Search Documents

By S C. Barrie

St BarbaraÆs Marvel Loch operations have successfully used longhole open stoping as the primary mining method for a number of years. A transition to Core and Shell mining was implemented in 2009 to recover substantial ore grade resources remaining in sill and rib pillars. The transition to core and shell for the Exhibition lode required continuous waste filling of created voids and thus the removal of the crown pillar at the base of the Exhibition pit by blasting. Access to the top of pillar was denied as the pit was partially rock filled with waste rock from underground development.Beyond the technical challenges of the blasting project, a simple and transparent risk management process was developed to ensure appropriate controls and mitigating strategies were in place to minimise risk to personnel during the pillar removal process.Although failure of the crown pillar was anticipated but with the actual timing unknown, on 25 December 2011 the crown pillar yielded during normal mine operations. Engineered and isolation controls in place at the time were of a sufficiently high standard to ensure limited exposure of the underground workforce and minimal damage to mine infrastructure. Successful risk management through implementation of appropriate controls during the project lifecycle of two years and three months proved to be fundamental to the safe removal of the crown pillar.CITATION:Barrie, S C, 2012. Successful risk management through project life cycle for removal of the crown pillar at the Marvel Loch Underground Mine, in Proceedings International Mine Management 2012, pp 125-134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By M Podreka, P Merry, L van den Berg

Anglo Gold AshantiÆs Sunrise Dam operation is located in Western Australia approximately 55 km south of the town of Laverton. Currently, the mine is producing from both its open pit and underground operations and is planning a significant step change in underground production as the pit phases out. The mine ventilation system is arranged in three independent ventilation districts: Astro, GQ and Cosmo. The future ventilation infrastructure requires significant upgrades to keep up with the increased tonnage. In the short term, increased production is planned for the GQ district as well as for Vogue, which is an extension in the Cosmo ventilation district. In the long term, however, Vogue is likely to become the centre of attention for mining activity.This paper explores several ventilation scenarios which include upgrading the existing fan stations, rentals, establishing a common ventilation backbone, and establishing new upcast infrastructure for GQ to support the short-term production increase. These developments were modelled using ventilation network simulation software to determine airflow distribution and fan operating points for each option. For the GQ area, with its short-term increase in production, each option is evaluated for total owning cost by considering capital and operating costs over a three-year period. For Vogue, which is to become the main focus of mining in the future, a different strategy is followed in analysing the ventilation requirements. Instead of considering different short-term options, a number of staged upgrades are considered to achieve the desired production rates.This paper summarises the planning criteria, airflow requirements, ventilation infrastructure requirements, and economic analysis associated with the conceptual ventilation system design. It highlights how the best short-term ventilation infrastructure upgrades can be selected when considered in isolation but highlights that long-term production planning can have an effect on the decisions made in the short-term.CITATION:van den Berg, L, Podreka, M and Merry, P, 2013. Sunrise Dam short- to long-term ventilation planning, in Proceedings The Australian Mine Ventilation Conference , pp 107-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By P Dowd, R Jeuken, C Xu

In Australian coalmines there are a number of coal quality parameters that are measured by analysing samples from boreholes. The data points are used to generate spatial models of these parameters, typically using inverse distance as an interpolation method. Numerous additional boreholes are drilled which have geophysical logs measured downhole but from which no coal quality samples are taken. Full suites of coal quality analyses are expensive and time consuming to drill and sample. If geophysical proxies for coal quality could be used, this would greatly improve the accuracy of the resource estimation without additional cost.This paper examines two of the most important coal quality parameters – ash and volatile matter – and assesses the results of a number of geostatistical interpolation methods. The aim is to improve the accuracy of the interpolated models. Auxiliary variables from geophysical logs are also trialled to improve the estimation.A multivariate analysis of ash, volatile matter and several auxiliary variables of a selected coal seam was undertaken in a spatial context, using variography. This was used to construct a model of co-regionalisation that relates all of the variables as manifestations of an underlying geological theme.The traditional inverse distance interpolation approach was compared to ordinary kriging, universal kriging, co-kriging, regression kriging and kriging with external drift approaches. The relative merits of the six interpolation methods were compared by removing all points, one at a time and estimating at the thus known location. The mean error and the root mean square error were evaluated as a measure of bias and precision.This paper demonstrates that there is significant opportunity to improve the estimations of coal quality when using kriging with external drift. For example, the results show that when using the depth of a sample as an external drift variable there is a significant improvement in the accuracy of estimation for volatile matter. Furthermore, when using borehole wireline density logs as an auxiliary variable for ash content, there is improvement in the estimation of the in situ ash. The underpinning reasons for this are discussed in the context of the underlying geology and the physical properties of the coal. These findings hold promise for utilising cheaper proxies for coal quality parameters to dramatically improve data density and the quality of estimations.CITATION:Jeuken, R, Xu, C and Dowd, P, 2017. Improving coal quality estimations using geostatistics and auxiliary variables, in Proceedings Tenth International Mining Geology Conference 2017, pp 157–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

