Search Documents

By K. J. Mintz

Conveyor belts installed in an underground mine can be a potential source of a major fire, thus the need for fife-retardant belting. A Canadian Standard, CAN/CSA-M422-M87, incorporating a small-scale flame test, a drum-friction test, a flame propagation test and an electrical surface-resistance test, has been developed to meet the varied needs of the mining industry. It is recommended that mines use Types A and B belting described in that Standard, because they will have passed the large-scale flame propagation test, rather than Type C, which does not require that test. Belting that has been approved by the U.S.A. Mine Safety and Health Administration (MSHA) may be much less fire-retardant than any Canadian approved belting.

Jan 1, 1992

By L. A. Wolff

"Second only to profitability (but not always), productivity is the most sought after measurement for any operation. Whether it is in mining, manufacturing, construction, etc. managers always strive to know how productive various plants are. Even the Federal Government publishes, on a monthly basis, the nation's factory productivity.Just what is productivity and how is it measured? This is an important topic that needs definition. There could be as many definitions as there are people who use it. In the mining industry, the problems of defining productivity would be analogous to the definition of equipment availability. Each mine uses its own definition to suit its needs. Webster's Dictionary primary definition for productivity is ""the quality or state of being productive,"" with productive defined as ""yielding or furnishing results"". This is a definition open to a broad spectrum of interpretation. A discussion of how productivity is currently used in the mining industry and an introduction to a potentially different approach to its measurement and meaning is outlined in this paper.Defining ProductivityTypically, mining companies track several productivity measurements. These are partial measurements and can include the following: tons per specific equipment class per hour, tons per man-hour, and tons per shift. None of these, however, track the over -all performance of an operation, that is, a unit of output per unit of input.For a mining operation, output can be defined as the ore for mill processing. Input includes the required components of production to get to the first step of processing.The Wesbter's Dictionary definition exposes a major fault with the popular conception of productivity. The critical issue of accountability is not addressed. Anyone can produce, but how effectively and efficiently are resources used? Quantifying an inclusive measurement is difficult. Statistics referring to an increase in productivity are often published. For example, the statement, ""gold productivity has increased by 10%"" has many potentially dangerous interpretations. One must ask, what does this statistic really mean? Did gold companies produce 10%” more gold? Were less manpower or equipment required to produce an equivalent amount of gold? Did ore grades increase resulting in more ounces of gold produced, etc. Obviously, production and productivity can have similar implied applications and meanings, but also two different, distinct meanings.To mitigate a problem like this, a standard needs to be developed within the mining industry. Because of varying ore grade, changing waste to ore ratios, different mining methods, etc. all of which have a direct impact on mining, development of a standard is difficult. Kendrick(1) discusses the use of Total Factor Productivity as a productivity measurement. Summarized, the total factor productivity measure is an indication of the change in efficiency in the use of basic labour and capital factors associated with an operation.This measurement has little meaning when calculated at a given point in time. It should be an on-going calculation, tracking an operation over a period of time, to evaluate trends. These trends can be used to determine if an operation's productivity is what it should be, and alert management to potential problems before they become major and adversely affect an operation."

Jan 1, 1990

By S. M. Fatemi-Varzaneh

The AZ31 magnesium alloy is considered as a promising alloy in various applications and industries. Furthermore, to design a proper hot working process (rolling, forging and extrusion), the assessment of hot working behaviour of the alloy is necessitated. Accordingly, the hot deformation behaviour of AZ31 alloy was studied through hot compression testing method. The latter was carried out in a wide range of temperature (523 K to 783 K) and strain rates. The obtained true stress-true strain curves and final microstructures were examined and a partial melting was realized at 740 K. It was concluded that the presence of liquid did change the deformation mechanisms thereby affecting the flow behaviour.

