pile installations to quantify the amount of setup with time. Static load tests were also performed on the PSC and open-ended steel piles. Due to expected large pile capacities, the statnamic test method was used on the two open-ended cylinder piles. The pile capacities of these piles were evaluated using various CPT methods (such as Schmertmann, De Ruiter and Beringen, LCPC, COFS methods). The result showed that all the methods can estimate the skin friction with good accuracy; but not the end-bearing capacity. Setup was observed for all the piles, which was mainly attributed to increase in skin frictions. The setup rate parameters “A” [The “A” parameter is defined as the rate of increase of pile capacity ratio (Rt/Rto) per log cycle of elapsed time] were back-calculated for all the test piles and the values were between 0.31 and 0.41.INTRODUCTIONDue to greater efficiency (capacity to weight ratio) of the pipe piles, open-ended piles are a viable option to solid piles. However, the behavior of open-ended piles is more complicated compared to the close-ended piles owing to possible formation of “soil plug” inside the open-ended pile. Many researchers have analyzed the behavior of both types of piles for different purposes; however, very few studies in the literature offer the side-by-side comparison of the close-ended and open-ended piles."

Jan 1, 2017

By Andrzej Tejchman

A method of improvement of a subsoil under bored pile base by injection is presented. The method employs a special chamber attached to the reinforcement at the bottom of the drilled borehole. The chamber is made of semi-permeable textile bag. The injection entered under high pressure into the bag, causes prestressing of subsoil under the pile base. The results of load tests of piles improved in this manner have shown a substantial increase of their capacity together with simultaneous reduction of settlements. This technology has been implemented for four constructions such as trestle bridges in Gdynia and Warszawa and the bridges in Szczecin and Gdansk. The injection effects are shown based on the load test results.

Jan 1, 2002

By Tsuyoshi Honda, Kazuhiro Kaneda, Masayuki Imai, Kazuo Konishi, Kunio Higashinaka

"In recent years, the demand for measures to control liquefaction of existing airport runways and harbor structures has increased. However, from the perspectives of constructability and cost, application of grid-form deep mixing walls to these types of structures requires the formation of wider grid spacing as compared with conventional designs. In this research, we focused on the extent of liquefaction and ground surface settling when grid spacing is made wider than conventional designs. We conducted centrifuge model tests, and confirmed the liquefaction suppression effect when grid-form modifications involving wide grid spacing are adopted under asphalt pavement. The tests were conducted under conditions that included changing the grid spacing and groundwater level. When the groundwater level was high, an increase in water pressure was observed, even within the grid. However, when the groundwater level was low, the increase in water pressure inside the grid was suppressed. We also found that if the generation of water pressure can be suppressed, the amount of settling due to liquefaction can also be controlled.INTRODUCTIONOne construction technique used as a countermeasure to liquefaction is grid-form deep mixing walls. Grid-form deep mixing walls are a construction technique for which improved grid-shaped wall bodies are built into the ground below the surface using a deep mixing method. This construction technique minimizes shear deformation by surrounding liquefied ground with improved wall bodies, thereby preventing liquefaction (Fig.1). With conventional designs, grid-form deep mixing walls determine the grid spacing that can deter liquefaction based on a ratio of the grid spacing L to the improved depth H (ratio = L/H). Ordinarily, designs are implemented with an L/H ratio of 0.8 or less (PWRI, 1999).In recent years, a demand for measures to control liquefaction of existing airport pavement and harbor structures has increased. However, when liquefaction countermeasures are implemented at these types of facilities and structures, the construction work must be implemented while the facilities and structures remain in service. Therefore, temporal and spatial constraints must be considered. In addition, unlike conventional liquefaction countermeasures, performance requirements are such that, even if some degree of liquefaction is allowed, the performance is acceptable as long as the amount of settlement is within a predetermined value. Therefore, if grid-form deep mixing walls are applied to these structures, grid spacing that is wider than conventional standards is desired."

