Search Documents

By Kavetsy A

In surface mining operations, the ease with which a muckpile may be dug is a dominant factor in mining efficiency. Within broad limits this is largely independent of the fragment size dis- tribution, since the equipment used to move the broken rock is generally larger than in underground mines. In such cases, muck- pile shape and voids ratio within a muckpile heavily influence mine productivity. In a particular operation, the muckpile shape after blasting should be tailored to the digging equipment being used. A front- end loader is best suited to a low, flat-lying, loose muckpile, because of its fairly good mobility and small break-out force with its bucket. In contrast, a rope shovel lacks mobility, generates a much larger break-out force with its bucket, and fills its bucket in a vertical filling motion. Therefore, it is ideally suited to well fragmented, steep faces. In situations where a dragline is used, the requirement for a suitable muckpile depends on the operat- ing scheme of the dragline. For a conventional highwall key method the preferred work- ing level of the dragline is the same as the highwall, so that the dragline may sit over its key. In this situation, the ideal muck- pile shape involves relatively little displacement of the fragmented rock, with a minimal "power trough" at the back of the blast. In throw blasting, on the other hand, it is desirable to cast as much of the spoil as possible across the pit. It is then necessary to optimize the blast design by maximizing the throw percentage under any necessary constraints (e.g. damage, vibration, flyrock, explosive cost).

Jan 1, 1988

The coastline is. an incomparable stretch of sea coast known as Ninety Mile Beach. Two gas pipelines and two oil pipelines carrying hydrocarbons from thb'Bass Strait fields to the markets of Australia cross this beach. They cannot be seen as they are laid in trenching stretch- ing many miles out to sea and the beach was restored to its natural state. Even where the dunes were disturbed, suitable grass was sown thus consolidating the sand and preventing erosion. Ninety Mile Beach is but one of the many key.wildlife and recreational areas that our operations must be concerned with. Others include Westernport and Corner Inlet, but the one discussed in this paper in particular is the platform area of the Bass Strait itself. Never was the old adage "an ounce of prevention is worth a pound of cure" more meaningful than in offshore oil production. All are well aware of some of the events of the past several years that resulted in large and costly oil spills. Far less is known, seen or publicised about the measures and developments that are undertaken to ensure that such events do not occur. We also have well developed plans for response in the event of an emergency situation, which can be initiated with great rapidity. Our responsibility is to ensure that with the best of engineering technology and operating procedures, spills do not occur.

Jan 1, 1971

The cost-effectiveness of blasts involving radiating blastholes is cur- rently restricted in the following ways. (a) Significant percentages of potential explosion energy are not being liberated; the collar sections of some charges are being dislocated and/or desensitised by the detonations of adjacent earlier-firing charges. (b) If the minimum charge spacing is too small, detonation of an early- firing charge can initiate an adjacent charge sympathetically, thereby eliminating the benefit of any intended inter-charge delay. (c) The overall distribution of energy is poor. Appreciably better fragmentation would be achieved if current drill- ing patterns were to be replaced by staggered fans/rings having a toe spac- ing : burden ratio of about 4 : 1. This wide-spaced pattern would enable a higher percentage of the potential energy to be released, would reduce the incidence of sympathetic detonation and would provide a superior overall distribution of this liberated energy. If improved fragmentation is not required, the proposed fan/ring design should allow a significant expansion of the blasthole pattern with consequential cost savings in drill- ing, explosives and initiation.

Jan 1, 1988

By Roderick W. F

The equipment and procedures used for green pellet production on a laboratory scale are given, together with a description of the straight grate pellet strand analogue which has been developed to examine the response of various ore types to heat hardening. The capabilities of the analogue are illustrated with data obtained from the balling and drying studies using a manganese ore. Differences in inter-batch pellet quality are discussed, and method of minimising the experimental error that can arise from these differences is Presented.

