Search Documents

By Schoeman L., K. C. Sole

Evaluation and measurement of the influence of changes in conditions and electrolyte composition during early stages of a growing metal electrodeposit are crucial to predict changes in developing morphology. A galvanodynamic polarization technique was developed to reliably measure overpotentials for nickel electrodeposition from sulfate electrolyte. The validity of these polarization parameters as indicators of the relationships between changes in the electrolyte and resulting deposit morphology was evaluated for electrolytes of varying composition. Findings indicate that nucleation and plating overpotentials measured by the described technique can be used as indicative tools for monitoring, evaluating and ultimately improving control of the electrodeposition of nickel from sulfate electrolytes. The results predict that nickel deposits of desirable quality and morphology are obtained when plating overpotentials are higher than 700 mV vs. Ag/AgCl and nucleation overpotential is less negative than plating overpotential.

Jan 1, 2017

By B. F. Giyani, D. Rahal

"Stirred media mills have proved to be more energy-efficient than the conventional ball milling for fine grinding applications. The mill performance is governed by a number of operating variables including mill stirrer speed, feed particle size, solids content and slurry rheology. A study was conducted to assess effects of mill speed, media size and density, and slurry density on the Stress Intensity (SI) in a VXPmill and thereby the relationship to mill performance. For the mill speeds tested, it was found that the optimum tip speed is 7 m/s. If the speed is too high (12 m/s) energy losses result due to mechanical friction losses and heat generation. If the speed is too low (3 m/s), the kinetic energy is not sufficient to promote breakage. The size reduction ratio increases with the increase in mill speed and the decrease in solids content especially in the coarse fraction particle sizes. The effect of slurry rheology on mill performance was shown by assessing the effects of increasing solids concentration and decreasing particle size. Rheological effects seemed to interact with mill speed such that the mill was less energy-efficient at higher solids content and at higher mill speeds particularly for grinding to fine particle sizes. There is an opti"

Jan 1, 2017

By N. Schreithofer, M. Aspiala, R. Serna

The novel attachment timer apparatus presented in this paper serves as a diagnostic tool that allows the detection of changes in bubble-particle attachment probability and therefore floatability caused by alterations in the chemical environment and particle properties. The apparatus consists of six identical capillaries where bubbles with defined size are produced simultaneously in a measurement chamber. The bubbles at the capillary tips are placed in contact with the submerged particle bed for specific time periods, controlled with the help of automatic actuators. The advantage of the instrument is that hundreds of bubble-particle contacts can be measured automatically within a short time period. Microscopic pictures of each measured bubble are taken while recording the movement of the bubble before, during and after contact with the solid particles. The recorded pictures can be used to determine the actual bubble size and its corresponding deviation, and to detect the attachment of particles. The attached particles are collected in a detachable chamber for subsequent characterization. Furthermore, the device is portable and can be taken to the mineral processing plants for quick evaluation of particle-bubble attachment efficiency with particles and process water sampled directly from real processes.

Jan 1, 2017

By Sergio Bustos

A significant expansion project is under way at KATCO?s Torkuduk In Situ Leaching (ISL) operation to increase uranium production up to about 4000 tU/year. Higher flows and lower uranium concentration are expected in the rich solutions coming from the well fields. Therefore, extra adsorption and elution columns and modified operating conditions are required to deal with the increased demand for uranium transfer from the ISL solutions to the eluate solution, which goes to the uranium precipitation section. Resin adsorption and elution performance have been interpreted and projected by using Mac Cabe-Thiele equilibrium diagrams. The resin load, the adsorption mass transfer coefficient, the adsorption zone height and the eluate concentration have been estimated for the expected changing operating conditions associated to the future mine plan. This information has allowed to improve the present operation results and to define the main process design criteria for the expansion project.

Aug 1, 2010

By Eugene Sun, Qiang Xu

This presentation will review current applications of composite materials in aircraft design and discuss the challenges involved in maximizing the potential of the composites in aircraft applications.

Jan 1, 2010

By C. Feng, D. W. M. Arrigan

Arsenic is often associated with gold mining operations and poses a significant health and environmental hazard. While a number of technologies are available for removing arsenic, none of them is effective under all conditions. Although adsorption is a promising approach, most methods focus on the purification of water under neutral or acidic conditions and tend to be less effective in gold mining process waters, operating under alkaline conditions. In this study, the removal of As (III) and As (V) from both arsenic-only solutions and simulated process waters using composite magnetic nanoparticles was investigated. The nanoparticles consisted of magnetite (Fe3O4) or maghemite (?-Fe2O3) cores covered by various metal oxides with Langmuir adsorption capacities of As (III) and As (V) ranging from 31.4 to 79.1 mg/g and 10.2 to 25.5 mg/g, respectively, in arsenic-only solutions at pH 9. Their adsorption capacities were further recognised by the adsorption tests conducted in simulated process waters. The ability to remove As (III) is of particular importance as it is harder to remove it from alkaline solutions. The magnetic cores allow simple and efficient magnetic recovery of the As-loaded nanoparticles.

