Search Documents

By Garston Blackwell

Abstract - During geostatistical estimation of block grades, the kriging process produces a measure of error, the kriging variance or the kriging standard deviation. Estimation of the block error depends on the semi-variogram model for a deposit, which reflects fundamental characteristics of a deposit such as (1) nugget effect, (2) range of influence of grades, (3) different local spreads of data as a function of average grade (proportional effect), (4) nested structures, and (5) underlying anisotropies in the data; this model may be affected by sampling or assaying limitations, however. Because the kriging error incorporates so many features of both the deposit and data to be used for estimation, it may offer a substantial improvement on block classification over traditional procedures such as data density. Practice indicates that the relative kriging standard deviation (RKSD) is particularly useful for block classification in measured, indicated and inferred categories. Plots of RKSD in plan and section also can be used to demonstrate where extra drilling and sampling would be most advantageous for upgrading the class of some blocks. Moreover, the use of grade and RKSD filters can show where material near cut-off grade is poorly defined, indicating sampling target areas to improve block classification in the vicinity of the ore-waste boundary.

Jan 1, 1998

By A. Haldar

The major problem encountered in the casting of hypereutectic Al-Si alloys is the stoppage of flow below the rigidity level of solid fraction. In this study, the flow stoppage mechanism was studied using three Al-Si alloys with 14%, 18% and 22% silicon. The horizontal foam patterns used were 12.50 mm (0.50 inch) wide with two section thicknesses 12.50 mm (0.50 inch) and 6.25 mm (0.25 inch) with a common sprue. The primary silicon distribution along the length of the casting was studied to determine the mechanism of flow stoppage. It was found that the surface of the flow tip of Al-14%Si alloy was smooth with a few undulations. As the silicon level increased, undulations at the flow tip increased. The number and size of undulations were maximum for the Al-22%Si alloy. Microstructural analysis using optical image analyzer revealed that the flow tip consisted mainly of eutectic silicon in the aluminum matrix and a few primary silicon crystals (PSC). The PSC were in the interlocked condition few centimeters behind the flow tip. It was also found that the gap between the flow tip and the PSC concentrated area increased with an increase in silicon level. Phase characterization was done with SEM-EDX to identify the precipitating phases.

Jan 1, 2007

By I. J. Burgess, B. C. Barlow

"The electrodissolution of nickel pellets with different controlled electrical variables was investigated in an effort to mitigate plating residue in Watts bath based electroplating cells. During galvanostatic dissolution at 0.4 A dm-2, the anode potential was seen to oscillate between passive and pitting potentials. In-situ microscopy and ex-situ characterization has shown that lacy-pit formation and large, partially perforated, pit covers form during the potential decay from pitting potentials. In general, covered pitting at low current density shows increased plating residue. Using potential pulses is one way to maintain greater control over surface pitting by creating a higher density of pit nuclei while at the same time controlling their growth. Pits generated from a series potential pulses were examined ex situ for a range of pulse times and stages of pit growth were identified. An alternative method of anode dissolution was devised using potential pulses and duty cycles that allowed average current densities comparable to industrial plating conditions to be achieved. By restricting the time at pitting potentials to 0.05 s, plating residue was reduced more than six-fold in comparison to an equivalent galvanostatic experiment run at a comparable current density.INTRODUCTIONIn typical galvanostatic (direct current) nickel electroplating cells employing soluble anodes, some amount of plating residue is produced which consists of metallic nickel and impurities that detach from the bulk in the form of small fines. Significant buildup of residue requires plating operations be halted and the anode assembly cleaned of residue before operation can resume. While variables in the refining process have been shown to affect plating residue, more precise control of electrochemical variables may provide an attractive route to mitigation of residue."

Jan 1, 2016

By Madaah Hosseini H. R., P. Abachi, S. Miraghaei

In this study, the effects of milling time, chemical composition and heat treatment on microstructure and magnetic properties of nanocrystalline Fe-Si (6.5-25 at.% Si) alloys prepared by mechanical alloying have been investigated. The results show that increasing the milling time or the Si content, decreases the lattice parameter and increases the internal microstrain. The prepared powders mainly consist of micron-sized particles with an average grain size of less than 20 nm. The specific saturation magnetization values are slightly less than those of single crystal or conventional Fe-Si alloys and decrease as Si content increases. The coercive force values of the nanocrystalline as-milled powders are much higher than those of corresponding Fe-Si bulk alloys with a minimum at 13.5 at.% Si. The values of coercive force decreased after annealing but it seams that the residual strain developed during milling is not the major contributing factor to the higher values of coercive force in the mechanically alloyed powders and nanocrystals behave as single-domain particles without exchange interaction between them.

