Search Documents

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By E J. B van Etten

Pit lakes may form when open cut mining leaves a pit void that then fills with ground and surface waters. This often replaces terrestrial ecosystems that existed prior to mining with an aquatic ecosystem, affording an opportunity to improve regional aquatic biodiversity values through targeted aquatic restoration (McCullough and van Etten, 2011). Restoration theory provides guidance when restoring disturbed systems towards landscapes that are of regional value and relevance. But how do we identify a restoration target for a novel aquatic habitat that only exists in the new post-mining landscape? This paper presents a process of first identifying and then surveying local representative aquatic systems, to provide a direction for pit lake restoration efforts and achievement criteria for pit lake relinquishment, using a case study from a sand mining operation amongst wetlands in south-western Australia.The company mines silica sands following mechanical removal of topsoil and then extraction of the ore from below the watertable by dredging. Assessment of wetland and riparian vegetation was achieved through the establishment and measurement of temporary monitoring transects across five natural wetlands in the Kemerton area. Several more regional wetlands were also visited and observations made to supplement and validate these data.Distinct vegetation zonation was found across each wetland, although typically wetland basins were unvegetated or filled with younger woody plants with patchy distributions. Fringing riparian vegetation consisted of few species (commonly the paperbark Melaleuca rhaphiophylla and the sedge Lepidosperma longitudinale), but community composition and structure were variable between wetlands. The pattern of vegetation seen across natural wetlands was best explained by topography and soil chemistry, with low lying wetland areas more likely to experience regular flooding and accumulate organic matter and nutrients.In conclusion, where they are available, regional natural waterbodies may constitute the best valid restoration goal. Nevertheless, the goal may need to consist of a range of closure design opportunities, rather than a single target.

Oct 5, 2011

In high stress mining environments, production drill rigs are often employed for rapid drilling of boreholes for systematic cable bolting. One outcome of this drilling method is the need for larger boreholes than would normally be drilled using customised bolting machines, such as the Tamrock Cabolter. Past laboratory studies indicate that, under ideal grouting conditions, borehole diameter has little effect on the pull-out strength of cable bolts with high bulb densities. However, the sensitivity of pull-out strength to large boreholes and less ideal variations of grout strength have not been investigated. To explore these sensitivities, industry standard single embedment tests were conducted on large boreholes simulated using steel pipes. Four borehole diameters were tested, namely: 42 mm, 52 mm, 81 mm and 106 mm. In each case the grout water to cement ratio was varied from 0.35 to 0.45 and two cable bolt bulb spacings were considered, namely: one and three bulbs per metre. The results indicate that, across the range of parameters tested, variations in peak axial load at failure corresponding to changes in hole diameter were statistically insignificant.

Nov 25, 2010

By F Clark, J T. Carswell

Ore definition for final stope planning is often a challenging prospect in underground (UG) gold mines which exhibit high geological and grade variability. Unlike the grade control (GC) scenario in an open pit (OP), the ability for the mining geologist to plan a sampling campaign which effectively characterises the underlying mineralisation is fraught with difficulty. UG sampling patterns are strongly clustered and typically not dense enough to characterise the spatial and statistical properties. Very commonly, sample volumes are not large enough to provide a reliable grade estimate of the surrounding rock. These factors critically affect our ability to accurately map out ore positions and estimate metal quantities.At Sunrise Dam, traditional UG sampling and modelling techniques have proven to be an unreliable strategy for successful stope planning and extraction. The problem was first observed during the final cut-back in the open pit for which the mineral resource model was constructed from UG diamond drilling. Open Pit grade control reconciliations were strongly positive for both tonnage and grade compared to the resource model. Underground workings missed significant quantities of ore which was laterally defined by open pit reverse circulation (RC) GC drilling. Upon examination it was realised that the cause of the problem was one of inadequate sample density and sample support, the implications of which potentially affected the entire UG mine.As part of a broader study into underground grade control procedures, detailed reconciliation of initial stope production from the GQ domain also pointed to inadequate sampling as a major constraint to effective grade control and reserve conversion.To overcome this deficiency, dense 115 mm wet RC grade control drilling and conditional simulation modelling has been successfully implemented with the intent to replicate the grade control process in the open pit. The increase in sample density and sample volume has proven to be a very effective tool for mapping out highly complex mineralisation. A marked improvement in stope definition, reserve conversion and Mine to Mill reconciliations has been demonstrated on the back of an innovative approach to UG grade control.CITATION:Clark, F and Carswell, J T, 2014. Using reverse circulation drilling to improve sampling in a complex underground gold operation – an innovative approach to underground grade control at the Sunrise Dam Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 143–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By S Bluhm, LádeáOliveira, R Funnell