Jan 1, 2005

By G. Ladouceur

"Northgate Patino Mines produces a copper concentrate assaying 22% Cu. Moisture content of the product averages 12.5% H20 when dewatering with conventional vacuum disk filters. Recent smelter contracts reflect higher energy costs and increased moisutre penalty charges. This situation forced Northgate to investigate possible alternatives such as rotary dryers and pressure filtration. After laboratory testing, it was found that pressure filtration could economically meet the smelter's requirements. Pilot plant testing was then undertaken and confirmed the laboratory test results. Based on these findings, a model I.S.F. 1500 x 28/22 I.R. Lasta filter press was purchased.This paper describes the Copper Rand dewatering flowsheet the operation of the press and the economics of the process.IntroductionNorthgate Patino Inc. operates 2 und erground copper mines and a 3300 ton per day concentrator located in Chibougamau, Quebec, some 425 miles north of Montreal and 300 miles northeast of Noranda, Quebec.Copper concentrate is produced at a rate of 250 tons per day and trucked to a C.N. siding 10 miles from the mill site and then railed to the Noranda Smelter.Until early 1981, moisture content of the concentrate at 12.5070 was acceptable since smelter penalty charges were relatively low ($0.10 per ton per unit over 10070 moisutre). In January 1981, a new contract was signed in which the penalty was raised to $1.10 per ton per unit over 8070 . This and the increasing truck and rail costs justified the change-over from vacuum to pressure filtration . The Lasta I.S .F. 1500 x 28/22 was then purchased and installed, and operation of the plant started in December 1981."

Jan 1, 1987

Concentrator Improvements -1990-1995Back to Basics ?pilot plant versus plant opportunities identified ?understand process fundamentals & baseline -1996-2000Point ?C?Projects ?strategy to improve global competitiveness ?structure implemented to generate & drive ideas ?capital investment for life of mine asset renewal - 2001-200?Six Sigma Methodologies ?emphasis on data, measurements & analyses ?dedicated, highly trained personnel on projects 1990-1995 Improvement Phase??Philosophy??back to basics?approach?understand what each piece equipment needed to do?understand reagents, control variables?confirm operating strategies ??probe, stabilize, institutionalize??test theories, confirm with lab and plant trials?process stability (equipment reliability, controls)?enhanced operator guidelines, operator training?focus on continuous improvement?optimize existing equipment capability?stop looking for ?magic?solutions 1990-1995 Improvement Phase??Technical?finer grind, same equipment?optimize media size/shape to grinding application?balanced available ball mill power to applications?lowered cyclone feed densities where possible?improved selectivity, same equipment?balanced available cells to applications?streamlined process (eliminate process steps)?added cleaning stages where required?understanding pulp/mineral surface chemistry?lowered flotation pulp densities 1990-1995 Improvement Phase??Effort?numerous studies to understand process?liberation and mineralogical characterization?pulp and mineral surface chemistry?flotation kinetics and entrainment?extensive internal and external manpower?Brunswick, Noranda Technology Centre?CanMet, AMTEL, MinnovEx, Lakefield Research, McGill University?small capital expenditure

May 1, 2002

By G. Sperlins

"IntroductionBrenda Mines Ltd. is a low-grade open-pit mining and milling operation located near Peachland, B.C. Brought into production in late 1969, the plant treats an average of 30,000 tons per day of an ore that contains 0.130% copper and 0.030% molybdenum.The operation is divided into six areas of responsibility, namely the mine, mill, plant, accounting, industrial relations and purchasing /stores departments.The purchasing and warehousing area handled in excess of 11,000 items valued at $31,000,000 in 198J. Over and above this, the warehousing area issued in excess of 74,000 line items valued at $15,000,000 during that same period.Materials Management- DefinitionWhat is meant by the term ""Materials Management""? Reference to the dictionary will reveal that a material is ""that of which anything is composed or may be constructed; the tools, instruments, implements', etc. for doing something"". Management is defined as ""the act, or manner of managing; the skillful use of means to accomplish a purpose"". Presumably combining these words defines materials management.Of greater importance are the materials managers who will carry out the function. At Brenda Mines Ltd., all employees and suppliers contribute to the materials management function. Each has a specialized knowledge of the materials used in his field. Each has a different view concerning the use and description of the same material. The key is to focus this knowledge so as to make the materials management system useful to everyone."