Jan 1, 2015

By Adel Hanna

Earth pressure acting on piles driven in sand is playing a major role in estimating pile capacity. In literature, researchers entertained simplifying assumptions in estimating the earth pressure acting on the pile's shaft, ignoring the effects of pile installation and pile size. Empirical formulae were introduced based on laboratory or field test results, where major discrepancies can be found among these formulae. In this paper, the theory of cavity expansion and the finite element technique will be used to establish the effects of pile installation technique and pile's diameter on the earth pressure acting on the pile's shaft and accordingly on the values of the existing coefficient of passive earth pressure and overconsolidated ratio. It is of interest to note that pile driven technique and pile's diameter have significant increase on the earth pressure acting on the pile's shaft and accordingly on the overconsolidation ratio in case of loose or medium sands, while they may cause crushing and dilation in case of dense sand. Keywords: Single pile, Cavity expansion, Cohesionless soil, Driven piles, Numerical modelling, Finite element technique, Earth pressure.

Jan 1, 2003

By John S. Pack

The application of square shaft helical piers in expansive soils is a standard of practice in many areas of the United States. Over 20 years of performance monitoring show exceptional performance and economy will result if proper design procedures, specification requirements and installation procedures are followed. This is true for new foundations and the repair of existing foundations, including lightly loaded wood-frame structures on expansive soils. Proper design includes: 1) site geotechnical characterization, 2) pier layout such that each pier is loaded to its maximum design capacity, 3) maximize spans between piers, 4) minimize the number of piers, 5) isolate the structure from the expansive soil with an appropriate void zone below all grade beams, slabs or other components that would otherwise be in soil contact and 6) utilize only single helix piers. Proper specification employs a performance specification that specifies: 1) the design load on each pier with a suitable safety factor, 2) the minimum installation torque, typically 4,000 ft-lbs (5.4 kN-m), or refusal, 3) a minimum pier shaft steel Fy = 70 to 90 ksi (483 to 621 Mpa) and pier helix steel Fy = 80 ksi (552 Mpa), 4) 1.5 to 1.75 inch (38.1 to 44.5 mm) square shafts, 5) smooth shaft surface, 6) the ICC Evaluation Report (ER) number of the manufacturer and 7) the manufacturer ISO 9001 certification for material quality control. Proper installation requires: 1) equipment with sufficient axial compression force (crowd) on the pier shaft so the helix engages the soil and advances to the specified minimum installation torque or refusal, 2) additional specialized techniques for expansive soils and 3) qualified specialty helical pier installation contractors experienced in expansive soils who submit and utilize pier configurations, techniques and equipment that will most effectively and economically meet the specified performance.

Jan 1, 2007

By Daniel Stevenson, Richard Guenther

"The preservation of historic buildings is not only essential to the understanding of our national heritage, but it is also environmentally responsible to adapt existing buildings to compatible new uses. With this perspective, the American Enterprise Institute began exploring options to expand the newly acquired Andrew Mellon Building, located at 1785 Massachusetts Ave. NW in Washington, D.C., without causing any harm to the Beaux Arts style limestone façade and its plaster interiors. The building is a National Historical Landmark, but its 72,000 sq ft (6,690 sq m) of usable floor space did not meet the needs of its new owner. The building perimeter is very near the property line, so horizontal expansion was not possible. Adding height to the building was not an option, as this would have altered the historic nature of the building exterior. The only feasible option that could provide the desired floor space was to add a new floor underneath the existing structure. By adding a level beneath the existing building, an additional 28,000 sq ft (2,601 sq m) of floor space could be produced.Berkel & Company Contractors was chosen as the deep foundation/shoring contractor tasked with ensuring that the existing structure was stable and remained undamaged during the excavation and construction of the new lower level. To accomplish this, Berkel provided a shoring system that would act as both excavation support and permanent deep foundation elements for the final structure.Preservation of the existing limestone façade and plaster interiors was critical to the success of the project, as additional foundation settlements could damage these irreplaceable building components. Project specifications, therefore, included very stringent limits for foundation settlements. The maximum allowable total settlement for all existing building walls and columns was ¼ in (6 mm) for the duration of the project."

Jan 1, 2017

By V K. Panwar, Sampat Raj

At a Fertilizer plant located in the southern part of India, 74 numbers of pump foundations have shown non-uniform settlements causing the tilting of pump foundations under self-weight primarily due to the presence of varying thickness of the heterogeneous subsoil beneath the pump foundations and soil erosion because of water seepage through deeper excavations in the close vicinity. Various corrective measures have been explored and taking due cognizance of the prevailing subsoil conditions, site constraints, and constructability aspects, micropiling has been adopted. This paper presents the site problem and details of remedial measures adopted for rehabilitation of the distressed pump foundations. The main objective of this paper is to provide guidelines for designer during design and detail engineering stage to avoid similar nature of problems and also to provide a solution concept to tackle similar nature of problem(s) if encountered at site.