Taquari Vasouras potash mine (Vale Fertilizantes) has many interesting features including virgin rock temperatures of 50¦C at depths of 700 m. The mine has a relatively small shaft system with limited ventilation carrying capacity, which was not adequate to exploit the full extent of the deposit. This limitation was overcome by installing two large-scale recirculation systems with underground reconditioning centres. This paper describes this unique mine ventilation and cooling system and some of its history over the past two decades. The two controlled recirculation systems have been operating safely for some ten years and the use of large-scale recirculation has been a fundamental component in the increase of production and extending the mining further-and-further from the shaft centre. The recirculation systems have played a huge role in the mine profitability and comprehensively extending the mine life. The paper also discusses a number of novel design and operating features such as reverse running pumps for energy recovery. The underground chilled water system design required a number of special safety features in order to minimise the risk of water leakage since this could be catastrophic in a potash mine. This paper describes a good example of a mine in which the final ventilation and cooling system design ends up very different to what was envisaged at the greenfields stage.CITATION:Bluhm, S, Funnell, R and de Oliveira, L, 2013. Controlled recirculation and refrigeration at ValeÆs Taquari Potash Mine, in Proceedings The Australian Mine Ventilation Conference , pp 237-248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

This paper describes the new iron and steelmaking process recently commissioned at NZ Steel. Ironsand mined and concentrated at Waikato North head is slurry pumped 18 km to the company's Glenbrook works. Ironmaking includes the direct reduction process pioneered at Glenbrook in the 1970s and a new continuous electric melter. The molten, high carbon pig iron produced is then fed to a vanadium recovery unit and on to the KOBM oxygen steelmaking vessel. Steel is cast into billets or slabs. The new plant, which is the first stage of a fully integrated works at Glenbrook, raises New Zealand Steel's production capacity from 150 000 t/y to 750 000 t/y.

Jan 1, 1986

By R McDonough

DTL2 contract C916 was awarded in March 2009 for S$340 M. This contract includes two mass rapid transit (MRT) 1100?m long bored tunnels using two slurry tunnel boring machines (TBMs), with an internal diameter of 5.8?m, two cross passages and 135?m of cut-and-cover tunnels The contract also includes the design and construction of a new underground station including station entrances, subway links, architectural finishes and external landscaping. The station, located at Upper Bukit Timah Road near Jalan Jurong Kechil will also double as a civil defence shelter.The works included significant traffic management in a dense urban area in order to create the working areas whilst keeping the requisite number of traffic lanes. This involved numerous utility diversions and included the removal of a 33-year-old pedestrian overhead bridge (POB) over busy Bukit Timah Road. The station and tunnelling works were completed on time, including a ‘dock and dismantle’ TBM retrieval and subsequent breakthrough of the separating wall.This paper will detail the methods and solutions used to construct the tunnels and stations, with a focus on the requirements for construction of the station to be a civil defence shelter if required. This involved solutions to tying reinforcement and placing concrete to high standards in a restricted space, as well as the incorporation of heavy blast doors and other associated protective measures. The efforts of the management team resulted in the project being awarded first prize in the 2011 Land Transport Authority’s Annual Safety Award Convention and being named winner of the Safety and Health Award Recognition for Projects (SHARP) award at the 2011 Workplace Safety and Health (WSH) Awards. As well, McConnell Dowell won a Green and Gracious Builder Award (Excellent Category) from the Building and Construction Authority (BCA).CITATION:McDonough, R, 2014. Design and construction contract C916 Beauty World Station and Tunnels, Singapore, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 411–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By I M. Platten, Y Xie, B W. Cuffley, S C. Dominy

