Search Documents

By M. P. Sinha, Rashmi, Tata Steel Ltd., S. Jaiswal, A. Bhatnagar, P. Garg

Reagents form a crucial part of flotation process as they have the power to control the surface properties of minerals. In case of coal flotation, collectors and frothers are two the important and commonly used reagents. But other types of reagents such as promoters, modifiers and depressants are also finding wide applications because of their availability to improve selectivity and increase recovery. Because of these chemicals the scenario has changed from flotation being used mostly for high rank hydrophobic coals to low rank, oxidised or inferior coals. In the present work a case is presented in which two non-ionic surfactants (abbreviated as A & B) known to act as emulsifier have been studied to get a better flotation performance for a preparation plant with varying feed characteristics. Laboratory flotation tests were conducted with both the surfactants using three feed samples of the plant by varying the dosage at three different levels. The highest combustible matter recovery (more than 80%) was obtained for surfactant B at a dosage of 75 ppm (parts per million) for feed 1. But at the same dosage the recovery decreased by 21% and 10.2 % respectively for feed 2 and 3. On the other hand surfactant A showed a consistent result for all the three feed samples giving the highest value at a dosage of 50 ppm followed by a decrease beyond this point. The tests were complemented by contact angle measurements that demonstrated the same trend. In addition to this the reproducibility of data for Surfactant A was checked and found that the standard deviations for both separation efficiency and combustible matter recovery were within the permissible range (less than 5%). Finally an in-plant process optimization study to evaluate the performance and applicability of surfactant A at industrial level was done and has been discussed.

Jan 1, 2016

By Harry Perry

By 1980, the free world's need for economic sources of energy is expected to double. As a result, there will be a tremendous potential for all energy sources working together to supply the demand. For coal to continue its dominant role as a low-cost energy source, means must be found for it to meet the challenge of nuclear power and to overcome obstacles placed on its use by air and water pollution regulations. As the more limited reserves of gas and oil diminish, economic ways are also required for converting coal to synthetic liquid and gaseous fuels, and to chemicals, thus resulting in optimum utility of the most abundant low-cost fuel resource. The means for accomplishing these ends can only come about by a vigorous research and development program. Successful efforts by industry and government working together, both in America and abroad, will assure the continued use of coal to meet the world's energy demands. This paper discusses the emerging patterns of energy sources throughout the world and the role that research and development on coal will play in supplying future energy requirements.

Jan 1, 1967

By J. S. Moretzsohn, D. F. Graham

"Airborne Synthetic Aperture Radar (SAR)was acquired over the Carajás Mineral Province, within the rainforests of the Amazon, which hosts the world’s largest Fe-ore deposit(Santos, 1986). Significant chemical weathering exists in this humid environment. PrevalentAu mineralization is thought to be generally associated with deformation zones in Archean schists.Radar data have proven to be very useful as an aid to geological mapping in the tropical rainforests of the Amazon Basin in Brazil. In these densely vegetated areas, a sense of regional structural trends is obtained as a con-sequence of the sensor/terrain geometry. The top forest canopy is the main terrain reflector of X-band radar energy, and consequently is the main terrain surface feature expressed in processed radar imagery. Radar is important for extending t,he continuity of mapped structural lineaments. Differential weathering is related to variations in radar image texture which is used to infer gross lithologic variations and relative age relationships of major rock units. Specifically, quartzites and banded iron formation are highlighted in the radar imagery due to their unique tonal and textural appearance, in contrast to schists, gneisses and metavolcanic rocks. As tropical areas are typically enveloped in cloud or mist, radar data are invaluable in providing information for logistical planning of field mapping activities."

Jan 1, 1997

By S. Shairp

The first commercial application of the Dynatec two-stage zinc pressure leach process commenced operation at the metallurgical complex of Hudson Bay Mining and Smelting Co., Limited in Flin Flon, Manitoba in 1993. A key feature of the successful leaching operation is the presence of iron in solution, which facilitates oxygen transfer in the autoclaves and enables rapid oxidation of zinc sulphide minerals. At the same time, the solution from which zinc is recovered must be essentially iron free. Precipitation of iron from the solution starts in the autoclaves and is completed in subsequent atmospheric purification steps. Conveniently, these iron precipitation steps also remove nuisance elements such as arsenic and fluoride from the solution, while producing solids with good liquid-solid separation characteristics. This paper provides an overview of the current operations in Flin Flon, with particular reference to the behaviour and deportment of iron throughout the zinc plant.

