Search Documents

By G. W. H. Norman

"The La Corne molybdenite-bearing veins, discovered in 1915, lie halfway between Amos and Val d'Or near the southwest corner of La Corne township, Abitibi county, Quebec. The Molybdenite Reduction Company, which carried on operations during 1927 to 1930, sank a 200-foot inclined shaft to develop the property and produced about 22 tons of concentrntes from a 30-ton mill during 1929. Hollinger Consolidated Gold Mines, Limited, carried on further underground exploration in 1930. The Molybdenite Corporation of Canada drilled a part of the property in 1938 to 1939 and produced 1 ton of concentrates in 1938. Wartime Metals operated the property from 1942 to July 15, 1945. At this time the mill was enlarged to treat 200 tons daily. Molybdenite Corporation of Canada since July 15th, 1945, have continued the operation of this property and have revised the mill flow-sheet in order to produce both a bismuth and a molybdenite concentrate.The production for the period 1942-1946 is as follows:Total molybdenite production from the mine in the 1942 to 1946 period was about 4,127,400 lb.The La Corne deposit occurs at the northwest contact of a small mass of biotite granite with biotite schist. The form and extent of the biotite granite mass is concealed by a wide sand plain that extends northwest and west from the deposit and overlies bed-rock except in four small outcrop areas. These are spaced 1,000 and 2,000 feet apart along a narrow strip extending 5,000 feet south from the mine. The outcrops suggest that the granite must be at least 1,500 feet wide and 3,000 feet long northeastward. Where exposed in the mine workings the contact dips 70°N.W., but is not a sharply defineable feature due to the presence of numerous granite dykes and tongues in a zone of biotite schist 100 feet wide along the margin of the granite. The biotite schist in the few outcrops that flank the north and south sides of the granite strikes northeast and dips 60° to 70° S.E."

Jan 1, 1954

By R. A. Lunceford, K. C. Shaver

Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km

Jan 1, 1998

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By F. A. Forward

"NINETEEN sixty-six is a year of unusual significance in our Institute and in our country. It marks two-thirds of a century of service by the Institute to the people of the mineral industry and two-thirds of the century that Sir Wilfred Laurier said ""belongs to Canada."" As we meet here today within the historic walls of Canada's oldest city, a city that looks back on three hundred and fifty years of progress, I am reminded that it is almost a third of a century ago -in April, 1934 -that here in Quebec I first attended an Annual General Meeting of the Institute. It occurred to me that it might be appropriate to examine briefly the change that the middle third of this century has brought in the affairs of the mineral industry and, with some trepidation, to consider the prospect for the third that lies ahead.Opinions differ as to the relative importance of factors that have been responsible for the expansion and growth of Canada in its first hundred years. Some will say that it has been due to the abundance and fertility of agricultural land, others to the early enterprise of the railroads, and financiers believe that the banking system has been a major factor; -the fisherman -the forester -the teacher -each has his own view. I suspect, however, that most of us here would subscribe to the thesis of T. A. Rickard -miner, author, imperialist -who wrote, a gene-ration ago, ""Trade follows the flag, but the flag follows the pick,"" and thus agree that the finest contribution to progress, to wealth, to extension of frontiers and to inter-national trade has been provided by the mineral industry."

Jan 1, 1966

By R. B. Anderson, N. J. Sherren

The mining equipment at the Scully Mine, Wabush, consists of approximately twenty-five large haulage units, eight large dozer-loader applications and seventy other related pieces of service and maintenance equipment. This equipment is operating in sub-Arctic conditions. This pa-per presents a description of the tire maintenance procedures in use here and discusses the tire troubles that are being encountered and the methods of dealing with them.

Jan 1, 1969

By J. K. Gowans

The Research and Design group of the Project Development Division (PDD) of Placer Dome Inc. includes metallurgical, electrical, civil and mechanical engineers. They provide metallurgical research and conceptual flowsheet development, feasibility concepts for the processing and ancillary facilities, and manage the detailed design of the facilities once approval has been given to a mining project. This paper describes how this group works, within the Project Development Division, to help develop feasibility studies with the Evaluations Group, manage detailed design, and provide support for the Construction Group. The paper briefly reviews the history and growth of the group and describes how it is evolving. The role of outside engineering firms and how they are incorporated into the division’s objectives are also discussed. The paper highlights the differences between Placer Dome’s Project Development Division and other mining groups, and why this approach fits the way Placer Dome does business.

Jan 1, 1998

By S. Shairp

At the Hudbay zinc pressure leach plant, filtration and washing of the second stage leach slurry takes place on a vacuum belt filter prior to disposal to tailings. Due to periods of poor filterability, laboratory studies were undertaken to investigate the effect of temperature of the filter feed slurry, and to compare filterability to the resulting cake particle size distribution.

