Search Documents

By M. J. Gole, R. E. T. Hill, S. J. Barnes

"The Agnew (also known as the Perseverance) nickel deposit and its northern extension, the Rocky's Reward deposit, form one of the world's largest accumulations of nickel sulphides hosted by komatiites. Agnew was previously classified as an ""intrusive dunite-associated"" deposit . It has now been shown that the sulphides are hosted by komatiite flows which underlie an adcumulate-textured dunite body that crystallized in a large lava channel.The rocks of the mine area have been subjected to a metamorphic temperature of550°C and pressure of up to 3 kb. The komatiites have mostly been reconstituted to olivine-amphibole chlorite assemblages. There is a zoned sequence of enstatite-, anthophylite-, talc- and antigorite-bearing assemblages inwards from the western margin of the ultramatic reflecting variations in the CO/HP ratio of metamorphic fluids.Facing directions are determined from variations in the proportions of metamorphic minerals and in rock compositions which reflect asymmetric layering in the flows . Olivine-sulphides matrix ore is hosted in a single 50 m thick, east-facing flow that is overlain by flows containing massive sulphides. Much of the massive sulphide has been physically remobilized into fold noses, faults and shear zones. Chemical diffusion of ore components has upgraded a sulphide-rich metasedimentary unit where it is in structural contact with massive ore.To the north, the mineralized flow sequence is separated from a stratigraphically higher komatiite sequence, the Perseverance ultramafic complex, by approximately 150 m of felsic meta volcanic and meta sedimentary rocks. Southward, the Perseverance ultramafic grades laterally into an olivine adcumulate body and its lower contact cuts progressively down stratigraphy until it lies directly on top of olivine-sulphide ore of the mineralized flow sequence. This discordant contact is interpreted as the base of a thermal erosion channel formed by a voluminous komatiite lava flow. This contact greatly influenced later deformation of the mineralized flow sequence."

Jan 1, 1989

By John Kostuik

AT the Sladen-Malartic mine, a number of orebodies have been mined, some by shrinkage and others by open sub-level scopes, from which the ore is handled either through a grizzly system or by mechanical loaders. This paper deals with the comparative costs and relative merits of the two handling arrangements. The facts brought out in this comparison have a bearing on the selection of a proper handling method. The mine is in Fourniere township, northwestern Quebec, about forty miles east of the town of Rouyn. It is served by the Rouyn-Senneterre branch of the Canadian National railways. Two vertical three-compartment shafts give access to the present workings. No. 1 shaft, at which the plant is centralized, is the main hoisting shaft, with five levels to 950 feet. No. 2 shaft, 2,400 feet east of No. 1, is under development, with four levels to 725 feet. At the main shaft, the ore is hand-trammed in 1 1/2 tons cars from the scopes to the stations o:i each level and hoisted in cages to surface at a rope speed of 900 feet per minute. Air-operated tipples are used to dump the ore through grizzlies of 14-inch openings into a surface bin of 150 tons capacity. The ore hoisted at No. 2 shaft is trucked from the headframe bin to the mill. Milling commenced in January, 1938, ar a daily rate of 250 tons. Within two months this rate was increased to the unit's maximum capacity of 325 tons. A second unit to treat a further 325 tons daily was installed in April, 1939. The orebodies mined at No. 1 shaft are parts of a silicified zone at the contact between syenite porphyry and greywacke. The zone is ten co sixty feet wide, strikes easterly, and dips to the south at 55 to 85 degrees. The hanging-wall of the zone is marked, though not precisely, by a strong gouge fault. Locally, the boundary of silicification may be as much as twenty feet either above or below the fault, but for practical mining purposes the fault is the hanging-wall of the ore-zone. The footwall roughly parallels the fault, but as an assay wall it is usually irregular in detail. The ore is dense and hard, a siliceous replacement of both porphyry and greywacke, mineralized with fine disseminated pyrite.

