Search Documents

By H F. Yu, S Ueda, J Diao, W F. Gu, Y Sasaki, H Qin

The main reason for the underutilisation of steelmaking slags is their instability, which is influenced by their complex phase structure. Recycling and sustainable steelmaking slag face challenges due to the presence of magnesium oxide (MgO), a crucial component in steelmaking slag. This study investigates the phase evolution of steelmaking slag during the cooling process with different MgO contents, using high-temperature experiments and FactSage™ software, ver 8.1, (by Thermfact/CRCT and GTT-Technologies) thermodynamic equilibrium calculations. X-ray diffraction (XRD) and scanning electron microscope - energy dispersive x-ray spectroscopy (SEM-EDS) analyses identified main phases in steelmaking slag, including Ca2SiO4 (C2S), RO (MgO-FeO solid solution), Ca2Fe2O5 (C2F), and Ca3SiO5 (C3S). The study reveals that RO phase increases as the MgO content increases. C3S precipitates from steelmaking slag with a 12 mass per cent MgO content at a reduced temperature of 1400°C. It is important to note that C3S remains in the steelmaking slag even after slow cooling. This may be due to the substitution of Ca2+ in C3S by Fe2+ and Mg2+ ions. Intriguingly, the precipitation of f-CaO in steelmaking slag with 10 mass per cent of MgO content occurred after one year, while there was no manifestation of f-CaO precipitation in the steelmaking slag with 12 mass per cent of MgO content even after one year. This discrepancy suggests a potential stabilising effect of an appropriate amount of MgO in steelmaking slag. However, it is crucial to emphasise that this inference lacks supporting data, necessitating further research to validate this hypothesis. The significance of this work is in uncovering the complexities of steelmaking slag behaviour, providing essential insights for optimising recycling processes. The research sheds light on the factors that influence the phase composition and stability of steelmaking slag, contributing to the utilisation of steelmaking slags, promoting environmental sustainability, and enhancing the overall efficiency of metallurgical processes in the current industrial landscape.

Jun 19, 2024

By N Yarahmadi

Characterization of pore pressure is critical for appropriate design of tailings dams. Furthermore, if seepage rates through tailing embankments increase unexpectedly or become uncontrolled, undesirable conditions may prevail to progress piping or internal erosion that could lead to the dam’s instability or ultimate failure. A three-dimensional seepage analysis was performed on a tailings dam using finite element method to find the rate of seepage and pore water conditions in the embankment and foundation. The results were then compared to a conventional two-dimensional seepage analysis carried out on the typical cross section of the embankment and the field data acquired from the instrumentation system. Considering the monitoring data, comparison of seepage analyses results for the two and threedimensional models, showed that the results of the conventional two-dimensional seepage analysis are significantly underestimating reality. Relying on two-dimensional seepage analyses might result in underestimation of seepage rates and impact the safe operation of tailings dams. Similarly, unrealistic prediction of pore water pressure conditions, based on simplified seepage analyses, can lead to overestimation of the rate of strength gain of material and consequently safe embankment raising rates.

Jul 1, 2021

The Australian coal industry has undergone sevenfold growth over the last 30 years and since 1985 has been the world's largest coal exporter. Three quarters of Australia's coal production is exported so its future is dependent on it remaining internationally competitive with other energy sources and other coal exporting countries. Coal is likely to increase its share of the energy market during the nine- ties as oil prices increase, new coal-fired capacity is commissioned and some form of nuclear energy is developed which is of acceptable safety standards to the community for use in the 21st century. Gas may take a part of coal's anticipated market share by the Year 2000. While coal exports will increase from China, Colombia, Indonesia and Venezuela and satisfy some of this additional coal demand Australia will also expand its export production, due to its existing advantages. The United States, Canada, South Africa, Poland and USSR seem unlikely to enjoy the same degrees of expansion and some, particularly Poland and USSR, will decline. Australia will always find it difficult to compete in the more distant markets due to levels of ocean freight, although its high quality coals will tend to partly offset such disadvantage.

