Search Documents

By Thomas C. Poulter

Abstract The Poulter seismic method of geophysical exploration is an attempt to obtain an increased efficiency in the conversion of the energy of an m~pl06ion into useful energy which has directive properties and which contains a minimum of random frequency and random phase relations. Very little effort has been made in the past to simplify OT even control the uniformity of the seismic energy being introduced into the ground. The Poulter seismic method is also an attempt to improve the signal-to-noise ratio not merely by trying to complete the impartial filtering done by the earth on ,the continuous spectrum of primarily high-frequency energy radiated from a shot point but by applying a frequency control at the point of origin of the seismic wave. The energy from a shot-hole charge is peaked in a frequency which is much higher than will be transmitted through the ground, and its absorption introduces background interference. Only 10 to 20 per cent of the seismic energy of a shot-hole charge .is directed downward in a 90-degree vertical cone, whereas, from a pattern of charges detonated above the surface of the ground, 85 per cent of the seismic energy is included in a 90-degree cone and in some cases it is even confined to as small as a 30-degree cone. This greatly reduces the horizontally distributed energy, thereby producing a marked improvement in the signal-to-noise ratio. The frequency of the signal energy may be peaked in a rather narrow range by the proper application of two or more impulses upon the surface of the ground controlled as to direction, magnitude, and timing. These impulses may be controlled by the reflection shock wave technique, the pressure pulse technique, and the sequence firing technique, using the primary controls as outlined. The information obtained from the study of directivity of seismic energy in a high velocity, uniform material such as the ice on Taku glacier, in the Juneau ice field in Alaska, has been of great assistance in the application of the method to oilfield and mining problems.

Jan 1, 1950

By S. G. Luckey, N. R. Harrison, F. Nadeau, U. Brüx

"The adoption of tailored-rolled or tailor-welded blanks (i.e. TRB/TWB) in the automotive industry has been known to offer great potential for the optimization of weight, function, cost and complexity. Vehicle light weighting can further be achieved by using high strength aluminum alloys like the 7xxx-series. 7xxx-series alloys are capable of delivering specific strengths equal to or greater than high strength steels. However, room temperature formability of this aluminum class is limited, so one approach to forming 7xxx-series alloys is by hot stamping. Hot stamping utilizes an elevated temperature blank and the high pressure stamping contact of the forming die to simultaneously quench and form the sheet. This paper explores the initial feasibility of tailored thickness material for body-in-white applications when processed under hot stamping conditions.INTRODUCTION Steel tailor-rolled blanks (TRB) or tailor-welded blanks (TWB) have been used within the automotive industry as a method of reducing weight, expanding material utilization, and decreasing overall part/assembly cost (Ganeasan et al., 2015; Merklein et al., 2014; Hirt et al., 2005; Kridli et al., 2000). The production of such tailored thickness materials has resulted in over $2.5 billion (2016) in combined industry sales (Mubea, 2018). As automakers begin to adopt the manufacturing practices traditionally reserved for steel such as tailor rolling/welding with greater enthusiasm for vehicle light weighting, there exist an opportunity to expand the material database to extend beyond the traditional aluminum alloys found in current production. High strength aluminum alloys, i.e. 7xxx-series, are ideal for structural automotive applications due to their high specific strength; however, they have limited room temperature formability. Hot stamping, another manufacturing practice used by the steel industry, can be used to form these high strength materials. The combination of tailoring the thickness of a sheet material and hot stamping provides an opportunity for significant weight saving within an existing manufacturing footprint. This paper explores the potential and challenges of this approach when applied to structural body-in-white components. The methods for tailor rolling, tailor welding and hot stamping are described and applied to the production of a 7075 aluminum alloy B-pillar. The results are discussed in terms of feasibility and weight savings."