Jan 1, 1941

By G. P. Contractor

Medium and low carbon steels, modified with uranium, were studied in order to evaluate the influence of uranium on forge ability, mechanical 11roperties, response to heat treatment and microstructure. Uranium contents ranged up to 0.70 per cent. The medium carbon steels are hot short if the uranium content exceeds about 0.35 per cent. More uranium can be tolerated in low carbon steels. The hot shortness is caused by the formation of intergranular phase UFe2. Critical transformation temperatures, Jominy hardenability, and resistance to tempering are not significantly affected by the 11resence of uranium. Similarly, uranium has little or no effect on the tensile properties of carbon steels. The addition of uranium has a favourable effect 11n the stress-rupture characteristics and some beneficial effect on fatigue properties. However, more results are required for verification. In the steels investigated, it seems that most of the uranium carbide combines to form complex inclusions of U (0, C, N) or (C, N), rich in oxygen or nitrogen or both.

Jan 1, 1963

By Roy O. Ifill, W. Charle Cooper, Alan H. Clark

"A detailed study of the compositional relationships of the Uand Th-bearing minerals in Elliot Lake uranium ores has been conducted, particularly with regard to uranothorite, which clearly plays a critical role in hydrometallurgical processing. Application of the rotating disc progressive-leaching technique to individual mineral grains and intergrowths of known compositions has defined for the first time the solubilization behaviour ofthe minerals in question.In descending order of leachability, regardless of leaching conditions, the phases are: uranothorite, uraninite, and monazite. Inclusions of secondary uranothorite enhance the dissolution kinetics of uraninite, which exhibits a complex dissolution mode. U-rich uranothorite dissolves more readily than Th-rich. Monazite is soluble in HJ)04 and HCI solutions only at temperatures exceeding 85°C. Consequently, it is deduced that the 15% to 20% of thorium not leached from the ore is lost both as monazite and as uranothorite inclusions locked in monazite which persists to the tailings. INTRODUCTIONThe importance of precise information on the mineralogy of ore and gangue constituents for the optimization of metal recovery in hydrometa Uurgical processing has been recognized for some years (e.g. Burkin, 1969), and numerous investigations integrating mineralogical studies and experimental leaching have been reported for ores of gold, nickel, copper and uranium (see summary by Henley, 1983). The complex mineralogy of uranium ores hosted by Precambrian pyritiferous, quartz-pebble, conglomerates has prompted particular attention in this regard (e.g. Liebenberg, 1956; Liebenberg and Taverner, 1958; Feather and Snegg, 1978). In the great majority of documented studies, however, petrographic examination has been followed by bulk leaching, an approach which, although providing valuable information, does not permit precise definition of the evolution of mineral dissolution processes. The authors contend that experimentation involving the step-by-step leaching and mineralogical study of ores is more likely to reveal the actual dissolution events which control the release of metals and, hence, may better define the optimal conditions for hydrometallurgical processing. Such studies (e.g. Hausen, 1983; Horlick et al., 1981) in addition lend themselves to the prediction of changes in the leaching behaviour of ores in which one or more mineralogical feature is subject to modification, a common characteristic of mineral deposits."

Jan 1, 1989

By Richard J. Kolada, Ian R. Muirhead

"This paper reports on a CANMET-funded examination of less conventional underground coal mining methods. These methods are documented and those that show the most promise for application to western Canadian conditions are discussed in detail.IntroductionIn recent years, mining considerations and economics have encouraged a transition from underground mining to surface mining. However, a change in market conditions or the development of superior underground mining methods may reverse this trend . Should this happen, the industry must be quick to respond and have information available on the latest developments of underground mining technology. In time, deposits of high-quality coal, which are easily accessible to surface mining, will be depleted and a change to underground mining methods will require consideration. The economic transition point between surface to underground will be a major determinant in maintaining a competitive edge. For these reasons, it is important to keep abreast of improvements in underground mining methods. To meet this objective, CANMET awarded a research contract to Monenco Consultants Limited, to investigate unconventional underground mining methods that show a potential for western Canadaoi. This paper presents the results of this investigation."

