Search Documents

By Kati Tschöpe

Cathode wear has become an increasing challenge in the aluminum industry due to the use of more graphitized materials. Today, there exist no standard laboratory methods for measuring cathode wear where different commercial materials can be ranked. The typical average wear rate in an electrolysis cell is quite small. The aim of this work was to design a test method where the wear could be accelerated compared to industrial cells. It was focused on polarized tests where the cathode is exposed to electrolyte, which gives higher aluminium carbide solubility. The cathode materials were characterized by microscopy and image analysis.

Jan 1, 2011

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

By N. Manopulo, J. Maier, L. Tong, C. Becker, P. Hora

The contribution presents a new finite element approach in which the common updated Lagrangian formulation is replaced by a spatial flow formulation applying a special arbitrary Lagrangian-Eulerian for-mulation (ALE). The description separates spatially the process in a die inside zone and in a profile zone. For the description of the inside zone, where the filling process occurs, a special Euler time independent mesh is applied. By this formulation the mesh has to be generated only once, which simplifies the generation of spatially optimized meshes. For mapping of the material flow during the filling process the method uses a flow surface traction method as applied in casting simulations. A further strength of the new method is the computational efficiency which allows the modelling of extrusion process with the highest complexity with a response time of 12 hours, which is important for the industrial optimization process.

Jan 1, 2015

By Gaston Gingras

"IntroductionL'entretien de l'equipement minier dans les mines à ciel ouvert est une activité qui est aussi vieille que I'existence des mines et qui a progressé au cours des années pour suivre l'évolution des techniques d'exploitation. Lors de la mise en usage de s premières pelles à la va peur, celles-ci étaient généralement entretenues par I ‘équipe de quatre hommes qui était responsable de son opération. Pour les travaux plus compliqués ils utilisaient les services de machinistes qui eux savaient comment réparer Ie moteur à vapeur et couler des coussinets de ""babbit"". Les premières pelles diesel étaient entretenues de la même façon mais pour les réparations au moteur, on devait recourir au représentant du manufacturier qui était Ie seul à avoir les compétences nécessaires.Ce n'est vraiment qu ‘après la deuxième guerre mondiale que I ‘usage de l'équipement mobile s'est répandu dans les mines à ciel ouvert pour débuter les extractions selon les méthodes que I'on connaît aujourd'hui.L'entretien de l'équipement minier de façon organisée à débute avec I ‘usage de ces machines dans nos mines. Ces machines étaient un peu primitives, petites et pas très dispendieuses a I'achat. Même si la disponibilité était basse, elles fournissaient quand même un rendement qui en ces temps était acceptable. L’organisation de I ‘entretien de cet équipèrent était assez primitif et n'occupait qu'une place secondaire aux yeux de la direction de la mine."

Jan 1, 1988

By H. Saeedi Ali, A. J. Monhemius

"Anglo Asian Mining’s Gedabek mine is situated in the Lesser Caucasus mountains in Western Azerbaijan. The ore body is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold and copper-bearing ores. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions. Ore processing at Gedabek is by agitation leaching for high grade ore (>1g Au/t) and heap leaching for lower grade ore. In order to cope with the high copper concentrations in the cyanide leach liquors, a unique combination of resin-in-pulp for selective gold extraction and SART processing for copper removal and cyanide recovery is used. In 2015, a flotation plant was added to treat the tailings from the agitation leach plant before the tails are sent to the tailings dam. This plant produces a copper sulphide flotation concentrate and also recovers some of the residual gold and silver in the tailings. Since February 2017, due to lower grades of gold and higher copper in the feed ore, the decision was taken to alter the flow sheet and to carry out flotation ahead of agitation leaching, to reduce the cyanide consumption during leaching by removing soluble copper minerals. The paper compares and contrasts the performance of the plant in the two configurations, namely, (i) leaching followed by flotation and (ii) flotation followed by leaching.INTRODUCTION In May 2009, Anglo Asian Mining started open pit mining for gold on its Gedabek property in the Lesser Caucasus Mountains in western Azerbaijan. Gedabek is situated on the highly mineralized Tethyan Belt that runs from the Himalayas to the Balkans. The ore body at Gedabek is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold-bearing ores. The sulphidic ores contain mainly pyrite and chalcopyrite, with some secondary copper sulphide minerals, such as bornite and chalcocite, and minor amounts of sphalerite, galena and tetrahedrite. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions and passivation of free gold."

