Search Documents

Tertiary laterite is extensively developed in the Darling Range area, but there is doubt that. the high relief areas along the Darling Scarp have been peneplaned. Three distinct laterite types are distinguished which are termed transported, introduced and residual laterites to avoid ambiguity. Transported laterites are recemented (primarily) lateritic materials and introduced laterites are chemical deposits of bog iron type. Residual laterites are formed in situ from the host material which can be either decomposed bedrock or detrital' clay, and the two varieties formed from these sources are termed residual A and residual B laterites. The genetic requirements for residual laterite formation are (1) host material, (2) porosity and permeability, (3) rainfall, (4) temperature, (5) relief and drainage, (6) vege- tation and (7) time. Previous theories on the origin of laterite appear to be inadequate and incompatible with field observations. Field investigations and drilling in the Darling Range area disclosed lenticular section and thickest laterite development on slopes and thin or oc- casionally no laterite development on crests. Lateritisation is considered a surface feature and the end product of the chemical weathering cycle. The relief and rain-water acting on a kaolinitic host material are con- sidered the major contributing factors in the

Jan 1, 1973

By Mitchell M. A

The steeply dipping Mammoth orebody is mined by Gunpowder Copper Limited using a sub- level uphole bench stoping method at a mining rate of 350 000 tonnes per year. of three per cent copper ore. Access to the mine, is provided by 1 in 9 decline which spirals in the footwall connect-, ing all the sublevels, thus maximising mobility and accessibility of trackless mining equipment Sublevels are driven in ore off cross- cuts from the decline every 15 metres vertic- ally. Sublevel drives are stripped out to widths up to 18 metres before cutoff slots are mined at each end. A two boom fan drilling jumbo is used to drill inclined rows of holes to the floor of the sublevel above. Two or three rows are fired at a time which allows broken ore and remnants from the level above to be mucked out by rubber tyred LHD equipment to the brow. Ore widths of up to 80 metres are en- countered at lower levels where ring drilling from longitudinal drill drives will break ore to a draw point system below. Development is carried out with three boom rubber tyred jumbos. All haulage from the mine is in 20 and 35 tonne rear dump trucks. All aspects of the mining operation are discussed including ventilation, pumping and drainage, services and future planning.

Jan 1, 1974

The link between exploration success and new ideas from research and development (R&D), although often assumed, is rarely well explained or well illustrated. One issue is understanding the role of innovative ideas in the exploration process, and another is determining the relative contributing factors to an exploration success. A useful measure of gold exploration success over an extended time period and geographic area is discovery rate (θ): Discovery rate θ = gold discovered/exploration expenditure (usefully expressed as tonnes of gold per $1 million). The total gold discovered is strongly leveraged to discovery rate, as any increase in θ typically has a positive effect on exploration expenditure. Hence, improving the discovery rate is a key driver for a sustainable mineral industry, especially for gold. There are very few ways to influence θ beyond innovative R&D ideas and breakthroughs, and well-motivated and trained staff. The Australian gold industry has experienced exceptional exploration success with 9956 tonnes of gold discovered from 1979 to 2003, inclusive. This equates to: Discovery rate θ = 0.9 t/A$1 M Two-thirds of this gold has been found in the Yilgarn craton of Western Australia (6265 tonnes Au). Without this exploration success, there would have been no platform on which to build the current gold industry and to take advantage of elevated gold prices and advances in mining and processing. Several causes of the Western Australian gold success have been proposed, and more than one may be correct. Gold price, and mining and processing advances have all had influence; but exploration success and discovery of gold were essential to add to the miniscule resource base of 1979. A comparison of the exploration methods used to search for gold in the Yilgarn craton in 1979, and 1990, highlights a small number of breakthrough ideas introduced to the industry during the 1980s, and in most cases emanating directly from local R&D. By the 1990s, these ideas were being used in most gold exploration programs in the Yilgarn craton, and are still used today. These six breakthroughs are: epigenetic timing of gold deposit formation (ie after formation of rock sequence), chemical and mechanical role of host rocks, relevance of carbonate alteration haloes, gold dispersion in the regolith, optimal sampling media, and appreciation of landforms in exploration program design. Interestingly, gold exploration science in Western Australia entered the 1980s period without rigid paradigms in place regarding gold deposit formation; there was a balance between descriptive and genetic models, there was scope to research gold deposits from microscopic to global scales and there were highly effective industry research uptake processes in place: it is suggested here that these favourable conditions contributed to the exploration success and industry growth.