Two key elements in the design of a pastefill or high density hackfill system are the preparation of the backfill material and its distribution underground. This paper examines these two areas. Owing to the essentially impervious nature of total mill tailings, preparation of pastefill and high density fill from current tailings involves a physical dewatering process. There are currently three methods available for this process: I. Vacuum or pressure filters. These represent the 'traditional' approach to the preparation of pastefill. 2. Paste production storage mechanism. This is a thickening/storage mechanism developed with the specific objective of producing paste/high density backfills. 3. Fluidization. This system utilises silos fitted with simple dewatering devices and nozzles. Recently developed by CANMET, it provides the simplest and most economical approach. This paper describes and compares the three preparation methods, from a practical and an economic point of view. Once the pastefill/high density fill has been prepared and binder added, the backfill must be distributed underground into the stopes. A fundamental factor in the design of a distribution system is the rheology of the material- No two materials will exhibit the same properties, and a sequence of rheological and related testing is required prior to the completion of the design of the underground distribution system. This paper covers the testwork normally required and discusses the fundamental design parameters of pastefill distribution systems. The final section of this paper summarises the use of pastefill at three mincsin Canada.

Jan 1, 1998

By K W. Mills, N R. P Baczynski, J Mylvaganam, D A. Prado, M F. Lee, I A. de Bruyn

"This paper presents the second part of a study of the assessment of rock stress inputs on the performance of various new mining designs at the Ok Tedi large open pit mine in Papua New Guinea. Over the years, four programs of rock stress measurement have been completed at Ok Tedi, each providing different interpretations of the in situ field stresses. Details of three of these programs and interpretations are provided in the precursor to this paper, entitled ‘Rock Stresses at Ok Tedi, Papua New Guinea’ (Lee et al, 2014).This paper explains how the various stress interpretations were utilised in the modelling of the proposed new open pit and underground mining excavations, comparing where possible their expected effects on stability. The modelled performance of three specific mine components have been discussed here as case studies, including: the below-pit drainage tunnel, as the floor of the open pit workings is mined down from 350?m above, to within just 75?m above the crown of the tunnel the stability of the 1000?m high slope of the proposed West Wall cutback the proposed sublevel open stoping extraction sequence in the Gold Coast orebody beneath the East Wall, for which only the likely ‘worst-case’ stress regime was used to assess sequencing and stability issues.The benefits of scheduling the collection of detailed rock stress measurements and other input data from a range of different sources at various stages of the projects are discussed.Alternative in situ stress models have less stability impact on open pit slopes than on underground mine excavations.CITATION:de Bruyn, I A, Baczynski, N R P, Lee, M F, Mills, K W, Mylvaganam, J, and Prado, D A, 2014. The application of rock stress inputs to stability assessments at Ok Tedi Mine, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 43–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By P Holtham, K Duffy, B, W Valery, E Tabosa, rade