Jan 1, 2006

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By A R. Bullis

Metal Mines Limited (Bancroft Division) was incorporated m 1964 to take over the assets of Faraday Uranium Mines Ltd., including their uranium deposit near Bancroft. Ontario. This paper outlines the geology of the Bancroft area, and. then go on to describe the principle rock types m the mine workings, especially the pegmatite, which is the host rock for the uranium mineralization. The structure and mineralogy of the orebodies are thoroughly covered, and, after a summary of the production and ore re-serve figures, the paper concludes with suggestions for further exploration work. Location and History M ETAL Mines Limited, Bancroft Division, is located in Faraday township, Hastings county, Ontario. The main production shaft and concentrator are about: Y2 mile north of Highway 28 and about 5 miles west of the village of Bancroft (Figure 1). The presence of radioactive minerals in the Ban-croft-Wilberforce area has been known since the early 1920's. Uraninite was found at the Richardson deposit near Wilberforce in 1922, and some attempts were made to produce radium from the deposits of the area between 1929 and 1931.

Jan 1, 1965

By P. H. Jennings

Commercial tellurium commonly contains heavy basemetal impurities such as lead, copper, iron, etc., as well as selenium and oxygen. The base metals may be removed by vacuum distillation or by zone melting. Vacuum distillation is a convenient method for treating moderate quantities (~ 100 kg.) for the production of a material having a total content of heavy metals in the 10-30 ppm range. By zone melting, it is possible to lower all the heavy metal impurities tm below the limits of spectrographie detection. Neither vacuum distillation nor zone melting is effective for the removal of selenium, but treatment of molten tellurium with hydrogen converts selenium to hydrogen selenide. This procedure is too s low to be considered except as an adjunct to zone melting. In the course of air-melting, many of the more easily oxidized impurities form a dross and may thus be readily removed. Substantial refinement with respect to iron, tin, chromium, aluminum, sodium, silicon, magnesium, calcium and manganese can be achieved in this way. Although tellurium can be electrodeposited from either acid or alkaline solutions of the dioxide, various factors militate against successful electro-refining, amongst which may be mentioned the brittleness of cast tellurium anodes and the tendency for the metal to be deposited in dendritic form, even at low current densities.

Feb 1, 1966

By P. H. Jennings, J. C. T. Farge

Commercial tellurium commonly contains heavy base-metal impurities such as lead, copper, iron, etc., as well as selenium and oxygen. The base metals may be removed by vacuum distillation or by zone melting. Vacuum distillation is a convenient method for treating moderate quantities ( 100 kg.) for the production of a material having a total content of heavy metals in the 10-30 ppm range. By zone melting, it is possible to lower all the heavy metal impurities tm below the limits of spectrographie detection. Neither vacuum distillation nor zone melting is effective for the removal of selenium, but treatment of molten tellurium with hydrogen converts selenium to hydrogen selenide. This procedure is too slow to be considered except as an adjunct to zone melting. In the course of air-melting, many of the more easily oxidized impurities form a dross and may thus be readily removed. Substantial refinement with respect to iron, tin, chromium, aluminum, sodium, silicon, magnesium, calcium and manganese can be achieved in this way. Although tellurium can be electrodeposited from either acid or alkaline solutions of the dioxide, various factors militate against successful electro-refining, amongst which may be mentioned the brittleness of cast tellurium anodes and the tendency for the metal to be deposited in dendritic form, even at low current densities.

Jan 1, 1966

By R. H. Beaton

"About 1905, a plant was constructed at C1ayburn, in the Lower Fraser valley, 4'5 miles east of Vancouver, to process shales from Sumas mountain into heavy clay products. In time, mining operations were found to be more favourable on the opposite side of the mountain, and by 1913 a plant, which soon became the centre of activities, was completed at Kilgard. Destroyed by fire in 1949, the plant was rebuilt on modern lines, and a second plant was established at Abbotsford, six miles to the west. The Company, from its beginning, has grown with development of the Province. In recent years, operations have kept abreast of latest developments, particularly in materials handling. Latest innovation has been the complete conversion of fuel from Bunker C oil to natural gas. In 1957 the Company became associated with Harbison Walker Refractories, Limited, a leader in its field in the United States, and its title was changed from Clayburn Company, Limited, to Clayburn-Harbison, Limited. Currently, the Kilgard plant produces sewer pipe, agricultural tile, and flue liner; the Abbotsford plant, refractories and facebrick. Improvement of products and development of new ones are tasks of a recently-completed testing and research laboratory.Almost all ware produced is marketed in Western Canada or Washing-ton State. The Vancouver area absorbs the bulk of structural clay products."

