Search Documents

By F. Roemer, D. Goldmann, T. Elwert

Tantalum is an important minor metal for the production of high performance capacitors. Approximately 60% of the annual tantalum production is used in this application. Despite its high price of 298 US$/kg (average price 2010–2014), at the moment, no recycling from end-of-life products takes place. In the established recycling processes of waste electrical and electronic equipment (WEEE), tantalum is lost in the slags of copper smelting, where it is highly diluted. An economic recovery is not possible at that point. Although tantalum must therefore be extracted from the WEEE stream before it enters smelting, no industrial recycling processes exist. The main reasons are its low concentration in the WEEE stream, lack of information about tantalum bearing devices, technical difficulties of extraction, and conflicts of interests regarding the recycling of other valuable metals in WEEE. In this paper, the results of a cooperation research project are presented. The aforementioned challenges are addressed and a novel tantalum recycling process is developed. Small pilot scale experiments show that a mechanical processing route can produce marketable tantalum-concentrates of 30% tantalum with yields between 60 and 70%. This is reached through a manual pre-sorting of potentially tantalum bearing products followed by a combination of an optimized comminution, sieving, air classifying, eddy-current (EC), and two stage magnetic separation. Key to the implementation of this process was a detailed survey of the tantalum concentrations in different products carried out by the industrial partner.

Jan 1, 2016

By D. D. Campbell

The Hat Creek coal deposit s occur within folded and faulted Tertiary (Eocene) strata of the Coldwater Group, which comprises weakly lithified shales, siltstones and conglomerates underlying the floor and lower flanks of the valley of Upper Hat Cr eek . This upland valley,16 miles in length and 2-4 miles in width, is located within the eastern foothills of the Coast Mountains, 120 miles northeast of Vancouver, approximately midway between the towns of Lillooet and Ashcroft, in the Interior Dry Belt of British Columbia . Most of the valley floor is covered by till and glacial outwash deposits ranging up to 500 feet in depth. Became of this overburden cover , the majority of the data on the coal deposit have been obtained from diamond drilling done during 1974?76 by the property owner, B .C. Hydro and Power Authority. Because of the limitations imposed by the lack of out crop, the Tertiary geology at Upper Hat Creek is imperfectly known; however, it appears from correlation with other coal-bearing Tertiary remnants in the southern interior of the province that these remnants, including Upper Hat Creek, may represent preserved segments of the western shoreline of a Tertiary continental sea along which deltaic swamps developed and were sustained for unusually long stable periods, giving rise to the world's thickest known coal beds.

Jan 1, 1977

By Rodolfo Zanella

Au/TiO2 catalysts prepared by deposition-precipitation with NaOH (DPN) (~3 wt%) and urea (DPU) (~8 wt%) were tested in crotonaldehyde hydrogenation at atmospheric pressure. There is no differences in activity (mole.gAu -1 s-1) and selectivity between both DPU and DPN samples for a given activation treatment. This is due to the fact that DPU and DPN samples exhibit similar gold particle size distribution, although the gold loading in DPU is much higher that in DPN. The DPU samples were reduced under H2 at different temperatures (120-500 °C) or under air at 300 °C with various flow rates, to vary the average particle size within a large range, 1.7 to 8.7 nm. The selectivity to crotyl alcohol (selective hydrogenation of the carbonyl bond) is high, 60-70 %, and almost constant as a function of the particle size. The selectivity to crotyl alcohol is also constant for conversions between 10 and 50%. These results suggest that the adsorption mode of crotonaldehyde is of ?3 or ?4-type. In contrast, the TOF depends on the gold particle size, it drastically increases when the gold particle size is ~2 nm. Our results are in agreement with former studies that suggest that the gold atoms involved in the hydrogenation process are those of low coordination.

Oct 1, 2003

By A. G. Pathan

Rock and soil mechanics investigations were carried out in block VIII at Thar Coalfield, Pakistan. Most of the strata were mainly composed of sand, with an average content of 67.68 %. Laboratory studies of rock and soil samples from drill hole GT-01 revealed that the strata in block VIII are very weak with an average uniaxial compressive strength of 3.59 MPa, an average tensile strength of 0.68 MPa, an average Young?s Modulus value of 0.234 GPa, an average cohesion of 129.19 KPa, and an average friction angle of 55.47°. Slope stability analysis, based on a probabilistic approach, was carried out using Slide-V software. Monte Carlo simulations have been applied to investigate the probability of failure in the slopes of an open pit lignite mine in block-VIII. From the slope stability investigation, it was found that the probability of failure is 0 % at a slope angle of 16°.