Pre-concentration has potential to significantly improve Mineral Resource efficiency by removing gangue early in the process, before energy intensive and expensive comminution and fine processing. However, there are numerous options for pre-concentration and the performance and benefits of these are very case specific. To determine the best option for a particular deposit and to successfully integrate it into the overall mining and processing operations requires comprehensive evaluation. This needs to consider orebody suitability, technology capability and economic viability. The in-situ variability of a deposit and how it is influenced by mining methods and the liberation size of gangue are key factors which are generally not well understood. Geostatistical methods provide an insight into orebody variability, and the overall selection of any pre-concentration solution must be an integrated approach between geology, mining and processing. Many pre-concentration evaluations investigate the potential of just one option. Technology selection should start wide and may include: selective mining, pre-screening (with or without selective blasting), sorting (bulk and or particle), coarse gravity separation (e.g. jigging, DMS), coarse particle flotation, magnetic separation, etc. The upgrade performance of these processes is very ore specific and should be determined from testing, with detailed multi-component modelling used to determine the overall process performance. Many of these pre-concentration processes require significant ancillary equipment, feed preparation and materials handling. It is important to realistically estimate all costs to understand overall economics and select the best option. Some examples showing evaluation and comparison of pre-concentration options are presented in this paper. These include assessments of in-situ variability using geostatistical tools, process modelling of pre-concentration options and overall performance, preliminary layouts and cost estimates, and economic evaluations.

Nov 10, 2020

By J Franz, S Bock, N Hentrich

Artificial ground freezing is the unrivalled method for groundwater control during mine shaft sinking. Moreover, ground freezing may also provide temporary ground support. The fast development of fibre-optic temperature monitoring devices, three-dimensional freeze pipe survey methods and numerical modelling software provide grounds for developing new and reliable tools for ground control during freeze shaft sinking. This paper presents examples of predictive numerical models that are based on back-analysis and calibration of temperature data that covers the complete construction cycle from pre-freezing through to artificial thawing. The back-analyses showed that standard numerical models are not capable of predicting the prevailing thermo-mechanical conditions satisfactorily. This paper describes the development and implementation of new tools for improved consideration of concrete hydration and latent heat, along with the introduction of other algorithms that improve and simplify the efforts of managing complex numerical models. A function is presented that allows for an automated correction of the model’s mesh based on results of three-dimensional freeze pipe surveys. This paper demonstrates that the latter consideration is important, because the often employed assumption of idealised freeze circle geometry in numerical models impacts on the accuracy of such model’s predictions. Subsequently, the verification of these extended numerical models is demonstrated. Due to its flexibility, the FLAC3DTM code was employed for the numerical modelling. This software provides the possibility of implementing additional functions written in internal FISH or Python language into the models. It is concluded that state-of-the-art techniques for freeze hole drilling and surveying, on-site monitoring and advanced numerical analysis provide a significant potential for both the design and the operation of largescale ground freezing measures. The application of the extended numerical models for predictive simulations during construction allows for temporary shaft lining optimisation, for assisting in operational decision making and for compensating temporary loss of monitoring data. Suggestions are made for required future work in order to further improve the developed ground control tools. CITATION:Bock, S, Franz, J and Hentrich, N, 2018. New tools for ground control in freeze shaft sinking, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 393–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Jackson, D C. Curry, A C. Keith

Australian Bureau of Statistics (ABS) data shows that since 2006 the balance of capital costs associated with mine development has become weighted greater than 75 per cent to enabling infrastructure and less than 25 per cent on process plant, equipment and machinery. The well-developed mine planning techniques including pit optimisation and scheduling and process plant design and optimisation have typically proceeded in a linear fashion from geology, mine planning, through processing, with some iterations back to the mine. Only then is attention paid to planning and costing of enabling infrastructure in any detail.Optimisation has typically involved developing cut-off grades, mine plans and schedules and ore processing that produces maximum economic ore. Infrastructure has then been sized æto suitÆ the mining and processing core business drivers.What the ABS data, together with global trends, indicates is that infrastructure can no longer be an afterthought if miners wish to achieve robust project value estimates, realistic ore to market costing and resource statements based on achievable economic cut-off grades.In addition, with such a large proportion of the costs originating from non-mining or processing activities, a mining operation can only be truly optimal if these aspects are given due consideration in the mine design stages, based on quality geometallurgical inputs so that the size and cost of enabling infrastructure is optimised to maximise project value.This paper outlines an iterative holistic approach to mining project development, which integrates the geometallurgical approach and enables infrastructure planning into project design and evaluation. It presents case studies showing reduced overall costs, increased net present value (NPV) and reduced project delivery timelines.CITATION:Curry, D C, Keith, A C and Jackson, J, 2013. Is a 2.5 per cent success rate good enough? Traditional mine development methods have the tail wagging the dog, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 113-128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