"Geometallurgical programs require the collection of representative samples for geochemical, mineralogical and metallurgical test work. Such protocols must be designed to suit the style of orebody in question. The distribution, proportion and size of gold particles have a direct impact on the effectiveness of sampling and test work protocols, and the gold recovery processes employed. Characterisation studies focusing on ore mineralogy, and gold particle deportment, size and distribution are required. High resolution X-ray computed tomography provides a non-destructive method for analysing the 3D nature of gold in rock samples. It can be used to calculate the modal abundance, particle size and distribution of gold in the sample volume. This paper presents a case study of the imaging of in situ gold particles in a high-grade gold ore. The Nick O’Time reef system comprises laminated quartz veins, which locally bear extreme grades of up to 100 oz/t gold. The mineralisation has previously been characterised from both a mineralogical and metallurgical perspective. Eight visible gold-bearing vein samples were scanned using X-ray microtomography. Microtomographic data were integrated with previous mineralogical and metallurgical test work outputs.CITATION:Dominy, S C, Platten, I M, Xie, Y, Cuffley, B W and O’Connor, L, 2016. Characterisation of Gold Ore from the Nick O’Time Shoot (Tarnagulla, Australia) Using High Resolution X-ray Computed Tomography, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 241–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By C Harwood, EáWestman, K Luxbacher

Testing of in situ seals in underground coal mines is critical to determine seal integrity and to provide safe working conditions. In the wake of the 2006 Sago Mine explosion, the United States of America (USA) promulgated the Mine Improvement and New Emergency Response (MINER) Act (USDOL, 2006) which required mines to install 827 kPa (120 psi) rated seals or monitor and maintain the atmosphere behind existing 345 kPa (50 psi) seals. The purpose of developing the regulations was to prevent the breaching of seals in the event of an explosion in the sealed area.While seal design and construction is carefully regulated in practice, the construction of seals is difficult to monitor, as many are constructed under various mine conditions and the methods rely on prescribed placement of the seal material. Further examination of installed seals is limited to two-dimensional visual inspection and atmospheric and convergence measuring devices. These methods do not accurately reflect the integrity of the seal and cannot detect changes, deterioration, or defects within the seal.If detection of defects, deterioration and damage is not possible, unexpected communication between the active and sealed areas may result. Additionally, the ability of the seal to withstand explosions may be compromised. Non-destructive testing (NDT) of underground mine seals is necessary to investigate if the seal properties have been altered and if the seal remains functional as a barrier between active areas and sealed areas of the mine. This paper gives a preliminary assessment of proposed NDT methods for seal evaluation using radio frequency (RF) technologies and tracer gas methods.CITATION:Harwood, C, Luxbacher, K and Westman, E, 2013. Non-destructive testing of in situ underground mine seals - Initial technology assessment, in Proceedings The Australian Mine Ventilation Conference , pp 299-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The character of alluvial gold deposits presents severe difficulties, and sometimes limitations, on the extent to which metallurgical efficiency can be measured. Very little monitoring of metallurgical performance is practised. An indication of performance is often extracted from the comparison of production to the estimate. This is a dubious practice. The recovery efficiency of conventional practices, viz sluices, tables and jigs, falls off sharply below 0.2 mm. Field evaluation procedures tend to simulate these conventional practices. Thus the presence of fine gold may not be detected, particularly if obscured by clay. There is increasing evidence that fine gold could, in places, be present in sufficient concentrations to be economic. Most gold in paleoplacers is finer than 0.1 mm. There are established practices elsewhere in the mineral industry that may physically recover gold down to 5 microns in size and which could find application for fine alluvial gold.

Jan 1, 1984

By H Barrie, L Ameglio

"Current methods for acid rock drainage (ARD) mitigation revolve around insulation of the waste from oxygen in the atmosphere with water and dry (soils and liners) covers. Both are of limited effectiveness and present significant drawbacks. Furthermore, while they reduce oxygen influx, they reduce but do not prevent ARD.The inert gas mixture (IGM) technology has been designed to overcome the deficiencies of gas transfer into tailings and waste rock materials across the surface and instead block oxidation by controlling the transfer of oxygen from the atmosphere. Inert gas is injected into the mine waste at low flow rates and the positive but low flow purges the oxygen that tends to diffuse into the sulfide waste across the surface. The positive flow of IGM compensates for inward oxygen diffusion and creates a pressure drop across the cover layer preventing inward diffusion of oxygen and, hence, acid generation.The IGM processes are evaluated in this paper: theoretically, with a review of the theory of ARD and the current state of knowledge about the performance of notably dry covers as atmospheric oxygen barriers via models to predict the performance of the IGM technique practically, with a bench-scaled experiment.The results demonstrate the effectiveness of IGM to prevent oxidation of sulfide minerals and ARD in waste rock. The laboratory experiments further identified key variables to be used to monitor performance and control efficiency of IGM, which is now awaiting field-scale application.The IGM technology is a patented process by Terraquest Technologies Ltd (Canada) in USA, Canada and Australia. The IGM technology can be cost-effectively manufactured on-site with commercially available compressors and gas filtration membranes. It is predicted that low-cost covers can then be utilised with IGM, which in turn lowers the overall capital costs of ARD mitigation.CITATION:Ameglio, L and Barrie, H, 2015. Acid rock drainage prevention using inert gas mixture technology, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By E J. Sellers, A Cocker

