Search Documents

By Fidelis T. Suorineni

The conditions for rockburst occurrence are traditionally identified as: high stress, high extraction ratio, strong brittle rocks, folding, faulting, and unfavourable excavation geometry. Based on a critical review of case histories, this paper identifies oblique loading of orebodies by the major far field principal stress as a cause of rockbursts. Orebodies subjected to this loading condition are termed orebodies in shear. Orebodies in shear are subjected to compressive and shear loads. The case histories presented unambiguously show that the magnitudes of the far field principal stress alone, and a knowledge of the conventional rockburst causing factors are not sufficient for mine planning and design. The orientation of the major far field principal stress, or for that matter the driving stress relative to the orebody axis, should be recognised as one of the causes of rockbursts. It is suggested that since stress orientation is an important factor, and orientations from stress measurements are so variable, orientations from stress measurement data be complemented with underground observations from borehole and excavation breakouts to determine the actual in situ stress orientation, whenever possible. Also stress modelling for the design of critical elements (pillars) should include a sensitivity analysis on the relative critical field stress direction. The paper emphasises that special attention should be paid to or

Jun 1, 2012

By F. Rosenblum, P. Spira

"A correlation has been established between the oxygen demand of Brunswick Mining and Smelting ore and flotation results at the bench, pilot plant and operating plant scale. A method of dete""1llining the aeration requirement of sulphide ores on the basis of this correlation is presented. It is shown that abraded iron from grinding media plays an important role in aeration and flotation. Laboratory grinding must therefore be conducted under controlled conditions with suitable grinding media in order to obtain the true aeration requirement of the ore.A method of evaluating aerator efficiency, also based on oxygen demand measurements, has been used successfully at Brunswick Mining to design pilot plant and full-scale aeration systems.1. IntroductionPre-flotation aeration of sulphide pulps has been practiced in the Noranda Group for many years to help in the depression of pyrite and pyrrhotite and to promote chalcopyrite and/or galena. Recently, two out of three parallel circuits at the Brunswick Mining and Smelting Corp. Ltd. concentrator have been converted on a test basis to a new flowsheet incorporating aeration as a basic step. Among other benefits, a substantial decrease in the middlings load has been achieved as a result of improved pyrite rejection. There has been increasing interest in other organizations in the potential advantages to be derived from' aeration in terms of improved metallurgy and/or decreased reagent consumption."

Jan 1, 1978

By Jarret Thomson

An understanding of groundwater flow is essential for many aspects of mining. This is especially true for the process of shaft sinking through the sandstones of the Manitou Falls Group in the Athabasca Basin of northern Saskatchewan. Experience has shown that the hydraulic conductivities of these sandstones can be relatively high, especially in zones containing natural fractures. To develop a better understanding of the inflow potential into a shaft, a laboratory testing program was undertaken to investigate the hydraulic conductivity of fracture core samples from the Manitou Falls Group. This program involved the measurement of hydraulic conductivities under steady-state flow conditions, while cycling the effective confining pressure across a span that is representative of in-situ conditions. The change in fracture aperture was simultaneously recorded at each confining stress level. It was found that existing relationships relating aperture and flow did not accurately capture the behavior of the samples tested. The effects of fracture staining and infilling were also investigated, and were found to have a notable impact on the hydraulic conductivity.

Jun 1, 2012

By J .. R. Dalton

"Blasting in high sulphide content ores presents at least two major safety considerations: (1) compatibility of the explosives with the ore while resident in the borehole; and (2) introduction of a flame and shock producing explosive into this environment, while minimizing the risk of reactive ignition in the chemical reaction products/sulphide dust cloud resulting from the detonation. This paper will discuss only the second consideration, i.e. post detonation reactivity.The ETI (Explosives Technologies International) Technical organization, in consultation with the U.S. Bureau of Mines, reasoned that the most relevant considerations in the development of an explosive for this application are:• minimization of reactive gaseous detonation reaction products;• flame duration reduction;• flame temperature reduction;• increased explosive sensitivity;• reduced probability of ""low order"" detonation; and• maintenance of energy level as high as possible.Obviously, not all of these are totally independent properties, i.e. increased sensitivity will reduce the probability oj low order detonation as will higher energy levels. However, these considerations were examined separately as if they were independent."