Jan 1, 1974

Permian ultramafic and associated rocks form a belt in East Nelson and contain widespread, but minor, chromite and copper mineralisation and some mining was carried out last century. Since mining ceased, about 1910, little mapping of the belt has been carried out although its origin has been debated vigorously. Recently it has been inferred to form part of a ophiolite sequence, which has been tectonically disrupted to form a melange, and several 'plate -tectonic' models have been proposed. Mapping in the central part of the belt has shown that mTlanges are to the east of the ophiolite sequence. Faulting is widespread so that in anyone section part of the sequence may be absent. Some of the faulting is difficult to recognise and probably took place during or soon after the sequence accumulated. Other faulting is clearly of Cenozoic age and includes major NNE striking faults, with large horizontal displacement, and approximately east-west striking faults with almost entirely vertical movement. The writer agrees that 'plate tectonics' could provide an acceptable explanation for the origin of the ophiolite sequence but the models so far proposed do not take into account the nature and field relationships of the rock units present. Copper Mineralisation is largely controlled by the younger faults, particularly those striking about north-east, and is largely confined to the western part of the ultramafic rocks particularly where slivers of the volcanics of the adjacent Lee River Group are enclosed. Mineralisation, along NNE striking shear zones, has recently been found in the volcanics some distance from the ultramafic rocks. The chromite mineralization is in the form of primary layering in the basal part of the ultramafic belt although in places it has been concentrated into lenses probably during serpentinisation.

Jan 1, 1977

The current boom conditions in the Gold Mining Industry, open cut low grade gold mines have become the initial cash flow source for most companies. To achieve the required cash flow the head grade needs to be maintained at the required level. The methods of grade control to achieve .the planned head grade have evolved various systems, one of which is the Ditch Witch Trencher. The application of this machine has revolutionised open cut grade control and Geology and this paper records the various methodologies developed in the Eastern Goldfields of Western Australia.

Jan 1, 1987

By Houchin MR, Jenkins DH

This paper examines the importance of processing to the properties and performance of high purity zirconia ceramics. Many of the principles discussed, however, apply to ceramic processing in general. For fabricated ceramic articles to display their wide range of high performance properties, they must be made fully dense. The precursor powder and postpowder processing requirements necessary to achieve full density in the fabricated body are discussed. Brittleness, the anathema of ceramics, can be overcome in zirconia by incorporation of toughening mechanisms. Transformation toughening and microcrack toughening and their origins in partially stabilized zirconia are reviewed.

Jan 1, 1989

By I R. F MacCulloch, K Jones

Pintail Systems, Inc, a Colorado USA based company has developed and commercially applied bioremediation processes for biological detoxification of cyanide compounds in mine waste. Site-specific microorganisms are isolated from spent ore, tailings or process solutions and augmented in the laboratory for cyanide oxidation, denitrification and metal biomineralisation. Biological processes typically treat complex contaminants (cyanide compounds, soluble metals and nitrates) in a fraction of the time of conventional remediation processes. Cyanide is used in microbial metabolic processes as a carbon or a nitrogen source. Biological detoxification processes applied at the end of mine life can end long-term liability and perpetual monitoring and containment. Case studies from commercial application and demonstration programs for the US Environmental Protection Agency will be presented in this paper.

Jan 1, 2004

By Jiricek F

Legislative change has reformed the licensing process in Victoria. The Mineral Resources Development Act 1990 and the two stage system of licensing with the authority to commence work is discussed. A key part is the requirements of planning consent, being either an Environmental Effects Statement or the issue of a Planning Permit prior to the issue of an authority to commence work for mineral extraction. Examples of recent experience is discussed.

Jan 1, 1997

IntroductionHistory of MineTopographyGeology of AreaGeneral DescriptionIgneous Rock TypesGranodioriteQuartz monzoniteApliteGranite porphyryMetasomatic ActionAlteration of monzonite/Alteration of apliteGeology of Ore BodyNature of OreZones of MetasomatismAssociated Fracture PlanesDistribution of Copper MineralisationNature of Copper VeinsQuartz-chalcopyrite veinsQuartz-calcite-chalcopyrite veinsEuhedral quartz veins/Non-euhedral quartz veinsStructures Accompanying Ore BodyApliteIntersecting lines of metasomatised monzoniteMetasomatised aplite