Jan 1, 2007

By Vynne J. F

Drill monitors for rotary blasthole drills have been available to the mining industry since the 1970s. The early monitors were pen strip chart recorders that were developed for the oil drilling industry and adapted to mining. They recorded drilling parameters such as depth, pull-down pressure, torque, RPM, and hailing air pressure. While these recorders could generate a large volume of paper, the amount of useful data was minimal. The data was not summarised and required an engineer to interpret the chart traces. Being a mechanical recorder, the devices were also susceptible to frequent failures. Modem electronics, and the development of the personal computer and its associated software have radically changed the type of instrumentation that is now available for blasthole drills. Perhaps more important is what can be done with the data. The PC allows the logged data to be analysed, summarised, and a variety of reports to be generated. The reports can be customised to meet the specific requirements of the mine and reduce the amount of time that is required to interpret the data. There is also an increased awareness in the mining industry of the importance of production drills. Blasthole drills have typically been the piece of production equipment that received the least amount of attention in a surface mine. Management focussed on the trucks and shovels or draglines. This situation is changing, and therefore the benefits that can be derived from monitoring drill performance are being recognised. Potential economic benefits of installing drill monitors have been documented in previous papers (Peck and Vynne, 1992). Mines are finding that pay-back periods of less than twelve months and rates of return in excess of 30 per cent are not uncommon. These benefits include the following: 1. Reduced overdrilling; 2. Increased rate of penetration; 3. Helping to locate coal seams; 4. Identification of weak and strong zones; 5. Reduce geophysical logging; 6. Optimising blasts; 7. Improved fragmentation and diggability; 8. Decreased coal dilution; 9. Increased bit life; 10. Reduced maintenance costs; 1 I . Improved accuracy of data and reports.

Jan 1, 1995

By J Cook, S Pike, D Pridmore

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The application of high-resolution seismic reflection to map structure and/or mineralisation in hard rock environments has progressed significantly in the last decade. Improvements in equipment, field practice, processing and understanding has seen the seismic reflection technique emerge as a cost-effective tool for high-resolution three-dimensional structural and lithology mapping to depths far greater and with superior accuracy than other more conventional geophysical techniques.This paper outlines results and preliminary interpretation of 2D and 3D seismic reflection surveys aimed at defining fault zones and locations for quartz load development in favourable host lithologies at the Cracow low-sulfidation epithermal gold system in Queensland, Australia.As this is possibly the first time that high-resolution seismic reflection data has been used to define the structurally-controlled location of low-sulfidation epithermal gold mineralisation, an important aspect of this work was the derisking or due diligence steps taken prior to commissioning the full 3D surveys at each site. This included full wave sonic logging, vertical seismic profiling and trial 2D lines. Interpretation of the 2D profiles and the drilling of interpreted structure provided the confidence to proceed with the full 3D survey.The advantage of collecting 3D data extends beyond ensuring that the received reflections are located correctly in 3D space. The final 3D data cube can potentially map the entire fault network, thus highlighting flexures and changes in orientation of the structures both vertically and along strike, which is an important aspect in the deposition of gold and for direct targeting.CITATION:Smith, R, Cook, J, Pike, S and Pridmore, D, 2015. Application of high-resolution seismic reflection surveys to exploration for blind vein systems at the Cracow low-sulfidation epithermal field, in Proceedings PACRIM 2015 Congress, pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By R Ashworth, S J. Hall