Aug 1, 2013

By K. Ilankoon, I. M. Saman, S. J. Neethling

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behaviour is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. The particle properties such as size, shape and porosity are very important when modelling the liquid holdup and flow within heaps, since the dominant mechanisms at work are quite different. This paper investigates the effect of these particle properties experimentally on heap flow behaviour using a 1-D column leaching system consisting of non-porous glass beads with a system of actual ore particles. The similarities and differences between the two systems on flow behaviour are described using an inter-particle flow model. In addition, the applicability of positron emission particle tracking (PEPT) for laboratory column leaching will be detailed to calculate hydrodynamic dispersion in packed beds compared to more conventional residence time distribution (RTD) tests and also to obtain the time averaged rivulet flow paths through the particles of the bed for the better understanding of heap hydrodynamics.

Jan 1, 2014

By S. P. Lowe

Flotation testing of Flin Flon ore was started in the Denver laboratory of Complex Ores Recoveries Co. in March, 1926. There had been a considerable amount of flotation testing previously which had shown possibilities of success, and it was felt that, with the increased knowledge of flotation and the comparatively new reagents then available, flotation held out the best prospects for a successful commercial treatment of this ore. There remained available for this experimental work a small amount of the rejects from a thorough sampling of the mine and some ore from the mine dump.

Jan 1, 1930

By A. A. McCloskey

APPROXIMA TEL Y 95 percent of Waite-Amulet's Lower A orebody will be mined by diamond-drill stoping. This method of stoping was developed, and has been successfully applied, at the Noranda mine in recent years(1) and is now used in several base-metal and gold mines in north-western Quebec and in other parts of Canada, South Africa, and Australia. The purpose of this paper is to deal with the features of the Lower A ore-body which led' to the adoption of this method of stoping, and in addition to give a general description of stope layout, stope development, main haulage development, chutes and grizzlies, diamond drilling for stope blasting, diamond drilling and equipment, primary blasting, secondary blasting, haulage and loading, ore pockets, pumping and drainage,. and shafts at Waite Amulet. Figure 1 is an isometric projection of the orebody, illustrating the mining system. The factors that led to the adoption of diamond-drill stoping of Lower A orebody are as follows: (1) Safety.0 (2) Size and shape of the orebody, and depth of the orebody below surface. (3) Strength of the hanging-wall, footwall, and sulphide ore. (4) Continuous ring-drilling from sub-level drifts, with no delay for blasting. (5) Large-tonnage blasts at the end of Saturday afternoon shift, after ali men are out of the mine. (6) Sub-levels may be retreated from top to bottom simultaneously, or lower sub-levels may be retreated first without any change in the ring-drilling la yout. (7) Large stopes up to 100 feet wide can be mined, leaving substantial pillars up to 60 feet in width, which may be partially recovered by âiamond~drill stoping or by other stoping methods. (8) A large tonnage may be drilled-off in advance of blasting, but only a supply of unoxidized ore for flotation treatment is blasted. (9) Better ventilation during working shifts. (10) Gravity flow of all broken ore to grizzlies located in the footwall of the orebody. (11) Electric blasting by a crew of two men.

Jan 1, 1941

By J. E. Dutrizac

The dissolution of low-iron sphalerite, (Zn,Fe)S containing 0.08% Fe, in ferric sulphate-sulphuric acid media was investigated using closely sized fractions of crushed sphalerite crystals and sintered disks made from the crushed crystals. Linear kinetics are observed, and the predominant reaction products are ZnSO4, FeSO4 and elemental sulphur. The leaching rate increases systematically with increasing temperature, and the calculated apparent activation energy is 56 kJ/mol for the sized sphalerite and 54 kJ/mol for the sintered disks. The relatively high apparent activation energy suggests that the rate is chemically controlled, a conclusion supported by the insensitivity of the rate to the disk rotation speed. The rate increases as the 0.22 power of the Fe(SO4)1.5 concentration, and as the 0.22 power of the H2SO4 concentration. However, in the absence of ferric ions, the rate increases more significantly with increasing H2SO4 concentrations, and relatively rapid rates are observed in solutions containing >0.5 M H2SO4. In 0.1 M Fe(SO4)1.5-0.3 M H2SO4 media, the measured rate decreases with increasing sulphate concentrations, added as Li2SO4. The rate of dissolution of low-iron sphalerite is promoted by dissolved copper concentrations as high as 800 mg/L. In contrast, dissolved silver, even in the 0-2 mg/L concentration range, significantly retards the dissolution of the low-iron sphalerite.