Jan 1, 1949

By P Hawkes

Within the mining industry computers have made their most significant impact with 3D design, visualisation and resource modelling/ optimisation. Recently, the application of computers to data gathering and accounting functions has also started to reap benefits. These two areas of application cover the beginning and end of the mining process. There has been limited use of computers on the middle section, the actual mining process. This is interesting when considering the relative proportion of overall mining costs that this section produces. There is a certain amount of irony in the lack of mining application software for developing accurate budgets compared to the systems/software then used to review performance against budget. Computers have been used extensively in the manufacturing industry to design, model and simulate the manufacturing process. This has not been extended to the mining process. But, we all strive to have an open pit that replicates a manufacturing plant û smooth, efficient, optimal production. If we could model mining operations with the confidence of plastic box makers we would reduce risk by an order of magnitude, improve planning and focus on value drivers. Cost û benefit analysis would be easy. The extrapolation of manufacturing to mining process models is difficult. The variables in the manufacturing process are fewer in number, have low volatility and are highly predictable. The time between a box falling on a conveyor belt and falling off is very consistent. Mining is quite the opposite. It has large numbers of variables, some of which are unpredictable and volatile. The time to fill an excavator bucket could vary by 30 per cent and the frequency distribution is unlikely to be a mathematically simple normal distribution. Further, each of these variables can be distorted by one-another û they are interrelated. The mining process is a disjointed flow of parcels whereas manufacturing is a controlled continuous feed. A loaded truck might join a ramp and follow a slow water cart up. This is the equivalent of a localised voltage drop on equipment in a manufacturing plant. The manufacturing plant is quite likely to rapidly recover to full capacity. Whereas the slow truck might throw the mining fleet cycle out of balance for hours û trucks queuing at the ROM bin and so on. A mining process simulation has been created that addresses these mining variable issues to produce a highly accurate model of the open pit mining process. The number of uses for such a model is growing rapidly as it is being utilised for a variety of projects within the industry. This paper discusses the need for and application of mining process models.

Jan 1, 2003

Valuers will often intuitively express the probability that property value will exceed a certain amount . . . 'I think the chances that the value will exceed $50 million are excellent. The chances that they will exceed $80 million are poor'. This paper shows how it is possible to combine the uncertainties of the value of several key items to provide an estimate of the probability of a certain overall value being achieved. The valuation of a large copper/gold deposit was naturally influenced by uncertainties in the base assumptions of costs and metal prices. Potential acquisition of the property through share purchase raised the issue of what was a reasonable intrinsic value for the shares. Market considerations could be used to appropriately adjust the intrinsic value. After a range of possible metal prices and operating costs were determined, estimates were made of their probable distributions. By combining these probabilities in a random selection, a range of property values was calculated. Each value had its respective probability of occurrence. This allowed a most likely value of shares to be calculated. This paper demonstrates how the valuer's intuition is complemented by numerical analysis.

Jan 1, 1994

By Ellicott C, Webb N

In November 1996 the NSW Minister for Mineral Resources, Hon Bob Martin MP, commissioned ACiL Economics and Policy Pty Ltd to conduct a wide ranging review of safety within the New South Wales mining industry.The review was a response to a disturbing number of fatalities which had occurred in the industry during the Minister's term of office together with a number of alarming near misses where serious failures in mining systems had occurred. Shortly after the review was commissioned, four mine workers died at Gretley Colliery near Newcastle. An inquiry is currently being conducted into the incident.

Jan 1, 1998

By Rienks, Wyborn D

The Ravenswood Batholith in the Charters Towers -Ravenswood area of north Queensland, was formed by three main episodes of granitoid emplacement between the Early Ordovician and the Early Permian. Granite to granodiorite plutons of the first phase of intrusions in the Early to Middle Ordovician, probably formed by partial melting of a thin continental crust as a result of the emplacement of mafic material derived from the mantle. Some of this mafic material subsequently intruded the Ordovician granitoids as gabbro to diorite complexes. The early granitoids were deformed and metamorphosed prior to emplacement of second phase granodiorite to tonalite plutons in the Late Silurian to Early Devonian. These later plutons have generally not been deformed or recrystallised. Geochemical and isotopic data suggest the Siluro-Devonian plutonism may have been generated by a partial melting of the tholeiitic material emplaced in the lower crust during the Ordovician. A third intrusive phase consists principally off Late Carboniferous to Early Permian gabbro-granite complexes, high level granite to granodiorite complexes, and rhyolitic plugs and diatremes near the batholith margin. Gold mineralisation in the batholith is associated with two major events: mesothermal vein formation in the Early Devonian and porphyry types in the Late Carboniferous to Early Permian.

Jan 1, 1990

By Maslov LA

We have considered the following characteristics of the crust and upper mantle of the Pacific Belt: seismic wave velocit> anomalies, mechanical stress and shear deformation rate fields, heat flow and the pattern of metallogenic provinces of the Belt. It has been noted that there exist certain regularities in distribution of the above mentioned geophysical characteristics and metallogenic zones within the Belt, displayed by prevalence of the lithophile elements in the Asia-Australian part of the Belt, and of the chalcophile ones within the American part.

Jan 1, 1995

By Baafi EY

Deposits of gold, silver and other precious metals often display a high variability of grade values, usually a very low average metal content and are frequently not easy to sample reliably. The characteristics, together with the volatility of precious metal prices, make evaluations of precious metal deposits extremely difficult to make. Geostatistical estimation techniques can be used to make grade estimates of precious metals and to assess the reliability of these estimates. Two case studies are presented.