During trials which began in May 2005, traditional steel dump bodies for transporting iron ore on 220-tonne haul trucks at a Labrador iron ore mine were compared to a novel rubber suspended dump body. Loads were measured and compared over some 93 700 loads, representing more than 20 Mt transported. Maintenance costs and downtime were also measured over the course of the trial, which lasted nearly one year. This paper outlines the parameters and results of the trials. Parameters measured included payload and production improvements, carry-back reduction, downtime due to body maintenance, and wear on the floor of the suspended dump body. These parameters were then compared to those for conventional steel dump bodies in use at the mine, and conclusions were drawn. The resulting comparisons were significantly positive in favour of the new suspended dump bodies, confirming that each truck could haul an additional 41 000 tonnes per year, that downtime hours could be considerably reduced, and that body availability and service life can be extended through use of the suspended dump body. There was also a high level of operator acceptance of the suspended dump bodies due to less loading shock and a smoother ride.

Jan 1, 2007

Mineralisation adjacent to Herberton occurs within three main subcentres. The Her- berton Hill subcentre is characterised by the association of Sn,W the Herberton Dividing Range South subcentre by Sn, and the Herberton Dividing Range North by Cu, As. The relation- ships between the subcentres are discussed in terms of metal distribution, production, deposit types, wall rock alteration and re- lationships with granitoid intrusives. The temporal and three dimensional spatial re- lationships between the centres are uncertain.

Jan 1, 1978

Instantaneous outbursts have occurred at Metropolitan Colliery from the pick and shovel work of early days to the modern mining techniques of today. Developments have been the introduction of an emission index to measure the proneness of the coal to outbursts, drainage and destressing by large diameter holes, attempts at higher productivity by the introduction of pulsed infusion shotfiring and improvements in ventilation. The future plans and aims for the Colliery include prediction of outbursts, seam gas pre- drainage and longwall mining.

Jan 1, 1980

By S Wotherspoon

At Kalgoorlie Consolidated Gold MineÆs (KCGMÆs) Fimiston Operations, located on the periphery of Kalgoorlie Boulder in Western Australia, roughly 7.5 million tonnes of rock are broken each month for the extraction of gold. With the close proximity of neighbours to the mining operations in the Chaffers Cut Back, special blasting techniques and tools were employed by KCGM to manage the blast induced vibrations and noise in this area. The i-konTM initiation system coupled with OricaÆs complementary modelling and analysis tools offered the complete blast management package. With these tools KCGM management and Orica Mining Services commenced an investigation into the benefits of electronic initiation. Prior to the commencement of electronic blasting, initial modelling was conducted to examine the vibration time waveforms and their frequency content, as these were expected to have an impact on vibration interaction with structures such as large buildings and urban dwellings. This work looked at results measured for a previous conventionally (pyrotechnic) initiated blast in the area and compared it to the results obtained when the blast was modelled with electronic initiation and faster timings. The predicted peak particle velocity (PPV) and structural vibration factor (SVF) were calculated. From the results it was concluded that the investigation into using i-konTM electronic initiation system and SHOTPlus«-i blast design software had some real potential to improve blast vibration management on the cut back. The use of the electronic initiation system and complementary software allows intricate timing designs to be accurately placed into blasts. The system has a number of working modes that allow either the precise design timings to be logged automatically into each detonator or to be manually logged where a variation from the design exists. Where such variations from the design occur, the electronic system permits the actual timings used to be uploaded back into the design file. This allows both design and real actual timings to be stored for future analysis or reference.

Jan 1, 2004

By Paterson M. R, Spencer P. A

Vitrokele technology is a resin process that can be applied in gold plants to reduce both capital and operating costs. The Vitrokele resin can be used for both precious metal recovery and for recovering free and combined cyanide from effluent streams. Vitrokele resin has been extensively tested at pilot plant level and is now applied successfully at a commercial heap leach facility in Zimbabwe where it is used in place of activated carbon for recovery of gold from pregnant leach solution. Significant capital cost savings were achieved by installation of a resin plant instead of a conventional carbon adsorption plant. Operation to-date has not seen any significant physical or chemical degradation of the resin either in terms of adsorption capacity/kinetics or physical appearance/size. This gold recovery process is equally applicable to slurry streams where it would be implemented in stirred tanks with interstage screens in a similar manner to a conventional carbon adsorption plant.