Jan 1, 2017

By Liang Zhen, Jian-Tang Jiang, Guo-Ai Li, Xiao-Ya Wang

"Deformation behavior of 2A97 aluminum alloy containing coarse secondary phases was studied using uniaxial hot compression (HC, 340–490°C, 0.4001–1 s-1). The flow stress could be described by a Zener-Hollomon parameter in hyperbolic sine function with the hot deformation activation energy of 237 kJ/mol. Based on the experimental data and dynamic materials model, processing maps were generated to demonstrate the hot workability of the alloy. The coarse secondary phases experienced dissolution by varying degree under different deformation temperature, which producing different effects on the microstructure evolution. When deformed at relatively low temperatures, a mass of fine grains shaped up in the original grains and grain boundaries, and the dominating deformation mechanism was believed to be dynamic recrystallization. As the deformation temperature rising to 490°C, most secondary phases disappeared and few recrystallized grains were observed, indicating that the secondary phases dissolved sufficiently along with dynamic recovery occurred during the hot deformation. Particle stimulated nucleation related to the coarse secondary phases was believed to promote the recrystallization and the recrystallization behavior was sensitive to deformation temperature.INTRODUCTION Al-Li alloys has received much attention as new promising structural materials in the aircraft and aerospace industries, due to their lower density, higher elastic modulus and improved fatigue crack growth resistance in comparison with the conventional commercial aluminum alloys (Ou Ling, 2015). 2A97 alloy is one of the 3rd generation Al-Li alloys targeting at comprehensive improvement of aviation aluminum alloy and applications for wing spars and ribs to other internal structures for transport aircraft. Al-Li alloys are usually formed by hot deformation, either by rolling or extruding. The deformation behavior and resulted microstructure evolution during the forming process mainly dominates the formability of the alloy and the serving performances as well. Therefore, the deformation behavior and microstructure evolution at elevated temperature need be made clear for optimizing the hot processing parameters and controlling microstructure evolution."

Jan 1, 2018

By Alexander Smith

"The three principal known mineral deposits of the Taku River area lie in the Tulsequah synclinorium. The axis of this north-south trending structure is along Tulsequah River valley; about 6 miles east of the eastern contact of the Coast Range batholith.The one proven mine of the area, the Polaris-Taku, is on the west side of the valley. It is a gold property, the gold occurring in fine needles of arsenopyrite disseminated in carbonatized volcanics. The mine was originally called the Whitewater, and the adjacent area the Whitewater gold belt. During the years 1937 to 1942 gold having a value of $3,284,000 was produced from 313,500 tons of ore milled."

Jan 1, 1954

By S. Beskri, N. Geoffroy

When metallurgical plants are designed, a lot of consideration is almost always given to material selection and possible damage mechanisms. Materials engineers are generally involved and will strive to select optimal alloys or refractories for the design conditions. Once in operation however, things often change. Equipment is overstressed to increase production, corrosive leaks are not always promptly addressed, proper welding procedures are disregarded, etc. This paper describes various cases from the mining and metals industry where serious mishaps, associated consequences, and costs could have been avoided if simple and proactive steps had been taken. It also presents a strategy, based on safety reviews, to help predict and prevent damage to critical pieces of equipment.