Jan 1, 2006

By T. Crivits, I. Bellemans, K. Verbeken

In the metallurgical industry, furnace cooling is often employed to enhance furnace lifetime. Hence, the pyrometallurgical phase comes in close contact with a non-air coolant. The proximity of the pyrometallurgical phases to the coolants may lead to dangerous situations. In case of a breach of the cooling circuit, the contact between a hot and a cold liquid may cause a vapour explosion. The outcome of this vapour explosion includes a pressure wave which could result in damage to the furnace, bodily injuries or even casualties. To prevent such dramatic events, the origin of vapour explosions is currently being studied in more detail. For this purpose, OpenFOAM was used to perform Computational Fluid Dynamics (CFD) simulations. In a first step, simulations were run to get a better idea of the influence of the compressibility on the simulations. The obtained results help in getting a better insight on the need of computational power, and possible numerical errors using compressible or incompressible solvers in future simulations. In a second step, systems without vapour explosions were simulated and compared to experimental results with mercury and aluminum. INTRODUCTION Humanity started using metals for tools around the Chalcolitic (~7400 cal BC), when copper was melted in small furnaces (Radivojevic, Rehren, Farid, Pernicka, & Camurcouglu, 2017). Nowadays, metallurgy has grown into a major industry and it has become impossible to imagine society without metals. In the pyrometallurgical industry, coolants (low temperature liquids, for example water) and pyrometallurgical phases (high temperature liquids, such as slags, mattes and alloys) are typically present in close proximity of each other. The interaction between these two phases can have catastrophic consequences (Tveit et al., 2008; Ferguson & Zsamboky, 2017). A vapour explosion may occur as the consequence of the rapid evaporation and expansion of the coolant. Whereas the volume of a gas increases linearly with the temperature (approximately a factor four by heating from 100°C to 1300°C), a simple calculation of the ratio of the two specific volumes shows that evaporation causes the volume of water to increase by a factor of 1700 at 100°C and ambient pressure (Table 1 and equation (1)), a number that was also found in literature (George, Nexhip, George-Kennedy, Foster, & Walton, 2006). The volume change occurs so fast that it resembles an explosion, hence the name vapour explosion. Such an explosion at industrial scale can cause economical losses, bodily injuries or even fatalities.

Jan 1, 2019

By T. Patching

"Introduction The occurrence of coal was first reported in the Drumheller area in 1793 but it was not until 1912 that production of coal was recorded. In that year 13,000 tonnes were mined in the Drumheller area. Three years later the Drumheller mines ranked next in the Province to those in the Crowsnest and Lethbridge districts, with an output of 225,000 tonnes. By 1917 production had increased to 600,000 tonnes, moving Drumheller to second place in output in the province, second only to the Crowsnest district. It held this rank until 1960. Production, almost all from underground mining, rose to over a million tonnes a year by 1920 and remained between one and two million tonnes per year until 1954. Competition from newly discovered oil and natural gas, beginning around 1950 caused a steady loss of domestic coal markets, especially from underground mines. By 1960 Drumheller's production had fallen below a half a million tonnes per year and the field ranked third in output in the province, being surpassed by new stripping operations in the Castor field. By 1965 only a couple of producing mines remained in the Drumheller valley, and output was only about a quarter of a million tonnes per year(1). Throughout the life of the field production was seasonal, depending mainly on the domestic heating market. In 1979 the last mine ceased production. For the last several years of its operation it had remained open in the summers to provide tours for visitors(2). The Drumheller mining operations were located along or near the Red Deer River valley which is 300 to 400 feet deep, and extended from a few miles above the city of Drumheller to East Coulee, about 13 miles down the river in a south-easterly direction. Intervening mining communities existed for some years at Wayne and Rosedale. During the peak years of production some 2000 to 2500 miners and their families lived in these communities and the surrounding areas."