Jan 1, 2008

By L. A. Ayres da Silva, J. P. G. Negri, A. L. M. Ayres da Silva

"Rock hardness is dependent on the type and quantity of the various mineral constituents of the rock and the bond strength that exists between the mineral grains. As the book “The Complete ISRM Suggested Methods For Rock Characterization, Testing and Monitoring:1974-2006” explains, hardness is a concept of material property. As such, the quantitative measure of hardness depends on the type of the test employed.Among the three types of tests that have been used to measure the hardness of rocks and minerals: 1) indentation tests; 2) dynamic and rebound tests; 3) scratch tests, the authors of this paper chose indentation tests, more specifically the Vickers test, and complementary verified the correlation between the results of the Schmidt sclerometer tests (rebound tests) and the Vickers microhardness tests in a set of the same 9 (nine) granite rocks.The objective of this research was to verif y the correlation of one created index, based on the Vickers test that can be able to represent the rock material hardness. We know that Vickers tests determine the microhardness of individual rock minerals. A pyramidal shaped diamond is applied to the surface with a specified force. The area of the permanent residual deformation divided by the applied force is a measure of the hardness. Using the relative participation of the mineral components of the rock, we established a hardness index denominated EVM (Equivalent Vickers Microhardness).The correlation of the EVM with others strength properties and application parameters like UCS (Uniaxial Compressive Strength) to study sawability of granite blocks have presented very good results. The association of equivalent microhardness with others strength parameters, allowed to find powerful algorithms for analyzes of the rock materials behavior under diversified circumstances, as the sawability of granite blocks, as we can see in Fig. 1.Other very interesting correlations were found as the EVM values and that were obtained by the use of the Schmidt impact hammer for the superficial hardness determination."

Jan 1, 2015

By X. -P. Zhang, L. N. Y. Wong

Shale gas exploitation initiated in North America has rapidly extended worldwide. Hydraulic fracturing is an emerging field technique for stimulating the gas reservoir. The study of cracking processes, particularly crack coalescence, is vital for a successful hydraulic fracturing to enhance the gas exploitation. Experimental studies have observed that the size effects of the constituent particles are significant on the cracking behavior of the rock specimens. To further investigate the size effects, the bonded-particle model (BPM), which is based on the discrete element method (DEM), is adopted in the present research. In flaw-containing specimens, by varying the crack resolution (?= a/2R), which is the ratio of half flaw length (a) to particle size (2R), the size effects on cracking behavior under compressive loading are studied. By keeping the flaw length constant, the particle size is varied independently in the BPM analysis. Decreasing the crack resolution increases the first crack initiation stress, but it has no obvious effects on the uniaxial compressive strength. The trajectories of the first cracks and secondary cracks hence generated have a higher resolution and are well-defined in those specimens possessing a higher crack resolution. On the contrary, in lower crack resolution specimens, the macroscopic first cracks appear to be wider and less continuous. These findings from numerical simulation clearly demonstrate particle size effects on cracking behavior. Special attention should be paid to these effects in future numerical study using the bonded particle model.

Jan 1, 2015

By Niraj Bala

Boiler tubes of coal-fired boilers suffer severe erosion-corrosion (E-C). One method to counteract this problem is by the use of therma, spray protective coatings. Cold spray coating process was used to deposit Ni-20Cr powder on SA 516 (Grade 70) boiler steel. The bare as wel, as the coated steels were subjected to cyclic experimenta, studies, in the superheater zone of a coa, fired boiler. The weight change technique was used to establish kinetics of the erosion-corrosion. XRD, FE-SEM/EDS and X-ray mapping techniques were used to analyse the as-sprayed and corroded specimens.

Jan 1, 2010

By R. O. Burt

The original flowsheet of the TANCO mill consisted of a simple two-stage gravity circuit for the recovery of the tantalum concentrates. With decreasing grade and grain size of the tantalum minerals, considerable modifications to the circuit have been required. This paper discusses the various recent improvements carried out 011 all stages of the flowsheet, which have resulted in a 10% increase in recovery. Future improvements, including on stream analysis, and the possibility of tantalum flotation , are also discussed.

Jan 1, 1979

By M. T. Shehata, R. W. Revie, M. Elboujdaini

Environmentally assisted cracks in linepipe steels are initiated either as a result of stresses in combination with environmental effects, as in stress corrosion cracking (SCC), or as a result of trapped hydrogen in the steel, as in hydrogen-induced cracking (HIC). To understand better the mechanism of the crack initiation process, key metallurgical and environmental elements that can affect the cracking phenomena were investigated and are reviewed in this paper. The complexity of both cracking phenomena results from the dependence of SCC and HIC on multiple metallurgical, mechanical, and environmental parameters that may all influence both crack initiation and propagation; e.g., composition, microstructure and non-metallic inclusions in the steel, applied stress, water chemistry in the field, and ionic concentrations in the groundwater near the pipe surface to name a few for SCC. In addition, for HIC phenomena, one can add the concentration of H2S in the fluids transported in the pipe as well as concentration of CO2, pH, etc. In this paper, cracking of linepipe steels is analyzed critically, with particular attention to the crack initiation process. The paper is divided into two parts: The first part covers SCC and the second covers HIC.