Jan 1, 2018

By C. S. Chen, Y. J. Luo, M. W. Gao, B. Li, Z. F. Zhang

"To obtain large-sized billets with fine grains and homogeneous elements distribution, uniform direct chill (UDC) casting process, based on annular electromagnetic stirring coupling with intercooling, was employed to produce 7055 alloy billets with a size of F584 mm in this study. The results indicated that there were the coupled effects of annular electromagnetic stirring and intercooling on grain refinement and element homogenization, and also the billets produced by the UDC casting process showed excellent hot workability in comparison to the normal direct chill casting process.INTRODUCTION The high solute 7055 aluminium alloy has a wonderful combination of high specific strength and hardness, good resistance to stress corrosion cracking and high fracture toughness, which is very useful in aerospace application (Yan et al., 2013; Mondal & Mukhopadhyay, 2005). The production of large-sized 7055 alloy billets with high quality is the basic condition for the subsequent application of 7055 alloy to the aircraft. Inhomogeneous microstructures and performances of 7055 billets result from the high alloying element content and the inhomogeneous cooling condition in different regions of billets during the conventional direct chill casting (Paramatmuni et al., 2004; Lalpoor et al., 2011), which will bring bad influence to processing property, functional performance and utilization rate of materials. To alleviate segregation and obtain fine and uniform grains, some effective treatment methods were proposed including electromagnetic stirring (EMS) (Vives, 1989), ultrasonic vibrating (Zhang et al., 2011) and melt conditioning (Fan et al., 2013), on the melt to obtain fine and uniform grains. However, these methods could not effectively decrease the large temperature difference between central and periphery parts of the billet, because the solidification mainly depends on outside cooling including mould cooling and water spraying cooling. To change the heat extraction pattern of the billet functioned solely from the outer surface, based on annular electromagnetic stirring (A-EMS) invented by Xu et al. (2010), Luo et al. (2017) proposed uniform direct chill (UDC) casting coupling A-EMS with intercooling in the direct chill (DC) casting process. An in-mold cooler was inserted to the melt sump, and thus the alloy melt temperature and concentration at solidification front become more uniform."

Jan 1, 2018

By T. W. Wlodek

"AbstractSatisfactory mine drilling operations depend on the good performance of the drilling machine, and of what may be called the drill set, i.e., the following four elements: bit, attachment, drill rod, and shank end. The field performances of these four elements in the drill set are analysed and their service lives are compared. The most .common causes of service failure are reviewed and possibilities of increasing service life are discussed.The laboratory methods now employed for the simulated service testing of tungsten carbide bits, conical push-on and threaded .types of attachments, drill rods, and shank ends are described, and some results are discussed. The objectives of the research programme now being carried out •on the above mentioned elements are outlined.A number of mines in British Columbia, northern Ontario, and northern Quebec have been visited, and, with the co-operation of the C.I.M. Branches in these areas, meetings with representatives of the mining and steel industries concerned have been held. In this paper, the mechanical-metallurgical problems most frequently encountered and discussed during these visits and meetings are described and .analysed.IntroductionSUCCESSFUL mine drill operations depend to a great extent on• the satisfactory field performance of the four elements which form the mining drill set, shown diagrammatically in Figure 1.These important elements are:1. -The bit, which may be one of the following types:(a) Detachable tungsten carbide bit( b) Inserted rod bit, so called chisel bit( c) Detachable steel bit( d) Solid rod bit"

Jan 1, 1952

By R. M. Berry

A brief outline of refining methods used to (1) upgrade yellowcake to nuclear purity and (2) convert the uranium to the chemical and physical forms required by the fuel fabricators is presented. The uranium hexafluoride (UF6) production facility now under construction at Eldorado, Port Hope, is discussed. Technological improvements in uranium refining are considered.