Jan 1, 1982

By R. Krentz, P. D. Cordingley

The nickel-cobalt sulphides produced from limonitic laterite ores by Moa Nickel S.A. in Cuba are refined at the Corefco nickel-cobalt refinery in Canada. Major changes to the refining process were required when the Moa sulphide feed, with its unusually high cobalt content, was introduced in the early 1990's. In the period 1994 to 2005 the production capacity of the refinery has increased dramatically to match increases at Moa, and significant process improvements incorporated. The process flowsheet consists of the original ammonia leach process, optimized for cobalt chemistry and overall leaching capacity. Extraction of metal values is followed by the unique nickel-cobalt separation technology, in which most of the cobalt is separated from the ammoniacal nickel sulphate leach solution by precipitation as a nickel-cobalt hexammine salt. This salt is refined from a Co:Ni ratio of 1:1 to over 10,000:1 by selectively leaching nickel, redissolution and recrystallization in ammonium sulphate solution. Nickel and cobalt are recovered using the well-known Sherritt hydrogen reduction technology. This paper reviews the chemistry described above, examines some of the changes in operating conditions made over the years and highlights some of the recent physical changes made to the refinery.

Jan 1, 2005

By G. Russo

During the construction of the S.Martin La Porte access adit, 9m in diameter, extreme squeezing conditions occurred while crossing Carboniferous schistose formations, with diametric convergence up to 2m. Back-analysis of monitoring results shows that an acceptable simulation of the observed excavation behaviour can be derived using a combined analytical and numerical approach, with simple elasto-plastic laws but a progressive reduction of residual parameters and a relevant increase of dilatancy.

May 1, 2009

By G. R. Haiden, E. Henderson

"An LHD teleoperation and guidance system, developed at the Ontario Division of Inco Limited, has been demonstrated in operation at Copper Cliff North Mine (CCNM) since late September, 1993. The tests performed to date have evaluated the feasibility and production viability of multiple LHD operation, from surface by one operator.The systems technology required to accomplish this consists of an electronic monitoring and control package mounted on the LHD; a high bandwidth mining computer network capable of providing radio frequency coverage; and an operator control console which provides an operator workstation for multiple LHD operation.This paper discusses the systems required to accomplish the task of LHD teleoperation and guidance, the benefits of multiple machine operation and future research and development directions. IntroductionSince underground mining began, persolU1el have entered the mine workings to mine ore. Today, however, the rapid advancement of modem telecommunications, computer hardware and software technology has opened the door to remote mining technology that was considered unfeasible a few years ago. This paper discusses the ingredients of remote mining technology that have been developed at Inco Limited.Figure I represents an historical view of the application of electronics to LHD operation at Inco Limited. In 1980, the first radio remote controls for the operation of LI-IDs in large open stopes were tested. The successful application of this technology at Inco went hand-in-hand with the development and application of the Vertical Crater Retreat mining method. The combination of these two advances had a very positive effect on the productivity in the mid-eighties at Inco. In 1991, the Mines Research Department of the Ontario Division advanced remote control technology by developing a high capacity underground mining telecommunications system. This system is capable of moving voice, data and video information throughout the mine workings. The system is based on broadband communication technology found in most automated factories, with the added benefit of providing the information to and from mobile equipment through radio interfaces. The first test of the system consisted of an operator teleoperating a single LHD (on the 3000 ft level) from the surface. The next test on September 13, 1993, demonstrated the first production application of multiple LHDs being run from surface with a single operator."