Jan 1, 1988

By Alan G. Galley

"Advances in our knowledge of the petrochemical attributes of deposit environments and of the character and extent of hydrothermal systems associated with certain deposit types has resulted in increased application of lithogeochemistry to exploration programs. Lithogeochemistry can be used to vector an exploration program toward an area of high potential through the use of a series of collapsing scales of analysis from a tectonic subprovince down to a particular stratigraphic segment. In the case of volcanogenic massive sulphide (VMS) deposits this involves the recognition ofsuitable volcanic domains, and the identification of subvolcanic intrusions and cogenetic felsic extrusive complexes. The recognition of chemical vectors within regional-scale alteration zones and associated chemical sedimentary rocks allows the geologist to identify the stratigraphic units with the most potential for hosting a base metal deposit.An integrated lithogeochemical program requires the judicious use of major, trace and rare-earth element and isotopic analysis. Standard discriminant plots may be employed to identify suitable tectonic and lithologic environments. Analysis of the chemical and mineralogical variations in broad-scale, semi-comfortable alteration zones provides a useful set of vectors to VMS mineralization. These may include contouring raw data, element ratios on XY plots, normalizing data against known rock values, or calculating mass changes in alteration zones."

Jan 1, 1995

By Robert B. Parsons

"A joint federal/provincial/industry subcommittee of the Intergovernmental Working Group on the Mineral Industry (IOWG) has published an informative and readable report on taxation matters concerning Canada's mining industry. The report, which was presented to the federal and provincial mines ministers in September 1986, identifies and discusses key tax issues relating to this industry. The report is mandatory reading for anybody with an interest in mineral exploration or production in Canada.IntroductionIn 1986, Canada's federal and provincial mines ministers were presented with an important report concerning the taxation of this country's mining industry. This document is important for a number of reasons, two of the reasons being: first, the report contains an objective analysis of the key mineral taxation issues of the day; and, second, the report is the product of a cooperative exercise involving representatives of various facets of the industry and government. The report should be regarded as compulsory reading for anybody who has an interest in fiscal matters affecting mineral exploration and production.The ""Report on Fiscal Proposals"" was prepared by a subcommittee of the Intergovernmental Working Group on the Mineral Industry (IOWO). IOWO is a group of senior federal, provincial, and territorial government officials concerned with the analysis of mineral policy issues in Canada."

Jan 1, 1986

By J. A. González-Anaya, F. Nava-Alonso, O. Alonso-González, F. Alvarado-Hernandez, A. Uribe-Salas, C. Jimenez-Velasco

"One of the most common hydrometallurgical methods for precious metal extraction is cyanidation. The effluents of this process may contain relatively high concentrations of copper, zinc and iron, which react with free cyanide to form complexes, adversely affecting the efficiency and the economy of the process.This preliminary work studies the use of the solvent extraction technique to remove copper, zinc and iron cyanide complexes from a synthetic solution similar to that of gold mill effluents, in order to allow the recycling of the solution back to the process. For the extraction of these anions (Cu(CN)2 -, Cu(CN)3 2-, Cu(CN)4 3-, Zn(CN)4 2- and Fe(CN)6 3-), trioctyl methyl ammonium chloride (Aliquat 336) was studied as extractant, using nonylphenol as modifier in the organic phase (iso-octane). The experimental results showed that for a synthetic solution containing 450 mg/L total cyanide, 160 mg/L copper, 50 mg/L zinc and 51 mg/L iron, it is possible to extract the 96% of copper, 91% of zinc and 75% of iron when using 0.011 mol/L of Aliquat 336 (organic/aqueous volume ratio (O/A) =1) in the pH range of 9-10."

Jan 1, 2014

By Paul Hughes

Purpose of Research ? What are the loading mechanics of paste against barricades? ? What is the capacity of the composite paste fill fences? ? Based on the loading mechanics of the paste, do the fill fences pose a risk of failure? Outline ? Glossary of Terms ? General Introduction ? Research Methodology ? Site Description ? Instrumentation Program ? Results ? Analysis ? Conclusions ? Recommendation for Future Work