Jan 1, 2005

By J. Dubinski

Underground mining of copper ore in the Legnicko-Glogowski Copper District basin generates a number of seismic events, whose energy often exceeds 108 J (Butra, 2010). The number of tremors and their location shows that the area of rock mass involved in the deformation and failure processes significantly exceeds the area of mining operations. Locations of seismic foci of high energy tremors, as well as the aftershocks that accompany them, extend hundreds of metres, confirming that processes to restore the energy balance of rock mass occur in a short amount of time and over a wide area. Thus, an area of similar size should be considered in predictive analyses of the tremor?s position. It should be emphasized that a large portion of the rock mass still has a level of freedom resulting from the way the rock mass is held together and its geometric continuity. This level of freedom is dependent on the scale and duration of mining, the number and size of natural structures, and rock mass pressure, including gravitational pressure constricting individual fragments of rock mass in the area (Burtan, 2012). It can therefore be assumed that in real conditions, areas where mechanical strength of the layers has been exceeded may be located a considerable distance from each other and do not necessarily need to coincide with the working area location. In this sense, a rock mass influenced by mining exploitation is essentially a rock mass in which numerous fragments with concentrated energy exist simultaneously. Energy will be released within these rock mass areas each time rock mass strengths are exceeded by the induced stress changes related to mining operations. This paper presents a discussion on how to predict the location of seismic activity areas based on a change of position of seismic energy equivalents. This parameter is calculated for a given set of seismic tremors with defined foci coordinates. For a given set of seismic tremors, the location of seismic energy equivalents may be used for predicting the location of high-energy seismic events.

Aug 1, 2013

By M. E. Holuszko

A research program has been carried out at the Mining Department of the University of British Columbia to study the effect of wettability of coal on its handleability and bulk density. The effect of moisture content on the bulk density of coal was found to be more pronounced for hydrophilic coals than for hydrophopbic ones. Altering wettability of coal surface leads to different effects of moisture on bulk density. The samples were studied at different fine fractions content, and it was shown that there was no effect of increased content of fines on the bulk density for hydrophobic coals, while for hydrophilic coals this effect was very significant. It was shown that the moisture content at which the lowest bulk density was reached coincides with the critical moisture content for studied samples, as determined from handleability tests using Durham Cone method. This critical moisture is the moisture content at which a sudden deterioration of coal handleability occurs. Based on the bulk density and handleability tests, the flow theory of moist coal is proposed.

Jan 1, 2006

By Mahmood Alemrajabi, Ake Rasmuson, Kerstin Forsberg, Kivanc Korkmaz

"In the present study, the recovery of rare earth elements (REE) in the nitrophosphate process of fertilizer production is investigated. The apatite has been recovered from iron ore tailings by flotation. After digestion of apatite in concentrated nitric acid, Ca(NO3)2.4H2O is first separated by cooling crystallization and then the REEs are recovered by precipitation. Optimum conditions in these steps have been determined in a previous study. The precipitate mainly consists of CaHPO4.2H2O and REE phosphates.In the present study, selective dissolution and re-precipitation have been studied in order to obtain a precipitate that is more concentrated in REEs. The precipitate was selectively dissolved in nitric and phosphoric acid at different acidities (pH 6 to 0) with the liquid /solid ratio of 100 mL/g. It is shown that most of the CaHPO4.2H2O and other calcium containing compounds will be dissolved at pH 2 while the REE phosphates are not dissolved above a pH of approximately 2. Thus, by partial dissolution of the REE precipitate at pH 2.5 most of the solid calcium phosphates will be dissolved and the remaining solid phase, which is more concentrated in REEs, can be filtered off as a fairly concentrated REE solid mass and the liquor can be recycled back to recover more P nutrients. Alternatively, the REE enriched precipitate was dissolved completely in nitric acid and re-precipitated again by addition of ammonium hydroxide to pH 1.2. A chemical equilibrium software, MEDUSA (Puigdomenech, 2013) has been used to evaluate the experimental results and to estimate the optimum conditions for selectively dissolving the precipitate."