Jan 1, 1969

By M. Dadvand, G. Kipuros, A. Dadvand

"The ability to codeposit fillers within a nickel matrix has led to the production of a new generation of cermet coatings with properties useful for various applications. Hexagonal boron nitride (hBN) is a ceramic-type particulate matter with thermal conductivity, thermal stability, inertness, and lubricity properties that allow it to be codeposited. In this paper, a method was developed for modifying hBN surfaces to allow them to be uniformly dispersed in water-based solutions such as an electroless nickel plating bath. hBN surface modification improved wear performance of the electroless plated cermet due to enhanced interaction between the particulate and nickel matrix. RÉSUMÉ La capacité à effectuer un dépôt simultané de charges dans une matrice nickel a abouti à la production d’une nouvelle génération de revêtements cermet (une combinaison de céramique et de métal) dotés de propriétés très utiles pour diverses applications. Le nitrure de bore hexagonal (h-BN) est une matière particulaire de type céramique utilisée pour ses excellentes conductivité et stabilité thermiques, son inertie ainsi que son caractère lubrifiant, qui permettent son dépôt simultané. Cet article explore une méthode mise au point pour modifier les surfaces du h-BN de manière à ce qu’elles se répandent uniformément dans des solutions aqueuses telles qu’un bain de dépôt autocatalytique de nickel. La modification des surfaces du h-BN a amélioré la résistance à l’usure du placage autocatalytique du cermet en raison d’une interaction accrue entre la matière particulaire et la matrice nickel.INTRODUCTION Electroless nickel alloy coatings can be used for many applications; however, the need for improved tribological properties such as higher wear resistance and better lubricity has increased interest in incorporating particulates (fillers) into the nickel matrix by codepositing the particulates with nickel during the plating process. The selection of the particulate type depends on the desired properties (Sahoo & Das, 2011; Sudagar, Lian, & Sha, 2013). In terms of tribological applications, electroless nickel-based composites are categorized mainly into lubricating and wear-resistant composite coatings depending on the type of particles incorporated. The electroless nickel-phosphorus (Ni-P) composite coatings are composed of codeposited solid lubricants such as polytetrafluoroethylene (PTFE), graphite, WS2, MoS2, and hexagonal boron nitride (hBN) and, compared to nanocomposite electroless Ni-P coatings, they demonstrate a lower coefficient of friction. On the other hand, the nickel-phosphorus wear-resistant composite coatings are composed of hard particles such as silicon carbide (SiC), aluminum oxide (Al2O3), boron carbide (B4C), silicon nitride (Si3N4), diamond, tungsten carbide (WC), and zirconium oxide (ZrO2) and, compared to nanocomposite electroless Ni-P coatings, they have higher hardness and better wear resistance (Sahoo & Das, 2011; Sudagar et al., 2013; Parucker, Klein, Binder, Ristow, & Binder, 2014; Chakarova, Georgieva, Petrova, Dobreva, & Stoychev, 2016)."

Jan 1, 2018

By D. M. Ramsey

HIGH-INTENSITY magnetic separation as now practised in the commercial treatment of a large variety of industrial minerals is a com-paratively recent development, having had its practical beginning about ten years ago when it became necessary to devise more effective methods for the purification of the electric furnace abrasives and refractories-silicon carbide and fused aluminium oxide. The fundamentals of magnetic separation are, of course, very well under-stood; bur while very, very old in principle, the process has, in recent years, been developed to a point of far greater usefulness than heretofore. In fact, until the development of the high-intensity process,. magnetic separation was limited largely to the removal of tramp iron? with magnetic pulleys and the removal of the very highly magnetic portions of industrial minerals by means of horizontal conveyor-belt-type separators. All magnetic separation processes depend for their success on the fact that various materials are kinetically influenced to a greater or lesser degree by the force that we speak of as 'magnetism'. We have now come to regard 'magnetic separation' and 'high-intensity magnetic separation' as two different and distinct methods. However, both depend upon the reaction of a particle when placed in a magnetic field. The common types of magnetic separators quite generally operate on the principle that a magnetic particle can be lifted by a powerful magnetic force from a stream of material moving on a belt or other type of conveyor. The application of the force removing magnetic material by this scheme is directly opposed to the force of gravity and is, therefore, limited to sub-stances of a relatively high order of magnetic susceptibility, such as metallic iron and magnetite. Until a few years ago, one very important principle was almost entirely overlooked. Practically every substance is susceptible to some extent, at least, to magnetic attraction, and by the application of a magnetic force great enough, and properly applied, separations of materials heretofore considered 'non-magnetic' can be accomplished.