Jan 1, 2015

By G. Granata, C. Tokoro, M. Matsuoka, K. Horiuchi

"Given the high demand of copper and the lack of new high-grade deposits, low grade copper ores containing copper oxides and refractory sulfides need to be processed as well. However, in order to recover copper from refractory copper ores, the leaching performances should be improved. In this study, we investigated the effect of the mechanical activation in the leaching of copper from covellite. The influence of a mechanical treatment by planetary ball milling on leaching rate in sulfuric leaching media was evaluated by using X-ray diffraction (XRD), mineral liberation analysis (MLA) and X-ray absorption fine structure (XAFS). Results showed a significant increase in copper leaching from around 50%up to 100% along with an improvement of the leaching kinetics when using planetary ball milling. XRD spectra showed the disappearance of the covellite peak from (101) face, thus suggesting the amorphization of covellite associated with the use of planetary ball milling. XAFS results showed that the coordination number of Cu changed from 6 to 3, thereby confirming the effectiveness of the mechanochemical effect.INTRODUCTIONDuring the last decades, while the copper grade in copper ores has been decreasing, the concentration of impurities such as arsenic tends to increase, thus requiring for the processing of low grade copper ores. For a suitable processing of copper minerals, hydrometallurgical processes are preferable due to the lower costs, the lower environmental impact and the easier implementation (Watling, 2006). However, for an economical recovery of copper, the leaching performances must be improved.Among the recent advancements in leaching technologies, the mechanochemical activation allows for an improvement of the leaching performances by means of high-intensity grinding(Mohammadabad et al., 2016). In the first place, the improvement is the result of the dramatic decrease of particle size, which results in an increase of the mineral surface area and the consequent enhancement of leaching kinetics. Furthermore, the intense mechanical stress due to the high-intensity grinding could induce the rupture of the crystal structure producing a decrease of crystallinity. Such changes of the mineralogical structure, also known as mechanochemical effect, can lead to more leachable mineral, thereby resulting in a greater dissolution of copper. Last but not least, whereas the mineral surface might undergo passivation during leaching, the high-intensity grinding can continuously refresh the surface of the mineral, thus exposing portions of unleached bulk mineral."

Jan 1, 2017

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemicals are added to flotation circuits directly and indirectly to control issues such as scaling and dust in other areas of the operations. Since dosage levels are generally not high, a standard laboratory float test may not be able to determine the effect of a specific chemical on the productivity of the flotation circuit. This paper presents a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5–100 g/t). Results indicate that this protocol helps to predict potential interference by a particular chemistry on the flotation circuit.RÉSUMÉ Certains produits chimiques ne servant pas à la flottation sont ajoutés directement et indirectement aux circuits de flottation afin de contrôler des problèmes tels que l’entartage et la poussière dans d’autres secteurs des opérations. Étant donné que les niveaux de dosage sont généralement faibles, un essai standard de flottation en laboratoire pourrait ne pas être en mesure de déterminer l’effet d’un produit chimique spécifique sur la productivité du circuit de flottation. Le présent article définit une procédure d’essai en laboratoire qui utilise des études cinétiques de flottation pour vérifier l’effet de doses normales à extrêmes de produits chimiques antitartre et anti-poussière (5 à 100 g/t). Les résultats indiquent que ce protocole aide à prédire l’interférence potentielle d’un produit chimique particulier sur le circuit de flottation."

Jan 1, 2016

By D. R. BUDINSKI

Clinton Creek Mine in west-central Yukon produced 0.94 million tonnes of fibre from 15 million tonnes of asbestos ore between 1968 and 1978. The mine closed in 1978. The deposit lies along the margin of a medium sized ultramafic pluton that intrudes schistose and gneissic rocks of the Yukon Metamorphic Complex. Country rocks are metamorphic equivalents of a mixed sedimentary and volcanic assemblage deposited during Precambrian or early Paleozaic time. Movement along the north west-trending Tintina Fault System probably caused the fairly high meromorphic grade that altered the original rocks to schists and gneisses. The ultramafic pluton hosting Clinton Creek Mine is one of several bodies that were emplaced along a deep seated imbricate fault system parallel to the Tintina Trench. Most of rhe intrusions were hydrothermally altered to serpentinite, bur apparently only the one at Clinton Creek contains commercial quantities of asbestos. The Clinton Creek pluton was probably injecred slowly at relatively low temperatures into the crustal rocks as a "mush" that cooled gradually, allowing sufficient time for serpentinization and chrysotile fibre crystallizarion.