Jan 1, 1994

By J. Suarez

The innovation initiatives for world-class mines today and in the future focus on automation and robotics in equipment and machinery. These innovations have benefited from the development of advanced tools in global positioning, the Internet, the capabilities of data storage, transmission and handling, and intelligent systems. Forward-thinking companies have been investing in automated trains and trucks, selfdrilling rigs, intelligent flotation systems, etc. Considering that the emphasis has been mostly laid on improving the performance and reliability of the equipment and machinery, it is not surprising that the visibility was geared toward mechanical, electrical, process, and metallurgical engineering. One of the critical disciplines, mining engineering, has had less shine from the spotlight of automation and robotics. Mining engineering is concerned with the design, the operation, the management, and the reclamation of mines and mining facilities. In essence, it does benefit from the advantages of automation and robotics in equipment and machinery. However, being ?left out? in the innovation process may impede the core capabilities of this engineering discipline, which would create a two-tier knowledge and technology system in mines. For example, shovels in an open pit may be equipped with technology that can send real-time data of actual payload, number of buckets, mechanical status, etc. But, are mining engineers aware of the possibility to incorporate the data into their planning tools in order to have updated forecasts and accurate information? And if they are, are they equipped with the tools to reap the rewards of those technologies? And if so, is the personnel trained to use the tools efficiently? This paper is a contribution to the discussion on the technological advances in mining engineering. For the authors, the roadmap to the future requires a smart integration of technological advances in hardware and software so that mining engineers are not only aware of the possibilities, but also trained and capable of using the available tools. Essentially, this paper believes that automation and robotics in equipment alone will be undervalued and underutilized if the owners and drivers of the mining systems (i.e. the mining engineers) do not possess the tools and training to integrate the technological advances into the functions of mining engineering. The intent of the paper is to analyze the available technologies for the core mining engineering functions of design, planning, scheduling and optimization. The analysis will lead to discussions and suggested solutions on integrative technology solutions that would create optimum value for the mining processes and equipment technologies.

Aug 1, 2013

By M. H. Moys, C. Bhondayi, Eric Tshibwabwa

"The relationship between froth bubble size as represented by intra-bubble impact distances (IID) and flotation performance is investigated. Experiments using an artificial ore comprising of limestone as the floatable component and silica as the gangue material were carried out in pseudo-steady-state circuit. A method to measure IIDs developed by Bhondayi and Moys (2014) was then used to measure froth bubble sizes as a function of froth height, superficial gas velocity and feed rate (pulp residence time). Samples for flotation performance evaluation were also taken. Results indicate that as froth height increases, the average IID values increase resulting in a decrease in limestone recovery while the grade increases. Increasing gas rate results in lower IID values that are accompanied by high recovery and low limestone grade. The effect of feed rate on both flotation performance and average IID values depended on froth depth and gas rate. Average IIDs largely remained the same at the two feed rates investigated.INTRODUCTIONIt is regarded as obvious that froth bubble size distribution (FBSD) will have an effect on plant grade and recovery. As the average FBSD decreases, the bubble surface area flux will increase making possible an increase in recovery and a decrease in grade. The opposite trend will be involved if average FBSD is increased. However: no method for measuring FBSD has been available, so these trends have not been studied in any detail. Bhondayi and Moys (2014) developed a novel technique to measure or estimate froth bubble sizes. Although they established a potential to use this method in understanding froth performance, no data have been presented to assess the correlation between the estimates of bubble sizes and actual flotation performance. In this work experiments are done to establish how the change in froth phase bubble sizes affect flotation performance. Flotation performance will be evaluated using recovery and grade. How water recovery to the concentrate changes with changes in bubble sizes will also be evaluated. It is known that water recovery is approximately inversely proportional to the square of the overflowing bubbles sizes. It will be interesting to establish how the rate of change of bubble sizes changes with water recovery."