Jan 1, 1937

By L. T. Pasiechnyk

After a brief review of the various hydrocarbon storage methods currently being utilized and statistics on underground hydrocarbon storage, this paper will briefly describe the technology involved in solution mining salt to create caverns of engineered shape and size and briefly discuss the economical and environmental advantages of hydrocarbon storage in solution-mined salt caverns. Other possible uses of salt caverns will be mentioned.

Jan 1, 1978

By Jorgen Elbrond, Noel Billette

"La connaissance du niveau de variation de I' alimentation d' une usine minéralurgique est essentielle pour estimer le taux de récupération dans un concentrateur. De plus, il est important de connaître la période moyen ne de correlation afin d’améliorer la qualité des contrôles et de l' au tornatisation.Le modèle proposé permet de prédire ces paramètres à partir du minerai en place et des activités d'exploitation dans une opération à ciel ouvert. II est basé sur la combinaison des variogrammes directionnels dans diverses zones d'un gisement, ce qui permet de définir la correlation à la sortie de chaquc zone en fonction des decisions opérationnelles, puis sur une loi binômiale modifiée, afin de séparer minerai et stériles dans Ie but de décrire variance et corrélation dans Ie minerai même, Les statistiques classiques sont alors utilisées pour décrire la combinaison de plusieurs zones et obtenir la variance et la correlation au concentrateur.IntroductionUn concentrateur est habituellement rodé de facon à recevoir une alimentation à teneur fixe en métal ; Ie minerai qui s'y presente a, par contre, tendance à osciller auteur de cette valeur cible, tantôt plus riche , tantôt plus pauvre . Ces variations entraînent des pertes de deux types: tout d'abord, la teneur du concentré oscille de facon similaire à celle de l' alimentation , ce qui peut même impliquer des pénalties a I'usine de smeltage lorsqu'elle est trop riche ou trop pauvre; la récupération peut pour sa part être diminuée de plusieurs points par un engorgement du circuit lorsque la teneur est trop forte."

Jan 1, 1984

By Chris M. Healey

"Abstract - Perhaps the single most significant variable in the evaluation of a mining project is the reserve estimate. Many parameters are considered when estimating reserves, among them geology. This paper examines the link between the quality of a reserve estimate and a good understanding of the geological controls for the deposit. A clear understanding of the geometry is essential to the accurate definition of the shape and size of the deposit. This includes the definition of any structural controls as well as the proper interpretation of the stratigraphy. Further when the distribution of grades is erratic and there is consequently a high nugget effect, there are significant problems in estimating the true grade of the deposit.Two Saskatchewan examples are presented, one with good knowledge of the controls and therefore good estimates of reserves, and the other with a poor understanding of the geology and resultant problems in deriving good estimates. In both cases the reserve estimates at various stages in the project development are compared to actual results from underground work. The first example is the Star Lake Mine where just about all the estimates were within 10% of the actual on both tonnage and grade. The Laurel Lake deposit is discussed to show how problems in interpreting the geological data make reserve estimation very difficult. Laurel Lake has the additional problem of erratic grade distribution."

