Search Documents

Estimation of operating costs in the nickel production industry requires a detailed analysis of material flows from mine to smelter to refinery. Despite the small number of nickel producers compared to other base metals, the existence of two very different ore types (sulphide and laterite) and a wide variety of mining and processing technologies make the identification of these flows of critical importance if an accurate global picture is to be obtained. Smelting and refining processes in nickel metallurgy have evolved with a high degree of adaptation to specific operating conditions in different locations. Overall costs are calculated by combining individual cost elements for each unit in production chains from mine to saleable metal product. The average cost of western world primary nickel production in 1995 was US$2.07/lb ($4560/tonne). Average operating costs remained virtually unchanged in the three years to 1995 after an 8.5 per cent fall in 1993, but a 3.9 per cent increase to $2.15/lb is expected for 1996. A major factor in this rise results from the lower prices of copper and cobalt this year, reducing the by-product credits available to major producers.

Jan 1, 1996

By P J. Hawke

Within the Mesa J pisolitic iron ore mine, clay is distributed unevenly throughout the deposit and often forms as pods and channels less than 10 m in width. The mine resource model, based on 50 m + 50 m spaced drilling, has been unable to accurately delineate the clay for scheduling and mining purposes. Therefore, alternative methods for mapping the clay-contaminated ore were sought. Predictive clay mapping will significantly reduce production costs at Mesa J through improved selective mining practices, more accurate scheduling, reduced wear on mining equipment and minimising the need for maintenance of haul roads and ramps. High lateral resolution electromagnetic (EM) surveying using a Geonics EM31 instrument can quickly and inexpensively delineate the extent and orientation of the clays. Preliminary results indicate that a block model based on the interpretation of the EM data can accurately predict the distribution, volume and tonnage of ore and waste material. While rip-line mapping, infill drilling, ground penetrating radar and gravity can delineate clay with various degrees of success, none were as efficient as EM31.

Jan 1, 2002

The mined-out Old Waite volcanogenic Cu-Zn deposit lies in the Noranda mining district of northwestern Quebec. The deposit has a distinctive pipe-like zone of alteration beneath the massive ore, extending into the stratigraphic footwall. The hydrothermal metasomatism within the alteration pipe produced a concentric zonation. with a peripheral quartz - sericite - chlorite mineral assemblage surrounding an axial core of magnesian chlorite - Phlogopite.

Jan 1, 1989

By C O. Gomez

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

By Weber D, Knox PR

The criteria developed for the Argyle Diamond Mine process plant control system are reviewed. The control system installed is described along with a discussion of the method of implementation adopted. The control system was extensively tested prior to instal- lation at site. This approach led to signi- ficant time savings during plant commissioning and facilitated rapid escalation of plant production. The control system has performed satisfactorily with a high level of operator acceptance and basically satisfies the criteria Developed.

Jan 1, 1986

By Yao S, Wang P, Zhang C

The Zhilingtou Au-Ag deposit is situated in the eastern part of the complexly deformed and metamorphosed South China Caledonian Fold Belt. It consists of seven orebodies that are almost exclusively hosted by biotite plagioclase gneiss of the Precambrian Chencai Group. They form an apparent en echelon pattern in both cross-section and level plan. Three different ore types, based on mineralization textures, have been recognized within the Zhilingtou lode. These are Au-Ag-rich quartz veins, Au and Ag-bearing silicified rocks and Au-Ag-containing altered rocks with quartz stockworks. The mineralization is principally composed of electrum, argentite, pyrite and minor sphalerite, galena as well as traces of hessite and chalcopyrite plus a gangue assemblage of quartz, rhodonite, sericite and chlorite. Fluid inclusions related to Au-Ag mineralization yield a wide range of homogenization temperatures from 110 to 447¦C, with two distinctive peak values at 250-300¦C and 350-400¦C respectively. S30Si values of quartz veins and silicification from the three stages of mineralization range from -0.1 to -0.4%o. The mineralization at Zhilingtou is interpreted as forming by recirculated meteoric water extracting ore-forming elements from metamorphic rocks due to Mesozoic volcano-magmatic activity.

Jan 1, 1995

The accuracy of an ore reserve is only as good as the geologist's understanding of the deposit. The methods that are applied to resource and reserve estimation reflect that understanding. At the Olympic Dam copper-uranium-gold deposit in South Australia, evolution in the understanding of the controls on mineralisation coupled with the changing demands of the project have led to changes in the approach to reserve estimation. The project has moved into a phase where detailed stope mining reserves are now required as distinct from global ore reserves. The complex nature of the mineralisation and the large amount of data demand that all available information be readily accessible in a flexible format. To enable the selective manipulation of geological and assay information and its characterisation, a relational database has been developed. For reserve calculations themselves, initial computations were based on a system derived from that used for the Kambalda nickel orebodies. The Olympic Dam system differed mainly in the use of statistical analyses in the estimation of grade instead of the previous polygonal area of influence weighting method, Three dimensional weighting techniques are now being used for local reserve estimates. Flexible facilities for raw data handling combined with grade estimation techniques which are commensurate with the mine geologist's understanding, produce detailed gridded and contoured ore zone models suitable for reserve calculations and stope designs.

