Search Documents

By A. Boehm

"For recycling LD slag into the steel making process, the phosphorous containing calcium silcate phases have to be removed from iron oxide phases. One possible technical solution could be magnetic separation in a wide range of susceptibilities from ferromagnetic to paramagnetic. To check the feasibility of magnetic separation the distribution of the magnetic susceptibility in size classes as well as the liberation of the phosphorous containing phase were evaluated by a new method combining two dimensional physical property analysis with QEMSCAN analysis. The particle size classes of energy controlled comminution products were subdivided into fractions of defined magnetic susceptibility using a hand magnet of well known field properties (pick up method). On the one hand the susceptibility classes were wet assayed on the other hand analyzed by QEMSCAN followed by data evaluation using iDiscover 5.3.1(FEI), which was adapted to the data structure of two physical properties (size and magnetic mass susceptibility). The results allow the comparison of mass based (3D) cumulative distribution of grades from the wet assays with the area based (2D) distribution from QEMSCAN analysis, in order to control a systematic (size dependent) stereological error for this special type of material. As the physical separation property forms a crucial parameter the results from the liberation analysis by QEMSCAN can be interpreted more profound with respect to an expectable separation result. Once the various mineral compositions of the particles are assigned to the physical properties the Henry Reinhardt chart serves to predict the best possible separation result and thus the feasibility of a separation technique.INTRODUCTIONThe two Austrian steel plants operated by voestalpine AG produce about 650,000 t (voestalpine 2014) of LD slag in the course of steel production from pig iron according to the basic oxygen process blowing oxygen in the converter by an oxygen lance. The process is also known as the Linz Donawitz (LD) steelmaking process. By the addition of lime (CaO), carbon, phosphorus, silica, manganese and sulfur, which are present in the molten pig iron, shall be oxidized and bound in the slag either as oxide or silicate phases, or leave the slag in the gaseous phase (CO). The average chemical composition of the investigated LD slag is given in table 1."

Jan 1, 2016

By A. Ghahreman, M. Oliazadeh

"Heap leaching is an attractive process for low grade deposits where the metal content of ore does not justify the high cost of milling and agitated leaching. In general, the heap leaching capital cost is low, construction is rapid, and production costs are low. The primary disadvantage of heap leaching is low recoveries (typically 65% of agitated leach recovery); thus, recovery improvements could convert more lower-grade deposits into minable reserves. This will also allow to process primary sulfide ores and result in a dramatic expansion of the technology, as ~80% of total ore types are sulfidic in nature. The old gold operations tailings are another massive source of low-grade gold material that can be retreated by the heap leach process. The major parameters affecting the recovery rates are ore characteristics (mineralogy, particles size of metal and host minerals, ore permeability), and operational conditions (segregation of ore, compaction, leach cycle time, lift height, and solution application rates). The design of a percolation leach process is based on a limited number of coarse ore bottle roll and/or column tests under ideal conditions. The economics of the projects and engineering design of the process facilities are developed based on the bench scale test work results and the application of the conventional engineering scale up factors. This paper will deal with the parameters affecting the HL efficiencies and focus on the potential improvement of gold heap leach recoveries. This would include design of heap leach operation and evaluation of processes such as fine crushing and bioleaching.INTRODUCTION Gold heap leaching is a hydrometallurgical process designed to treat amenable low-grade gold ores that contain typically 0.5 to 1.5 g/t gold (Marsden and House, 2006; Wong Wai Leong and Mujumdar, 2010). Ore is stacked by various types of equipment on an impermeable barrier, and a sodium cyanide solution is applied to the surface of the stacked ore. Gold, silver, and other metals contained in the ore are dissolved to various degrees by the cyanide application, as it percolates downward through the stack of the ore. The pregnant leach solution (PLS) is then collected at the bottom of the heap. The PLS is then sent to the gold recovery plant where the metals are extracted. The barren leach solution (BLS) is then reapplied to the top of the pad. Ore is placed on a pad or previously leached lift by various means, including ramp conveyor belts, radial-arm and self-leveling stackers, and trucks. Once trucks are used to construct the pads, the pad can be compacted and hence the pad should be graded and ripped or scarified (roughened up) with wheeled or tracked equipment to produce shallow cuts to increase surface area exposure to the leachate."