Jan 1, 1985

By Colin E. Dunn

Plants have a remarkable ability to select, use and store metals derived from the substrate. Each species is unique in its requirements for and tolerances to the full spectrum of chemical elements in the Periodic Table. Studies to define the chemical characteristics of common trees and shrubs of the temperate forest are providing insight to their use for exploration, i.e., biogeochemical exploration. Examples of surveys over gold deposits in British Columbia show the effectiveness of sampling various tissues from different species in a range of biogeoclimatic environments. At the Nickel Plate mine in the Montane-Spruce zone, outer bark of Lodgepole pine was effective in defining a large area of metal enrichment; at the Carolin mine in the zone of Coastal Mountain Hemlock, analysis of twigs of western hemlock and Pacific silver fir provided an exploration target considerably larger than that defined by lithogeochemistry; at the Mount Washington gold deposit in the Mountain Hemlock zone, twigs of mountain hemlock and rhododendron were used to outline the mineralization; and in the Interior Douglas-fir zone at the QR deposit analysis of Douglas-fir tops collected by helicopter provided a rapid and effective method of identifying a gold-rich area.

Jan 1, 1995

By Colin E. Dunn

Abstract-Plants have a remarkable ability to select, use and store metals derived from the substrate. Each species is unique in its requirements for and tolerances to the full spectrum of chemical elements in the Periodic Table. Studies to define the chemical characteristics of common trees and shrubs of the temperate forest are providing insight to their use for exploration, i.e., biogeochemical exploration. Examples of surveys over gold deposits in British Columbia show the effectiveness of sampling various tissues from different species in a range of biogeoclimatic environments. At the Nickel Plate mine in the Montane-Spruce zone, outer bark of Lodgepole pine was effective in defining a large area of metal enrichment; at the Carolin mine in the zone of Coastal Mountain Hemlock, analysis of twigs of western hemlock and Pacific silver fir provided an exploration target considerably larger than that defined by lithogeochemistry; at the Mount Washington gold deposit in the Mountain Hemlock zone, twigs of mountain hemlock and rhododendron were used to outline the mineralization; and in the Interior Douglas-fir zone at the QR deposit analysis of Douglas-fir tops collected by helicopter provided a rapid and effective method of identifying a gold-rich area.

Jan 1, 1995

By Mohammed Rachek

Résumé : la mine d?Elhammam, opération du groupe minier Marocain Managem, est située au sud de la ville de Meknes à 63 km, elle exploite un gisement de fluorine depuis 1974. La minéralisation se présente sous forme de deux filons principaux orientés N45° avec un pendage variant de 65 à 90° NW, entre ces deux filons on note la présence d?une succession de filons satellites sécants. La méthode d?exploitation pratiquée depuis le démarrage de la mine est celle des chambres magasins, elle assure une cadence d?extraction annuelle de 250000 tonnes. Cette méthode favorisée par une très bonne compétence mécanique des épontes de la minéralisation a offert à l?exploitation une rentabilité très satisfaisante grâce à son faible coût mine. Les travaux de recherche géologique menés en parallèle à l?exploitation ont permis la découverte d?un nouveau secteur ?K-Est Gouaïda? (KEG) qui fait l?extension nord-est du gisement principal, la minéralisation de ce secteur se présente sous forme de deux filons très étendus latéralement (900 m d?extension) et présentant une puissance minéralisée irrégulière et très faible 1.2 m en moyenne, les épontes de la minéralisation sont constituées de schistes de qualité mécanique très faible. Vers la fin des années 1990, l?exploitation s?est orientée vers le développement minier du secteur KEG. Ce développement consiste à faire le choix adéquat de la méthode et de l?infrastructure minière pour l?exploitation de ce nouveau secteur, KEG. La méthode des chambres magasins, pratiquée dans le gisement principal avec un faible coût mine, n?est pas praticable dans le nouveau secteur à cause de la qualité de ses terrains, l?irrégularité de la morphologie de sa minéralisation et de la faible puissance des ses filons. Seule la méthode des tranches montantes remblayées (TMR) peut être applicable techniquement vu les spécifications suscitées de la nouvelle minéralisation, la TMR doit être appliquée sous sa variante mécanisée pour faire face au niveau exigé de la production. Après le pilotage de l?exploitation par TMR mécanisée dans le secteur KEG, il a été confirmé que cette méthode donne une grande satisfaction en matière de stabilité des terrains, sécurité, sélectivité, productivité et récupération du gisement, néanmoins elle reste pénalisée par un coût mine trop élevé pour garder le niveau de rentabilité recherché par l?exploitation d?un produit de faible valeur marchande telle que la fluorine. Dans l?objectif de rentabiliser l?exploitation du secteur KEG qui représente en réserves l?équivalent d?une durée de vie de 4 à 5 ans et d?assurer la pérennité de l?activité, l?exploitation en collaboration avec Reminex, la filiale d?ingénierie de Managem, a adapté une nouvelle variante de la TMR mécanisée dite TMR avec plan incliné sur remblai. Cette nouvelle variante de la TMR consiste à réduire au maximum les travaux dans le stérile en reconstituant un plan incliné sur le remblai à l?intérieur des filons pour faire évoluer en vertical l?exploitation des tranches en montant vers la tête d?un panneau de minerai. La variante des tranches montantes remblayées mécanisées avec plan incliné sur remblai a été imaginée et appliquer en 1978 dans la mine de fluorine de Burc située au Sud-Ouest de la France (Sicard et Mailloux, 1983). Imaginée pour une cadence annuelle de 30000 tonnes et une mécanisation très modérée cette variante a été adaptée par l?exploitation de la mine d?Elhammam en 2002 pour un haut degré de mécanisation et une cadence d?extraction annuelle de 250000 tonnes de minerai. Cette variante de la TMR est appliquée depuis le début de 2003 dans les chantiers du secteur KEG, elle présente les mêmes avantages techniques que la TMR mécanisée classique et elle a permis la réduction du volume des travaux d?infrastructure de 17.65 m à 6.25 m de travaux par 1000 tonnes de minerai. Ceci s?est traduit par une baisse du coût technique de la mine de 34% ce qui a donné un nouveau souffle à la mine pour assurer sa production et pour poursuivre la recherche géologique d?éventuelles zones à mettre en valeur.