Jan 1, 2017

By T. Newton, G. A. Bezuidenhout, P. J. Tauetsile, F. Trask

The technology to selectively leach gold, silver and base metals from ores, concentrates, and wastes, using an alkaline glycine solution, has initiated significant interest in using the new technology in various environments such as in-situ, in-place, dump, heap, and vat and agitated tank leaching. It has been shown that glycine acts synergistically with a number of other lixiviants to lower the net consumption of the other lixiviants while allowing low cost glycine solution recovery. Glycine is a non-toxic, stable, environmentally benign reagent that is available in bulk industrial quantities. It has the ability to dissolve most copper oxide and sulfide minerals, as well as native copper, whilst not interacting with acid consuming gangue nor dissolving iron and various or ubiquitous gangue elements. It acts synergistically with small amounts of cyanide to leach gold-copper ores at leach rates higher than either glycine or cyanide on their own, while significantly reducing cyanide consumption and eliminating detoxification requirements. The leaching behaviour of various glycine based systems will be reviewed, followed by the evaluation of the adsorption of gold onto activated carbon. Where the economics merit it, copper can be easily recovered using solvent extraction or sulfide precipitation.

Jan 1, 2017

By Joey R. Kish, Shooka Mahboubi, Hatem S. Zurob, Gianluigi A. Botton

The kinetics of the Cr2O3-based scale oxidation and volatilization were studied in the presence of water vapour (H2O). A commercial Cr2O3-based scale forming Type 310S stainless steel was examined at the ambient pressure (0.1 MPa) and 550ºC in relatively low and high H2O containing environments of air- 10% H2O and air- 70% H2O, respectively. The increase in the partial pressure of H2O (pH2O) from 10% to 70% resulted in transition of the oxidation and volatilization kinetics from the parabolic rate law for air-10% H2O to the paralinear rate law for air-70% H2O. The kinetics transition was attributed to the increase in the Cr loss rate from the base scale after coupons exposure in air- 70% H2O. The significant role of the Mn alloying element in the base scale protectiveness was also discussed in the context of the Cr2O3-based scale stability.

Jan 1, 2017

By Z. D. Hora

Air hough diatomite is known in many parrs of British Columbia, deposirs of mineable size have only been found in the area between Kam/oops and Quesnel in the sourh-cenrral parr of rhe province. Ar Quesnel, commercial producrion has continued since 1950 from diatomite lenses up ro 35m rhick. OCCURRENCES of diatomite are reported from many parts of British Columbia, but deposits of mineable size are known only from the area between Kamloops and Quesnel. Only Quesnel deposits have yet reached the production stage. Commercial production dates back to 1950, and up until 1979 approximately 22,700 tonnes of diatomite had been produced. Most extracted diatomite was processed until 1980 by Crownite Industrial Minerals Limited in Quesnel to produce an oil absorbent and animal bedding. Smaller shipments are used to make insulating bricks on the lower mainland. Deposits near Quesnel extend 40 km along the western bank of the Fraser River from Quesnel to Alexandria; most production has come from Lots o. 6132 and 906. Di atomite is present as discontinuous lenses up to 35 m thick. Diatomite beds Industrial Minerals in Canada are of Upper Miocene age and are overlain by plateau basalts. Diatomite consists almost exclusively of Melosira granulara diatoms that are usually very small and mixed with variable amounts of clay, ilt and volcanic ash. In recent years, extensive beds of diatomite were identified near the confluence of the Chilcotin and Fraser rivers. Diatomite in this locale is a part o f the Upper Miocene to Pliocene Chilcotin Group of sedimentary rocks that are overlain by olivine basalt and related luffs. A deposit near Red Lake is situated 50 km northwest of Kamloops. Diatomite beds occur in the Tranquille Series of Eocene age and are similar in composition to those in the Quesnel area. The Red Lake deposit is abo ut 4 m thick but its areal extent is only a few tens of hectares.