Jan 1, 1959

By G Anders

The mucking out of sub-level headings by slusher and by Autoloader is described, and the performance and costs of both methods are compared. The introduction of the Autoloader is taken as an example to illustrate the meth-od used at the mine for evaluating the suitability of new equipment. The consecutive steps in the process are covered in detail -from the preliminary cost analysis and the preliminary estimate of savings and advantages, and the review of these data after a field investigation, through the elimination of dubious factors, and detailed time and performance studies at the property, to the final assessment of the new equipment and an evaluation of the initial forecast. The Autoloader in Operation. 1198 Introduction AT Mattagami Lake Mines Ltd., the mine workings are laid out basically on a pattern of 60-ft.-wide stapes alternating with 60-ft.-wide pillars, with stope lengths varying from 80 to 200 ft. and stope tonnages generally between 80,000 and 200,000 tons. Stapes are drilled off from sub-levels at 60-ft. intervals, with the

Jan 1, 1965

By J. Budac, E. Krause, C. L. Stewart, D. Wrana, S. W. Laundry

"As part of an over-all arsenic management strategy, Inco has developed a novel process that converts a by-product high moisture copper/arsenic sulphide precipitate into a crystalline copper arsenate suitable for the manufacture of wood preservation chemicals.The copper/arsenic sulphide precipitate is atmospherically leached with oxygen and sulphuric acid, producing a crude (blue) copper arsenate precipitate, elemental sulphur, and a copper and nickel containing solution. The blue copper arsenate is dissolved with sulphuric acid, the molar Cu/As ratio is raised to 2, and a crystalline copper arsenate (olivenite) is precipitated by the addition of sodium carbonate. Dissolved copper is recovered using metallic nickel (or matte) and elemental sulphur, to produce a low-moisture (low-arsenic) precipitate suitable for standard nickel-copper processing.The process was successfully piloted at Inco's Manitoba Division between September 1990 and June 1991. The copper arsenate product typically analyzed 43% Cu and 25% As, and the moisture content was about 10%."

Jan 1, 1995

By C. E. Rodgers

WHEN the writer was engaged early last year by Canadian Comstock and its subsidiary, the Metropolitan Electric Company, to act as Consulting Mining Engineer in connection with the layout and equipment of the new ore-dressing laboratories at Laval University, Quebec, the metallurgical laboratory section of the School of Mines building was completely erected, including plastered walls, partitions, etc., and finished concrete floors. At that time, however, no equipment had been ordered, except three Dominion ball-mills and two Bell screening machines. ADVANCED OR CONTINUOUS LABORATORIES The continuous laboratory section of the Department occupies the basement and three floors of the building, with an approximate floor area of 9,000 square feet. Because of limitations imposed by the design of the building (height and arrangement of rooms, strength and design of floors, etc.), modifications of layout from what otherwise seemed most desirable were, of necessity, made. These included: (a) Omission of automatic sampling of the dry ore. (b) Complete elimination of inclined belt-conveyors through floors. (c) Exclusion of bucket elevators for either dry or wet ore transfer. (d) As a substitute for grill-covered drains and floor sumps, drainage from sections or from individual pieces of equipment was piped to a disposal system in the basement. (e) Substitution in several instances of fabricated steel in place of the usual concrete foundations for machinery. (f) Reducing floor cutting and area of such opening to a minimum. Ore storage and chute capacity above the basement level was also minimized to reduce total weight.

Jan 1, 1941

By Terry A. Lee

The grade of mineral resource estimates underpin all major economic considerations of mining prospects. While there are reporting requirements to satisfy when stating a mineral resource estimate, an examination of NI 43-101 style reports suggests that authors believe that there are a number of ways of addressing these requirements. As a reader of these reports, some processes are helpful and others are not so in getting a real appreciation of how realistic is the mineral resource estimate. Critical to the quality of the mineral resource estimate is how realistic is the economic mineral concentration component. In many cases, this parameter is called grade. The industry experiences increased difficulty in achieving realistic grade estimates as the sample grade variability increases. The level of transparency in a mineral resource estimate is very much a function of the competence of the author. An objective presentation of the critical data, such as grade sampling variability can assist a reader in determining if the geology of the mineral concentration is adequately understood and how realistic is mineral resource grade estimate. This paper has considered 75 NI 43-101 style reports released in the past 2 years. The review demonstrates features that were helpful in determining how realistic the mineral resource grade estimate is. If there is insufficient transparency in a report, there is a high probability that the mineral resource grade estimate will not be realistic.