Oct 1, 2004

The Red Lake greenstone belt is an irregular mass of lavas sedimentary rocks and intrusives which is approxiately 35 miles long 18 miles wide and 7 miles deep. Basaltic volcamcs are the oldest rocks w1thm the belt. They are believed to have been laid down on an ancient crust which is at least 3 billion (3 x 109) years old and was composed partly of sediments. The basaltic rocks are overlain by acid volcanics and sedimentary rocks which have been complexly folded and are preserved as a down-folded remnant of younger rocks within the older crust. The volcanics and sedimentary rocks of the greenstone belt have been cut by intrusives with a wide range of composition. The emplacement of the intrusives and the accompanying regional metamorph-ism which terminated the orogenic activity in this area are believed to have occurred approximately 2.4 billion years ago. The basalts and many of the basic and ultrabasic intrusives undoubtedly had their source in the sub-crust or mantle. At least some of the granitic intrusives are believed to have had

Jan 1, 1965

By A. Chieregato, C. G. Oñate Salazar, D. Martinelli, D. Peila, M. Barbero

This paper is aimed to confirm the possibility to excavate fractured rock masses by using EPB shields, even in presence of relevant water tables. This verification is based on laboratory test experiences carried out at TUSC laboratory of Politecnico di Torino, where the natural material is tested in order to verify the suitability of a certain conditioning technique in particular conditions. This is due to the fact that every case should be studied apart from existing studies on a certain rock type, as other factors such as fragmentation of the rock mass, natural water content and porosity of the rock can considerably influence the final result of the conditioning process. The most important aspects that allow to consider the conditioning of fractured rock masses as suitable are: possibility to create a plastic paste that can transmit the pressure at the front in a effective way; reduce the permeability of the spoil material in order to reduce the possibility of water leakage inside the chamber and eventually in the tunnel; verify the consistency of the conditioned material for the extraction through the screw conveyors and the belt conveyors. For this research an argillitic schistose rock mass, with some quartzitic and calcareous inclusions, has been studied by using different level of conditioning in order to verify the suitability of an eventual EPB excavation through this formation.