Jan 1, 2014

By A. B. Rossetti

"THE MISSION TO Offshore Scotland was in my opinion a very worthwhile venture, as it indicated the scope of the offshore oil and gas business and how we might exploit it to the fullest here in Nova Scotia - if our offshore fields eventually become producing fields. The writer was able to attend a considerable number of lectures and as a result gained some valuable know-how on the engineering design, financing and operation of the North Sea oil industry. There are many new fields of technology that had to be developed to overcome the North Sea's hostile environment and a great deal of the same technology will have to be developed to win oil and gas from our continental shelf. The visit left me with several impressions, which in the main are:(1) The high order of investment required to develop offshore oil. The investment ranges from 10 to 20 times that required for a similar output on land. Each barrel of oil costs on the average of about $2,- 500 per barrel per day.(2) Because of the high investments required, before the first oil is produced the field must be brought into production at the earliest possible date and initial lead time from decision to production is less than four years. In the British Petroleum field, working at a depth of 450 feet will require an investment of $900,000,000 to develop a production of 400,000 bbl per day. (3) The size and complexity of equipment required is beyond anything ever imagined. Problems which must be overcome are such factors as water depth, wind velocities, wave height, wave period, long periods of darkness, low temperatures, distance from land, and fog."

Jan 1, 1973

By F. Chiesa

The permanent mould process, which is a favoured process for producing premium quality aluminium casting, is rarely used to produce magnesium alloy parts. This may be attributed different factors such as: the reservation with which the automotive industry considers using magnesium in structural castings; also the relative hot shortness of most magnesium alloys when compared to aluminium A356/357 is another factor. A third reason stems from the fact that the "heat content" of magnesium is much less than that of aluminium, resulting in the difficulty, for a relatively slow process such as permanent mould (versus pressure die casting), to reach a mould dynamic equilibrium temperature sufficiently high to avoid premature freezing and misruns. The present work will address this problem by carrying out controlled cycling of a laboratory mould, poured with aluminium and magnesium alloys. The influence of insulation of the mould and artificial electric heating on the run-in mould temperature will be determined experimentally. A thermal model will be sought for these thermal devices that will allow to predict the thermal behaviour of moulds of different geometry before a single casting is poured. The model will be tested on an industrial casting in a workshop environment.

Jan 1, 2006

By A. C. Stevenson

"The most common theory is that, since thyristors, diodes, and insulated gate bipolar transistors (IGBTs) are “solid state” they will live forever. This is not so. They have wear-out mechanisms (e.g. insulation) and other mechanical parts such as motor bearings. These wear-out phenomena can be easily calculated. In this paper we will look at some of the failures and the failure rate of thyristors in power converters to see what affects them and to see what improvements can be made. If converter failures do occur, some simple forensic engineering steps will show if this is the root cause of the problem.IntroductionLook at the general failure rate curve for thyristors, diodes, gate turn off devices (GTOs) and IGBTs shown in Figure 1. We see that there is an initial high failure rate due to manufacturing defects, application problems, and drive start-up stresses that lasts for a few weeks. This is followed by a long period of (hopefully) several years with a relatively low but very slowly rising failure rate. At the end of this period, the devices start to wear out and the failure rate suddenly starts to increase rapidly over a few months. This signals the end of life for the devices in the system. We will start by looking at this end of life area."

Jan 1, 2000

By A. W. Jolliffe

DESPITE the widespread occurrence of scheelite in Canada, domestic production of this strategic mineral is still quite insufficient to meet wartime needs. Two difficulties have invariably arisen in prospecting for or developing scheelite deposits: scheelite is a difficult mineral to identify, and secondly, its distribution is commonly so erratic that the value of a deposit cannot be determined without arduous and expensive methods of sampling and wet assay. Scheelite's property of fluorescing under certain ultra-violet lamps overcomes the first difficulty and is the basis for a quantitative method developed to overcome the second. It is found that, by use of an ultra-violet lamp, the value of many scheelite deposits may be accurately and speedily determined. The method requires neither elaborate apparatus nor exceptional skill on the part of the operator, and is most applicable to those deposits where the bulk of the scheelite occurs in fairly pure aggregates that are at least one-tenth of an inch across. It has been used in grading some two hundred scheelite-bearing veins in the Yellow-knife-Beaulieu region, Northwest Territories, and various occurrences in the Porcupine district, Ontario. The method requires the measurement of the total area of scheelite exposed in any reasonably large measured cross-section of a deposit. From the areal percent of scheelite so obtained, the tungstic oxide (WO,) content of that part of the deposit may be calculated by means of equations of simple derivation.