Apr 1, 2005

By A. C. Elliott, A. J. Lafreniere

THE Hamilton Works of The Steel Company of Canada is a fully integrated steel plant with an annual capacity of three million tons. Located on the south shore of -Hamilton bay, it is in the centre of Hamilton's industrial belt. The heavy concentration of industrial activities found in this area, accompanied metallurgical well-known sources of pollution which are normal to urban areas is creating a pollution problem which concerns both industry and the general public. The Steel Company of Canada has recognized this problem and, accordingly, has adopted the policy of integrating suitable pollution control devices into its new installations. Much effort is also being expended to control the emissions of air contaminants from the existing equipment. At the Hamilton Works, there are two main sources of metallurgical dust emissions to the atmosphere -the Open Hearth furnaces and the Sinter Plant. Of these two, the Open Hearth furnaces are, undoubtedly, the largest single source of

Jan 1, 1962

By W. C. Whittaker

COMPLETED in November, 1943, at a cost of over $1,500,000, Elk River colliery of the Crow's Nest Pass Coal Company, Limited, has been laid out and equipped for an ultimate annual production of 1,000,000 tons and replaces the recently closed Coal Creek plant, which has been operated by the Company for the past forty-five years. The project has involved the opening of mines in three seams, the construction of a complete set of colliery buildings, including a modern preparation plant of 360 tons per hour capacity, and the laying out of the necessary yard tracks and spur connecting the new development with the Company-owned Morrissey, Fernie and Michel railway, which, in turn, connects with the Canadian Pacific railway at Fernie. The colliery is three and a half miles east of Fernie, B.C., near the southern end of the Crow's Nest coal field, which contains the largest and most important body of coal in the Province of British Columbia. The coal-bearing horizon is the Kootenay formation, present in the form of a syncline covering an area of 230 square miles. Most of the coal seams occur in the lower 2,000 feet of the formation, the covering beds being largely coarse sandstones and conglomerates of great thickness, the presence of which accounts largely for the preservation of the coal measures. James McEvoy, in the report of the Geological Survey of Canada for the year 1900, states that the basin appears to contain a fairly constant coal content of nearly 172 feet in 23 seams of a thickness of one foot or over. Coal has been mined in the Fernie district since 1897 and the first shipments were made from Coal Creek colliery in the following year, over the then newly constructed British Columbia Southern railway. Since that time, a total of over 16,000,000 tons of coal has been produced, an average of 350,000 tons per year. The7ears of peak production were 1910, 1912, and 1913, with an all-time high of 924,000 tons in 1913. The lowest output in the history of Coal Creek was that for the year 1933, when only 60,340 tons were produced, the colliery being closed for some months. Present production from Elk River colliery averages 1,150 tons per day, the output being considerably less than it could be were sufficient man-power available.

Jan 1, 1944

By W. H. Hannay

Introduction The subject matter of this paper will be treated under two heads: (1) experimental work and the development of the purification system, and (2) the operation of the commercial plant. During 1927-28, a two-ton slag-retreating plant was in operation at the smelter for experimental purposes. Details of this operation and of the commercial plant are presented in a paper by G. E. Murray, read before the Annual General Meeting of the Institute in April, 1933 (1). A point which has considerable bearing on the subject of the present paper, and which was not emphasized by Mr. Murray, is the concentration of volatile impurities in the zinc oxide fume produced. The result of the operation of the slag fuming furnace is largely to confine in a closed circuit all the minor constituents of the Sullivan concentrates, both lead and zinc. They pass into the feed of the zinc fuming furnace, with the result that all impurities which volatilize-such as arsenic, antimony, tin, fluorine, etc.-report in the zinc oxide product. The accompanying condensed flow-sheet (Figure 1) will illustrate this. The only outlet for impurities which is not shown is the small tonnage which passes the Cottrell plants. The flow-sheet would indicate the possibility of building up a prohibitive concentration of cathodic impurities in the oxide leaching plant feed. However, after three years' continuous operation this has not occurred. Should this condition arise at some future date, discard of some tonnage of blast furnace slag is indicated. In Mr. Murray's paper, the much greater flexibility of blast furnace operation, due to the slag fuming furnace, is stressed, particularly as to the lead content of the slag. The requirements of our lead refinery call for a bullion containing about 0.70 percent antimony.