Barrick Gold Granny Smith Mine is currently undergoing conversion from an open cut operation to an underground mine at the Wallaby deposit. The underground project commenced in 2005 with the development of the reserves immediately below the pit and is now currently entering a production ramp-up phase for mining of these two initial surfaces below the pit. With increasing gold prices the owner has been forced to re-evaluate the underground project and has decided to investigate the potential of a deep level mine. This deep level underground mine presents a collection of challenges with the most notable being exploitation of a series of well separated near horizontal lodes ranging in thickness from less than 1 to 20 m. A variety of room and pillar mining methods are employed for extraction with careful consideration to resource recovery and pillar design for long-term stability. Compounding these deep level challenges is a need to accelerate mine level development to maintain the production profile of the mine. This paper describes the challenges, key learnings and outcomes of the studies undertaken to date associated with this project.

Jan 1, 2008

By M Gerards, M Steinberg, T Graham

The quality and quantity of Australia’s secondary deposits, which include tailings streams and tailings dams, are higher than most countries’ primary deposits. In addition, these secondary deposits have already been mined and processed, meaning that the recovery of high-grade product requires low capital and operating costs.The most widely used process for the recovery of these valuable fine and ultra-fine hematite iron particles is the wet high-intensity magnetic separation technique, originally developed by Dr Jones over 55 years ago. Many of the original machines are still working today.The aim of this paper is to demonstrate the capabilities in terms of grade and yield of using sophisticated magnetic separation modules. All results and figures are obtained from test work and design and engineering work with material from the Pilbara. In addition, consideration is given to dewatering of iron ore product and tailings.Two types of tailings have been identified for processing. Firstly, tailings that have already been deposited in a tailings storage facility, and secondly, live tailings streams from an existing wet iron ore beneficiation plant. In both cases, the technical and practical results are shown along with relevant flow sheets and plant layouts. Finally, this paper highlights the total predicted power and water consumption, capital requirements and projected operating expenses.The results show that the operating costs are significantly lower than the mining and processing operations that are required for an equivalent amount of iron ore. The recovery of iron depends on various factors but is within the 30–50 per cent range at an equivalent grade to the mainstream product. Another significant benefit is that the magnetic separation process is water positive, meaning that water is released rather than added in the process.The processing of the Pilbara’s secondary deposits will therefore result in an overall reduction in operating costs, an increase in product yield from a plant, extend the life-of-mine and offer environmental benefits by reducing the tailings footprint and water usage.The quality and quantity of Australia’s secondary iron ore deposits and tailings are such that many other countries would judge these as equivalent to primary deposits. Furthermore, these tailings are already mined, available and liberated to such an extent that the recovery of a valuable product is highly economical in terms of capital expenses and operating expenses.CITATION:Steinberg, M, Graham, T and Gerards, M, 2015. Recovery of iron ore fines and ultrafines from tailings by using wet high-intensity magnetic separation – JONES WHIMS, in Proceedings Iron Ore 2015, pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M Habte

This paper presents a simplified method for the assessment of creep deformations in rock masses containing bands of low strength or soil strength rock. The main impetus for this work was the need to assess the impact of distinct bands of clay and/or low strength rock on the long term deformation behaviour of a rock pillar formed as part of a series of proposed tunnelling works. In particular, the authors were interested in being able to provide criterion which could be used by site personnel to assess the encountered rock conditions against design assumptions.Creep deformation versus time plots are presented for a range of material consistencies. These plots were produced using the hyperbolic creep equation proposed by Mesri et al (1981). This empirically based equation was chosen for its simplicity and practicality. Discussion is included regarding typical input parameter values and the sensitivity of the results to these values is explored. Finally, in the soil strength materials, the secondary consolidation equation is used to check the veracity of the results calculated using the hyperbolic creep equation.

Mar 8, 2011

By G van Niekerk, M Wortley

Screening is a critical part of many mineral processing circuits and keeping the aperture of the screening media within specification is vital to ensure efficient performance of the processing plant. Typical ways of estimating and/or measuring the wear of the screening media vary from very subjective methods (for instance, using the human eye) to manually checking the width of a few of the more severely worn gaps with a measurement device. Subjective methods can be flawed by human error while manual checking can distort the polyurethane or rubber materials that are used in several types of screening media. All of these errors can cause either premature replacement of panels or, even worse, poor screening of the material.Metso Process Technology and Innovation (PTI) and Metso Screening Media Solutions (SMS) have developed an innovative method that measures screen aperture using advanced image processing techniques. Field trials of the device are presented in this paper, which shows the comparison between the different methods of measuring apertures. Case studies demonstrate how the system, when combined with ScreenTrack, MetsoÆs industry leading maintenance system, and screening media, is providing users with the best possible screening solutions.