Jan 1, 2016

By J. C. Kurnia

Presence of fine dust in air causes serious health hazard for mine operators resulting in such serious problems as coal workers? pneumoconiosis and silicosis. Major sources of dust appear of course along the mining face where the minerals are extracted. Proper control and management are required to ensure safe working environment in the mine. Presented here is the use of a computational fluid dynamic (CFD) approach to investigate the flow and dust behaviour in mining tunnels. The objective of this study is to propose and examine various strategies to mitigate dust dispersion from the mining face and reduce dust concentration to a safe level for the operator. In a companion study, the authors investigated various methods for mitigating dust dispersion from the mining face to ensure safe dust concentration levels in the mine tunnel. Among the examined methods, implementation of brattice to direct the flow from the main airway to the mining face is the most effective method to disperse dust particles away from the mining face. The installation of brattice, however, will limit the movement of mine operators and vehicles in the tunnel. Hence, application of a hybrid brattice which is a combination of a physical brattice along with suitable directed and located air curtains is proposed and examined. Based on the CFD simulation results, over a range of parameters of interest, it was found that the physical brattice blocks the ventilation air and directs it to the mine face while an air curtain located along the brattice outlet offers flexibility in keeping the dust away from the operator allowing more freedom for the operator and the equipment. Results of the modelling over a range of parameters of interest are presented and discussed with the goal of managing dust concentrations within safe limits for the operator.

Aug 1, 2013

By H. M. Giegerich

"INTRODUCTIONThe Red Dog Project in Alaska is being developed by Cominco Alaska, a subsidiary of Corninco Ltd. of Canada, and the Nana Regional Corporation, one of the 12 native corporations created by the Alaska Native Claims Settlement Act of1971.The State of Alaska is also a very key part of the project through its financing of the transportation system for Red Dog. Red Dog will be the third, and largest, of Cominco's Arctic mining developments in the past thirteen years, after the Black Angel Mine in Greenland, which started up in 1973, and the Polaris Mine in the Canadian Arctic, which began production six years ago in 1982.Red Dog is one of the world's great mineral deposits, with a unique combination of large size, high-grade, and a waste-to- ore ratio less than I: I, which will make it the world's largest, and one of the lowest cost zinc producers, when at full production. The present mineral reserve is estimated to be 85 million tons , at a grade of 17.1010 zinc, 5% lead, and 2.4 ounces per ton of silver. Based on the current production forecast, this will give a mine life of almost 50 years, and the deposit is still open in two directions, although the structure is becoming thinner at depth. As well, there is a satellite zone about one mile south of the main deposit which could contain up to another 8 million tons of mineral at Red Dog grades or better. This is not presently included in the reserve due to potential processing difficulties.In relation to other zinc deposits, Red Dog is the second largest ever discovered, smaller than the original Broken Hill deposit in Australia, but larger than Cominco's own Sullivan Mine in British Columbia, which is number three. It is quite possible that, when the area is adequately explored, Red Dog will be number one."

Jan 1, 1989

By Robert B. Parsons

"During hard times, the focus on tax issues makes a slight change in direction. Mining companies contemplate the tax treatment of transactions and circumstances which are the product of a difficult financial environment. Some of these issues are discussed in this month's edition of Tax Notes.Every industrial sector in Canada is undergoing a major restructuring of some form, and the mining industry is not an exception. The longest recession since the Great Depression continues to affect the economy. Mining firms seek to bring their debt/equity ratios into line, and try to replenish depleted retained earnings by selling assets. This month, Tax Notes briefly examines some of the tax issues which are generally encountered during the course of such a restructuring process.Debt SettlementOne question which commonly arises during hard times concerns the tax treatment of a "" gain "" realized by a debtor on the settlement of a debt. Consider, for example, a simple situation where a creditor wants to protect itself from further losses, and makes a deal with the mining company to accept a cash payment of $8 million in full settlement of a $10 million loan. In financial terms, the debtor has made a $2 million gain on the settlement of the debt. What is the tax treatment of that gain?The Income Tax Act (the Act) contains provisions in section 80 of the Act and in section 5400 of the Income Tax Regulations which deal specifically with this question. First of all, it is noted that the $2 million gain is not brought directly into income for tax purposes. However, as indicated below, the gain could affect the debtor's income indirectly to the extent that certain of the debtor's tax pools must be reduced by the amount of the gain."