Movement of the fragmented rock mass is an inevitable consequence of open cut blasting. Uncontrolled, unaccounted movement from blasting commonly causes ore loss and dilution from waste mixing. Therefore, the prediction of the post-blast location of both ore and waste is vital in grade control and of direct interest to mining geologists. Direct measurement techniques have matured significantly over the past decade, but their use remains expensive and labour intensive. Access and safety issues are further disincentives to regular movement monitoring. What is needed is a combination of direct measurement to establish baselines and reliable predictive modelling.The W H Bryan Mining and Geology Centre of the University of Queensland has pioneered 3D blast movement modelling using ‘physics engines’ to handle in-flight collisions and predict the final resting place of blasted material. Open cut metalliferous mines are a demanding environment for this style of modelling as they can involve complex geometries and variable buffering, which leads to inconsistent confinement. A version of the model designed to deal with these complexities is under development. A well-controlled field trial was needed to validate this new version.A validation trial was completed at a gold mine in South-East Asia. The aim was to increase throughput by increasing the blast powder factor without losing grade through dilution and mixing with waste. Four blocks were blasted to identify the effect of bench height and face confinement on ore movement, fragmentation and process throughput. The powder factor and blast timing were kept constant. Movement of the broken rock was measured by placing blast movement monitors at known positions in the block and then locating them after the blast. The majority of sensors were recovered, providing a unique insight into blast movement dynamics and generating a substantial data set for model validation.The model (called ‘MetaMove ‘) was calibrated for one blast and applied to investigate the extent of grade loss and possible mitigation strategies. Conventional mining techniques that involved firing across the strike of the orebody, and no post-blast boundary adjustment of the ore/waste boundaries prior to digging, were found to cause up to 44 per cent loss of high-grade ore, depending on the grade distributions. Post-blast adjustment of the ore/waste boundaries can negate this loss. The model indicates that altering timing and ensuring that the block boundaries are well confined can further constrain the movement of ore/waste boundaries. Thus, the model can be successfully applied to minimise grade dilution and limit misclassification of ore as waste whilst using higher powder factors to increase mill throughput. Application of a calibrated model to move ore/waste boundaries prior to digging will enable the production geology team to add significant value to the mining operation.CITATION:Cocker, A and Sellers, E J, 2014. Modelling blast movement for grade control at an open cut gold mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 377–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Y L. Ma, M Chen, W Bruckard

With the extensive exploitation and gradual depletion of high-grade copper reserves, the mining industry is paying more and more attention to the hydrometallurgical extraction of copper from lowgrade and arsenic bearing copper ores. Hydrometallurgical processing, such as heap leaching, column leaching and bioleaching, provide a viable alternative to the traditional pyrometallurgy due to its harmony with the environment, moderate capital investment, and low operating costs. However, the slow leaching kinetics of enargite (Cu3AsS4) and chalcopyrite (CuFeS2) remain problematic for commercial leaching practice. The formation mechanism and the nature of the passivating layers during leaching is still a matter of debate in hydrometallurgical research. In this study, the dissolution mechanism of enargite and chalcopyrite in sulfuric acid solution was investigated using a range of electrochemical and spectroscopic analysis methods. Electrochemical oxidation of enargite demonstrated an obvious passivation region from 500 to 750 mV (Ag/AgCl). The formed passivation film was found a n-type semiconductor behaviour, which is different from the original enargite with a p-type behaviour. The results of X-ray photoelectron spectroscopy (XPS) suggested that a nonstoichiometric film Cu(3−x)As(1−y)S4 (x>>y) accumulated on the electrode surface, which accounted for the obvious decrease in current density in the passive potential region. For chalcopyrite, three important potentials of 550, 680 and 730 mV which are related to the formation and dissolution of passivation film were observed based on the cyclic voltammetry (CV) and potentiodynamic polarisation. Raman and X-ray absorption near edge structure (XANES) spectra studies of the chalcopyrite electrodes after being treated under these three potentials indicated a metal-deficient sulfide of Cu1−xFe1−yS2 (y>>x) might be responsible for the passivation phenomenon. Hence, it is concluded that the passivation of enargite and chalcopyrite are similar which are caused by metaldeficient sulfide surfaces although the compositions of the metal-deficient sulfide are different.