Jan 1, 1996

By M, C A. RosiFre, R C. Figueiredo e Silva

Jaspilites and underlying basalt contacts of the Archaean volcano- sedimentary Grpo Parß Group, Carajßs, host giant iron mineralisation in the ~100-km long, E-W trending Carajßs fold. Preliminary, unpublished geochronological data point to a Palaeoproterozoic mineralisation event. Geochemically, jaspilites are typical volcanogenic banded iron formations. Basalts exhibit evidence of spilitic seawater interaction. Iron-associated hydrothermal alteration of mafic rocks was induced by fluid infiltration in amygdales, with development of chlorite- and hematite-dominated zones. In the case of jaspilites, iron mineralisation encompasses: partial replacement of jaspilitic microcrystalline hematite by blasts of martitic magnetite; jasper recrystallisation, producing fine-grained, hematite-free granoblastic quartz; martite recrystallisation, forming lobate¦subhedral hematite; pervasive porosity development by quartz-chert leaching; incipient cavity filling by microlamellar hematite; and advanced filling by coarser, euhedral and comb-textured, tabular- shaped hematite.Peak hydrothermal ore textures indicate typical epithermal-crust conditions, supported by preliminary fluid-inclusion calculations at 160 - 200¦C. Such temperatures and extreme fluid-to-rock ratios during alteration must have exceeded the ambient metamorphic conditions, with the infiltrating fluid relatively hot and capable of leaching SiO2. Therefore, mineralisation developed over exhumed, Archaean, brittly deformed rocks, with mineral associations representative of very low- to low-grade metamorphism. Considering that chlorite (¦talc) abounds in mafic rocks; hydrothermal albite is developed; dolomite fills veins and vugs; the typical rare-earth-element (REE) pattern of jaspilites is significantly modified in higher-grade hard hematite ores (higher LREE); pyrite, copper sulfide minerals and rare gold occur in association with carbonate-quartz-rich alteration zones, it is suggested that an alkaline, H2O-Fe-CO2 mineralising fluid dominated, also containing species like S¦Cu¦Au. Peak-mineralising conditions are likely to have resulted from a single, evolving fluid, via incipient- through advanced-stage alteration phases. The porous, high-grade soft hematite-type ore (SH), rich in microlamellar and anhedral hematite, must have derived from interaction with this relatively hot SiO2-leaching fluid, whereas the high-grade massive hard hematite-type ore (MH) developed due to closer fluid-rock temperature equilibrium conditions, attained by mineral reactions, with relative increase in the Fe/Σcations ratios allowing the precipitation of subhedral-tabular hematite that partially cements the soft-hematite ore. SH and MH hematite ore types must thus reflect intermediate and high fluid:rock ratios, respectively. Since the N5 deposit is to date understood to contain the largest amount of the MH ore, its units are interpreted as the loci of the highest fluid:rock ratios in the district. Preliminary mineralogical information regarding the S11 deposit of the Serra Sul (south range) implies higher-temperature conditions. The near-equant grain size and the granoblastic intergrain relationship, coupled with the presence of riebeckite, augitic pyroxene and garnet, suggest hornfels textures. The data collected, though still relatively sparse, permit the speculation that the immense driving force for the Carajßs world-class iron deposits was a relatively shallow, igneous-related hydrothermal system. If such a model is correct, then the Carajßs Palaeoproterozoic iron deposits could represent an end-member of the iron oxide-copper-gold hydrothermal system in the province.