Nov 1, 2022

By Abolfazl Eslami, Fatemeh Valikhah

"Complexity in soil-foundation interaction and subsoil nonlinear behavior cause difficulties and uncertainties in evaluating the actual values of foundation design factors such as settlement. The acquired continuous records of Cone Penetration Test (CPT) can be used to determine the soil profile and characteristics those are applicable in the geotechnical design. In this paper, it has been attempted to present a new non-linear stress-strain approach to estimate the foundations settlement by using CPT data in the form of soil behavior classification charts. This new approach is based on Janbu method (1960s and also 1998). Instead of using fixed and constant values for stress exponent (j) and modulus number (m), continuous coefficient variations can be used. The proposed approach also can be used as a new method to predict pile group settlement. A data bank has been compiled containing twenty-two practical case histories to investigate the accuracy of the predictions made by the proposed and available common methods. The comparisons indicate that the proposed approach is relatively able to predict the settlement close to their real values. Therefore, it can be considered as an alternative method based on valuable CPT data and nonlinear stress-strain approach for foundations and pile groups settlement estimation.INTRODUCTIONComplexity in soil behaviour for settlement analysis is the result of non-linear and time dependent stressstrain behaviour of soils, their elasto-plastic performance under loading and unloading situation and also effects of stress history (Holtz et al., 2011; Fellenius, 2015). Hence, many relations and equations have been proposed to predict foundation settlement, where most of them are based on typical different parameters such as soil stiffness (E), foundation width (B), contact pressure (q) and pressure developing in depth (Janbu, 1967 also 1998; Briaud and Gibbens, 1999; Uzielli and Mayne, 2012).The Janbu approach for settlement estimation, proposed by Janbu in the early 1960s, combines the basic principles of linear and non-linear stress-strain behaviour of material. The method is applied to all types of soils. The relation between stress and strain is a function of two non-dimensional parameters which are unique for any soil: a stress exponent, “j”, and a modulus number, “m”. The Janbu relations are derived from the definition of tangent modulus by the following expression:"

Jan 1, 2017

By Arvindh Gupta

BC Hydro proposed to improve the stability of the existing Seven Mile Dam with 54 corrosion protected, re-stressable anchors comprising 92/0.6? strands each, in phase 2 of the program. Being globally the largest capacity anchors ever build, coupled with extra ordinary specifications, the project was a challenge for the entire post tensioning industry. The paper discusses the challenges associated with the anchor material supply as per specifications, extensive research and development carried out by Con-Tech Systems ltd. to overcome the challenges and contribute in making the project a success. The substance of this article is published in the Aug/Sep issue of ADSC magazine.

Jan 1, 2004

By Axel J. Pollak

Since the late 1960's the Interstate Division for Baltimore City (IDBC) has been planning and developing the Interstate Highway System for the city to meet regional planning goals. The principal goals are to provide convenient access to the central business district and the port while diverting through traffic away from these congested areas. Interstate Route 95, an eight-lane highway carrying north-south traffic, has headed the city's priority list; during the 1970's its construction proceeded steadily from both east and west towards the harbor. Closing the final 8800-ft (2670-m) gap under the harbor will complete Interstate 95's construction. This final portion, known as the Ft. McHenry Tunnel project, will be built in nine construction contracts. Construction costs of the complete project are expected to exceed $700 million, making it the costliest single project in the Interstate Highway System. Full funding is being provided initially by the Federal Highway Administration (FHWA), and the Maryland Department of Transportation will re-pay the 10 percent local share from toll receipts within the first three years of operation.

Jan 1, 1989

By P. M. Deshpande

An interactive short column system is evolved as alternative to deep foundation system in deep layers of marine clay, the interaction of encased stone column and marine clay carry load without causing conventional settlement. This paper presents concept of the system and its field application as foundation of culverts on marine clay layer of 15 to 17 M underlain by residual soil layer of 5 to 6 M, where conventional pile of 23 to 25 M would have been required.