Aug 24, 2022

By E Amini, M Scott

Grade Engineering® involves the planning, integration and operation of coarse preconcentration techniques to reject uneconomic material as early as possible in the mining value chain to improve the quality of ore delivered to mineral processing activities. These preconcentration techniques include screening for natural and induced deportment of grade to finer size fractions during blasting and coarse breakage, sensor-based measurements of grade and mechanised sorting at particle or bulk scales and coarse gravity separation. Over the last decade, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE), with the support of its participants, has developed a framework for the holistic evaluation of economic and production impacts attributable to these preconcentration techniques. The framework combines the characterisation of preconcentration responses, geostatistical modelling, process modelling and simulation of downstream and upstream production impacts and the optimisation of strategic mine plans to quantify changes in net present value due to different preconcentration strategies. This framework has been applied to evaluate preconcentration techniques at numerous metalliferous operations and can also be used to quantify changes in the environmental metrics for energy, water and steel consumption and emission, tailings and waste rock production. This paper collates the results of these Grade Engineering® studies to show the range and magnitude of economic and environmental impacts attributable to preconcentration. The studies have shown that rejection of uneconomic material prior to mineral processing activities can have a pronounced improvement in energy, water and comminution steel productivity, emission intensity and the profitability of metalliferous mining.

Nov 10, 2020

By D Kent, D Eisner

A lot of talk has been generated about the so called ‘Internet of Things’ (IoT) and its potential to transform the way we interact with our homes and devices. But the true potential and value of IoT is not going to be realised by the general consumer but by businesses.This paper outlines the application of IoT in mining and how it is a natural extension to the base networks becoming commonplace in both surface and underground mines. The potential for ubiquitous monitoring throughout a mining operation at low capital and support costs will transform the ability to monitor, analyse, report and manage all of the key processes involved in a mining operation.Importantly, the paper will discuss the practical applications that the IoT offers mining and explain how this really is transformative technology, not just the latest buzz words from the information technology (IT) world. If leveraged correctly the impact on mining, its cost base and efficiencies, is enormous.CITATION:Kent, D and Eisner, D, 2015. What the internet of things means to mining, in Proceedings Third International Future Mining Conference, pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By S Thacker, M Noakes

The Newmont Tanami Operations (NTO), formerly the Granites Gold Mine, commenced operation in the mid-1980s with tailings deposition evolving over the past three decades as production has increased and the operation has expanded. Paddock-style tailings storage facilities (TSFs) and in-pit tailings deposition have fulfilled the tailings requirements for NTO over its lifetime with the technical specifications of these facilities improving over time in line with the positive development of standards, guidelines and best practice.This paper reviews the options for tailings storage facilities at NTO and the many considerations that have been analysed and deliberated upon before settling on specific TSF types and designs. It also explains the operating philosophies of the tailings deposition and how the facilities have always strongly maintained the optimum capture and retrieval of water. The current TSF design and criteria is presented, along with the introduction of dry tails harvesting for use in paste production as a backfill product for the underground mine. Tailings deposition and recovery remains a critical function of the Granites process to ensure long-term operation and gold production.CITATION:Thacker, S and Noakes, M, 2015. Newmont Tanami Operations – tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 305–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A Deakin

It has been almost a decade since the release of the International Council of Mining and Metals (ICMM) Health and Safety Critical Control Management: Good Practice Guide (2015a). During this time the ICMM member companies, along with many others across industry, have been busy designing, deploying and enhancing their own critical control management (CCM) programs. So, what have we learnt? This paper discusses the scope, application and learnings from the implementation of CCM within the mining industry. What’s going well? What are the common challenges? What are the opportunities to strengthen the approach? What are the threats to successful implementation? The paper draws on the author’s experience as one of the key contributors to the development of the CCM Good Practice Guide and an adviser to many mining companies, including six of the ICMM members. The paper focuses on the practical (operational) application of CCM and the cycle of identifying, defining, implementing, verifying and improving critical controls at the frontline. The paper also includes a discussion on the safety performance of the ICMM member companies over the past decade and provides a recommendation for how CCM can be incorporated into a more proactive model to measure safety performance. The paper concludes with practical recommendations that mining companies, regardless of their CCM maturity, can consider as they look ahead. They are supplemented by three additional recommendations for consideration at the industry level.