Jan 1, 2019

By Neil Campbell

"The Pine Point area is on the south shore of Great Slave Lake, 510 air miles north of Edmonton and J JO miles south of Yellowknife, N.W.T. The occurrence there of lead and zinc was reported in J 899 by R. Bell (5) of the Geological Survey of Canada, and in the following years several claims were staked and some prospecting was done. In 1928 Atlas Exploration Co. took over the property containing the discovery occurrences. In 1929 The Consolidated Mining and Smelting Company of Canada Ltd. (""Cominco"") and Ventures Ltd. participated with Atlas in forming the Northern Lead-Zinc Co., which, under the direction of J. M. Bell, carried out 24,499 feet of drilling in the discovery and surrounding areas. Two shafts and many surface pits were also sunk. This work showed that the discovery deposits contain about 500,000 tons of lead-zinc ore, but no new orebody was found.In 1936 D. F. Kidd (11) drew attention to the highly significant space relations between the base-metal discoveries at Pine Point and the projections of certain major Precambrian faults mapped earlier by C. H. Stockwell. Geological work by Cominco in 1940 and subsequent years suggested the presence of mineable deposits within a belt of land including part of the area of earlier field work and extending far beyond it. Between 1946 and 1954 exploration financed by Cominco and Ventures Ltd. included 182,950 feet of diamond drilling, 383 feet of sinking, and 240 feet of drifting, raising, and crosscutting. This work was successful in finding substantial quantities of new ore in places where bedrock is completely concealed.The topography is one of low relief, characterized in many places by swampy muskeg and shallow, marl-bottomed ponds. The area where ore has been found is generally higher ground which, though not well drained, is comparatively dry. It is also marked by raised beaches and a few sand dunes overgrown by small spruce and pine. Bedrock is generally overlain by a variable thickness of hard, glacial boulder clay. This in turn is covered by silt, sand, and gravel, probably deposited from the waters of Great Slave Lake, which formerly extended many miles beyond its present southern shore."

Jan 1, 1949

By M. du Plessis, D. F. Malan

"Crush pillars are designed to be in a crushed state whilst being formed at the mining face. The residual stress state of these failed pillars provides a local support function in mining stopes and is used in the majority of the intermediate depth South African platinum mines. On mines utilising crush pillars, the pillar dimensions are selected to achieve a width to height ratio of approximately two. This is not achieved in most cases as a result of practical mining problems and poor pillar-cutting discipline. Furthermore, pillar dimensions are seldom adjusted to compensate for the various factors governing crush pillar behaviour. The pillars should, however, be in a crushed state whilst being formed or whilst still in close proximity to the mining face to prevent potential damaging seismicity.An underground investigation was conducted into the behaviour of the crush pillars in a trial site on the Merensky Reef at Lonmin Plc. The aim of this investigation was to examine the mechanism of pillar crushing and the related rock mass behaviour. The underground test results and pillar behaviour are compared to a limit equilibrium model to investigate if the model provides a useful approximation of the behaviour of the crush pillars. This paper details some of the preliminary findings.INTRODUCTIONOn most mining operations, the design of crush pillars is based on trial and error. As the pillar strength is unknown, the pillar sizes are adjusted to obtain the correct behaviour. Crush pillar dimensions are generally selected to give a width to height ratio (w:h) of approximately 2:1, (Ryder and Jager, 2002). Several factors affect the behaviour of the crush pillars and in many cases satisfactory pillar crushing is not achieved. This results in a seismic hazard in many of the mines using crush pillars. If pillar crushing is not initiated whilst the pillar is being formed at the mining face, as the mining face advances and the pillars move to the back area of a stope, some pillars may burst while oversized pillars may punch into the footwall. If pillars are designed in such a way that they are fractured during cutting by the face abutment stresses so that the pillars will already have yielded and reached their residual strength, further compression of the pillars will be associated with an increase in load and stability will be ensured, (Ozbay and Roberts, 1988). The stiffness of the strata must therefore be greater than the post-peak stiffness of the pillar (Figure 1) or violent pillar failure and hanging wall instability will occur. The pillar design should be aimed at determining pillar dimensions for which the post-peak curve of the pillar is as flat as possible."