May 1, 2008

By Reis. E., P. Pino Véliz

"Along the process of defining the fundamentals of a ferronickel project, several questions require proper answers from the very beginning such as the size and characteristics of the laterite deposit (oxide or silicate), the mineralogical variability, and the selection of the most valuable process route. In general, these elements will be defined along the progress of the exploration and feasibility studies, and definitive engineering. Also, from the very preliminary estimates, three questions are very common: what should be the plant capacity (annual tonnes of contained nickel), what will be the probable capital required (CAPEX), and what will be the estimated timeline (schedule) between the initial stage, say the feasibility study and the plant start-up and ramp-up to designed capacity. The accuracy of the capital cost estimates also progresses along the different stages of development from ±50% at the Preliminary Economic Assessment (PEA) stage down to ±5% for the Detailed Engineering and Construction stage. These accuracies of estimates have been, in some ways, accepted by the mining community and investors. The industry accepted benchmark for ferronickel projects in terms of CAPEX are then in the order of US$50,000 per tonne of nickel contained in the FeNi product. In this paper, the authors analyze in some details three ferronickel projects for lateritic ores that have selected the Rotary Kiln - Electric Furnace (RKEF) as the suitable technological route and have started production in the period 2006–2016. Some key aspects of the ferronickel projects are examined: 1) size and type of deposit; 2) flowsheet selection; 3) evolution of capital cost as a function of capacity from the feasibility stage to construction; 4) comparison between planned production scale and actual ramp up; 5) estimated capital expenditure (CAPEX) compared with actual figures; 6) nickel price evolution and timing of the approval for the project to proceed to construction and production start-up. The objective of this paper is to identify key elements that should be addressed in future projects and that are proposed as benchmark figures for similar projects."

Jan 1, 2017

By W. P. Campbell

THE investigation herein described had its beginning in the chemical laboratory of the Department of the Interior, Calgary. After the transfer of the natural resources to the Province of Alberta in 1930, the laboratory was closed and the investigation discontinued, but in 1933, with the permission of the Director of the Mines Branch, the work was again taken up and brought to completion. OBJECT OF THE INVESTIGATION The object of the investigation as originally planned may be stated as follows : (1) To determine the chemical composition of the limestone formation underlying Turner Valley gas field. (2) To identify 'beds' in the limestone, if such existed, with definitecharacteristics which would mark them from immediately overlying and underlying measures. (3) To relate information acquired on the composition of the limestone to the occurrence of oil and gas in the particular section examined. Definite information was lacking as to the exact chemical composition of the limestone and of its variations in composition at various depths. The formation was generally referred to in the field as the 'dolomitic' limestone, but the depth to which the dolomitized zone extended and the degree to which the limestone generally had become dolomitized were not known. Jn the drilling and logging of wells, the recognition of suitable 'markers' in the various formations is a matter of some importance. Markers are generally relatively small but widespread members of a formation, which have some characteristic property, of colour, composition, or form, by which they may be identified, and with them, consequently, the formation of which they form a part. In the formations above the limestone in Turner Valley, a number of well defined and easily recognized markers are known to geologists, drillers, and others interested in the field. Many of these markers Hand out in sharp contrast to adjoining measures and are therefore easily recognized; in others, the contrast is less sharp, with consequent difficulty in identification.

Jan 1, 1937

By G. Swan

"The selection of material comprising a backfill is, of economic necessity, site dependent. Nevertheless, given the existing range of typical components-coarse waste, alluvial sand, tailings a balanced or optimal choice is no straightforward matter. A new design approach toward deciding what constitutes an optimum combination of backfill material promises to be useful. In particular a 'binder ' number, based on the mean distance between aggregate particles, specific surface and cement content, is proposed. Using this number, related empirically to compressive strength, the expected mechanical performance of any cemented fill can be predicted.IntroductionOver the years a considerable volume of information has accumulated on mine backfill material design. The principal aggregate component has been deslimed mill tailings, though more recently admixtures of rock waste, sand and tailings are quite common. For these materials uniaxial compressive strength and percolation rate properties are known to be controlled by, among other things, aggregate grading. While empirical formulae exist for relating grading to percolation rates, considerable uncertainty exists concerning strength development."

Jan 1, 1985

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various complex ore deposits and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides and other phases for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay & Gorain, 2014; Chattopadhyay et al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2017

By Rodney Allen

Background: Development of the Project ?European GEODE collaboration 1999: considers possible projects, including a VMS project, to continue after GEODE ?GEODE-CODES-Canada collaboration 1999: Questionaire, database ?Workshop at CODES 2000: project theme and strategy selected ?GEORANGE (Sweden-EU) 2001 supports development of Global VMS Project: interest from 12 nations ?Skellefte VMS Project set up as Sweden?s component of Global VMS, 2002; other projects in Spain, Canada collaborate ?Low metal prices ---> little funding from mining industry 2001-2003, change in strategy ?IGCP/UNESCO support 2004: enlargement to over 20 nations