Jan 1, 2005

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996

Surface oxidation is one of the most important factors that influence the flotation selectivity and recovery in the processing of complex sulphide ores. It is an inherent part of surface chemical reactions that determine whether the surface film formed on a sulphide mineral will act as a hydrophobic or hydrophilic one. Because of the highly complex surface chemistry and mineralogy involved the results of flotation tests may often be difficult to interpret. In this paper, the flotation behaviour of nickel-copper ores processed in the Sudbury area is discussed with emphasis on the effect of oxidation on individual minerals, primarily pyrrhotite. In general, moderate oxidation of a freshly ground ore promotes the flotability of all principal sulphides in the ore leading to a bulk flotation concentrate. The ease of individual mineral flotability under normal aeration conditions, which is chalcopyrite > pentlandite > pyrrotite, changes to pentlandite > chalcopyrite > pyrrhotite under oxygen-deficient conditions. This behaviour is correlated with the catalytic activity of these minerals for oxygen reduction. On the other hand, preferential oxidation of pyrrhotite may lead to a selectivity increase in flotation. Such a behaviour has been noted in the flotation of a pyrrhotite-rich process stream. The results have been discussed in the light of fundamental electrochemical interactions involving pentlandite, chalcopyrite, pyrrhotite, pyrite and grinding media and a mechanism has been proposed to explain the selectivity.

Jan 1, 1993

By Valenta R. K

Copper-gold deposits associated with iron oxide rich rocks (ironstones) form a distinctive and significant ore association which occurs widely, but not exclusively, in the Proterozoic. The ironstone association is geochemically distinct from the BIF-hosted gold association (Phillips and Groves, 1983). Not only is the former association higher in its copper and commonly uranium, FEE, ¦bismuth, molybdenum contents, but also the ironstones in many cases do not originate as chemical sediments. Although both associations form in metamorphic environs, they reflect differing tectonostratigraphic settings and with consequent differences in ore-forming fluids and ore-forming mechanisms. This paper discusses the nature and origin of the ironstone-related copper-gold association, with particular reference to the Tennant Creek district in northern Australia, and emphasises the two stage origin of mineralisation. The genetic model developed has significant implications for other ore-bearing environments.

Jan 1, 1990

By P Cavieres, R Dunlop, S Gaete

El Teniente Mine started the exploitation of the primary rock in the beginning of the 1980s decade, using caving methods. Since the beginning the mining activities have induced seismicity including some occasional rockbursts. Owing to the relevant damages, the mining operations were stopped in some production sectors. This paper describes the concepts that have been used in order to control the induced seismicity based on the strategies for controlling the rockmass breaking process, which depend on mining parameters. It also presents the main concepts applied in the Teniente Sub6 sector design and the experience collected during its sector exploitation.

Jan 1, 2000

By McClarnon D. J

This paper aims to provide the reader with an insight into the field of computer graphics and Virtual Reality (VR), and show how both have been applied to the general area of Free Steered Vehicle (FSV) operations underground. It first explains this developing computer technology and explains its advantages over existing CAD based solutions. This paper deals with the graphical applications and implications of building models within a computer's memory. It then continues to describe the problems with Free Steered Vehicle operations. The work already carried out in the field of VR is explained, and the production of a VR system addressing the problems with fitting cameras to aid the driver's field of view is detailed. Another possible use of VR is also explained - the concept of risk regions, demonstrating its uses in the examination of proposed operational methods. Examples of possible uses are given, and its potential advantages over existing methods discussed. A case study of a computer-generated video involved with the safety of operations of FSVs is also presented. This addresses the precautions that pedestrians should take to ensure safe working in areas where FSVs are operating. This paper then concludes with possible further applications for computer graphics and VR, and the on-going research into these two technologies.