Jan 1, 1994

By J. Oliveira, A. R. Barnes, R. Pandher

Sub-stoichiometric roasting of arsenic-bearing copper ores is a well established practice. However, ores containing calcium commonly prove challenging where very low arsenic levels are desired, but the reasons for this phenomenon have largely been speculative. In the course of treating arsenicbearing copper ores by partial roasting in fluid bed reactors, XPS encountered one of these Ca-bearing ores which proved a challenge to roast to acceptably low levels of arsenic. Mineralogical examination of the calcines using a combination of XRD (X-ray diffraction), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro-Analysis) helped to identify the arsenic bearing species and assisted in developing a workable theory on the sequence of reactions occurring during the roast. With the assistance of thermo-chemical modelling, this allowed adjustment of the roasting conditions to minimise the amount of arsenic retention in the calcine in spite of the presence of calcium in the ore and advance the roasting program to a commercially acceptable solution.

Jan 1, 2014

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By M. Potesser

In the past, different furnace types have been developed for use within the copper industry, with two common anode furnace designs typically used in copper smelting plants worldwide: the tiltable reverberatory furnace (KPO) generally used for the secondary copper industry and the cylindrical or drum type anode furnace (TRO) for handling a liquid blister charge generated in primary copper production. The disadvantage of the KPO is its design related to the longer refining period, because of the low bath depth, however it provides good conditions in the melting period due to its large bath surface. On the other hand, small amounts of scrap charged into the TRO increase the melting and dissolution period, but it provides good conditions for the refining period. The newly-developed elliptical furnace concept (TRE) offers the advantages of each of these furnace types. The special design allows melting of the scrap more efficiently than in the KPO and refining the liquid copper more efficiently than the TRO. This paper shows a metallurgical comparison of the three furnace types in regard to the melting period by heat technological considerations (optimized arch design) and of the refining period done by CFD with concentration on current, recirculation and dwell time of the gas in the melt. The paper outlines the possibilities for a reduction of the tap-to-tap time and energy consumption as well as for an increase of the production capacity, which can be achieved by applying the TRE instead of the conventional furnace designs.

Jan 1, 2007

By Weiren Lin

The Mw 9.0 Tohoku-Oki, Japan earthquake occurred on 11 March 2011 produced a maximum coseismic slip of >50 m near the Japan Trench. To investigate why the plate boundary fault between the subducting Pacific Plate and overriding North American Plate which caused the earthquake had such unprecedented large coseismic displacement and slipped to the trench, Integrated Ocean Drilling Program Expedition 343 called Japan Trench Fast Drilling Project (JFAST) drilled three boreholes at Site C0019 through the earthquake fault about one year after the earthquake. Borehole C0019B dedicated to loggingwhile- drilling (LWD) penetrated ~850 meters below seafloor (mbsf) at a water depth of approximately 6890 m. The plate boundary fault is located at ~820 mbsf in the borehole and has been identified as the slip zone during the Tohoku-Oki earthquake. Borehole wall resistivity images obtained from LWD show that drilling induced borehole breakouts are available in a wide depth range above the fault but are not available below the fault. Breakouts are reliable indicators of the orientations of current maximum and minimum horizontal stresses and can also be used to constrain the horizontal maximum and minimum stress magnitudes. As results of breakout analyses, the maximum horizontal stress orientation highly varied in the upper part of the borehole, but has a clear preferred orientation in a northwest – southeast direction in the deeper part just above the fault. This orientation is approximately parallel to the direction of the Pacific Plate subduction. Stress magnitude constraints indicate that the post-earthquake stress states in the hanging wall are either in or close to the normal faulting stress regime. By inferring the pre-earthquake stress state and comparing with the constrained post-earthquake stress state, a significant coseismic stress change was interpreted. The stress change suggests an active slip of the frontal plate-interface consistent with coseismic fault weakening and a nearly total stress drop.

Jan 1, 2015

The recovery of fine hydrophilic gangue in flotation is related to the recovery of water. Water is carried by bubbles as a film and wake into the froth. The amount carried (entrained) depends on bubble size, gas rate and the subject of this paper, frother type. To isolate the effect of frother type from that of bubble size and gas rate, gas holdup is used as the correlating variable. Measurements were made using a bubble column (no solids) operated continuously with the overflow recycled. Continuous operation meant some foam depth was required to ensure only entrained water is recovered. Using an automatically controlled 7cm foam depth the overflow rate of water is used as a measure of 'water carrying rate'. It is shown that the common frothers can be grouped into four families based on the water carrying rate-gas holdup relationship.