Sep 26, 2011

By M Medina, J Alexander, R J. Longey

Capricorn Copper Pty Ltd (CCPL) are operating the Capricorn Copper Mine located at Gunpowder, Queensland. As current holder of the environmental authority for the site, CCPL have obligations to rehabilitate areas of the mine that are no longer operational and have the potential to cause/contribute to environmental harm. CCPL sought a voluntary Transitional Environmental Program (TEP) to provide an agreed program of works to cap and rehabilitate the former Mammoth Tailings Storage Facility. The voluntary TEP contained conditions that were required to be met, to reduce the potential for environmental harm from the facility. The former Mammoth Tailings Storage Facility commenced use in the early 1970’s, and is an unlined valley in-fill structure, contemporary in design compared with other such approved structures of the era. The decommissioned Mammoth Tailings Storage Facility, now known as the Old Tailings Storage Facility (Old TSF), has been a legacy source of contamination due to the existing capping not meeting modern cover criterion, and allowing oxidisation and infiltration to the underlying acid forming tailings resulting in Acid and Metalliferous Drainage (AMD) from the facility. A cover design for the Old TSF, and other mine waste storages onsite that required clay capping, had been proposed by previous operators. Under the TEP cover design phase, it was identified that a key constraint was the lack of significant quantities of low permeability clay onsite. The lack of available clay prompted the consideration of alternate lining materials for the Old TSF, with a Bituminous Geomembrane Liner (BGM) being adopted as the preferred alternative. The BGM compared favourably with clay-based materials on seepage analysis, and led to other benefits by eliminating the need for borrowing clay off site, reducing the site’s environmental footprint, and reducing construction time. The BGM cover system on the Old TSF is being monitored with the intent to use this as a case study to confirm expected performance, enabling the cover design to potentially be adopted on the remainder of the site’s mine waste storages that require capping.

Jul 1, 2021

By P K. Wong, D A. F Oliveira, F M. Azad

In situations where foundation piles are located in proximity to existing or future tunnels, it is typical for the tunnel owner to require that sleeving of the piles be carried out to at least the invert of the tunnels to minimise any load transfer to the tunnel lining. In competent rock, this practice may be sometimes unnecessary, thus uneconomical. This paper presents an assessment of the effect of pile loading from one of the multi-storey buildings at Barangaroo South in Sydney on the adjacent future Sydney Metro tunnels. It was originally required by Transport for NSW (TfNSW) that the piles be sleeved below the tunnel invert level; however, the building developer wanted to reduce the pile sleeving depth to achieve a more economical solution due to the large number of load transfer piles being required for the project. To assess this feasibility, a full 3D commercial numerical code, FLAC3D, was used to carry out this complex soil-structure interaction analyses. Based on these assessments, it was demonstrated successfully to the TfNSW that the pile sleeving may be terminated at 2 m above the tunnel invert level. For this arrangement, the investigations found that the loading on the piles should have negligible adverse impact on the tunnel lining design. As a result of such an assessment, the proposed pile sleeving level was approved by TfNSW, thus offering an economical foundation solution for the project.CITATION:Azad, F M, Oliveira, D A F and Wong, P K, 2014. The impact of pile loading on adjacent metro tunnels – Barangaroo South, Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 355–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By P Gomez, R Baumgartner, G Escobar