Jan 1, 2015

By K. P. Wright

THREE OF the gold mines in the Red Lake Camp operates fluid bed roasters in their milling circuits. The mines are Campbell Red Lake, Cochenour Willans, and Dickenson. The roasters are used for the autogenous roasting of a flotation concentrate for subsequent gold recovery by cyanidation. Cochenour and Dickenson operate single stage reactors, whilst Campbell use a two-stage system. Ore treated by the mines is similar in that the major part of the gold is associated with arsenopyrite. Other sulphides present are pyrite, pyrrhotite, stibnite and sphalerite. Gangue minerals are mainly quartz, with carbonates and talc. Mineralization is, for the most part, extremely fine, and there is intimate association between sulphides and quartz, so much so, th at a picked specimen of apparently massive arsenopyrite will frequently contain as much as 80 per cent gangue. Gold recovery by straight cyanidation on this type of ore would not be higher than 80 per cent and

Jan 1, 1961

By A. E. Cameron

The theory of atomic distribution of the stranger atoms in the space lattice of the solvent metal has been well developed by Rosenhain. It has long been known that the addition of one metal to another to form a solid solution increases the strength and hardness of the solvent metal. This increase is practically proportional to the amount of added substance up to the limit of solid solubility. To account for this increase in hardness and strength, Rosenhain assumes that the stranger atoms occupy positions on the solvent metal space lattice. Atomic attractions about the stranger atoms will not be the same as in the case of the pure metal, and there will thus be a disturbance of the orderly arrangement of the atoms on the space lattice, or a distortion of the lattice. Such a disturbance would interfere with the ease of slip along the planes and would thus tend to promote strength and hardness. Rosenhain notes that not only may there be a local disturbance of the lattice about the stranger atom but there may well be also a measurable change in the dimensions of the lattice as a whole. The relative amounts of local and general distortion of the lattice will depend upon the nature of the lattice itself. As Rosenhain says, "If the lattice is comparatively soft and flexible the distortion is likely to be largely local. In a stiff lattice, however, local distortion will be resisted and there will be a correspondingly increased general distortion."

Jan 1, 1927

By Peter Rubie

For many years, optimising the relining of hard rock grinding mills has been complicated by: ?? the large number of variables; ?? the low frequency of relines (slow feedback loop); ?? the potential economic risk associated with some changes. A technology that has its roots in the automotive manufacturing industry is being utilised to construct a statistically accurate, configurable, and dynamic simulation of the mill relining process. The effects of various mechanisation and process changes can be rapidly modelled and compared. This technology will provide mill maintenance managers and contract relining companies with the opportunity to benchmark current performance against world?s best practice. It will also provide an opportunity for concentrator plant designers and mill manufacturers to plan for maximum plant efficiency, by designing an infrastructure and equipment combination that maximises annual plant availability. This simulation tool and its associated data set, has been developed using recent grinding mill performance data from mills of varying dimensions, liner configurations, mill relining equipment, operator and tool variables. The simulation will provide an output that the various stakeholders can utilise to make optimal decisions within the given financial, physical and technological constraints of the individual concentrator plant.

Jan 1, 2012

"Beneficiation of low grade ores is the process of increasing the grade of a mineral through unit operations that remove and separate the waste (or gangue) material from the valuable mineral that can then be used for further processing or direct use. Important factors when deciding upon a beneficiation program are the feed grade, mass yield and the metal recovery. As lower grade ores are being processed beneficiation is a critical process. How predictive is laboratory test work for “as built” operating projects? Beneficiation includes all or some of the available unit operations to produce a beneficiation flow sheet i.e. associated unit operations including but not limited to optical sorting, radiometric sorting, crushing and screening, coarse cobbing, jigging, dense media separation (DMS), spirals, magnetic separation, flotation, thickening, filtering and drying. Reference to specific projects and the approach developed in formulating a beneficiation flow sheet and a comparison of difficult and simple beneficiation flow sheets are cited. INTRODUCTIONReserves of high-grade iron ores are reducing all over the world, at an alarming rate, over the years as a result of the rapid increase in demand for steel particularly from Japan and then China. The recovery of mineral value from the low-grade ores using present technology is more expensive than DSO ores due to high energy and capital costs. Beneficiation is defined as a variety of processes whereby extracted ore from mining is reduced to particles that can be separated into mineral and waste.Various physical properties of an ore can be exploited to separate a low grade fraction including variation in hardness, density, reflectance, conductivity and magnetism.""Beneficiation"" of iron ores includes concentration, generally by physical removal of unwanted gangue. Also considered beneficiation is the regulation of product size, or other steps such as agglomeration to improve its chemical or physical characteristics prior to smelting."