Jan 1, 1984

By L. Voisin, E. Díaz, V. Montenegro, W. Kracht

Grinding media is of great concern in the mining industry mainly because its consumption represents an important part of the costs during mineral processing and consequently, of the total mining business OPEX. In addition, grinding media consumption impacts directly on flotation performance through negative contamination by corrosion, affecting the pulp chemical potential, complicating the understanding and control of the process, as galvanic interactions between mineral species also occur. In addition, during the process there is also a physical consumption of the grinding media through erosion and impact. In both cases, mineralogy has an important role because pulp abrasion power, chemical reactivity, rheology, hardness and other variables depend on the minerals contained in the pulp and their interactions. In the present study, a geometallurgical and phenomenological model, which describes the grinding media consumption and its relationship with mineral hardness expressed by Bond Work Index, was obtained based on advanced mineral characterization techniques such as Hylogger3TM, X-ray diffraction, X-ray fluorescence and experimental grinding tests using a laboratory mill applied on Chilean copper pulps. The results obtained show that pH has an important effect on grinding media consumption, because corrosion varies with hydrogen ions availability. Also, mineral hardness depends on mineralogical composition, but textural analysis must be performed to have a better description of this property. Finally, minerals present in a sample define the grinding media consumption mechanism, because a sample with harder minerals and a greater value of Bond Work index is capable of protecting grinding media from impact wear, while a sample with lower hardness but with a big sulfide minerals content would be more aggressive with grinding media because corrosion is more important in this case. The geometallurgical model obtained is capable to relate the grinding time, mineral hardness, content of sulfide minerals and grinding pH to estimate the grinding media consumption.

Jan 1, 2017

By Z. D. Hora

Traditionally, industrial minerals in British Columbia comprise about 10 per cent of the combined value of mineral, coal, petroleum and natural gas production. Over the years a wide variety of industrial minerals have been produced in British Columbia, often with a different level of marketing success. For some products such as building stone, common brick or expanded shale, once strong demand gradually disappeared; for others such as asbestos and barite, new discoveries or new industrial activities created demand and new markets. For yet other minerals such as fluorite, talc and perlite, wider use has been prevented by the small size, poor quality or remote locations of the deposits. Bentonite (1926 to 1944-as a by-product from coal mines) Building stone (intermittently since the mid-1800s) Chromite (1918 and 1929) Over the past years, the list of industrial minerals produced has been expanded to include several new commodities: glassgrade silica sand, magnesite, pumice and silica for ferrosilicon and silicon carbide manufacture.

Jan 1, 1984

By S. C. Ells

Introduction An investigation of the bituminous sands of Alberta was begun by the Mines Branch, Department of Mines, in 1913. This investigation was interrupted during the period 1916-19, but was resumed in 1920. Work completed in October 1924 has included detailed topographical surveys of extensive areas, examination and sampling of principal outcrops, the mining of trial shipments, laying of demonstration pavements, and a study of methods adapted to the recovery of hydrocarbons from the crude bituminous sand. Bituminous sand consists, for the most part, of clear quartz grains, cemented together by petroleum residuum or bitumen. In form the quartz grains are most irregular, varying from sharply angular to smooth, waterworn shapes. The bitumen has a specific gravity of 1.018 and has a penetration of 9.00 mm. (77° F. 100 grams 1 sec.). The percentage of bitumen associated with the sand varies from 5 to 25 per cent. A large tonnage is available in which the percentage of bitqmen is 15 per cent or over. Production Up to the present time, production has been restricted to requirements for experimental .and demonstration work. The total quantity shipped for such purposes has not exceeded 750 tons.

Jan 1, 1925

By Raj Thamburaj

"Over the last few decades, the emphasis on affordability and reduced cost of ownership has necessitated the development of innovative processes to carry out repairs in aero engine components. Conventional weld and braze repairs have evolved into advanced, sophisticated processes using state of the art knowledge in lasers, robotics and materials technology. This paper illustrates past and present scenarios in an attempt to illustrate progress that has been made in this area. The problems encountered in the past have been detailed along with the solutions that have been developed and commercially implemented to address these issues. Apart from technical progress, this presentation also addresses the progress made in business approaches and in Certification/Regulatory issues surrounding aero engine repair. Progress in Technology Repair technologies have also been the embryo from which new and revolutionary manufacturing technologies have evolved as well. Electron Beam Free Forming and LENS are examples of how a completely new manufacturing concept can evolve what was originally only a process to join metals. The current and future potential of these spin offs is discussed providing examples of application. While several problems have been solved over time with the implementation of advanced repair technologies, the demands of the industry have created new challenges. The paper describes these issues, outlines potential solutions and discusses the future of repair technologies in terms of the far reaching influence it is sure to have in design, manufacturing, maintenance management and life extension. Progress in Business Trends.Business approaches to repair and maintenance have also gone through considerable change with the introduction of ""Power by the Hour"" and other similar arrangements between the companies responsible for engine overhaul and the end-users. Program Based Logistics (PBL) is yet another innovation to provide a win-win situation for the repair service provider and the end user. This paper traces the development of these business initiatives and highlights successful applications. Progress in Repair Certification, Regulatory Issues.Understanding of the issues surrounding certification of repairs has also evolved with time and regulatory issues have been clarified considerably. Procedures for analysis and testing are much clearer and ""Check Lists"" are being drafted for certifying repairs on various engine components. The PMA phenomenon has added yet another dimension to the issues regarding certification and these are discussed as well."