Jan 1, 1992

By G. Guiglionda, A. Deschamps, F. De Geuser, M. Langille, B. J. Diak

"Increased demand for light-weighting in passenger vehicles has created a need for strong, light, ductile materials to be used in body-in-white applications. The AA6xxx-series of aluminum alloys are suitable candidates meeting most requirements but can fall short of the formability demands of designers, necessitating an understanding of what controls the formability in this alloy series. This work examines the effect of copper alloying in AA6xxx on the pre-ageing and natural ageing responses of the microstructure and mechanical properties. The changes in microstructure observed by differential scanning calorimetry and hardness testing are related to the work-hardening and strain-rate sensitivity parameters for these alloys measured by tensile testing. An observed asymmetry in the measured strain-rate sensitivity associated with increasing versus decreasing strain rate changes suggests that a different mechanism operates for the two conditions. It is postulated how this asymmetry in strain-rate sensitivity will impact the necking and ductility behaviour of these alloys.INTRODUCTION The widespread use of AA6xxx series alloys in the form of sheets has provided the need for a more thorough understanding of the complex interactions between composition, processing, resulting microstructure and ultimately, the mechanical properties of the alloys. Conventional industrial practices involve the production of rolled AA6xxx sheet (typically 1 mm thick) to be used for body-in-white (BIW) applications for auto body panels (Hirsch, 2004, 2014). The final metallurgical step prior to the shipment of these panels to manufacturers involves a solution heat treatment (SHT) reverting the ageing products of the alloys into solid solution and the product is then shipped to the customer. During this shipping time and while sheets are waiting to be used, the natural ageing (NA) process occurs whereby the strength of the alloys increases resulting in reduced formability. This can result in a product that is unable to meet the formability demands of the automotive manufacturer. As a result, industry has moved towards performing pre-ageing (PA) treatments to prolong the “shelf-life” of the material prior to it having insufficient formability. Once formed into BIW panels, the parts are then painted and subsequently undergo the paint curing heat treatment which consists of a short period of time at medium temperature, typically 20 minutes at 170–190°C. This short artificial ageing (AA) treatment, known as the paint bake (PB), provides additional strength and improved dent resistance for the material, but reduced formability. The PB result is strongly dependent on the PA treatment performed prior to the forming operation. Furthermore, the addition of copper (Cu) to a base Al-Mg-Si composition is known to increase the alloy’s strength. The goal of this work is to study the effect of Cu on strength, strain hardening, and strain-rate sensitivity (SRS) of these alloys, to understand the strength-formability compromise, for two separate heat treatment schedules; one including and one excluding the PA treatment, both followed by NA."

Jan 1, 2018

By A. L. McAllister

"MASSIVE sulphide deposits are found in two areas of New Brunswick, the St. Stephen area and the Bathurst-Newcastle area. In both, the geology in the immediate vicinity of the sulphide bodies is largely inferred from drilling results as outcrop is not plentiful and is, in fact, almost lacking in most places. With few exceptions these deposits have not been explored by underground methods. Consequently much of the. detail on the geology will only become known over a period of years as economic conditions make mining feasible.Much of the information contained in this paper has been supplied directly by company geologists. As a result of the number of contributors, some confusion of nomenclature bas to be anticipated. Cross-sections and plans of the individual deposits are, in most cases, as supplied by the companies concerned. Most of the interpretations are the responsibility of the author."

Jan 1, 1960

By R. Heikkilä

In this paper the utilisation of building information models (BIM) and construction automation on building sites is discussed. A lot of research has been carried out to develop new applications for using BIM to assist construction site planning, different operations and logistics. The methods of production control and management on site utilize BIM together with machine control and navigation systems. In Finland machine control systems and the automation of construction equipment is widely used in infrastructure construction. Recently similar methods have been introduced also in building construction. This paper describes some latest Finnish examples where BIM-software is used for the planning, execution and control of building construction operations. University of Oulu has studied methods and technologies to capitalize BIM-models. The research has been mainly in infrastructure construction but the activities have recently been extended to building construction. In this paper a BIM-based tower crane operation and control system is discussed as a case study. The aim of this study was to highlight the potential areas were automation can increase the crane productivity and improve site operations and logistics. The construction site managers and tower crane operators interviewed in this study were experienced in using BIM-models on site.

Aug 1, 2013

By W. W. Cummings

Canada's only current tungsten producer started up in 1962 with a small open-pit mine on the Flat River , 180 air miles north of Watson Lake, Yukon Territory. The orebody was in a contact-metamorphic skarn zone and contained about 1.5 million tons of ore grading an estimated 2.47% W03 and 0.5% copper. Near the end of the open pit , a new zone was discovered on the lower limb of the same structure, and the decision to go underground was made in 1972. The new "E Zone" contains over 4 million tons of ore grading an estimated 1.6% W03 and 0.28% Cu , and has been supplying the concentrator at about 175,0 00 tons/ year since late 1974. A continuing program of change and up-grading is necessary in the conversion from a seasonal open-pit mine with limited life to an underground operation with twenty years of reserves. Changes are necessary in plant and services as well as the mine. Also, environmental protection requirements have changed from rudimentary to rigorous over the life of the operation. This paper sums up the changes in the operation since 1971 and outlines the changes yet to come.