Jan 1, 2012

By K. M. Sarkar

"In many plant trial s(1,2) it has been proven that very small amounts (10 to 20 ppm) of uranium dissolved in mine water can be effectively recovered by the use of ion exchange resins and this uranium recovery has many advantages. In this paper an economic analysis at different levels of uranium contamination and at different market prices of uranium are described.For this study an operating mine-mill complex with a sulphuric acid leach circuit, followed by solvent extraction (SX) process, is considered, where contaminated mine water is available in excess of process requirements. lt is further assumed that the sulphuric acid eluant containing uranium would be mixed with the mill pregnant liquor stream that proceeds to the SX plant for final uranium recovery.Recovery by Ion ExchangeMine water, in this study, is defined as the water coming from the underground mine, or mine pits, and the run-off water from stockpiles, mine shops, crushing plant , washdown areas, etc.In nature, uranium mainly occurs in two stages; reduced (tetravalent) and oxidized (hexavalent) . The oxidation of sulphides present in the orebody often causes the presence of S04- and acidity in mine water, and this acidic water readily dissolves U+6 part of the depo sit. The react ion between hexavalent uranium, which is dissolved in water as U02+ 2 cation and S04 producing uranyl sulph ate as,"

Jan 1, 1984

By Brian K. Ayres

Inco Limited, Ontario Division is currently in the process of decommissioning the Whistle Mine site located near Sudbury, Ontario, Canada. The most significant component of site decommissioning involved relocating approximately 6.4 million tonnes of acid-generating waste rock to the open pit from two adjacent stockpiles. An engineered cover system was designed for the backfilled pit to reduce the long-term production of acid rock drainage. Geochemical modelling was conducted to assess the effectiveness of various cover options on the longterm water quality of the backfilled pit. Results obtained from performance monitoring of cover system field trials at the site and estimated full-scale construction costs were used to select an appropriate material for the cover system barrier layer. The two-dimensional soil-atmosphere model VADOSE/W was used to develop a calibrated model of covered waste rock based on field data obtained from the cover trials, which was subsequently used to predict net percolation and oxygen ingress through various cover system alternatives for site-specific climate conditions. Erosion and landform evolution numerical modelling was completed to assist in designing the runoff management system and final landform for the pit cover system. The potential impact of various physical, chemical and biological processes on the sustainable performance of the pit cover system was also considered in the design process. This paper provides an overview of the design and construction of the backfilled pit cover system.

Apr 1, 2005

By A. Musschoot

"The paper will review general types and designs of vibratory feeders, describing briefly the design features and characteristics that apply to the application of specific types. Control considerations for selecting types will be dis• cussed, such as fixed or adjustable, manual or automatic, individual or multiple bank, and process requirements. Design parameters for hopper openings and installation geometry will be discussed, including consideration of material size distribution, segregation, moisture content and other characteristics, based on practical applications and experience as well as theory. Pan designs and the selection of pan materials will also be discussed with reference to wear, corrosion, impact and practical economic factors."

Jan 1, 1972

"Some of the tools developed for the processing of nickel laterite ore by resin-in-pulp (RIP) may be applicable to the remediation of metalliferous mine drainage (MMD). In both cases, recovery of metal value and production of a stable waste stream appropriate for long term storage is desired. MMD typically has the additional challenge of management of toxic low-value metals. Seen in this light, innovations in RIP reactor configuration, selective elution strategies and novel synthetic ion exchange resins become useful tools for taking on the MMD challenge in a way that maximizes both environmental and economic benefit. INTRODUCTIONAcid mine drainage (AMD) is a common problem in any country with significant past mining activity. When sulphide containing minerals, tailings or slag are exposed to water, oxygen and sulphur oxidizing bacteria, AMD will result. Abundant and reactive iron sulphide minerals leach first, providing acidity and the ferrous/ferric couple that can enhance the oxidation kinetics of other minerals. If this runoff contacts encounters acid consuming carbonates or silicates, the acidity may be neutralized, but certain heavy metals remain in solution and can continue to be an environmental hazard (Gray, 1997). For this reason, the remainder of this paper will refer to the broader term metalliferous mine drainage (MMD) rather than acid mine drainage. In either case, such drainage, containing high heavy metal concentrations and often significant acidity, is toxic to aquatic life and can lead to significant damage to ecosystems and to public watercourses. MMD is a problem most commonly associated with now defunct sulphide mineral mines, but similarly toxic streams can result from many types of waste, such as poorly stabilized leach tailings, slag heaps, and coal flotation tailings (Johnson and Hallberg, 2005; Lee et al., 2002; Sainz et al., 2002; Schüring et al., 1997). In any case, the management and remediation of MMD is an important ongoing problem for the resource industry, particularly for the many mines in Canada closed before the advent of more stringent environmental standards. MMD remediation represents a significant long term expense for the resource industry. Multi-disciplinary efforts to understand and mitigate this problem range from creation of artificial wetlands (Poulin and Lawrence, 1996; Sheoran and Sheoran, 2006) to sophisticated biochemical reactors and precipitation processes (Hatami, 2010). Certain remediation technologies such as ion exchange offer methods to make a saleable product by recovering valuable dissolved metals. This paper will show how these technologies can help defray the cost of remediation, and offer potential to turn a dangerous waste stream into a useful product."