Jan 1, 2015

By A. McLean, L. Gao, Z. Shi, Y. D. Yang, K. Chattopadhyay, G. F. Zhang

Levitation melting of metals is one of the emerging applications of magnetic and electric fields in liquid metal refining. The varying magnetic field generates induced current inside the metal droplet and leads to the Joule heating effect and Lorentz force against gravity. This contactless process can avoid contamination from the crucible and can be used to produce high-purity materials. Visualization of the levitation melting process is difficult, and thus generally investigated by mathematical modeling. In the present study, a three-dimensional mathematical model of metal levitation was developed using finite element method for proper understanding of the levitation process. The effects of harmonic magnetic field frequency, coils power input, and sample size on levitation nickel droplet were investigated. Temporal evolution of temperature fields were predicted directly though the model. Levitation and balance condition of the droplet were investigated as well.

Jan 1, 2015

By I. H. Warren, F. A. Forward, A. Vizsolyi

"Observations are reported on the pressure leaching of material produced by subjecting chalcopyrite to two types of heat treatment. Calcination of the mineral at 825°C, in the absence of oxygen, induces some sulphur loss by volatization, producing a material from which copper can be leached more rapidly than from chalcopyrite. Treatment of the mineral with elemental sulphur at 475°C leads to sulphur uptake accompanied by a change in mineralogical structure of the chalcopyrite. Copper is prefer-entially and rapidly leached from the sulphur-treated material. A tentative explanation of the sulphur-chalcopyrite re-action is presented."

Jan 1, 1968

By Hooman Askari-Nasab

Open pit mine plans define the complex strategy of displacement of ore and waste over the mine life. The objective of the mine plan is to maximize the future cash flows within the technical and physical constraints. Various mixed integer linear programming (MILP) formulations have been used for production scheduling of open pit mines. In the MILP formulation the slope constraints guarantee that all the overlying blocks are mined prior to mining a given block. Traditionally, the slope constraints have been modeled with cone templates representing the required wall slopes of the open pit mine. The overall pit slopes constructed by these templates are a function of the width and height of the geological block model. Therefore, the overall slopes are fixed in one bearing. This paper presents a general MILP model for open pit mine scheduling with variable slopes constraints. The methodology utilizes a directed graph to capture the precedence of extraction of blocks and pit slopes in different bearings. Depth-first-search algorithm was used to traverse the graph for constructing the slope constraints in the MILP problem. TOMLAB/CPLEX was used as the implementation platform to efficiently integrate the mathematical solver package CPLEX with MATLAB. A case study on intermediate scheduling of an iron ore mine over twelve periods was carried out to validate the models.

Oct 1, 2009

By K. Shikaze

"For the last three years (1967-9) the value of the output of mineral resources in the Province of Ontario exceeded one billion dollars per year. To produce this great wealth, it was necessary for the mining industry in Ontario to dispose of an estimated 80 million tons of waste mill tailings. Some of these tailings were returned underground but the greater proportion was disposed of above ground in lakes, watercourses, marshy areas and in engineered impoundment basins. This volume of tailings, if accumulated in one location would cover an area of 1000 acres to a height of almost thirty feet. The provision of proper disposal of the waste mill tailings in a manner such that they will not create problems in the environment is one of the costs which must be borne from the extraction of such a wealth from our mineral resources. It is principally the potential water pollution which may occur as a result of the indiscriminate discharges of waste mill tailings which is of concern to the Ontario Water Resources Commission.ONTARIO WATER RESOURCES COMMISSIONThe Ontario Water Resources Commission was formed in 1956 and operates under the Ontario Water Resources Commission Act. The Act has been broadened and amended many times by amendments."

Jan 1, 1970

By Matthew S. Hall

Gold/iron oxide catalysts have been prepared and their catalytic performance evaluated for low temperature CO oxidation. The method and temperature used to dry the sample has a significant effect on their catalytic activity. Analysis by TEM revealed the catalysts contained Au particles, although catalysts with high and low activity did not always differ in their microstructure as evidenced by TEM. Catalysts were characterised using XPS and the difference between the Au(4d) and C(1s) binding energies measured; in general the greater the difference, the higher the catalytic activity of the material.

Oct 1, 2003

By A. Tikhonov, D. Kipper, V. Korovin, A. Olifirenko, Yu. Shestak

The present paper deals with vanadium and molybdenum sorption from industrial wastes and intermediate processing products using Cybber macroporous strong- and weak-base anionites. Vanadium and molybdenum recovery by Cybber anion-exchange resins as well as desorption processes were studied in static and dynamic modes; their efficiency was demonstrated for that purpose. The results of the work may be used to design technologies for complex processing of both ores and industrial wastes containing vanadium and molybdenum.