Jan 1, 1993

By Robert B. Parsons

"Thrashing one's way through a jungle of entangled tax rules is no easy task today, as Canada's legislators continue to complicate this country's income tax laws. At some magical point, there is presumably some balance to be struck between legislation which is equitable and unambiguous on the one hand, and at the same time is efficiently complied with and administered. It is becoming increasingly clear that the legislation is not in balance, and that there is a pressing need for some simplification of the income tax rules and regulations especially in areas of critical importance to the resource industries-even though such simplification will likely involve some sacrifice of equity and certainty.Introduction""I would wish that ... the superfluous and tedious statutes were brought into one sum together, and made more plain and short, to the intent that men might better understand them."" Edward VI, King of England 1547-1553.Regal decree notwithstanding, the legislation of most developed nations continues to become more complex, lengthy, and confusing than ever before. Canada's income tax system cannot escape the accusatory finger pointing at examples of this serious problem which plagues all of us today.Although many areas of our tax law could easily warrant some degree of simplification, for those who are involved with this country's resource sector, that horrendous, almost unreadable, part of our tax legislation which deals with resource taxation must be regarded s a prime candidate for simplification. In recent decades, but particularly in the past ten years since tax reform in 1972, budget after budget, both federal and provincial, have amended, massaged, modified, and manipulated the resource tax rules to the point where not only are taxpayers totally lost in their attempts to make some sense of the entanglement of rules, but also the draftsmen themselves acknowledge that the outer limits of complexity are being reached, and that the whole set of rules is on the verge of grinding to a groaning halt under its own weight of nonsense and frustration."

Jan 1, 1982

By Stephen B. Hearn

The SLon Vertical Ring and Pulsating High Gradient Magnetic Separator was developed to overcome multiple disadvantages associated with traditional horizontal type Wet High Intensity Magnetic Separators (WHIMS) which have been in service for many decades for recovering iron ore and other minerals. Proven successful, with hundreds of units now upgrading low-grade iron ores and maximizing recovery of fines throughout China, the technology is now being tested in the Western world. This paper will discuss the drawbacks of traditional WHIMS, explain the operation of the SLon, and illustrate its practical use in processing hematite ores.

May 1, 2007

By Brian O'Hearn, Doug Hanson

"The most commonly used tendon supports in the Sudbury area include rock bolts, rebars, friction anchors and cable bolts. Due to the fact that these tendons are physically different and employ different anchoring systems they offer varying degrees of stiffness, yield ability, load capacity, anchor dependability and energy absorption. These differences coupled with variable rock mass and changing stress conditions have made it challenging to engineer the design of an effective support system. By tapping into the knowledge and experience gained by ground control practitioners, an empirically based rating system has been assembled that offers a guide to designers of support systems when choosing the most effective tendon support over a range of rock mass and stress conditions.A methodology referred to as support planning can be used to design support systems whose rehabilitation costs will be minimized. The use of multiple tendon types in anyone support layout is advocated, particularly when the stress state of the rock mass to be supported is expected to undergo a change."

Jan 1, 1995

By Sebastian Siebert

Unmanned Aerial Vehicles (UAV) as a data acquisition platform and as a measurement instrument have become attractive for many surveying applications in civil engineering. However, their performance is not well understood for these particular applications. The specific scope of the presented work is the performance evaluation of a UAV system that was built to rapidly acquire mobile 3D mapping data for large earthmoving construction sites. Details to the components of the developed system (hardware and control software) are explained. A novel program for photogrammetric flight planning and its execution for the generation of 3D point clouds from digital mobile images is explained. A performance model for estimating the position error was developed and tested in several realistic construction environments. Results to these tests are presented as they relate in particular to large excavation and earth moving construction sites. Results and experiences with the developed UAV system are in particular useful for researchers or practitioners in need for successfully adapting UAV technology for their application(s).