Jan 1, 2012

By J. C. Mitcheson

Mr. President, Mr. Mayor, Ladies & Gentlemen: IT GIVES ME great pleasure to have the opportunity, today, to speak on behalf of all the constituent. bodies of the Common-wealth Council of Mining and Metallurgical Institutions. For the past month we delegates have been right royally entertained across the length and breadth of Canada by Provincial Governments, City Councils, and other equally generous public organizations and private corporations. On this occasion, however, the President of The Canadian Institute of Mining and Metallurgy, our good friend Dr. H. J. Fraser, has been our host at the enjoyable reception preceding this Institute Luncheon, which luncheon was sponsored by our official host, The Canadian Institute of Mining and Metallurgy, one of our .constituent bodies.

Jan 1, 1957

By W. N. B. Armstrong

CORROSION of metals, for the purpose of this talk, may be divided into two general classes, namely, atmospheric and chemical. Atmospheric corrosion is caused by the natural agents -water, air, salt, and temperature -as well as by the agents arising from industrial operations which pollute the atmosphere. Chemical corrosion affects metals in refineries and chemical plants where severe conditions exist due to .acids, alkalies, salts, solvents, gases, ?steam, etc. A special condition is encountered on road equipment and motor vehicles due to the large amounts of corrosive salts which are used on our roads in the winter. Exposure to corrosive conditions such as those referred to above causes metal to be destroyed and, therefore, it has to be protected. The non-metallic or organic coatings used to protect the metal are themselves destroyed ultimately by these same conditions. Since all types of organic coatings do not have the same kind and degree of resistance to degradation, a particular kind of -coating must be used for a particular set of conditions in order to obtain the maximum benefit. In ?addition to the above mentioned agents, organic coatings are degraded ?by sun-light, which is probably the severest single factor in the breakdown of organic coatings exposed outdoors. We can divide organic coatings, in a general way, into the following classes: (1) Conventional coatings, and (2) Special coatings.

Jan 1, 1958

By W. H. Zieman

NORMAN WEISS, Milling Engineer, American Smelting• and Refining Company: The subject of the Forum on Rod and Ball Mill Liners is very fascinating, and there is no end of discussion when operators get together on grinding. However, the hypotheses and suppositions easily outrun the facts, especially when we •consider the inaccuracy of many reported observations. Still surprisingly small is the number of concentrators even reasonably well equipped to measure power consumption of each grinding mill, together with running time, so that data on this tangible factor, at least, can be obtained with precision. While the more elaborate devices of this nature, producing for each 24-hour period the total power consumption, average kilowatt hours per hour, short-term demand chart, instantaneous demand, and print-out, may cost in the neighbourhood of $2,500 per mill and may be difficult to justify, the combination of an ammeter, watthour meter, and running-time meter will cost only a few hundred dollars, so there appears to be little reason not to in-stall them in view of their numerous advantages.