Jan 1, 1977

By F. E. Patton

"IntroductionAT NORANDA, the strength of the ore and wall-rocks per-mitted mining in large open stopes. While some of the orebodies were small and could be mined out in one stope, in most cases their size was such that it was essential that ore pillars be left during the first stage of mining. In these cases, backfilling has been necessary for ground control and to facilitate the later recovery of the ore in these pillars.This paper discusses the development of the •backfill and •its use in pillar recovery.GeologyThe ore bodies at Noranda occur as replacement deposits in a block of rhyolite flows and breccias, bounded on the north by the Horne Creek fault and on the south by the Noranda Andesite fault. Mineralization consists of pyrite, pyrrhotite, magnetite, chalcopyrite, sphalerite, gold, and various tellurides.The main orebody is a massive sulphide deposit designated the 'H' orebody. It is elliptical in plan, measuring roughly 400 feet by 800 feet, and is divided into two zones -Upper H, extending from surface to the 1,500-foot level, and Lower H, from the 1 ,500-foot level to just below the 3,000-foot level.Mining MethodsOpen stope mining in both Upper H and Lower H zones has been fully described in previous publications (1). A brief review only of the mining methods will be given here."

Jan 1, 1952

By D. N. Thurston

Luscar Stereo commenced construction of the mine at Coal Valley, Alberta, in August, 1976. It is designed to produce approximately 2.5 million clean short tons of steam coal annually - 2.0 million tons per year being committed to Ontario Hydro and 0.5 million tons per year being committed to Neptune Terminals for sale on the export market. The project involves constructing a heavy-media coal preparation plant, erecting a 42-cubic-yard dragline, constructing a shop/office complex, and developing three surface mining zones and associated facilities. As there were no existing facilities in the Coal Valley area, it was necessary to establish access roads, an airstrip, temporary utilities, fuel supplies, a construction camp, rail upgrading and communication services.

Jan 1, 1978

By C. Moreland

Fluidized low-temperature carbonization of coal, a recent development, offers a possibility of reducing fuel costs of coal-burning electric ?generating plants. The Research Council of Alberta have built a pilot plant and are conducting a programme to -develop a carbomzation plant for Alberta sub-bituminous coals which will produce char suitable for use as a .boiler fuel, and tar of a potentially high value as a ?chemical raw material. The economies of the process as a whole, and the value of the tar, have yet to be assessed.

Jan 1, 1958

By E. C. Harder

BRITISH Guiana, Great Britain's only South American colony, may be reached by very comfortable steamers, both from North America and Europe. The trip from North American Atlantic ports requires about 12 to 14 days; that from Europe about 18 to 20 days. A number of steamship lines, including Canadian, American, and Dutch, have regular sailings between North America and British Guiana, with calls en route at various interesting ports in the West Indies and northern South America. Moreover, several lines, including British, German, and French, have steamships operating regularly between Europe and the West Indies. Indeed, so popular have the West Indian voyages become in recent years that, during the winter months, special cruises in considerable number are organized for many vessels that ply in the trans-Atlantic service in the summer. A trip to British Guiana, therefore, has become a delightful experience. After visits at the various attractive Leeward and Windward islands and Trinidad, the approach to the low, flat, British Guiana coast, with its muddy coastal waters extending for many miles offshore, is somewhat of a contrast. Arrival in Guiana waters is signalled by the appearance of the modern high-power Demerara Light, located "on a shoal about twelve miles from the mouth of Demerara river. From this point, if the tide is right, a pilot takes the steamer across the bar, eight to ten miles offshore, and into Georgetown harbour. At high tide, the water above the bar ranges from 15 to 18 feet in depth, depending on whether it is neap tide or spring tide; at low tide, the corresponding depths are 9 to 11 feet. As the bar is of soft mud, however, it is usually possible for vessels to pass over it with a draught of about two feet in excess of that indicated by the tide tables. Upon nearing the shore, one sees first the Georgetown wireless towers, then the light-house and the tall chimneys of sugar mills and of various factories in Georgetown, and finally the palms and other tropical trees and the houses of Georgetown itself along the sea shore and the east bank of Demerara river. Extensive wharves operated by various exporting and importing companies stretch along the river bank and activity prevails in Georgetown harbour. The principal exports are sugar, rice, gold, diamonds, bauxite, balata, lumber, fruit and other tropical products. The imports are food-stuffs, wearing apparel, and manufactured materials of many kinds.