Jan 1, 2006

By K. M. Tait, M. M. McDonald

"An overview of the status of the development and application of Integrated Gasification Combined Cycle (IOCC) power generation is presented. Current projects in North America, Europe and Japan are described, together with the status of plans to apply the technology in Canada. A brief review of the technology is presented, including promising coproduction cycles and hybrid gasification fluid bed processes. The ability of the process to be modified for CO2 to be extracted for enhanced oil recovery or disposal is addressed. The environmental impact of IGCC technology is compared to those of other power generation technologies IntroductionDefinition and HistoryIntegrated Gasification Combined Cycle (IGCC) technology is a concept which has been around for about 50 years but has been generating increasing interest in the last 10 to 15 years. This paper focusses on coal as the feedstock for gasification. Other feedstocks used in gasification systems have included oil, biomass, tires and petroleum coke. IGCC technology integrates coal gasification with generation of electricity by means of a combined cycle system which fires the produced gas in the gas turbine. Figure 1 shows the basic components of an IGCC system which are the gasifier, the gas cleanup system and sulphur recovery plant, the gas turbine/generator set, the heat recovery steam generator (HRSG) and the steam turbine/generator set. The benefits of an IGCC system over a conventional Rankine Cycle pulverized coal (RCPC) fired system for the generation of electricity from coal are that the IGCC system has potential to have higher efficiency and lower emissions of NO., SO and CO2 per unit of power produced than the corresponding RCPC system."

Jan 1, 1994

By J. Roth

"While not taking issue with the general thesis expressed in Dr. Ridge's analysis of the role of genetic concepts versus observational data in ore exploration (Ridge, 1983), the criticism could be offered that the author tends to slight the importance of conceptual (i.e. theoretical) models in mineral exploration.As a general rule, observational data in science lacks significance and utility without a theoretical construct to organize those observations. Theory in turn dictates what observations are made-and which ones are judged important. Thus, for example, prior to the elaboration-and acceptance- of the current model for volcanogenic base metal deposits, the structural aspect s of these deposits were most closely observed and studied by explorationists. The nature of the enclosing rocks and any attendant alteration was given minimal attention, and certainly didn't figure prominently as an exploration guide.Similarly, the importance of alteration features to exploration for porphyry copper-molybdenum deposits was only perceived when a theoretical model was developed to account for these aspects. Indeed, many of these porphyry copper deposits were regarded as epigenetic vein deposits by geologists of an earlier era observing and examining on a different physical scale-and with a different theoretical bias.In constructing and evaluating such conceptual models, explorationists primarily rely on observation data and proximate associations; speculative thoughts as to ultimate provenance or crustal evolution clearly play a subordinate role, as Dr. Ridge argues. This, however, should not obscure the fact that concepts and theories do indeed exert a major influence in mineral exploration."

Jan 1, 1983

By Behzad Vaziri Hassas, Firat Karakas, Esra Tanisali, Mehmet S. Çelik, Ahmad Hassanzadeh

Coagulation is basically an aggregation process where particles settle under the influence of interfacial forces with electrostatic forces playing a governing role. Although particle morphology consisting of shape and roughness dictates the physical encounter of two particles, their eventual coagulation is not only influenced by columbic forces but also other interfacial forces such as hydrophobic interaction, which affects the extent of aggregation of particles through increasing the distance of interaction. Roughness is well known to increase the effective contact angle on hydrophobic surfaces and also enhance interfacial forces. In this study, the effect of morphology of particles and particularly roughness on the settling velocity and in turn coagulation tendency was investigated. Batch settling tests (BSTs) of different particle morphologies were investigated as a function of pH. Two different morphologies of silica particles were utilized with the same particle size distribution (PSD) including smooth-spherical and rough-spherical (Etched). Rough particles were prepared by acid etching technique using hydrofluoric (HF) at different time intervals (15-300 sec). Etched samples were identified and quantified by optic profilometry. Settling test results showed that the settling velocity of particles in a suspension of 2% solids in the massive settling region is significantly affected by particle morphology of the suspension. Coagulation results further revealed that aggregation of rough particles is faster than smooth-spherical particles. Coagulation results are elucidated on the basis of particle morphology and its effect on distance of separation through hydrophobic forces.