Jan 1, 1984

By M. M. C Jiménez, J. A. S Ténorio

For the recovery of valuable materials and for the protection of environment, recycling process of printed circuit board is an important subject of study. Moreover, the popularization of the computers and its technological evolution has generated a large number of waste electrical and electronic equipment. This paper presents a study of synergistic solvent extraction of copper, nickel and zinc from a sulfuric leaching liquor of printed circuit boards (PCB’s). The percent extraction of copper, nickel and zinc from dilute aqueous sulfate media besides synergistic effect of mixture of the .extractants Cyanex 272 and D2EHPA have been studied. Furthermore, different conditions such as temperature, pH of the feed solution have been examined. The results suggest that the synergistic effect of the .extractants mixture enhance the extraction efficiency of nickel.

Jan 1, 2014

By Lauri Pesonen

"Although electrical energy use at copper smelters is typically about 15-20% of operational costs, it is something which is not very often analyzed and discussed at a detail level in technical papers and presentations. This paper aims to list different equipment configurations per smelter area and estimate their electrical energy consumptions versus unit of material processed. In addition chosen smelting technology and oxygen enrichment rates affect the overall electricity consumption and therefore some overall guidance is provided for efficiency gains.INTRODUCTION In principle, processing plants, such as copper smelters, require electrical and chemical energy together with some degree of human input to process input materials into desirable output form like metallic copper. From the standpoint of metallurgical plant designers, the thermodynamics of smelting, when it comes to releasing and conserving thermal energy, is sufficiently understood and frequently discussed in the literature in detail, but judging from the quantity of publications, the way how we exactly utilize electrical energy is not. This article is meant to illustrate how electrical energy consumption is distributed among different process units and equipment types at copper smelters using various smelting technologies. In general, typically about 15-20% of operational costs are related to electricity and at locations with high electricity prices the potential savings can be quite significant for the overall profitability of the plant operations. In today’s tight profit margin environment any potential savings are more than welcome. The purpose here is not to promote any certain copper smelting technology, but to open a discussion on how and where we use electrical energy, and how the overall energy use could be lowered with the implementation of newest electric power saving designs and solutions. Using the principles outlined in this article, it should be fairly easy and straightforward to replicate the calculations and even improve them wherever it is seen necessary for the greater benefit for us all in this industry"

Jan 1, 2017

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

By H. Ishimoto

It always has been a serious issue to improve safety in mine sites, demolition work sites, and civil engineering work sites. Especially, collision accidents caused by construction equipment damage not only the productivity of operations but also the health and life of workers in those work sites. To solve this problem, a variety of worker auto-detection means are developed so far, but they have not still become widely used in actual worksites. There have been two controversial points in the prior methods. One is that they were not enough in respect of the detection accuracy and certainty, and the other one is that the information of the detection results was not comprehensible to the operator of equipment. In this paper, the functional requirements of the obstacle detection system in earth moving work site is redefined at first, and then, it is proposed to apply a stereo vision to the obstacle detection system for an excavator. The system consists of horizontally arrayed two digital cameras with low distortion lens, an image processing controller, and a monitor for an operator in the cab. Stereo vision calculates the depth image from images of two cameras and detects the presence of obstacles, its distance, direction, and dimensions. Sensed obstacles are informed to the operator in the monitor image. Preliminary experiments are conducted with a stereo vision system mounted on a real equipment in a demonstration site. The result shows that two controversial points of the conventional technologies are improved, and that the applicability of this system is validated.