Jan 1, 1987

By P Townsend, F Russell

Palabora Mining Company operates an integrated open pit mine, concentrator, smelter and refinery complex located in the Northern Province of South Africa. The Palabora open pit went into production in 1966, mining 30 000 t/d to produce some 62 000 tpa of copper. With continuous modification and improvement, a mining rate of 82 000 t/d, producing up to 135 000 tpa of refined copper, has been achieved. While these improvements have also enabled the mine life to be nearly doubled, the open pit will reach the end of its economic life by 2003. The Palabora orebody is vertical and the reserve extends to a depth of 1800 m over an area of 700 m by 200 m. Studies to assess the economics of mining the orebody by underground means began in the mid-1980s. These studies indicated that block caving is the lowest cost underground mining method that would generate a suitable return. In March 1996, a decision was made to develop a 30 000 t/d block cave mine that will extend the life of the Palabora Mining Company by a further 20 years. In terms of the relatively high rock strength and the resultant coarse fragmentation that is expected at the drawpoint, the Palabora cave can be considered rather unique when compared to other block cave operations. This paper describes the project in broad terms and details the mining method, particularly with respect to the cavability of the orebody and the design features to deal with the coarse fragmentation. The project commenced in July 1996 and final development of the undercut and drawbells is scheduled for completion in November 2003. This paper describes the status of the project and planning as of April 2000.

Jan 1, 2000

One of primary causes of poor blast performance is the improper relief of explosive energy. Under or over-confined blasts modify the explosiveÆs path of least resistance, which changes where and when the explosive energy is applied resulting in less than optimum blast performance. During the research for this paper the overbreak characteristics of five full-scale blasts were quantified using high speed cinematography and borehole cameras. The effectiveness of various overbreak control methods was also evaluated to guide design refinement. The results of this research along with general recommendations for reducing excessive damage are included with this paper.

Jan 1, 1999

By Marshall GA

Structural fatigue damage of haul truck frames is a costly problem associated with the operation of large mine haul trucks. A monitoring programme is described which has been instigated to measure stresses in the frames of haul trucks under actual mine operating conditions. The instrumentation used and methodology employed in the computer analysis of the results is briefly described. The results of the monitoring programmes are reviewed, and the effects of various factors affecting structural fatigue damage of three common types of rear dump truck are considered. Factors discussed include the effects of haul route features (for example shovel, dump and crusher areas); the effect of operations such as turning, braking, loading and dumping; the influence of payload; the effects of malfunctions in suspensions; and the influence of haul route surface quality. It is shown that with respect to payload, while structural fatigue damage is increased with payload, the structural damage per unit of payload does not change significantly for moderate increases in payload above the nominal value. Finally, on the basis of these results, recommendations are made for haul route design and operational practices which will increase the structural fatigue life of haul truck frames.

Jan 1, 1986

The firing of mass blasts at Isa Mine is a normal operating practice. Both electric and non-electric initiating systems are being used for this purpose. The advantages gained by large firings relate to the Planning, Scheduling, Services and Production functions of Isa Mine. More efficient us"e is made of manpower due to the concentrated charging effort and con- tinuity of the charging operation. In addition, the requirement for ring firing personnel to work at the edge of large stope voids is reduced. Better fragmentation results from the interaction of adjacent detonating rings of blastholes and in flight collisions. With mass blasts there is also less chance of large blocks of ore, created by faults or joints, falling into the stope and creating problems at the drawpoints. The formation of a large tonnage of broken ore facilitates production at scheduled rates from that stope source. The weight of explosive detonating during a mass blast can be considerable. Isa Mine has achieved satisfactory blasting results without excessive ground vibration levels and present knowledge indicates that pillar ground stab- ility has been maintained.

Jan 1, 1978

By Moore R

An intensive safety campaign at Mount Isa Mines Limited from 1956 to 1966 saw the lost time accident frequency rate fall to half its original level. A review of the safety programme was carried out in 1967 and in 1968 the Five Point Safety System was introduced. The seven years since its introduction have been years of significant achievement both in production and safety. Improving safety is a fundamental part of Mount Isa Mines Limited's policy and this system has been a major tool in implementing that policy. To be successful personnel need to be prepared and trained for its introduction and subsequently counselled on its use. A carefully prepared programme is required to phase in various aspects of the system and to make use of complementary steps. The system has been a success and it is anticipated that the continued drive to improve the use of principles of the system will further improve safety. It is hoped that this paper will be of value to those personnel concerned with industrial safety in Australia.