Jan 1, 2016

By John O. Marsden

Technology development and innovation has played a crucial role in the copper industry throughout history. The effective development and implementation of new technologies allows mankind to produce copper at progressively lower cost of production at a given feed grade and mineral type. This progress serves to counteract cost escalation over time and, depending on the magnitude of the cost benefit, allows ore cut off grades to be reduced thereby improving the availability, accessibility and utilization of mineral resources. The development of step change technologies that can offer >$0.15/lb total cost benefits provides a significant opportunity for producers to achieve competitive advantage, but it has been argued that rapid dissemination of technology makes such competitive advantage unsustainable over time. This paper presents the results of a recent study that evaluates a number of historical and emerging step change technology case studies in the copper industry and quantifies the associated cost benefits for users, the impact on the production cost curve, and the duration of such cost benefits for various categories of implementers: first mover, fast follower, conservative followers and laggards. The results provide a compelling case for major, mid-tier and emerging copper producers to invest in technology development initiatives if they wish to achieve and sustain competitive advantage over the long term. INTRODUCTION AND BACKGROUND A key issue for mining companies is how much time, effort and cost to spend on research and technology development (R&TD). The economic drivers for technology development and implementation are poorly understood in our industry and the business case is clouded by some notable and well-publicized failures (McNulty, 1998). Mining companies are in business to deliver financial returns to investors. This means delivering short term results on a quarter-by-quarter reporting basis as well as sustaining and growing the company to retain and reward a sustainable longer term investor base. The cyclical nature of the commodity metal markets makes it challenging to maintain investment in research and step change technology development: Mining companies must manage through the highs and the lows of price cycles, typically ranging from 5-15 years in length. The discounted cash flow approach to investment evaluation results in weak financial justification for R&TD expenditures. A clear and compelling rationale to support longer term investment in research and step change technology implementation is required.

Jan 1, 2019

By Robert A. Creaser, Iain Mitchell, Robert L. Linnen

Abstract - The Bermuda Zn-Pb showing is hosted by dolomitized Blue Fiord Formation of Devonian age, located east of the Ensorcellement dome on the Grinnell Peninsula of Devon Island. Fluid inclusions in hydrothermal calcite indicate that the mineralization precipitated from low-temperature, highly saline brines. The ?34S compositions of sphalerite, galena, and marcasite range from 16.1‰ to 35.2‰. Consequently, the Bermuda showing is interpreted to be Mississippi Valley-type (MVT) mineralization. The apparent age of mineralization has been determined by the Rb-Sr method from sphalerite separates, and a Late Devonian age of 357 ± 50 Ma (MSWD=65), with an initial 87Sr/86Sr ratio of 0.7083 ± 0.0020 is indicated. This date, within error, is the same as the Polaris deposit. This suggests that the mineralization formed during the Ellesmerian Orogen, although it is also possible that mineralization is associated with extension, related to the opening of the Sverdrup basin. The strontium and sulfur isotopes and fluid inclusion analyses indicate the involvement of a brine that acquired its salinity from interaction with evaporites, lower in the stratigraphic succession. The Polaris mine is the type deposit in the Cornwallis Zn-Pb district and is hosted by the Thumb Mountain Formation. The results of this study are significant because they demonstrate that regional brine movement is more widespread than previously recognized, and that MVT mineralization in the Cornwallis Zn-Pb district is not restricted to the Thumb Mountain Formation.

Jan 1, 2004

Terrane?s Canadian Assets Mt. Milligan, British Columbia Copper, gold (100%) Berg, British Columbia Copper, molybdenum (100%) Howards Pass, Yukon/NWT border Zinc (Option payments, and Royalty interest) Maze Lake, Nunavut Gold (Joint venture with Laurentian Gold Fields)

May 1, 2010

By C. R. Whittemore

PROGRESSIVE industrial organizations have recognized the importance of maintaining an adequate reference library of volumes covering all phases of their particular branch of industry, but it has been the experience of the writer that few engineers know how to use to the best advantage this store of extremely -valuable information which has been accumulated for their service. Nor does the average engineer appreciate the fact that it is only through the current technical literature that he can keep abreast of the rapidly developing fields of engineering. The present-day ramifications of the engineering field are of such wide scope that the human mind is not capable of storing away more than a small fraction of the information available on any particular topie; yet, from time ? to time, such information would prove invaluable. An engineer can know intimately only a small part of his own branch of engineering; but he cannot afford to neglect to take the fullest possible advantage of all that is already known in his own particular field. Technical information may be obtained by one or more of the following methods: (1) by enquiring of the individual who knows; (2) by performing the experimental investigations necessary to ascertain the facts; (3) by consulting the technical literature, where a record may be found of the work of others. This last method is the one we wish to examine. Our main consideration is the question of how to use the library, but first it is necessary to give some attention to the kind of enquiries one takes to the library, and to the nature of the sources of information available.