Jan 1, 2011

By Lloyd Buckingham

"The operating cost of a gold mine employing granular activated carbon to recover gold can be greatly affected by the condition of in-circuit carbon and its attrition losses. To accurately identify and quantify carbon losses requires careful study. Carbon attrition in the mill can be attributed mainly to physical or mechanical breakage due to the transfer of carbon in the circuit and to carbon oxidation and thermal fracture occurring in the carbon reactivation kiln. Of the equipment involved in carbon transfer, the water powered eductors are the major cause of abrasion and should be replaced with pumps or alternate methods that can serve the purpose. This paper also reviews the impact of carbon stripping and washing on overall operations.IntroductionHolt-McDermott Mine operates a 1360 tonnes per day Carbon-in-Leach (CIL) mill to recover gold. The relatively high carbon consumption and high remaining gold values on carbon after stripping were viewed as a challenging project for research. Extensive metallurgical testwork was initiated to reduce these values. Figure 1 below indicates the carbon flowchart prior to any significant changes in the carbon handling procedures.Carbon consumption after commissioning which was as high as 10""/o of carbon eluted, has been brought down to less than 5%. Changes that brought about this 50% reduction in carbon consumption are:1 ) Improvements in kiln operation2) Elimination or replacement of eductors3) Reduction in tonnes of carbon eluted"

Jan 1, 1994

By Todd Kennedy, Kurt Tischler

"This paper presents the field experience of Siemens with regard to Gearless Drives in the mining industry … We consider the elapsed production hours of Siemens Gearless Drives to be extensive enough to provide a reliable estimation of availability calculated on the basis of data representing repair time, downtime, and operating time. The users of Siemens Gearless Drives confirm an availability of more than 98% after exclusion of some major issues. The paper addresses all of these major issues of Siemens Gearless Drives, describes successfully applied corrective measures, explains the influences on the design of the drives, and lists the downtimes associated with each of these issues. INTRODUCTIONThe first Siemens Gearless Drive in mining began operation in 1980 and was installed on an iron ore grinding mill. As of September 2011, 40 Siemens Gearless Drives will have accumulated 136,000 machine days of operating time. According to pure rules of statistical analysis, this accumulated operating time may be too low to be used for a sample of field data to provide precise statistical values of availability, however we consider it large enough to provide indicative values of worthwhile consideration. This paper deduces the availability statistics of Siemens Gearless Drives in the mining industry from information received from end users and factors in all major issues that Siemens has experienced with our Gearless Mill drives. This paper does not consider Gearless Drives in other industries such as the cement industry. The cement plants, especially in the northern hemisphere, interrupt production for several months in the winter. This lengthy downtime is used to maintain the complete plant including the mills, their motors and their drives. The mining industry has more stringent and higher production requirements. In the mining industry, production must run 24 hours per day, 365 days a year."

Jan 1, 2012

By C. Arson

We modeled mode I fracture in shale with an equivalent damage zone (CDM), a cohesive zone (CZM) and discontinuous enrichment functions (XFEM). In the Differential Stress Induced Damage model (DSID model) used in the continuum approach the total work input is equal to the sum of the energy released by crack debonding, the energy dissipated by crack opening, and the elastic strain energy stored in the bulk outside of the damage zone. In CZM and XFEM, the overall stiffness of the rock mass in the process zone drops as soon as the fracture starts propagating (unstable fracture propagation), whereas rock elastic properties in the CDM equivalent damage zone evolve smoothly with the displacement imposed at the boundary of the domain. In the CZM and XFEM, fracture propagation stabilizes after a turning point: this point coincides with damage initiation in the DSID model. As a result, the total energy of the rock mass calculated with CDM is about twice as large as in CZM and XFEM. The relative energy components of the rock mass are in the same order of magnitude and follow the same trends in the three models. This numerical study compares the evolution of dissipated energy potentials during mode I fracture propagation, and is expected to provide a basis to predict the amount of energy released by discrete fracture growth vs. damage propagation in the fracture process zone.

Jan 1, 2015