Jan 1, 2010

By Larry B. Smith

"Feasibility studies are the means by which mineral reserves are established prior to financing a project. However, guidelines are generally lacking for the content, data quality and accuracy of these studies. Regulators take a principle-based rather than prescriptive approach to the content of studies and look to the industry to define study content. Professional organizations, engineering firms and mining companies must eventually establish guidelines and best practices for this work. Most likely these will draw on standards or “stage gates” that have been developed by major mining houses and engineering firms. Engineering studies must: 1.,Define optimal mining and processing methods, production rates, infrastructure, product sales, environmental management and risk mitigation. 2.,Increase confidence in resources, reserves, production plans, processing performance, infrastructure design, environmental management, permitting, capital and operating costs, and financial performance to support financing. 3.,Provide engineering designs suitable for accurate cost estimates. 4.,Develop project execution plans with sufficient confidence that project delays and cost overruns will not occur. Conceptual (scoping, preliminary assessment) Establish the principal characteristics of the project from the geology, resources, metallurgy and development constraints. Assess different approaches to mining and processing. Identify project execution requirements. Test project viability with economic analyses. Recommend additional work to increase the confidence in geology, resources, metallurgical performance, infrastructure, operating and capital costs, environmental conditions and permitting to allow selection of the best development options."

Jan 1, 2003

By Abhilash

Uranium is conventionally extracted using a process that employs strong acid (H2SO4) and an oxidant (MnO2) as leaching agents. This method often creates environmental problems, requires large amounts of energy, and involves a complex operational plant. It is not, however, economically attractive to extract uranium from low-grade ores by chemical leaching. Because the content of U3O8 in the Indian ore is usually below 0.1% by weight, it is necessary to develop an alternative process to enable the efficient and economic recovery of uranium. Uranium ore from the Narwapahar mines, UCIL is a type of vein deposit found in India, which accounts for ~54% in India. The ore (0.047% U3O8), though of Singhbhum area, possess exceptionally different mineralogy due to presence of some refractory minerals and richness of apatite (5%) resulting in a maximum 78% recovery through conventional processing at UCIL, with a very high consumption of sulfuric acid and pyrolusite, besides possible loss of uranium as uranium phosphate. To avoid usage of environmentally non-benign oxidants, remediation of influence of phosphates, and improve the overall process output of uranium; an alternate extraction technology using microbial isolate(s) is worthwhile exploring and the same is presented in the paper. The microbial isolate enriched with Acidithiobacillus ferrooxidans grown from source mine water was employed for bio-leaching of uranium while varying pH, pulp density (PD), particle size, etc. On varying pH at 35oC using 20%(w/v) PD and <75µm particle size, 83.5% and 78% uranium bio-recovery were observed at 1.7 and 2.0 pH in 40 days against maximum recovery of 46% and 41% metal in control experiments respectively. Whereas, it was observed that grinding of ore to finer size actually helped dissolution of uranium. Finer size particles (<45µm) gave a maximum biorecovery of 93% in 40days at 10%(w/v) PD, 1.7 pH and 35oC. The bio-recovery of uranium fell down from 93% to 82.73% and 60% on increasing the pulp density from 10% to 20% and 30% respectively for particles of <45µm size. The higher uranium dissolution during bioleaching at 1.7pH can be correlated with increase in redox potential from 433 mV to 664mV in 40 days.

