Search Documents

The completion of the Hot Strip Mill at the Port Kembla works of Australian Iron & Steel Ltd., makes possible the production of steel plates and wide strip of a quality and in quantities not possible previously in Australia, and will also enable the production of tinplate to be undertaken in this country.The site chosen for the mill was a mud fiat underlain by a hard stone bottom at 5, to 801 feet below the surface; and a total area of one hundred acres was reclaimed to a level of 20 feet above the original surface.Three adjoining buildings were constructed to house the slab receiving yard, mill equipment and electric drive, together with the plate finishing line.After slabs have been heated to 2250°F at a rate of 90 tons per hour, they are transferred to the vertical scale breaker which is the first stand in the hot roughing mill. Here the primary furnace scale is first cracked and then blasted off by high velocity water descaling sprays.The next stand is the horizontal scale l;Jreaker, where any remaining primary scale is broken and then blasted off. After descaling, the slabs pass to the broadside mill, where short slabs are turned and rolled on broad side for wide plate.The next step is a slab squeezer which squares up the edges after broadsiding ready for the reversing mill. This is the finishing stand for plate and the last roughing stand for strip, which then passes to the finishing mill.The hot strip finishing mill consists of six stands with a maximum finishing speed of 2,230 feet per minute. Strip is cooled for coiling by water sprays on a hot run table and then coiled on a mandrel type downcoiler, from whence coils of hot strip are weighed and transferred by conveyor to the coil storage building.Plates are transferred from the reversing mill to the plate finishing line where operations consist of levelling, inspection, branding, cutting to width and length:INTRODUCTIONDue'to the increasing production of cars, refrigerators, washing machines and similar consumer goods in Australia, together with the increased requirements of galvanised iron...

Jan 1, 1956

The sulphide ores of the Kalgoorlie goldfield have long been looked upon as' refractory, involving special metallurgical treatment. For many years two kinds of treatment have been practised-(l) wet treatment, including fine grinding, amalgamation or concentration of the free gold, concentration of the sulphide minerals with subsequent roasting and cyanidation, and cyanidation or bromo-cyanidation of the residue from the concentrating operation; (2) dry-crushing of the ore and roasting the whole of thecrushed ore, amalgamation of the gold in the calcine during fine grading, followed by cyanidation. The wet treatment was advanced a stage further when, in 1929, the Lake View and Star Ltd. adopted large scale flotation. As a consequence, however, further metallurgical problems were introduced. This paper covers the investigation, ,of one of the most prominent of these problems.Flotation preceded by strakes was satisfactory to a point.The flotation concentrate consisted largely of auriferous pyrite and tellurides, and the gangue minerals in the concentrate were practically barren.Several sources of loss of gold values were, however, found to be associated with this circuit, viz.-(a) There was the loss of gold in the flotation tailing.(b) Loss by dusting during roasting of the flotation concentrate.(c) Loss of gold in the cyanided residue.

Jan 1, 1937

By Burgess JM

Research on gas distribution in the iron- making blast furnace has been conducted in three separate areas. Firstly, experimental work has been conducted to determine the important parameters which dictate the pressure losses in homogeneous and heterogen- eous packed beds. Secondly, a theoretical analysis of gas flow through the furnace softening-melting zone has been undertaken to determine the effect of the shape of the zone on the distribution of gas flow towards the furnace walls. Thirdly, a theoretical programme has been undertaken to develop methods for the prediction of furnace soften- ing-melting zone shape from furnace tempera- ture and gas composition measurements.

Jan 1, 1980

By Liu Wenyong, Huang Yucheng, Yang Ba

High-water rapid-solidifying material, called æhigh-water materialÆ, is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of backfill body, environmental contamination and so on, have been solved.

Jan 1, 1998

By Sharpin PC

The countercurrent gas-solid-heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temp-erature distributions through the drier have been calculated. Although the calculations rest on several simplifying assump-tions, to be corrected as the experimental work develops, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating con-ditions on the rate of drying of the briquettes which-controls the 2 strength of the char produced. The analysis shows why a limitation was reached in the improvement of char-strength in the pilot plant in 1961 and a prediction is made of ' a way ' in ' which the limitation could be overcome.