Jan 1, 1934

By E. P. Williams

"Prince Edward Island, Canada's smallest Maritime Province, is located in the southwestern part of the Gulf of St. Lawrence. The Province is more or less centrally located in the Maritimes Basin, a large intermontane basin within the Appalachian orogenic belt. The Maritimes Basin is subdivided into sub-basins and uplifts which exhibit two dominant structural trends: east and northeast. The Basin is known to be petroliferous because of the seeps, shows, oil shales and albertite found in southern New Brunswick and northern Nova Scotia and the gas and oil produced from the Stony Creek field near Moncton, New Brunswick.Permian beds are exposed on the Island, mostly along sea-cliffs. A maximum thickness of about 5,000 feet of red beds -shales, sandstones and conglomerates -make up the sequence. Over most of the Island, the Permian section is much thinner. Four key wells (Mississippian tests) and several shallower tests have been drilled. The Pennsylvanian-Mississippian section thickens rapidly off the Port Hill Uplift at the northwest, where it is less than 4,600 feet thick, and continues to thicken to about 20,000 feet in the Cumberland Basin at the southeast. Geological and geophysical data combine to give us the structural picture of the deeper beds.Prospective reservoir rocks are primarily in the Missis-sippian Horton and Windsor groups. Prospects are:-1. on or over structural highs in the basement; 2. on anticlines or fault highs; 3. over or peripheral to salt domes or salt-core anticlines; 4. at truncation pinchouts of Mississippian prospective beds; 5. in basal sandstone or granite wash on the pre-Carboni-ferous basement; and 6. in facies traps at changes from sandstone to shale or porous to tight carbonate rocks."

Jan 1, 1967

By F. Sorenson, P. A. Castellarini, F. Garbarino, M. N. Garcia

"Recently, significant efforts to improve productivity from the tight intervals of the Mulichinco Formation within the Sierra Chata Field in the Neuquén Basin have been ongoing. Because conventional high quality reservoirs were being developed in this field, a proper reservoir understanding and completion approach was applied. After developing these high permeability reservoirs, the operator began evaluating the tight intervals and new areas within the field, but a completely different approach was necessary to achieve motivating production improvement.An extensive study to help enhance reservoir understanding and identify key factors controlling productivity of these tight intervals (which tend to be in the range of 5 µD) has been ongoing. Some of the issues discussed in this study are 1) petrophysical review, 2) rock properties calibration, 3) geomechanics understanding, 4) faulting and micro faulting/lineaments description, 5) stimulation and completions review and, 6) understanding key production drivers.As in many other tight reservoir projects, a considerable area of the reservoir must be effectively stimulated during the hydraulic fracturing process to achieve economic productivity. Two critical issues hinder these objectives. First, the low permeability in addition to a pore pressure close to or even lower than hydrostatic are critical characteristics when attempting to flow back the well and clean up fractures. Second, very high horizontal stress anisotropy resulting from a strike slip stress regime promotes the generation of simple planar bi-wing fractures. It is well-known that this fracture geometry will contact much less reservoir area compared to more complex fractures, as the operator would normally intend to create at very low permeability reservoirs.This paper discusses these issues and how they were addressed. A pilot drilling and completion program was initiated during 2012 to validate this study. Key factors include well location relative to formation unconformities, their orientation relative to the far field principal stresses, hydraulic fractures generated, and overall completion design."

Jan 1, 2015

By B. Voyzelle

The deterioration of highway and bridge infrastructure has received considerable attention in recent years because of the billions of dollars needed for repair and rehabilitation. A major factor contributing to this problem is the corrosion of steel reinforcement. Reinforcing steels with good corrosion resistance and relatively low price are therefore essential for maintenance, cost reduction and service-life extension of the steel-reinforced structures. This article describes the development of low-alloying steels that offers good corrosion resistance with reasonably low cost. Topics include steel microstructures, mechanical properties, corrosion performance, industrial applications and economic aspects.

Jan 1, 2005

By J. -P. Lempainen, K. Haavanlammi, K. Valkama

The Outotec nickel matte chloride leaching process is especially suitable for small capacity standalone nickel refineries. The matte is leached with hydrochloric acid and oxygen in multiple steps in atmospheric OKTOP® reactors. Oxygen feed prevents reductive conditions and hydrogen formation in the leaching process. A sufficiently high acid concentration keeps the iron dissolved in the solution. The iron is removed after leaching by precipitation and the pregnant leach solution continues to metals recovery. The metals recovery from the chloride solution is done by solvent extractions, where ammonia is used for pH control. Copper and nickel are stripped from the organic phases into sulphate solutions. Metals can be recovered from the purified solution by conventional electrowinning. Other alternatives are precipitation or hydrogen reduction processes. The ammonium chloride in the solvent extraction raffinate is regenerated into ammonia. The calcium chloride solution from ammonia regeneration is routed to acid regeneration where sulphuric acid is added and ultra-pure gypsum is precipitated. The hydrochloric acid solution from this step is recycled back to leaching. The process yields good overall metal recoveries and expensive

Jan 1, 2014