Jan 1, 1942

By Elizabeth Edwards, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg, Kurtis Judd

Mineralogical characterization of the tailings showed the deportment of Ni to be similar in the Vale and Glencore tailings, with 60% of the total Ni locked in pyrrhotite, and the balance 40% associated with pentlandite. The overall Ni dissolution was correlated with the individual dissolution extents of pyrrhotite and pentlandite as functions of four leaching regimes: ‘anoxic acid’ (with and without pH control), ‘oxic acid’ (oxygen sparging), ‘oxic acid’ (air sparging), and ‘oxic ferric’ (air sparging). The results showed that the maximum Ni dissolution was obtained during the pH controlled oxic acid leach with oxygen sparging at pH 1.5, while the anoxic acid leach at pH 1.5 resulted in minimum Ni dissolution (10–15%) from pyrrhotite. An overall Ni mass balance showed that pyrrhotite and pentlandite dissolve simultaneously in the presence of Fe(III) and oxygen, in contrast to the preferential dissolution of pyrrhotite in the absence of Fe(III). Sulphur mass balances revealed that the yield of elemental sulphur is maximized (65%) during the oxic Fe(III) leach at pH 0.6. Furthermore, the kinetics of Ni leaching and elemental sulphur formation from pyrrhotite tailings leached with ferric sulphate between 55–80°C was investigated at constant oxidation-reduction potential. Elemental sulphur yield increased with increasing temperature, but no observable trend could be linked to ferric or ferrous ion concentration.

Jan 1, 2017

By J. H. Sokolowski, R. I. MacKay

The level of Si and Cu in the 3xx series of alloys affects the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase. The volume fraction of these phases in turn affects the feeding conditions during solidification and ultimately the Area Fraction Porosity and Mean Pore Diameter measured in the as-cast structure. This work sets out to establish the relationship between the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase and the resulting porosity that forms on the Monotonic and High Cycle Fatigue properties. The alloys in question are the Al-9%Si-l %Cu and a Al-7%Si-4%Cu alloys which were cast into V8 performance engine block castings and then heat treated to achieve desired mechanical properties. The engine block castings provided the mechanical and metallographic test samples analyzed for this work.

Jan 1, 2006

By Bahaa Hussein

Considerable number of methods and procedures has been introduced for trending and progress reporting of engineering, procurement and construction projects. This paper introduces a novel method, designed to augment the set of indices for measuring schedule performance. The concept behind the developed method is to provide early warning by dynamically evaluating the schedule cumulative impact of construction projects. The proposed method is designed to highlight the gradual deterioration in schedule status resulting in a cumulative impact due to the aggregation of small delays encountered during the execution of non-critical activities, and can be used as an add-on utility to existing software systems that perform CPM scheduling. The proposed method is based on a developed formulation for quantification of the Schedule Compression Index, which takes into consideration the remaining project activities durations. The index is developed based on periodic comparisons of ?Current Schedules? and the project ?Baseline Schedule? using the summation of the remaining activities durations. A numerical example is presented to demonstrate the application and capabilities of the developed method. It is expected that the developed index together with other schedule performance indices would be of value to decision makers and members of project teams.

Aug 1, 2013

By J. B. Kwon

For improvement in the productivity of tall building projects, table formwork is one of the main methods that have been adopted for slab formwork. Because the table formwork method is an equipment-oriented construction method, the type of lifting equipment and method of operation considerably affects the productivity and cost of the table formwork. It is also important to make an equipment input plan for completing the table formwork within the time given, according to the structural construction cycle. For performing the table formwork, a tower crane or an independent lifting system, and shifting trolleys, are required. However, if an inefficient equipment input plan is made, exorbitant cost may be incurred. Therefore, the purpose of this study is to analyze the productivity of a table formwork, considering the type and number of lifting equipment and the number of trolleys inputted, and to suggest quantitative data for making a cost-efficient equipment input plan within the construction duration given. It is expected that the results of this research will be utilized as a basis for cost-efficient equipment input planning.

Aug 1, 2013

By W. Hardtke, B. Perry

Model reconciliation problems at the low-grade, high-nugget Phoenix gold-copper deposit led to an examination of the influence of production decisions on ore-waste classification. A conditional simulation study of the deposit was used as the basis for: 1) quantification of dilution at different bench heights, 2) quantification of ore-waste misclassification relative to bench heights and cut-off wades, and 3) determination of an appropriate number of samples to optimize ore-control polygon definition. Actual reconciliation data were empirically used to support conclusions. Simulations of both gold and copper were combined through net revenue modelling. These simulations increased understanding of the nature of the deposit and provided insight for resource modeling and mine planning.