Jan 1, 1975

Tailings facilities tell a story to the public about how the mining industry manages its activities. They also create a risk that must be managed for the long term. All the knowledge and technology is available to safely design, build, operate and decommission tailings facilities.   Tailings at Waikato North Head Minesite are pumped as slurry, over long distances and against high static discharge heads to backfill the excavated area. WNH is, under the mining licence, obliged to reconcile the topography of mined areas to the closest possible resemblance of the original terrain. The active tailings areas are located near main operational facilities and detailed plans and procedures have been developed to ensure a safe and continuous operation.   The concentration plant is designed as two identical and independent plants. Each plant has its own tailings slurry pumping system.   This paper represents a general overview of the tailings disposal practice at WNH mine site. It discusses tailings delivery, construction and water management.

Jan 1, 2004

The Yilgarn Block of Western Australia presents (figure 1) a number of problems for conventional diamond exploration based on heavy indicator mineral sampling. These problems are due to the geology and unique geomorphological development of the Yilgarn Block.Essentially the Yilgarn Block is a pene- plain developed on a craton composed of Archaean intrusive granitoid rocks with meta- morphosed greenstone; which, apart from regional uplift, has not been tectonically disturbed since planation by glaciation in the Permian. Therefore since the early Plesozoic the Yilgarn Block has been subjected to terres- trial weathering conditions. Bettany et al., (1984) identify two phases of particular importance in the development of the present landforms: 1. Periods of lateritization during the Tertiary which result in the ~lassi~al laterite profile (figure 2). Duricrust indurated : Fe and Al oxides Mottled zone : Clay and Fe oxides Saprolite or pallid zone : leached clay grading into fresh rock. 2. Subsequent periods of aridity and semi- aridity during which laterite development was truncated and reworking of laterite Occurred.

Jan 1, 1988

The growth in the nickel market and the price increases predicted in 1970 have not mat-erialized. Several plants have been construct-ed, particularly to treat lateritic ores. A spectacular increase in cost of energy and the escalation of capital costs have led to severe economic difficulties on the part of many nickel producers. Several of the nickel prod-ucers joined together to form a Nickel Develop-ment Institute in 1984 with the prime objective of improving nickel markets. Most producers have taken exceptional action to cut overall costs as well as unit costs. Another organiz-ation made up of nickel producers, NiPERA, was established in 1980, to study and take action on problems of nickel in the environment and especially in the workplace.Ion exchange, and particularly continuous ion exchange, has been developed into a reli-able commercial unit operation in the last dec-ade. An example of how ion exchange combined with hydrogen reduction can be integrated into a Caron type reduction roast ammonium carbonate leach process for the recovery of nickel from laterites is discussed.

Jan 1, 1985

The first step in the mining and processing of nearly any mineral ore is comminution. Since the oil embargo of 1979, the mining companies have been striving to reduce energy consumption and costs. The first serious step was the introduction of in-pit crushing in the early 1980s. With in-pit crushing accepted as a standard design mode, the energy saving emphasis turned to comminution practices. A great deal of attention has been focused on blasting and grinding. The one step that has not been addressed is the primary crusher. This paper will address the opportunities for comminution improvement through optimisation of the primary crusher.

Jan 1, 2004

Pilot plant work has played a major role in the process development and design phase of the Iscor Heavy Minerals project. The pilot plant campaigns have been aimed at three process areas, namely primary beneficiation (wet gravity circuits), heavy mineral separation and ilmenite smelting. A process development structure was put in place, and the various pilot plants designed and built. A number of pilot campaigns were conducted during the project phase since 1995, and most of the key objectives were achieved. Various other valuable ælessonsÆ were learnt, and were incorporated in the full-scale plant designs, or used to change operating philosophies, equipment choices et cetera. The cost and durations of the pilot runs were significant, and an analysis indicated that the major risk and technology area of smelting has contributed more than 70 per cent of the total cost.

Jan 1, 2001

By Chavant G, Begis D, Gunther J

To study the ventilation of a mine (improve on the existing situation, examine extension projects) the calculation program used must take into account all the resistance values in the branches of the network. These resistance values are generally determined by measurements, which are accurate to a greater or lesser extent. In order to arrive by calculation at the flowrates measured :n the mine at a given moment, the resistance values have tto be adjusted experimentally. This manual operation is lengthy and delicate.

Jan 1, 1988

By Osborne V. J, Urbank W

An explosion occurred at Moura No. 4 underground coal mine in Queensland on 16 July 1986 and resulted in the loss of 12 lives. The official report of the accident concluded that the most likely source of ignition was the flame safety lamp. This paper describes an investigation of the behaviour of a flame safety lamp, similar to the one involved in the Moura explosion in atmospheres of methane, coal dust and air, carried out at the Queensland Department of Mines . Testing and Research Station. The behaviour of the lamp is described in conditions of varying methane and coal dust concentrations in air, and varying air velocity. Particular emphasis is given to the 'phenomenon of burning which occurs inside the gauze and which is capable of causing the ignition of an external explosive atmosphere.

Jan 1, 1988

By Napier-Munn TJ

The Whiten model of crushers is currently being refined and extended at the JKMRC, with particular reference to cone crushers. This paper describes the model as a predictor of crusher power draw, discusses the application of the model, and considers the relationship between power draw and crusher performance.

Jan 1, 1988