Apr 1, 2005

By D. Beneteau

Plotting sets of data collected over time using a frequency-magnitude distribution is common with both earthquake and mining seismology. A Time-Between-Events (TBE) analysis technique simply makes use of the inter-event times and b-values (slopes of the best fit lines on the frequency-magnitude charts) from the same set of data. Four distinct patterns in TBE versus Event Magnitude have been found which suggest whether there are constant seismic sources causing populations of data, or if the smaller and larger events, within the population represent varying seismic sources. Different rates of events, identified as TBE-rates in this study, may suggest whether the events are blast induced, or not. This study was done using actual seismic datasets from hardrock mines in Canada and Australia. This was to verify the applicability of the method to multiple mining environments and to determine the practicality and implications of this methodology to enhance the interpretation of seismic source mechanisms The results of the TBE technique and other proven techniques are combined into a Seismic Mechanism Assessment Worksheet. This is a tool that allows operators to compare trends within seismic datasets with assessments of in-situ rock conditions. The goal is to enhance the understanding of rockmass failure mechanisms.

Nov 1, 2011

By A. Ignatieff

This is the first in a series of Coal Technology Reviews being prepared in accordance with a recommendation voted by the Coal Division in session at the Jubilee Meeting, Vancouver, April, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review' of Coal Technology, for distribution among those concerned in the production and use of coal in Canada. This recommendation was subsequently endorsed both by the Council of the Institute and by the Dominion Coal Board. Further reviews (or digests) will appear at intervals in the Bulletin, or will be published and distributed by the Board which, meanwhile, has undertaken to distribute reprints of Mr. Ignatieff's review.-En. * * * The fields in coal mining technology which are considered to demand most attention and study at the present time are reviewed under the headings appearing below. Mechanization In the light of the growing shortage of skilled miners and the necessity of mitigating constantly increasing mining costs, interest continues to centre in mining methods and applications of mechanization chat will produce the maximum reduction of man power. The growth of strip or open-cut mining, also, is a consequence of this trend. Mechanization at the face attracts most attention and the trend is toward developing and adopting machines capable of cutting and loading the coal in one operation instead of having the separate operations of cutting, drilling, blasting, and loading. In Great Britain, where longwall mining is? the general practice, the A.B. Meco-Moore machine still receives much attention, and accounts describing its performance over reasonably long periods have appeared in the technical press.

Jan 1, 1948

By C. Stamberg, W. McGuire, R. C. Carlson, L. W. Vollmer

"The selection of materials and pre-cautionary measures for handling natural gas and condensate containing aqueous hydrogen sulphide are presented. Based on the results of a pilot production test and laboratory studies, together with several years . of operating experience, it was found that the behaviour of materials in sour gas environments can be predicted sufficiently accurately for engineering purposes.The selection of proper materials is essential for preventing sulphide-stress cracking. Where high strength materials are not required, low car-bon steel is used. Components requiring high tensile strength and hardness characteristics should be made from K-monel or properly heat-treated carbon-manganese-molybden-um and AISI 4140 steels. Welded connections are a potential source of sulphide-stress cracking. Consequently high quality welding and strict inspection are suggested as the most economical precautionary measures available.A maintenance program based,. where possible, on visual inspection of equipment and/or test spools located at strategic points should be used to follow weight loss and putting corrosion in sour gas environments. If severe weight loss or pitting corrosion is encountered, inhibitors have been found to be an effective deter-rent."