Jan 1, 1987

This paper describes an ongoing study into the management systems developed by mining operations in Papua New Guinea to address particular public health issues in the workforce (primarily communicable and lifestyle diseases). The first stage of the study involves the analysis of the site health and safety management system documentation of three major mining operations in Papua New Guinea, producing a descriptive summary of each system. In the second stage of the study these summary descriptions are evaluated using a maturity model constructed through a detailed review of literature. Experience with the evaluation process is then used to refine the maturity model. The analysis performed in the study is used to develop a process for creating a maturity model for mine site health risk management based on a theoretical risk management framework, and refining it through empirical evaluations of the actual systems in place on site. Companies can use maturity models as a guide to organisational improvement, which in the context of the study will assist the operations in developing their systems for the management of health both in their workforce and in local communities.

Jan 1, 2007

By Denby B, Miles N. J

The underlying theory behind the construction of an on-line size analysis system is described together with an introduction to the Artificial Intelligent techniques that it is founded on. Previous systems based on more traditional technology such as edge detection and dilation algorithms have been restricted by the significant processing power they require, this has resulted in the production of systems with either reduced functionality or severe hardware requirements. A neural network approach offered a new perspective to the problem of size analysis; the ability of a network to learn and recognise subtle patterns in training data before on-line processing is initiated opened up the possibility for the production of a fully functioning practical system. The format of the training data had to be carefully analysed prior to its implementation in a neural network as the capability of a neural network solution depends as much upon a suitable data preparation as it does on the system architecture. To facilitate experimentation with various profile quantification techniques such as fourier and fractal analysis an Image Profile Analysis System was constructed (IPAS) in software on a personal computer. The IPAS system was produced with the aim of pre-processing image data to create data sets for experimenting with external neural network packages. The system allows the analysis of both real images obtained by image capture and simulated images created by an in-built in simulator. A measurement comparison scheme is also included together with a case study concerned with the frequency analysis of simulated images. The power of neural networks combined with the data compression provided by profiling removes the need for direct measurement of individual particles. This has obvious implications on the level of hardware necessary, and ultimately the expense of a stand alone system. The extrusive nature of data collection via an image analysis system will also permit simple installation of a shipped system; eliminating any requirement for interference with existing machinery.

Jan 1, 1995

Efforts to stabilize international markets in commodities have gradually intensified during the course of this century in keeping with the grow- ing complexity and interdependence of the world economy and the increasing involvement of government in economic activity. Successive Australian Governments have con- sistently supported the concept of commodity agreements and arrangements in an effort to lessen short term fluctuations in price and to moderate the boom/bust conditions which tend to charac- terize production and trade in many commodities. The objective is to stabilize price at a level which equates supply and demand over the life of the arrangement. Such action involves a degree of market inter- vention and government involvement in the inter- national trade in the commodity concerned; the acceptability and desire to foster such arrange- ments varies from country to country depending upon attitudes to market intervention and man- agement. However attitudes, even among those opposing commodity agreements, have under- gone a major reversal in this century. Before the first world war, such intervention as existed almost entirely involved the physical producers. There was almost no government involvement and at that level most regarded commodity agree- ments as neither desirable nor practical. However government regulation of such activities as pro- duction and marketing of food during World War I, coupled with post-war shortages, followed by overproduction and the crash in prices during the Great Depression, stimulated producer gov- ernment interest in commodity market regulation. Consumer governments took a little longer and with a few exceptions, it was not until the post World War II period, that the fear of shortages of basic commodities brought some consumer countries to accept the concept.

Jan 1, 1978

The southern portion of the Swan Coastal Plain, a geomor-: phological element formed since late'Tertiary times, contains commercially exploitable accumulations of ilmenite, zircon, rutile'and monazite associated with a series'of raised'shorelines. The:location'of the deposits is controlled by a locally outcropping*Archaen-granite/granulite complex and a sea':current pattern'determined'by'local geography and a prevailing wind direction.'-A progression from medium. to high titanium ilmenite is'evident parallelled by. progressive leucoxenisation as the age of the deposits increases. Variation's in trace element content accompany this process. Circulating groundwater has caused vertical mineralogical variations within-individual deposits and' by p'ecipitation of iron has formed layers of hardpan. The economic sig- nificance''of the Geographe--Bay deposits is'briefly discussed,

Jan 1, 1964