Jan 1, 1959

By Shek N. Lau, Nicola Samman

"Enclosed gear cases on board heavy mining equipment have traditionally been lubricated with regular heavy duty gear oils. However, equipment manufacturers, have recommended the use of an ISO-1000 gear oil for this application to ensure adequate lubricant film strength, especially at the higher end of the working temperature range. The majority of these ISO-1000 gear oils are based either on residual/asphaltic oil or synthetics, primarily higher viscosity polyalphaolefins. Although the performance of these lubricants has been satisfactory, they suffered other shortcomings that equipment users have lived with over the years.The major requirement at the user’s mine was to provide lubrication for the shovel Hoist gear case. Within such a gear case design, the gears and the roller bearings, that have different lubrication requirements, are lubricated with the same lubricant. Several lubricants were used, light gear oils as well as the recommended ISO-1000 heavy gear oils. On the one hand, the lighter oils performed adequately for the lubrication of the bearings that formed part of the enclosed gear system. These lighter oils did not perform as well for the lubrication of the gears due to their lower viscosities, resulting in shorter gear servicelives.On the other hand, the ISO-1000 gear oils performed well for the lubrication of the gears, but were too viscous to creep into the bearing elements to lubricate them adequately, especially during the cold northern Canadian winters. This resulted in catastrophic bearing failures and secondary damages to the gears.The challenge, then, was to formulate a lubricant which met the 1000 cSt at 40°C viscosity requirement as stipulated by the equipment manufacturer, while satisfactorily lubricating the bearings at the full working temperature range. This was achieved by the development of a semi-fluid grease lubricant, which has proven in field trials to give adequate performance in this application for the lubrication of both the bearings and gears down to -40°C.This product met the equipment manufacturer’s performance criteria and resolved, to a large extent, leakage of the lubricant through seals experienced with the use of conventional and synthetic gear oils.Although the main performance criteria of the fluid was its capability to lubricate the “Hoist” gear case, it was also used during the field trial in other gear cases on board the shovel to test its full capabilities.This unusual alternative lubricant was field tested and evaluated for more than two years. Based on this assessment, the product was reformulated to improve its fluidity, slumpability and the settling of debris/wear metals to the bottom of the gear cases. This reformulated softer grade, a semi-fluid grease, has been performing satisfactorily for more than eight months and is still undergoing longer term assessment."

Jan 1, 1996

By D. P. Ziegler

Formulas relating economic optimum busbar cross sectional areas to busbar cost, electric price and financial parameters are reviewed and revised. Application of the formulas is illustrated with discussion of the appropriate choice of parameter values and the sensitivity of the optimum to the parameters. The extension of the single busbar concept to optimization of more complicated arrangements of bus for smelting pots is complicated by the constraint of obtaining a specified current distribution. An example problem illustrates the optimization of a section of a bus network containing a fork, with the imposed limitation of achieving a specified uniformity in the current. In cases where the current in the individual conductors may vary, Kelvin's law does not apply. Further extension of the technique to a full pot set of conductors poses additional problems which are discussed, but whose solution has not yet been accomplished. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By Neville Jordison

Indirect, gravity flow, heat exchangers have become a well established technology in mineral and metallurgical process plants. The technology is a conventional heat exchanger using high efficiency plates, with a free flowing bulk solid on one side of the exchanger and a fluid on the other side. This simple concept leads to many opportunities for achieving greater energy efficiencies in process plants. Indirect heat exchange is much more efficient than direct heat exchange using air such as in a fluid bed or rotary device. When air is used directly, large fans are required, it may also be necessary to chill the air, both high consumers of energy. By contrast, using water as the cooling medium requires only low horsepower pumps, typically only 10% of fan HP. Furthermore there are no stack emissions with the requirement for removal of dust or emissions. Indirect heat exchange also creates the opportunity to recover energy. This can work in two ways: energy can be recovered from a hot bulk solid, to heat pressurized hot water for steam generation or preheat air. Alternatively recovered energy from elsewhere in the plant in the form of hot water, steam, air or thermal oil can be used to preheat a bulk solid.

Jan 1, 2011

By A. Khan

The purpose of this paper is to demonstrate the value of identifying and optimizing throughput constraints by utilizing a Constraint Model. This will be achieved by first understanding the overall concept of Operational Excellence, Continuous Improvement and Theory of Constraints as practiced within Vale Canada Limited. Next, the value of utilizing a Constraint Model is demonstrated by primarily identifying constraints. The applications in utilizing Constraint Models will be demonstrated, including the primary benefit of identifying constraints. The remainder of the paper will focus on how to properly setup a Constraint Model using discrete simulation (regardless of simulation software). Benefits of understanding the severity of constraints and movement of the bottleneck will be recognized. The paper will conclude with the summary of real applications within Vale Canada Limited.

Aug 1, 2013

By J. S. De Lury

The metalliferous areas of Manitoba have been described in more or less detail. Since the descriptions were written some new prospects have come to light and considerable mining development has taken place in two or three localities. No attempt will be made in this paper to give an account of recent activities or to describe the several areas in detail. In a general way, geological conditions are similar in all metalliferous areas of the province, a similarity that invites a discussion of the prospects as a whole, the features that are common to all deposits and the reasons for their uniformity. Modern theories of metallogenesis have a direct bearing on such a discussion and an effort will be made to show their application.

Jan 1, 1925