Jan 1, 1995

By Graham JW, Cullen GV

edicted increase in, Aluminium production and the possibility of a diminishing supply of petroleum coke for anode electrodes in alumina reduction cells makes it desirable to find alternative electrode materials. Brown coal char, with a lower ash content and with an elemental purity similar to petroleum coke, has been produced by leaching in hydrochloric acid, washing with water and charring at 115000. The cost of processing is estimated to be competitive with petroleum coke. Without further processing the bulk density and real density were undesirably low, but. by briquetting the coal before charring and crushing, the bulk density was improved to 92 per cent of the petroleum coke value and the Particle density was improved to 92 per cent of the density of petroleum coke by water-displacement or 75 per cent by mercury displacement. Pre-baked electrodes were prepared from the char alone, mixtures of petroleum coke and char and from petroleum coke alone, all bonded with coal tar pitch. The electrodes were tested for the usual physical properties and were, evaluated for performance in a laboratory size alumina reduction cell. Electrodes based on brown coal char alone were found to be inferior in physical properties, and performance, but mixtures of the char and petroleum coke, despite poorer density, electrical resistivity and carbon consumption on a theoretical basis, in performance tests gave up to 17 per cent better carbon consumption per weight of aluminium produced and 21 percent better electrical current efficiency than the electrodes based on petroleum coke alone. It is suggested that larger scale tests are warranted.

Jan 1, 1970

Until recently, nickel laterite projects have been largely ignored, due to their supposedly higher treatment costs compared with sulphides, and to their perceived processing difficulties. A number of laterite projects in the 1970s were abandoned because of high capital and operating costs, while others experienced severe technical difficulties. Conventional wisdom had it that laterites would not be exploited until most of the sulphide orebodies had been depleted. Why then, have Australian mining and exploration companies started a resurgence of interest in the treatment of nickel laterites? It all began with the Bulong project, which has been under study since 1987, while more recently two further projects, Murrin Murrin and Cawse, have been initiated and are being fast-tracked to take advantage of the current high nickel and cobalt prices. A further project in NSW, Syerston, has also been investigated at bench-scale, but no further development has yet been announced. All these projects have the following advantages: 1. Good location near a major mining centre and,reasonably close to power, water, roads, accommodation and a developed service industry. 2. Straightforward, low cost mining. 3. Low cost of acid or sulphur. 4. Good to very good cobalt credits. In addition, there have been significant technological developments in the design and operation of high pressure autoclaves and high rate thickeners, as well as solvent extraction and electrowinning technology. This has helped to decrease capital costs and technical risks, and has allowed the development of alternative flowsheets to the existing laterite operations (Taylor, 1996).

Jan 1, 1996

By S M. C Verryn

Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis of metallurgical products. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine process control. Knowledge of the crystal structures of the major phases is essential for Rietveld analysis, and these are well known for most minerals and major phases in metallurgical products. It provides the basic structural information necessary for the determination of mineral stoichiometry and for elucidating solid solution behaviour. Modern methods, such as simulated annealing and charge flipping, permits the determination of crystal structures from powder data. Unit cell data can be used where conventional microchemical analysis is unable to provide an answer to the extent of solid solution in ilmenite roasting. Unit cell data (by XRD) is used to determine the amount of roasting necessary for the development of magnetisation to be able to separate chromite from an ilmenite concentrate. Phase quantification is probably the most widely used application of XRD analysis. It is used for materials balance in the minerals and cement industries, and it is finding novel applications in the iron and steel industry. Applications of XRD in high-temperature metallurgical processes are increasing. In this paper the phase chemistry of iron ore sinters, the evaluation of subsolidus reactions in titania slags and the identification of furnace accretions are discussed. Despite the success of the Rietveld method in phase quantification, the method still needs further development in the quantification of closely related or polytypic phases. The quantification of pyrrhotite phases using various Rietveld programs still gives ambiguous results. This is also true for the different SFCA phases in iron ore sinters. Clearly the analysis of similar phases, differing only in the presence of weak superlattice reflections is still problematic.

Jan 1, 2008

By Weimin F

In the last decade, great strides have been made in the raise boring technique in China. Extensively, the drilling and blasting method has been replaced by the mechanized raising method since 1980. There are now over 3C raise drills operating in more than 20 mines. The diameters for shaft boring varies from 500mm to 2000mm, and to depths up to 90m. Tlis paper mainly describes the performance, mtLin technical achievments and applications of all four kinds of raise drills, and auxiliary equipment. Finally, some recommend- ations for future improvement in the raise boring technique are presented also.

Jan 1, 1987