Jan 1, 1996

By Mohab Sabry, Emre Biringen

"Over the past decades, there has been an increasing recognition of the strategic use of pile-supported rafts in design of heavily-loaded structures to reduce total and differential settlements. However, such a hybrid foundation construction method has not been widely utilized in many countries, including the U.S., due to code limitations. In current practice, the foundation design is based on either (i) the bearing capacity of the raft supported by the subgrade soils, or (ii) solely the pile capacity. This paper addresses the potential use of such hybrid piled-raft systems, where the structural load is shared by both by the piles and the subgrade soils directly beneath the raft, in foundation design of power plant structures. The study assessed some of the characteristics of piled-raft behavior by undertaking three-dimensional finite element analyses of two raft sizes, and various pile layout patterns, including the rafts with piles distributed evenly and only in the central area of the raft. The computer software PLAXIS 3D with the Mohr-Coulomb constitutive soil model was used to facilitate the modeling of such cases. The results presented in this paper indicate how strategically locating the piles could reduce the differential and total settlements.INTRODUCTIONUnder the high applied loads coming from the superstructure, the addition of piles is primarily required to improve the factor of safety against failure when a raft does not provide adequate bearing capacity. If the bearing capacity of the raft is sufficient to carry the total load with a reasonable safety margin, then the addition of piles is usually intended to reduce the settlements to an acceptable amount. In current practice, the design process for pile-supported raft foundations conservatively concentrates on providing solely the pile capacity to carry the total structural load without taking the contribution of the raft into account. This paper addresses the potential use of hybrid piled-rafts in controlling foundation settlement of power plant structures by considering the support of both the piles and the subgrade soils beneath the raft to carry the load."

Jan 1, 2017

By Andrew Baxter

This paper focuses on the design of steel bearing plates to transfer load from tiebacks and tiedowns to a concrete mass. It lists and describes the various available procedures for design of bearing plates as well as explains the design procedure recommended by the authors, which incorporates the Post Tensioning Institute (PTI) recommendations. The paper includes a step-by-step design example following the recommended procedure that captures the most important aspects of plate design. The dimensions of the plate calculated from this example are compared to the design dimensions obtained from various other procedures, including those by American Association of State Highway and Transportation Officials (AASHTO) and VSL International, Ltd. (VSL). The paper also includes the results of numerical modeling of the plate that will help the reader understand important aspects of plate-concrete interaction. The authors envision that this paper will serve to create an understanding in the geo-industry of suitable design methods and help improve procurement of bearing plates for tiebacks and tiedowns.

By Gerald Verbeek, Erick Baziw

"Downhole Seismic Testing (DST) is an important geotechnical testing technique for site characterization as it provides low strain (<10-5) in-situ interval compression (Vp) and shear (Vs) wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. A challenging aspect of this process is to characterize the seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. This paper introduces an assessment technique which utilizes linearity estimates (i.e., hodograms fitting straight lines) from the polarization analysis in conjunction with crosscorrelation coefficient calculations of the full waveforms as well as the deviation of the source wave frequency spectrum from a desirable bell-shaped curve. The paper will provide an overview of the technique and include some examples of actual data sets where the technique was applied to analyze those data sets.1. INTRODUCTIONIn general terms, Downhole Seismic Testing (DST) such as Seismic Cone Penetration Testing (SCPT) is a geotechnical technique for measuring in-situ shear and compression wave velocities (VS and VP respectively). The main goal in DST is to obtain arrival times as the source wave travels through the soil profile of interest, and from these arrival times the velocities are then calculated. Figure 1 shows a schematic of the typical DST configuration: a seismic source is used to generate a seismic wave train at the ground surface. One or more downhole seismic receivers are used to record the seismic wave train at predefined depth increments. The downhole receiver(s) may be positioned at selected test depths in a borehole or advanced as part of an instrumentation package as in the case of SCPT. When triggered by the seismic source a data recording system records the response of the downhole receiver(s)."

Jan 1, 2017

By Jamey Rosen, Georgette Hlepas

Verticality data collected from panel and pile elements of seepage barrier walls describe the shape and position of those elements in three dimensions. These data are used to determine if a barrier wall is constructed as designed and if it meets the owner specifications with respect to tolerance (i.e., if each element is sufficiently close to vertical) and overlap (i.e., do adjacent elements overlap sufficiently to prevent leakage). Contractors use verticality data to confirm that their work matches the design, and owners use verticality data to verify the contractor’s work and confirm that specified criteria were met. Project Information Management Systems (PIMS) technology has been applied to the management, visualization, and analysis of verticality data. This paper will provide examples of how contractors and owners have used a PIMS to compile and synthesize data collected during excavations (e.g., from Cutter Soil Mixer and Hydromill drill rig telemetry), and from measurements of completed excavations (e.g., using the Koden ultrasonic tool), and used those data to model excavation geometry. We will present case studies of using these models to estimate backfill placement volumes, and to evaluate the verticality tolerance and overlap between elements.