Aug 1, 2013

By Leonard A. Wolff

"The 1980sfor the mining industry can be characterized as the survival of the fittest. High interest rates, low commodity prices, foreign subsidized competition and decreasing ore grades have contributed to a streamlining of the domestic mining industry in the United States, leading to the shutdown of operations or large cutback of work forces. The purpose of this paper is to look at the impact of a layoff on the employees of what was once a major uranium producer in south central Wyoming, twenty months after the final layoff and mine shutdown. INTRODUCTIONDecember 19, 1985, was the date of the final of three successive layoffs over a two-month period, leading to the complete shutdown of Petrotomics Company, a subsidiary of Getty Minerals Company. The final shutdown was due to a combination of depressed U3O8 prices and the takeover of Getty Oil Company by Texaco in January 1984.The layoffs affected 104 employees and included mine personnel, mill personnel and staff. Both hourly and salary workers were involved. The operation was considered non-union, however, a few mill hourly employees were unionized. At the completion of the layoffs. only a handful of employees remained for administrative and miscellaneous functions.For Getty employees, the terms of the merger agreement provided a generous level of separation benefits. The terms that were insisted upon by Mr. Petersen, Chairman of the Board for Getty Oil, stipulated that employees receive one month of severance pay, for each full calendar year of employment up to a maximum of two year's pay. This was the forerunner of what is now commonly known as the ""tin parachute”. All but the union employees of Petrotomics received these separation benefits. Union employees were covered by their separate, less generous, contract.Much of the literature that has been published in recent months has centred around the effects of layoffs on remaining employees, or the psychological effects on the severed employee. This study will emphasize the economic impact and ramifications due to a layoff, using the Petrotomics employees as a case example."

Jan 1, 1989

"Classification is an important aspect of mineral processing plants and if not operated efficiently can compromise both the throughput and recovery of the circuit. This paper discusses the benefits that can be obtained by operating the classification section efficiently. Since classification in most of the mineral processing plants is carried out using either hydrocyclones or screens the case studies involving the two classifiers were used in the discussion. Studies where optimising the classification circuit lead to improvements in the performance of the overall plant were included to show the benefits of paying attention to this area that is usually neglected. The data from the mill-float mill float, SABC, and Single Stage SAG mill circuit case studies have shown that the circuit throughput can be increased throughputs without compromising recoveries by optimising the classification circuit. On plants where the ore can be liberated at coarser sizes the experimental results have shown that replacing hydrocyclones with high frequency screens can lead to improved plant throughput with no detrimental effect on recovery. The discussion has included information on design and operational considerations for plants that have or intend to use hydrocyclones or screens that could make the classification circuit more efficient.INTRODUCTIONComminution is the process in which particles are reduced in size mainly by crushing and grinding. In most mineral processing circuits comminution is carried out to liberate the valuable minerals prior to subjecting the ore to a recovery process were values are concentrated or extracted (Mainza, Evertsson, Benzer, Tavares, Powell, Rule, Plint, …, 2013). Comminution is an energy intensive process and is usually achieved in stages. It is common to have a classifier after each comminution stage. The process is carried out in stages to minimize energy usage and to improve the efficiency of the process in meeting product specifications. Although comminution circuits have been advancing classification has remained a key component of the comminution circuit design (Mainza et al., 2013). Mainza et al. (2013) summarised the role of classification in mineral processing circuit as: to allow material in the equipment that can promote high operational efficiency, to improve material handling in the circuit, to minimize overgrinding of material to reduce energy consumption, and to provide the best quality product to enter the next stage of processing. Classification stages are employed in comminution circuits to ensure that high throughputs are processed without compromising the product quality or to produce a fine product at relatively low energy. If neglected classification can have detrimental effects on plant performance."

Jan 1, 2016