Jan 1, 1960

By H. Qi, J. L. Feng, D. J. Li

"In the present paper, the characteristics of the granite burst under loading/unloading conditions was studied by means of both laboratory experiment and finite-discrete element method (FDEM). After gaining the mechanical properties of the granite samples under uniaxial compression conditions, the parameters taken as input arguments in the FDEM modelling were then carefully calibrated so as to provide some basic data including Young’s modulus, Poisson’s ratio, uniaxial strength, Lame constants, cohesive strength, and frictional angle for further being used in simulating granite bursts. All the simulating results by the FDEM were basically in agreement with that obtained from the uniaxial compression test and triaxial granite bursts in laboratory, respectively. This study shows that that such computational mechanics of discontinua can be employed to gain powerful insight into the failure mechanism of granite burst, which could also be a useful tool to clarify the collapse mechanism of rock structures in rock engineering design and rock test scheme optimisation. INTRODUCTIONBased on discontinuum state a priori, discontinuous modeling techniques that are commonly referred to as discrete element methods (DEM) treat the material directly as an assembly of separate blocks or particles, which was originally proposed by Cundall (1971) and Cundall and Strack (1979) from the viewpoint of analogous molecular dynamics simulation to better account for and understand the interaction between the blocks. The distinct feature of these formulations is that a constantly changing problem of geometry and contact conditions can be addressed by solving the equations of motion using an explicit time marching scheme (most often in a ‘leap-frog’ format), while updating contact force histories as a consequence of contacts between different discrete elements and/or resulting from contacts with model boundaries (Bicanic 1998). The most notable implementations of DEMs are arguably represented by the universal distinct element code (UDEC) (Itasca Consulting Group Inc., 2013) and the particle flow code (PFC) (Itasca Consulting Group Inc., 2012). Another formulation is the discrete crack framework that is based upon some criteria for an advancement of crack front, which is coupled with extensive local and global re-meshing while simulating by numerical methods such as finite element technique, commonly using fracture theories. Certainly, it is relatively easy to trace the propagation of single crack front governed by some principles of energy release rates (Ingraffea 1997) but tracing of multiple cracks leads to topological and algorithmic complexities. Otherwise, there is no consideration of interacting cracks in these formulations of finite element or enhanced finite element techniques (e.g., in XFEM and ABAQUS)."

Jan 1, 2015

By B. Konda, R. Lauer, D. Camilucci, D. Gladwin

"Income based taxes are significant cost elements to be considered in evaluating investment in new mine development. This paper presents the results of comparative analysis of effective income-based tax rates for mining in the Northwest Territories (NWT), selected Canadian provinces and international jurisdictions. The study was done as background to a review of royalty regulations for the NWT. ObjectiveThis paper presents results of comparative analysis of effective mining royalty1 rates, and combined effective mining royalty and income tax rates on selected mine models for the Northwest Territories (NWT), with those for several other jurisdictions in Canada and abroad which compete with the NWT for mining investment.BackgroundThe February 27, 1995 federal budget directed the Department of Indian Affairs and Northern Development (DIAND) to proceed with a comprehensive review and amendments to northern natural resource management legislation in order “to increase revenues and ensure a fair return to the Crown.” DIAND is responsible for the administration of the Territorial Lands Act, and its regulations.The Territorial Lands Act gives the Governor-in-Council the authority to “… make regulations for the leasing of mining rights in, under or on territorial lands and the payment of royalties therefor,…”. In the NWT, the Canada Mining Regulations (CMR) provide for the disposition of mineral rights for most minerals, other than coal, petroleum and related hydrocarbons, in return for the payment of a royalty to the Crown.As part of this review of the NWT mining royalty regime, several computer mine models were developed and tax regimes in a number of jurisdictions were analyzed. Effective mining royalty rates, and the combined effective mining royalty and income tax rates were compared across the jurisdictions. The results presented in this paper are a part of the background work done in preparing a discussion paper on proposed changes to the NWT mining royalty that is expected to be released for public consultation in the very near future."

Jan 1, 1997

By R. K. Collings

"This paper summarizes research that was done at the Mines Branch, Ottawa, to evaluate samples of phosphogypsum for gypsum products manufacture. The samples were from phosphate fertilizer facilities at: Port Maitland, Ontario ; Valleyfield, Quebec; and Fort Saskatchewan and Redwater, Alberta. All samples were wet-screened, washed, filtered and calcined in a laboratory kettle at atmospheric pressure. Tests were also made at higher pressures in a small autoclave. The gypsum and resulting hemi-hydrate, being acidic, were treated before, during and after calcining with various bases. The hemi-hydrate products were checked for time of set, compressive strength and bond to gypsum wallboard paper. The results of this study indicate that phosphogypsum from each of the sources investigated has potential as a substitute for mined gypsum in gypsum products manufacture. Pilot-scale testing is recommended to confirm that the product would be satisfactory for the manufacture of plaster products on a commercial basis."

Jan 1, 1972