Aug 1, 2010

By R. R. Irrinki

Abstract -The Key Anacon deposit consists of four sulfide zones called, from south to north : Key Anacon No. 1, Key Anacon No. 2, Key Anacon No. 3, and Key Anacon Copper Zone. Massive sulfides of zones 1, 2, and 3 are underlain by rocks correlated with the Nepisiguit Falls Formation and are overlain by matie volcanic rocks correlative with the Boucher Brook Formation. In contrast to zones 1, 2, and 3, narrow northwesterly-trend.ing, copper-rich fracture zones occur within the Patrick Brook Formation. Sulfides in zone 2 occur as three mineralogical associations, namely: pyrite-chalcopyrite, pyrite-sphalerite-galerta, and pyrrhotite-sphalerite-galerta. The distribution of lithologies and en-echelon patterns of the three sulfide lenses of Key Anacon No. 2 zone are the result of F1 and F2 folding. Zone 2 is the most promising economically, with proven reserves of 1.11 million tonnes grading 0.2207o Cu, 3.47% Pb, 8.41% Zn, and 96 g/t Ag; the zone is open below a depth of 427 m.

Jan 1, 1992

By Robert Halupka

The industrial minerals sector represents a broad range of products involving a variety of technologies serving a diversity of markets and end uses. Unit values of products vary widely, reflecting the peculiarities of each product/market sector. Generalizations are therefore understandably difficult to make and borrowers may need to take extra time to "educate" lenders on the key aspects of their business and industry sub-sector. This paper will examine the factors and the thinking that lenders apply when considering financing proposals to companies in the industrial minerals sector. If you understand the lender's perspective and their concerns, then you can make better use of your own time and resources when arranging financing for your company or project.

Jan 1, 2001

By Ed Labelle, Terry Overton, Gary Bell

"LocationThe Miller Minerals lime and limestone production facility is located in the Temiskaming district of Ontario at Hailey bury on the west shore of Lake Temiskaming. Located less than 300 km from Sudbury, Timmins, Rouyn-Noranda and Val d'Or, the plant is very well situated to market products to the mining, pulp and paper, and environmental industries. Being located a few kilometres from the Trans-Canada Highway and the Ontario Northland Railway adds to transportation efficiencies.ProductsAt Miller Minerals, two principal products in various sizes are produced, which are limestone (CaC03) and quicklime (CaO).HistoryProduction of limestone products began in 1979 at this quarry site. During the 1980s, limestone products were marketed to a variety of applications for mining, forestry, environmental and agriculture applications. In 1990, the production of quicklime products began, following the commissioning of an Italian-designed vertical shaft calcining plant. During the 1990s, both quicklime and limestone products were produced to meet the customers' demands.From the quarry's conception until 1992, the operation was owned and operated by Dymond Clay Products. In 1992, it was purchased by Miller Paving Ltd. of Markham, Ontario, and became a key part of the company's industrial minerals sector of business. Other Miller interests include dolomite, cement, paving materials and waste management."

Jan 1, 2000

By Bradley Stoughton

The magnetic oxide of iron, F eO4 , contains a theoretically larger amount of iron ( 72.4 per cent.) than any other commercial ore. It is probable that it has originated in many cases by the prolonged exposure of the hydrated oxide, ZF e20 a + 3H20 to heat and pressure which converts it first into hematite, F e20 3, and then into magnetite. It would thus appear as if nature had already done part of the work of removing all the oxygen and that magnetite should be relatively easy to reduce. That it is, in fact, less reducible than either limonite or hematite, is due chiefly to its dense and compact physical structure, which makes it less pervious to the furnace gases, and also to its characteristic action in resisting crushing to a uniform size, with consequent irregularity in reducing conditions within the furnace. The net result is that the magnetic oxide requires more fuel and more time for its reduction in the blast-furnace than any other iron ore of similar iron content and physical condition. There is another very important reason why the smelting of magnetite is more costly than that of hematite, and its treatment viewed with a great deal of adverse prejudice by blast furnace operators, namely, that magnetite decreases the proportion of heat developed by the fuel in the stack of the furnace, and increases the already excessive heat requirements of the heart.

Jan 1, 1924

By Victor F. Hollister

Although none of the deposits discovered to date are of commercial interest, significant Frasch or sedimentary sulphur deposits occur in Nova Scotia in Upper Mississippian Windsor Group evaporites. The evaporite sequence contains anyhdrite and is overlain by impervious shales. It also is •mderlain by locally petrolijerous formations that are potential hydrocarbon sources for reaction with anhydrite to produce sulphur. As well, stratigraphic and structural traps are known to exist in the Mississippian beds. Thus, all requisites for sedimentary sulphur genesis are present. Available hydrocarbon sources are numerous but small; resultant sulphur deposits therefore are probably also small. Evidence suggests, however, that sulphur deposition is not yet complete.

Jan 1, 1984