Jan 1, 2011

By Jun Dai

Based upon research findings from several countries, the combination of microwave and mechanical means to break hard rock holds promise for the future. To achieve this goal, it is essential to understand the laws governing strength reduction of hard rock, such as granite, induced by microwave irradiation. Two aspects to consider are: 1) laws associated with the tensile strength of hard rock after microwave irradiation and 2) the sensitivity of different types of rock strengths to microwave energy. In this study, granite with a range of tensile strengths was exposed to microwaves for various time periods to compare the response of rocks with different strength values exposed to the same microwave irradiation. In addition, a method based on hotspots is presented to explain the mechanism by which granite strength is reduced by microwave irradiation. Granite extracted from Qinling Mountain in Shaanxi Province, China is used in the research. ?50 × 50 mm cylindrical granite specimens were exposed to microwaves at a specific power level. The strength values of the heated granite specimens were compared with those of unheated specimens. Through the comparison and analyses, relationships were determined between 1) reduction in granite strength and microwave irradiation time period, and 2) granite strength and sensitivity to a given energy of microwave irradiation. Finally, a mechanism to explain the experimental results is proposed. Research findings will aid in the design of a microwave + machine rock-breaking system for use in rock breakage in underground mines at depth and for future mine applications on earth and other planets. In addition, the experimental approach could be used to test other rock types to further our understanding of rock damage induced by microwave irradiation.

Aug 1, 2013

By P. C. Parsons, G. C. Milligan

"IN FIELD WORK in the Cape Breton Highlands, which are heavily covered with vegetation, it is necessary to run traverses along the valleys of small brooks. We encountered difficulty in closing such traverses, and the following technique was developed to solve this problem. It has been tested in the field for four seasons by several people, and found to be simple, efficient and more accurate than any other compass-and-pace system of which we are aware. So far as we can find, the technique has not been described previously. It may be of use to others.The Cape Breton Highlands of Nova Scotia consist of hills of old intrusive and metamorphosed sedimentary rocks protruding up to 1,000 feet above the general level of the younger sediments which underlie the valleys. The flat hill-tops are the remnants of a plateau; drainage off the edge of this plateau has produced many small steep brooks. They occupy valleys which are up to 800 feet deep, and V-shaped in cross section, with steep sides covered by mixed conifers and hardwoods. The stream at the bottom is rarely more than a few feet wide, with a negligible meander belt, but with many bends, rapids and falls. Visibility along the stream, in consequence, is rarely more than a few hundred feet, and in many places much less.It was found impractical to map the streams by the method of meander lines, as described in many standard surveying texts and hand-books. The limited visibility, and the numerous bends of the brooks, necessitated many corners. Every corner introduces errors. To 'close' a survey with 40 or 50 such corners proved either very time-consuming or impossible. In most cases, however, the general direction of a valley may be obtained from an aerial photograph, or by direct observation, and this became the basis of the method adopted."

Jan 1, 1971

By M. Kowalczyk

The successful application of color sorting machines has established sensor-based sorting in the mineral industry in recent years and is considered today as a significant innovation in processing technology. However, we are only at the beginning of the (market) introduction. New sensor systems have been developed, which exploit material properties such as electrical conductivity, magnetization, molecular structure, thermal conductivity etc. This opens up new exciting pre-concentration and upgrading possibilities for many applications such as nickel, gold, copper and other ores as well as for industrial minerals, diamonds and other gemstones.

Jan 1, 2009

By Yin Wang, Lin Li, Zhongwei Bi, Like Wei, Wen Li, Shaogang Li, Bin Zhang, Hongjie Li

Presently,Many long-wall fully-mechanized faces in shallow depth coal seams are below room and pillar goaf in Shendong mining area. When the working face is advanced out of concentrated coal pillar in upper room and pillar goaf, strong strata behaviors often cause support crushing accident. Aiming at a support crushing accident which happened in Shigetai coal mine of Shenhua group in Shendong mining area, this paper analyses the stress transfer process while mining out of concentrated coal pillar by numerical simulation software FLAC3D. According to the feature, simplifying the roof of upper room and pillar goaf as supporting-beam structure explains mechanism of large area collapse in room and pillar goaf roof. Based on the feature of supporting-beam structure, deep-hole blasting concentrated coal pillar technology is proposed to control the strong strata behaviors in Shigetai coal mine. The blasting control effect is confirmed through characteristics of strata behaviors, growth circumstance of ground crack and multi-point extensometer monitoring results. By using control technology, Shigetai coal mine has been successfully avoided support crushing accident.

Jan 1, 2015