Jan 1, 1963

By Manca PP, Rossi G, Lipari D, Knissel W, Massacci G, Licheri P, Fioravanti E, Helms W, Lai S

Mining of the massive complex sulphides orebodies of Campo Pisano and San Benedetto (Southern Sardinia, Italy), dates back to before Christ, though their exploitation with modern technology was only resumed in the middle of the last century. The increasingly adverse economic conditions and the weakness of both country rock and mineralization were concurrent in forcing the Company's management to develop suitable high-productivity stoping methods. In the framework of a project fi- nanced in part by the Commission of the European Coranunities, and carried out in cooperation with the Universities of Cagliari (Italy) and Clausthal (Germany), a cemented backfill stoping method was developed. The concrete mix preparation and placement facil- ities, study of the cement mixes and endeavaa-s to optimize the methods are described. The monitoring system for measuring stress evolution within the emplaced backfill is illustrated together with the successful replacement of part of the Portland cement

Jan 1, 1992

By Brumley J

The development of the SECV brown coal open cut at Loy Yang will require depressurisation of aquifers both within and below the coal seam sequence in order to maintain open cut stability. Prediction of future open cut dewatering requirements at Loy Yang Open Cut and evaluation of the regional consequences of dewatering has required development of a detailed hydrogeological model of the Loy Yang area. The complex stratigraphy of the coal seam and aquifer/aquitard sequences at Loy Yang have been analysed and integrated with the hydrogeological concepts developed from regional groundwater studies to formulate a realistic hydrogeological model as a basis for finite-element flow modelling.

Jan 1, 1988

By Dight P. M

The challenge of narrow vein mining is to produce ore with as little dilution as possible, at the least cost -commensurate with the increasing degrees of safety being demanded for mine workers by the modem 'duty of care' legislation. Geotechnical factors play an important, if not overriding, role in these areas. The geotechnical factors cover the complex interaction over a period of time, between the in situ and induced rock stresses, rock structures, rock mass strength and the cable, rock bolt and other ground support members. In the Archaean schist belt areas where many of our narrow vein mines occur the pre-mining in situ rock stresses are commonly significantly higher than the overburden stresses. These are concentrated in areas beneath previous open pits and may be highly concentrated in the pillars and abutments of stopes on narrow veins. The presence of high in situ stresses may be suspected from the appearance of drill cores and underground development long before they become sufficiently concentrated by mining to cause damage or bursts. These initial indications are discussed and modem low cost methods of stress measurement are described. Practical and quick methods of analysing the stress redistribution around scopes and other underground excavations are now available and guidelines for interpreting them in terms of rockmass characteristics, stope stability and support requirements are developed with the object of increasing safety, whilst reducing overall costs and dilution.

Jan 1, 1993

Gold deposits in Eastern China have characteristic of belted distribution. The concentrating belts of gold mineralization are about parallel to the island are belt in Western Pacific Ocean. Gold deposits are mainly concentrated in the aged metamorphic rock series on the upwarping zones and upwarping fault zones, and obviously controlled by the deep fractures and their deriva-tive secondary faults. Gold mineralization had genetic relation to the Mesozoic (especially Yanshan period) magmatic activity. The distribution and genesis of gold deposits can be explained by the assumption of wavy structure. The formation of wavy structure is related to the process of Pacific plate and India plate.

Jan 1, 1990

On-line radioisotope gauges determine information on the characteristics of ore to enable improved control of processing operations. In the metalliferous mineral industry, in-stream analysis systems based on radioisotope X-ray techniques determine concentrations of valuable minerals at various stages of the concentration process. In the coal industry, on-line gauges determine ash and moisture contents, and the specific energy of coal.In-stream analysis systems developed in Australia are installed in about 30 mineral concentrators. Their use has led to the increased recovery of valuable minerals, and the time taken to recover the cost of installation is usually several months. The savings to Australia resulting from use of these analysis systems is estimated to be more than $A 15 million per year.Australian experience in the training of mineral industry personnel shows that the most effective approach is to combine courses on nuclear techniques and control of processing operations. This is the basis of Australia's contribution to the minerals sub-project of the United Nations Development Program (UNDP) Industrial Project.

Jan 1, 1985

By Barro L

There is currently a world wide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow charac- teristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A Capillary rheometer, designed to handle settling suspension, has been used for deter- mining rheological properties. Brown coal of 0 0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦- 319¦C, Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physico- chemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage.