Apr 16, 2024

By J Gotte, C Morley, J Froud

Newcrest Mining LimitedÆs Telfer Mine is a world-class gold and copper producer, situated in the Great Sandy Desert, in the north west of Western Australia. The mine has a number of distinctive characteristics such as being one of AustraliaÆs most remote mine sites, being within 270 km of the hottest town in the southern hemisphere (Marble Bar) and having been shut down and reopened after a two-year feasibility study. The construction of a new plant and reopening of the mine gave Newcrest the opportunity to review their mining practices and systems including the opportunity to incorporate reconciliation as a core process. Telfer is now well on the way to being one of the largest gold and copper concentrate producers in Australia. When the mine reopened in June 2003, Telfer implemented SnowdenÆs Reconcilor software system to facilitate reconciliation of geological models, production data and plant measurements. The system was implemented on site in June 2004, as a web-based information management system, integrating other existing mining and plant software packages. It continues to provide an auditable process and consistency of data, providing ease of analysis with standard and customised reporting. This paper provides a case study of the reconciliation system implementation at Telfer. It outlines the consolidation of a number of management systems into one centralised system that can be used to compare and reconcile the tonnes and grades from the mine through to the mill. The authors outline the key estimates and measures that are used for reconciliation at Telfer, detailing the characteristics of the system used to capture the information and the benefits that have been gained through the use of a rigorous reconciliation process on a complex orebody.

Jan 1, 2007

By J P. van Dyk

A new crude ilmenite beneficiation process was recently proposed that allowed for the preparation of a smelter grade ilmenite from ilmenite with elevated chromium content. Magnetising roasting was not utilised in the process. As part of this circuit an ilmenite low susceptible reject stream was produced that had a low magnetic susceptibility. In this article a magnetising roasting process was investigated to beneficiate this material. Tests were conducted on material produced by pilot scale simulations on a typical South African East Coast heavy mineral reserve. The results obtained were compared to those published in literature for crude ilmenite. The small-scale experiments were used to define approximate operational limits for the oxidising roasting of a low susceptible ilmenite low susceptible reject stream, although industrial roasting conditions may differ significantly from those obtained in laboratory units. In a next phase these results will be confirmed on pilot plant scale.

Jan 1, 2001

By J Visser

Dust mitigation has long been seen as nothing more than managing a nuisance issue, but the reality is that poor dust management can lead to one or more of the following negative consequences: an increased risk of safety incidents, lost revenue, reduced and possibly even lost licence to operate, regulatory intervention, high staff turnover and/or absenteeism and occupational health and safety (OH&S) issues. Dust mitigation and management is not a black art; rather it is a scientifically driven process that can provide an opportunity to increase profits, increase the companyÆs status as an excellent corporate citizen, enhance staff retention and reduce the safety risk profile of the operation.The way to achieve success in dust mitigation and control is to apply the scientific method to each problem that can arise and plague any operation by using current industry best practice. This method of dust problem-solving can be applied to dust issues arising from specific dust sources and locations. The dust sources can include wind impacting on stockpiles, open areas, tailings storage facilities, moving train and truck loads, vehicular traffic on roads, the operation of shovels, front end loaders, draglines and other equipment, as well as ore movement on conveyors.The solutions will come from a combination of deployment of dust collection equipment, dust and moisture monitoring equipment, the appropriate application of water and chemicals, the introduction and maintenance of appropriate barriers and the use of predictive data from local and public weather stations. The paradigm shift required is to view dust mitigation as one aspect of normal operational practice, not a ænice to haveÆ or æunnecessary expenseÆ as most operators currently view it. This attitude is becoming more important as more and more local communities oppose the development of mines. One of the reasons for this local opposition is the inevitable dusty environment that is usually associated with mining.Dust mitigation is not a significant expense if correctly designed and included into the system, either as part of the original design of the operation or as a brownfield installation after the fact. Indeed, there is always a loss of revenue associated with dustiness resulting from ore movement and avoiding this goes a long way to paying for any associated dust mitigating costs.CITATION:Visser, J, 2013. Dust mitigation - changing the paradigm, in Proceedings Iron Ore 2013 , pp 27-38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013