"The Cerro Corona mine consists of a Cu-Au porphyry deposit located in the Andes of northern Peru. The deposit comprises a typical Cu-Au multiphase porphyry mineralisation that has been overprinted by an epithermal event. This has generated a complex pattern of argillic alteration facies, which was accompanied by a locally structural-controlled Au-Cu mineralisation with the presence of gold and limited Cu sulfides and sulfosalts. These features, along with the porphyry-style mineralisation, produced a multifaceted occurrence of gold.Since the beginning of operations at Cerro Corona in 2008 there has been a continuous improvement of the geological and mineralogical knowledge. All mineralogical studies have mainly focused on host rock types and, to a lesser extent, alteration minerals, but little work has been done on the mineralisation itself. As a consequence, limited mineralogical information was available for use in the process optimisation initiatives.In the last two years, a series of mineralogical characterisation studies were undertaken with two main goals. First, to gain an understanding of the mineralisation genesis and second, to obtain a detailed characterisation of copper and gold minerals to support ongoing process optimisation. The first goal was achieved by conventional optical microscopy while the second required electronic microscopy and other microanalyses due to the necessity of quantifying several minerals of interest for the processing.The results were used to refine pre-existing geometallurgical domains, explain copper and gold losses in the flotation process and to some extent, improve copper and gold recoveries. The mineralogical characterisation is an ongoing work. Mineralogy provides the basis for any optimisation exercise since it looks in detail at the material to be treated and therefore, should be part of all geometallurgical programs.CITATION:Baumgartner, R, Gomez, P and Escobar, G, 2016. Comprehensive Mineralogical Characterisation at the Cerro Corona Cu-Au Porphyry Mine – the Fundamental Key for Geometallurgical Applications, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 221–230 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By T P. Medhurst

In many cases mine design is the most important driver of the profitability of a mining project, however to reach an æoptimumÆ mine plan many compromises have to be made. Some of the fundamental profit (and loss) drivers relate to stoping methods and stope design parameters. Inevitably trade-offs have to be made between the stability of underground openings, ground support costs and production efficiency. This paper looks at the role of geomechanics in the mine planning and design process. The concepts of æcontrollable lossesÆ and æuncontrollable lossesÆ are developed as a means of partitioning ground control costs. A stope design example is given which provides a method of examining mining costs, and includes a decision making element in order to quantify geotechnical impacts and select stope dimensions. The method also provides a general framework as a means of balancing ground control costs against maximising returns from an underground mining project.

Jan 1, 2000

By N S. Weerasekara, S Town, E Lessing, J A. De Torres

Philsaga Mining Corporation (Philsaga) had three main aims in converting their lining system from steel to metal cap. They wanted to increase mill availability, minimise localised high wear and optimise particle breakage to deliver increased efficiency within the milling circuit. Combining Discrete Element Method (DEM) modelling and empirical interpretation of liner wear resulted in a rigorous approach to understanding the impact of mill liners on overall mill performance. This new understanding was subsequently used to not only derive a new lining design to optimise performance and thereby improve overall plant economics, but also to guide further lining development.In this work, detailed DEM modelling, developed from actual plant data, together with optimising liner design for wear paved the way towards the installation of a Metal Cap lining system at Philsaga’s &#216;6100 mm SAG Mill. The results were a reported increase in SAG mill throughput of 16 – 20 per cent due to improved breakage through more efficient use of installed power, a reduction in localised high liner wear with overall increase in liner life and reduction in liner replacement time. Site also reported an increased gold recovery of 2 per cent which the improved breakage might have contributed to. This paper will present the design challenges and compare the Metal Cap lining systems performance against Steel lining system. CITATION:Weerasekara, N S, Lessing, E, Town, S and De Torres, J A, 2018. Metal cap versus steel lining system at Philsaga Mining Corporation’s &#216;6100 mm SAG mill, in Proceedings 14th AusIMM Mill Operators&#39; Conference 2018, pp 653–664 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Euston

In the 1990s round flotation tanks were introduced as a result of the lower fabrication costs for larger cells. It was soon observed that round tanks held a number of further advantages over the traditional rectangular cells, such as better hydrodynamics, lower costs and reduced footprint per unit volume.In the last twenty years flotation cell sizes have increased almost exponentially and designs of 250 to 300m3 are a well established standard with plans for full scale pilot installations of 500m3. The option to install these large cells gives flexibility in circuit arrangements and allows efficient and economic matching of flotation lines with modern mill designs. The benefits of scale up are well known with reduced numbers of cells required, lower power costs per unit volume, etc. These benefits will be briefly reviewed with specific reference to the installation of 300m3 to 350m3 flotation cells at the Copperton Concentrator of Kennecott Copper in Utah, USA.The sophisticated techniques required to model these ‘supercells’ have led to a critical review of the fundamentals of flotation science and engineering. In addition to outlining the advantages of large flotation cells, this paper will review the science which supports, and occasionally challenges, the ongoing trend to larger flotation cells.

Aug 8, 2011