Jan 1, 1980

By Kidd CH

The excavation of a coal mine or any other mine, tunnel, or quarry, below the water table establishes a void towards which ground- water will flow. Inflows into the mine, if significant, can cause not only problems such as flooding, and/or muddy floors, in the mine, but commonly also require disposal of poor quality groundwater. The flow of groundwater towards a mine is accompanied by a decline in groundwater levels, which may extend up to several kilo- metres around the mine. This may seriously effect vegetation, stream flow and existing users of groundwater. At the pit face groundwater gradients can also cause slope stability problems and where a water table is intersected, increase blasting costs.

Jan 1, 1983

The research, development and testing of a Blast Control Plug (U.S. Pat. #4,754,705) funded by the U.S. Department of Energy is described. The plug's function is to improve blasting efficiency through the enhancement of stemming effectiveness and thereby reduce drilling and blasting costs. The plug comprises a solid unit placed in the blast hole within the stemming column above the explosive. It is designed for use with back filled drill cuttings or any other suitable material The research and development program comprised the testing of the plug in small diameter holes in competent rock for both bench and crater blasting configurations and full scale field trials in multiple hole and row blasts using blast holes of from 76 to 387 mm in diameter. Test measurements included stemming displacement and velocity, face movement and extent, peak air over pressure and ground surface peak particle velocity. Data acquisition equipment included a Spin Physics SP2000 high speed video motion analysis system, and acoustic and seismic monitoring units. Substantial reductions in stemming ejection velocity or ejection elimination were achieved whilst reducing stemming length by up to 35% over conventional practice. Peak air blast pressures were also reduced by between 8 and 25 dB. A strong inverse relationship between rock face movement and stemming ejection velocity was found. The implications of the importance of stemming effectiveness in blasting and computer blast simulation is also addressed.

Jan 1, 1990

Pongkor Gold Mines is one of seven units of production owned by PT Aneka Tambang (State owned mining company). The mine is located in the western part of Java Island, Indonesia. It is in the Bogor District and approximately 110 kilometres to the south of capital Jakarta. It is located in very steep hilly terrain intersected by many river valleys and the mine site is approximately 500 metres above mean sea level (see Figures 1 and 2 - Mine location map and picture)

Jan 1, 1997

The Energy Authority of NSW has wide powers and responsibilities conferred by its Act which are pertinent to the State's coal industry and its development into the next century. With respect to coal, the broad objective is to maximise the benefits to NSW and its people derived from the State's coal resources. The initial focus of the Authority's coal-related activities in the late 70's and early 80's was on petroleum substitutes from coal. Research was supported, especially on hydrogenation, and the Authority participated in the Joint Australia/Federal Republic of Germany coal-to-oil feasibility study. It also co-ordinated a State Government initiative to involve the private sector in examining the possible establishment of a synthetic fuels industry based on Hunter Valley coal. With a short-fall in world-wide petroleum supply now seen as less likely for some years, the Authority is looking also at ways of working towards the broad objective in the field of coal utilisation on both domestic and export markets. Areas of interest include possibilities for using washery rejects, means of making NSW coal more competitive as an energy source, use of coal-seam gas and new or special technologies for burning coal. The future is expected to see renewed interest in producing petroleum substitutes, and coal - as the State's major energy resource - is seen as a strong contender as a basis for such an industry. Developments in coal-based power generation are also expected to have an impact, with advanced technologies having a possible place here as well as Overseas.

Jan 1, 1987

By Barlow S

The Kelian Gold mine project won two excellence awards from the Victorian Division of the Institution of Engineers, Australia. It was a challenging project, fast tracked in a remote and inhospitable tropical environment. The creation of a profitable and efficient mine was a significant engineering and project management achievement. The difficulties encountered and the way they were managed provide valuable lessons. These include the importance of sufficiently detailed engineering in all aspects of the job to enable the best estimates possible to be prepared during feasibility studies, the need to prepare the project scope and execution plan with disciplined and rigorous attention to detail by a highly experienced team and the value of identifying, assessing and mitigating risk and uncertainty during execution. The practical benefits of applying these lessons were demonstrated in the successful management of technical uncertainty on the recent diversion of the Kelian River to allow the expansion of the Kelian mine.