Jan 1, 1936

By D. H. d Hamly

THE work of Brown and others at Pittsburgh (Brown, Baum, Yant, and Schrenk, 1938)(1) and the success of their light field microprojector (Figure 1), have shown that the microscopy of dust quantitation can be greatly improved. It has been shown that dark-field microprojection of dust spots on konimeter slides is possible (Pullen, 1940), and this paper is a discussion of the new microprojector and a new counting method which is made practical by this instrument. The microscope makes possible the ready determination of the dustiness of mine ventilation air. Reduction of the dust concentration from a dangerous to a safe level involves one or more of the following: reduction of dust production, filtration of the air stream, or dilution with non-dusty air. Each of these raises important engineering problems of time and costs, and trustworthy information on the state of dustiness of the air is required ?both before and after the employment of any method of reduction. Records of this information may be divided into two broad classes concerned with safety: (1) the level of dustiness, and (2) the quantity and kind of dust produced by a machine under a given set of conditions. Though the first requires only one determination for a given time and place, numerous routine records are required to show the continuous safety of the air in an actively producing mine. Though repeated samples are required, highly accurate counts are not needed to show safety or to indicate whether a substantial increase in the non-dusty ventilation air has produced a proportionate decrease in the dustiness of the mixed air. The Devers and Gathercole konimeters have proved satisfactory instruments for this purpose in Ontario.

Jan 1, 1942

By J. O. G. Sanderson

THE Brazeau river is a relatively short foothills stream in western Alberta and its drainage area is limited to approximately 2,400 square miles. It rises near the head of the North Saskatchewan river, about two-thirds of the way from Banff to Jasper, and is confluent with the North Saskatchewan at a point about 40 miles north of Rocky Mountain House. It is not the purpose of this paper to describe the geology of all of this area. Only the central portion, which lies east of the outer limestone ranges and takes in the outer folds of the foothills belt, will be dealt with. This area is shown on Figure 1. A small portion of the area described lies in the drainage basin of Pembina river, which flows into Athabaska river. The area to be discussed may conveniently be termed the 'Brazeau area', since Brazeau is the name of the river basin referred to above, of an out-lying limestone range, and of the only large settlement or community in the region, the mining town Brazeau. One of the first Factors of the fur trading post of Rocky Mountain House in the early years of the nineteenth century was Louis Brazeau. Coal mining during the past 25 years, and more recently exploratory drilling for oil, have brought the district into some prominence. The Brazeau area was visited by D. B. Dowling for the Geological Survey of Canada in 1906 and 1907 (1). His traverses and reports dealt mainly with the Kootenay coal deposits. It is doubtful if he traversed the outer foothills area with which the present paper deals. His reports on rich coal deposits in the Bighorn Basin area attracted commercial interests, and in 1908 large tracts were leased as coal lands. James McEvoy mapped and studied the coal seams in that year, and G. S. Malloch, of the Geological Survey of Canada, made a complete survey of the whole of the Bighorn basin. His report (2), published by the Survey in 1911, describes the stratigraphical geology and names the formations. Further references to the geology of the district, mainly in relation to coal, are made by D. B. Dowling (3) and by J. S. Stewart ( 4). In the period between 1913 and 1920, the area was traversed by private interests in search of likely oil structures. A well was started in 1914 along the Saskatchewan river about 19 miles west of Rocky Mountain House, and drilling was undertaken by Imperial Oil, Limited, in 1921 at Coalspur.

Jan 1, 1939