Aug 1, 2013

By R. Walker

This paper deals with the selection and design of a belt conveyor handling steam coal between a mine and a barge loading terminal, and extending for some 5 ¼ miles over some of the most rugged terrain in the state of West Virginia, U.S.A. After a thorough analysis by consulting engineers and the owner's engineers, a single-flight cablebelt conveyor was chosen as representing the alternative of greatest reliability and lowest over-all cost. The value analysis and design features of the system are covered in this paper along with an updated report on the performance of the system since its start-up in the spring of 1969.

Jan 1, 1971

By P. Wanjara, M. Xiao

During fusion welding of aluminium alloys, the avoidance of defects (such as porosity, oxides, hot cracking, undercutting) as well as the ability to optimize the microstructure-property characteristics in the assembly are critical for the stringent manufacturing specifications in the aerospace industry. In this work, aluminium alloy (AA) 2024 was electron beam welded autogenously as part of a study to determine the influence of parametric conditions on the characteristics of the heat affected and fusion zones to obtain optimal welding conditions. In particular the evolution in the weld geometry, microstructure and mechanical properties were examined as function of the processing conditions, including beam current, beam focus, beam oscillation, linear heat input and welding speed. For optimized parametric conditions, microstructural examination of the joints revealed narrow fusion and heat-affected zones comprising of dendritic structures without the occurrence of defects that enabled a maximized joint efficiency.

Jan 1, 2006

By S. Devereaux, P. Gover, S. Everett

Having real-time data of blast furnace burden profile with respect to burden height and temperature is critical to making informed decisions on blast furnace operation. Given the high temperature and gaseous environment within the blast furnace shaft, traditional instrumentation has been limited at providing the level of real-time feedback information needed to optimize blast furnace operations. Infrared thermal imagery technology provides non-contact temperature measurement across the entire burden profile, allowing for better understanding of the dynamic movement of the burden within the blast furnace shaft. This technology increases blast furnace performance by improving the decision-making process for hour by hour operations. This paper will discuss the development of incorporating infrared thermal imagery technology into the operating strategy of a lead blast furnace.

Jan 1, 2015

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013

By M. Leahy

"Very little is known about the large scale fluid dynamics and associated distribution of copper in an operating electrowinning cell, yet they will have a major influence on mass transfer and plating quality. The CFD model in this work is used to simulate an entire EW cell with 60 cathodes and 61 anodes, or 121 anode–cathode pairs, elucidating for the first time the three-dimensional (3D) flow and copper distribution in an industrial cell. Two methods for the distribution of electrolyte are modelled:1. Downcomer method: electrolyte is fed by a downcomer at one end of the cell, overflowing at the opposite end.2. Manifold method: a horizontal manifold pipe runs the whole length of the cell and feeds electrolyte via small holes in the top of the manifold pipe.The recirculation that develops within each anode-cathode pair, driven by oxygen bubble generation on the anode, is similar to that seen previously in two-dimensional models of single anode–cathode gaps. However a more complex 3D flow recirculation is established, which involves flow of electrolyte down the side gaps (being a path of low resistance for return flow) as well as the usual return flow down the cathode side of each pair gap. The bubble-driven flow is not influenced by the mode of electrolyte distribution.The electrolyte flow due to the manifold and downcomer is somewhat secondary to the bubble driven flow. In the case of the downcomer distribution mode, the high injection velocity causes a very turbulent flow in the first 1–2 m down the cell from the downcomer, with several large vortices developing. This may lead to some sludge particles being entrained into the bulk of the cell.In the manifold pipe case, the jet from each hole is dissipated very quickly, within the first 10–20 cm. The jets are directed into the downward flowing zone of the bubble-driven recirculation, which leads to unstable and periodic behaviour on a large spatial scale.In both the manifold and downcomer cases, there is a marked two-zone vertical stratification in copper concentration."

Jan 1, 2016