Jan 1, 1997

By D Bradshaw, J R. R de Villiers

The non-stoichiometric sulfide mineral pyrrhotite (Fe(1-x)S), common to many nickel and platinum group element (PGE) ore deposits, occurs in varying crystallographic forms with the different types exhibiting subtly different physical and chemical properties. These differing properties are likely to influence the flotation performance of pyrrhotite, which in the case of PGE operations is actively recovered, whereas in nickel operations pyrrhotite is depressed. In this study, examination of natural pyrrhotite samples from Southern African and Canadian nickel and PGE ore deposits revealed a variety of pyrrhotite compositions in terms of iron content (Fe7S8, Fe9S10, Fe11S12) and solid solution nickel concentration. Pyrrhotite composition was correlated with its mineral association depending on whether non-magnetic pyrrhotite occurred in conjunction with troilite, non-magnetic pyrrhotite occurred as single phase pyrrhotite, magnetic pyrrhotite occurred as single phase pyrrhotite or whether the two phases; magnetic and non-magnetic pyrrhotite co-exist. Subsequent microflotation tests of selected single phase pyrrhotite samples revealed that the non-magnetic pyrrhotite is slightly more floatable than magnetic pyrrhotite. Microflotation tests also showed that varying flotation responses occur between differing magnetic pyrrhotite samples. These differences in flotation performance are postulated to be a result of the effects of varying pyrrhotite crystallography, trace metal content and mineral association on pyrrhotite oxidation, formation of surface species and subsequent adsorption with xanthate collector.

Jan 1, 2008

Most types of nuclear power reactors use uranium dioxide fuel. Power reactors using natural uranium dioxide'fuel are of special interest to countries such as Australia that have their own uranium supplies. A wide range of uranium dioxide powders can be fabricated and the ideal one flows readily, presses without the need for binders or lubricants, sinters to the required density and gives low reject rates at all fabrication stages. Sinterable uranium dioxide is usually produced via the ammonium diuranate route. The A.A.E.C. is aiming to demonstrate production of nuclear grade uranium dioxide from Australian concentrates, improving technology where possible. Details are given of the dissolution, solvent extraction, precipitation, filtration, drying, and calcination-reduction steps. Solvent extraction from sulphate media is also under study with a view to developing a process to produce a nuclear grade product at the mine treatment plant site,

Jan 1, 1969

By T Baumgartl, M Edraki, L Huang, D R. Mulligan

"Phytostabilisation with tolerant plant species has been advocated as a cost-effective solution for sustainable cover of tailings from metal mines and bauxite refinery. The development of sustainable plant ecosystems on such wastes requires not only tolerant plant species compatible with local climatic conditions, but also the formation of stable and functional root zones through systematic processes to develop functional soil matrix and horizons (eg A-B-C). However, the process requirements for reconstructing functional root zones in tailings are poorly understood. Based on a review of current literature and industry experience in tailings revegetation, the present paper conceptualises three key phases in the process of root zone development in amended tailings: hydro-geochemical stabilisation resulting from the interactions among tailings characteristics, amendment measures and local climatic conditions the rehabilitation of soil biological capacity the establishment of ecological (carbon and nutrient) linkages between the rehabilitated root zones and the above ground plant communities.Key research is required on: the relationship between hydro-geochemical stability and mineralogy and geochemistry of tailings, in response to rehabilitation treatments under local climatic conditions the relationship between soil biological capacity and hydro-geochemical stability in the root zone the transition of soil microbial communities specific to exogenous organic matters into those required for mineralising litters of in situ plant communities.CITATION:Huang, L, Baumgartl, T, Edraki, M and Mulligan, D R, 2012. Sustainable phytostabilisation of mine tailings - A critical analysis of system requirements and approaches, in Proceedings Life-of-Mine 2012, pp 105-116 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By Mogi G, Akaike A, Yamaguchi U

A new algorithm has been investigated for three-dimensional open pit designs to improve the dynamic cone approach which utilises the dynamic programming technique. The conventional dynamic cone method was improved by introducing examination processes: 1. whether any negative blocks are included in a unit cone or not; and 2. whether it is possible or not to leave the negative blocks unmined in the unit cone without disturbing the geometric condition imposed on the slope angle of the cone. The newly developed algorithm was applied to a large-scale open pit copper mine in a planning stage and the results have been compared with those obtained by the conventional methods.

Jan 1, 1995