Jan 1, 1938

By M. Mirnezami, J. A. Finch, M. S. Hashemi A.

The surface of -30µm silica suspension (2% v/v) treated with 100 ppm Mg2+ at pH 11 was fully coated with Mg(OH)2. Under this condition, the silica is strongly positively charged (+30 mV) and the suspension is dispersed. Subsequent addition of Ca2+ promoted aggregation and reduced the surface charge. At this pH calcium is present as Ca2+ and CaOH+, i.e., positively charged ions interacted with the positive surface. Aggregation by a chemical bridging mechanism is proposed. The observation may be relevant to the widespread practice in mineral processing of adding lime to promote aggregation and settling in concentrate thickeners.

Jan 1, 2004

Agenda 1.Energy consumption and energy costs ?focus and failings 2.Energy efficiency methodologies, people and supporting tools 3.Energy cost saving case studies from three minerals processing plants 4.The operations team and the supporting role of Operations IT 5.Conclusion: Reducing energy consumption and energy costs There are many good Energy Efficiency Methodologies ?Energy and GHG Emissions, Management Guidance Document, The Mining Association of Canada ?Energy Savings Toolbox ?An Energy Audit Manual and Tool, Canadian Industry Program for Energy Conservation (CIPEC) ?Lean and Energy Toolkit, Achieving Process Excellence Using Less Energy, www.epa.gov/lean ?Energy Efficiency Opportunities Assessment Handbook, www.energyefficiencyopportunities.gov.au

May 1, 2010

By N. Hwang

There has been increasing interest in the use of robotic machines, and several prototype robotic machines have been developed to automate the grit-blasting process for the purpose of steel bridge maintenance. To utilize such a robotic grit-blast machine effectively, the first consideration is automating the determination of the rust surface area to blast, on the basis of standards of practice, in a rapid manner. This study aims to propose a method to rapidly and accurately determine the rust surface area on steel bridges to blast, with consideration for the standards of practice, from images acquired via a blasting machine. The first step is to perform a color space conversion to transform the input image from a red/green/blue (RGB) color space to a hue/saturation/intensity (HSI) color space. The next step is to detect the presence of rust, using pixel-level classification via the C4.5 decision tree algorithm. Then it is necessary to confirm the blasting area by verifying whether the rust detection result satisfies the specified criteria on the basis of standards of practice. The proposed method was validated on 39 test images with various characteristics with respect to the degree of rusting and rust distribution type. The experimental results showed that the average accuracy rate of rust area classification was about 97.63%, and the success rate of the final decision of blasting area determination was 100.00% for 39 test examples. The whole processing time took an average of only 0.86 seconds per image. The preliminary results demonstrated that the proposed method not only determined whether rust was present in an image and the amount of rust but also indicated whether blasting was necessary, and, if necessary, it rapidly specified the rust surface area that should be blasted on the basis of standards of practice. The proposed method could be successfully incorporated into a robotic grit-blast machine.

Aug 1, 2013

By Nickvinder Bhath, Johnson Matthey Plc, Jamie Baker, Daniel Kim, Jeff Lucht, Shijie Wang

"Precious metals (PM) in copper anode slimes are traditionally recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of precious metals, including relatively inert metals such as gold and platinum group metals (PGMs). In this paper, a new method to recover PGM from complex and difficult feed streams is described. Using a proprietary Advanced Ion Exchange (AIX) adsorbent which has a high selectivity for PGMs over other metals and can achieve high PGM mass loadings with a series of incredible pilot test data plus the business case generated from the study results are also presented in the paper.INTRODUCTIONPrecious metals in copper anode slimes are traditional recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of many metals, including relatively inert metals such as gold and platinum group metals (PGMs). Fully hydrometallurgical processes for extraction and recovery of gold and silver from copper anode slimes were employed in major copper refineries since 1995, which was first developed at Rio Tinto Kennecott Utah Copper.In Rio Tinto KUC process, the wet chlorination and gold solvent extraction were utilized to enable recovery of gold and silver as well as other metal compounds. The availability of water and the interaction and amenability of gold processing in water-based solution makes it possible that gold and silver are produced in only five days, compared with a traditional pyrometallurgical process that took 45 days. Most copper refineries are still following the tradition, but the use of hydrometallurgical technologies is increasing as the world demand for metals increases, energy utilization, and environmental viability."

Jan 1, 2016