Jan 1, 2016

By M. M. Helm

Samples sourced from the Goldstrike property in Nevada USA, have been evaluated in terms of their preg-robbing capacity and the physical structure of the graphitic carbon component in the carbonaceous gold ore. The study highlights a wide range in preg-robbing capacity between samples collected from the Betze-Post open pit and Rodeo underground mine. The physical structure of the graphitic carbon was assessed using Raman spectroscopy, and is found to play an important role in influencing preg-robbing behaviour. Differences observed in the physical structure of graphitic carbon are thought to be the result of hydrothermal events that occurred at Goldstrike.

Jan 1, 2011

By P. J. Le Roux

"Mining worldwide and definitely in South Africa, is constantly under pressure to reduce its cost structure so as to sustain profitability. In underground gold mines where an open stope mining method is employed, dilution often has a significant effect on the viability of sustaining profits. Target Mine practices Open Stope mining Method and it was found that in some open stopes dilution was in excess of 10%, which has a significant impact on the sustainability of the mine.Dilution in excess of 10% can result in the reduction of the recovered grade from 5,5 to 4,5 grams per ton (g/t). The reduction of 1 g/t in recovered grade results in a potential loss of about ZAR21 Million per month bases on a gold price of ZAR240 000 per kilogram. Based on Life of Mine projections the potential loss of income could be as much as ZAR3,3 Billion. A reduction in dilution would have the opposite effect. There are a number of factors which affect dilution of which falls of ground in open stopes is a major contributor. The falls of ground can be attributed to a number of factors such as beam failure as a result of a larger than normal expected roof area (hydraulic radius too large), poor ground conditions, and poor blasting. The cost of damage to or loss of trackless equipment as a direct result of the falls of ground in open stopes, is very significant. The review of financial figures has indicated that this could be as high as ZAR491 million. This combined with the added cost of transport, hoisting, secondary blasting, milling and plant treatment costs of ZAR293 results in an estimated opportunity loss of ZAR784 million.Currently there is a significant amount of data available in the mining industry which could be effectively used to develop suitable back analysis techniques but to date this has not been used effectively. If dilution can have such an impact on current and future mining ventures then the optimization of back analyses for the prediction of dilution in open stoping could assist significantly in the reduction of dilution in massive open stopes. Rockmass classifications, geotechnical information, blast techniques, blast design, the stress strain environment and hydraulic radius all have an effect on, or play a role in the evaluation of dilution. Each of these factors will be taken into consideration to ultimately determine a measurable or calculated percentage of dilution in massive open stopes.The amount of overbreak in an open stope can be determined by subtracting the planned stope volume in m3 from the actual measured final stope volume in m3, which is obtained from the CMS (cavity monitoring system). This is in turn divided by the planned stope volume in m3 to determine the percentage overbreak. The CMS wireframe is imported into the geological model and its grade re-evaluated. From this the actual percentage dilution for this open stope can be determined. The dilution obtained can result in a major reduction of recovered grade for the open stope, but can also increase the recovered grade. The latter is normally the exception rather than the rule.When analysing data from Target mine the following was achieved:• Using 11 years of data a method of measuring and predicting the percentage dilution in open stoping was developed. This took into account rock mass quality, stress-strain state, and the hangingwall hydraulic radius (size of stope hangingwall exposed).• Implementation of this prediction method resulted in a reduction in falls of ground in open stopes. The benefit of this was a reduction in the damage to mechanised equipment resulting from less falls of ground which had a positive effect on the profit margins of the mine. As a direct result the recovered grade from the open stopes increased due to the reduction in the amount of dilution.• A design criterion, Dilution Stress-Strain Index (DSSI), was developed which allows the user to calculate, with certainty, the stability of the open stope and determine if m"

Jan 1, 2015

By Josée Dartois

En 1988, à l?instar de plusieurs états du monde industrialisé, le Québec décidait d?accélérer la cadence de l?assainissement des rejets industriels et lançait un programme intégré de réduction de la pollution industrielle visant, à la fois, les rejets dans le milieu aquatique, les émissions atmosphériques et les matières résiduelles. Ce programme fut intitulé le Programme de réduction des rejets industriels.

Nov 1, 2002

By R. Khettabi

The mechanical, thermal and bioproperties of titanium alloys allow their wide use in different industries. Compared to aluminum alloys, titanium alloys are very tough, making them that much more difficult to machine than aluminum alloys. Most studies conducted on these types of materials have mainly covered and made comparisons in terms of cutting speed, cutting force and mechanical properties. Recently however, their sustainability and environment parameters have begun to attract significant interest, and it has been found that machining processes generate particles that can be harmful for health and the environment. In this paper, particle emission is investigated during the turning of the titanium Ti6A14V and 6061-T6 aluminum alloys.

Jan 1, 2011