Sep 8, 2021

By Alessandro Bertero, Manuel Toniolo, Vincenzo Tirozzi

"The installation of foundation elements (large-diameter Bored Piles or Diaphragm Walls) for the execution of underground works to be performed through the ""Top Down"" Technique (Stations, Car Parks, Subways, Artificial Tunnels) often requires the insertion, with pinpoint accuracy, of steel or prefabricated elements within the foundation system, to provide temporary and/or permanent support to the whole structure.The future high-speed railway station of Florence Belfiore (Italy) is a perfect example; the new station will be built in the Northwest area of Florence, about two kilometers far from the existing station of Santa Maria Novella. The project envisages installation of about 500 bored piles (1200-1500-2100 mm diameter), with lengths ranging between 50 and 70 m. In the upper inner part of 250 piles, a steel pipe (weight: 15-20 tons, length: 22-25 mt.) has to be inserted with pinpoint accuracy.The “TREVI-CALATORE” system allows to install the plunge columns and adjust their position and verticality.INTRODUCTIONThe execution of underground works via the ""Top Down"" technique, train or tube underground stations, parking shafts, tunnels, often implies the need to carefully insert steel or prefabricated structures, serving as provisional/definitive pillars, into the foundation elements.The future high-speed railway station of Florence Belfiore is a perfect example; the new station will be built in the Northwest area of Florence, located about two kilometers far from the existing station of Santa Maria Novella.The new Belfiore Station is part of the new European high-speed railway network. The works related to Florence urban penetration include (figure 1):•,a 6.5 km. twin tunnel excavated via TBM/EPB, that will run beneath Florence in a north-east direction,•,passing under more than 150 buildings, many of which can be considered historic buildings, with a soil•,coverage ranging from 6 m to 20 m;•,a North portal in Rifredi area, Firenze Castello Station;•,a South portal near Campo di Marte Station (which is also the launch shaft of the TBM)•,the new Underground Station in Belfiore area."

Jan 1, 2016

By Athena C. Denivo, Pablo V. Lopez, Sissy Nikolaou, Alfred H. Brand, Ahmad Rahimian, Rudivien G. Josef

"The United States Tennis Association (USTA) Billie Jean King National Tennis Center (BJKNTC) site is located in the northeastern portion of the Flushing Meadows Corona Park area of Queens, N.Y. The site occupies some of the most difficult subsurface conditions for construction in the New York City (NYC) metropolitan area, with unique challenges from geotechnical, seismic and foundation design perspectives.At the USTA site, Paleozoic crystalline bedrock is found at a depth of roughly 300 to 400 ft (90 to 120 m) below grade. The geologic history of the site is complicated, starting from the early Pleistocene, when the ancient Hudson River temporarily changed course, flowing across Queens enroute to the Atlantic. It eventually carved a deep valley through the Cretaceous soils, in some places all the way down to bedrock. A series of glaciers advanced and retreated across the region during the Pleistocene times, filling the deep valley with layers of assorted glacial soils. At its southern edge, the last major glacier to flow across the region built up a ridge at the southern tip of Flushing Meadows known as the Harbor Hill terminal moraine. This ridge blocked the valley forming a dam, so as ice started melting away the valley filled up with a lake fed by glacial meltwater. Layers of clean outwash sand and varved silt and clay filled the glacial lake. The ice did not retreat in a steady manner, instead periodically readvancing over the previously deposited soil in the lake, then retreating far enough to let the lake drain temporarily into Long Island Sound, before readvancing again.As a result of this repeated sequence of retreat, advance, retreat, etc., there are places where a “crust” of desiccated soil formed when the lake drained, and areas with interlayers of outwash sand where ice readvanced into the lake. When the ice melted north of Long Island Sound, the glacial lake filling Flushing Meadows drained forming Flushing Creek. During the Holocene (roughly the last 11,000 years), as ice melted further away and sea-level rose, low lying areas filled with river sands and marine clays, along with coastal marsh deposits. Table 1 lists the soil design properties on site and Figure 1 exhibits the geologic section across the site."

Jan 1, 2015