Jan 1, 1988

Sampling errors result from heterogeneities within the lot under study. Within a rock mass in situ heterogeneity results in the geological nugget effect, which accounts for most of the natural variability. In broken rock, constitution and distribution heterogeneities are important. A major result of the constitution heterogeneity is the Fundamental Sampling Error (FSE) which is the smallest residual error that can be achieved. It cannot be eliminated, but can be minimised and refl ects the fact that the broken rock sampling process is never completely free of error. Together with other sampling errors, FSE contributes to the total nugget effect. The FSE for a sampling protocol can be evaluated using the so-called Gy equation. Its practical applications to low-grade gold ores have often been unsuccessful due to problems linking the FSE and minimum sampling mass and the defi nition of key parameters such as the liberation diameter. Well-designed sample protocols minimise the total sampling error and hence the nugget effect. Reduction of the nugget effect is a key requirement for all sampling programs whether related to exploration and resource evaluation, metallurgical test sampling, grade control or metallurgical plant sampling. This contribution reviews the relationship between heterogeneity, FSE and nugget effect in gold deposits; and emphasises the need for FSE management throughout the mine value chain.

Aug 1, 2010

By D A. Williams, P J. Chapman

The acceptable rate of rise of the tailings beaches on upstream-raised tailings storage facilities (TSFs) is critical to life of mine planning. This is illustrated through a case study in Western Australia presented in this paper. Accurate estimates of expected beach slopes, the maximum rate of rise at which the tailings can be placed, and the dry density that the tailings solids will achieve after deposition (stored density) are required in order to design TSFs that will allow upstream raises to be constructed safely and economically. Where operations have been occurring for some time, these three parameters are able to be measured and can be well-defined. If process plant throughputs are proposed to increase through mine expansion, for example, increasing the rate of rise of the tailings can compromise the potential for upstream TSF raising, thus influencing the viability of such an expansion, the timing for its implementation, and significantly increase costs.This paper outlines how rate of rise can be a key constraint, and that ‘rules of thumb’ that are typically applied may not result in the outcomes they were meant to achieve. An example of an experimental method to justify an increase to the ‘rule of thumb’ ~2.5 m/year limit for gold tailings in a semi-arid climatic setting is discussed, followed by rate of rise modelling that ultimately framed the decision-making process for a mine expansion. The rate of rise modelling method was adopted to carefully distribute tailings deposition across four TSFs, comprising nine separate tailings cells, in order to maintain appropriate rates of rise. The implications resulting from various deposition splits are presented, including the need for expansion. In addition, this paper outlines the effect of rate of rise on the state (density) of the tailings after deposition, and provides commentary on how anecdotally acceptable rates of rise, based on the aforementioned ‘rule of thumb’ of 2.5 m/year may not provide assurance of geotechnical stability through the tailings achieving a dilative state, as has been thought in the past. An example of the influence of rate of rise on the state of the tailings, with respect to air-drying and the critical state line (CSL) for the material, is presented. The data indicate that reducing the rate of rise may allow a higher dry density to be achieved through air-drying (evaporative desiccation), sufficient to move the material from the contractive to the dilative zone (i.e. from above the CSL, to sufficiently below it).CITATION:Chapman, P J and Williams, D A, 2018. The importance of rate of rise in life-of-mine planning of an upstream raised tailings storage facility – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 350–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By S Shafiee, N Abbate

The evaluation of mining projects requires a methodology that will give flexibility and manage the existing uncertainty within the projects. The discount cash flow (DCF) and other traditional evaluation approaches, which are widely used in evaluating a significant number of mining projects, have simply assumed that the main variables remain constant in their evaluation; elements such as discounted rate, mine life, operating cost and production rate. The DCF ignores managementÆs flexibility to adapt and reforecast and revise decisions. Real options valuation (ROV) is one of the modern evaluation methodologies that provide a tool to adapt and revise mining projects under uncertainty and future variables movements. ROV brings more variables into the evaluation model compared to DCF and assumes them as uncertain and dependent. Finally, ROV provides a range of solutions that can assist in managing this flexibility.This paper endeavours to compare ROV and DCF for mining projects comprehensively and applies these two techniques in the model. The paper shows that ROV will be inclusive of extra value in mining projects due to variables not allowed for, or even ignored, when the DCF model alone is used. One of the significant advantages of the ROV method is being able to evaluate mining projects under different scenarios from the inception of the projects. Furthermore, ROV gives the ability to evaluate the mining project while allowing for abandonment, temporary suspension, or expanding the mining project. In other words, the ROV evaluation process creates an analytical environment, which allows for optimisation of the mining plan within the mining project, as well as the ability to change the capital structure dependant on existing circumstances over the life of the project. The ROV is a new evaluation method that can add value in mining project analysis and offers opportunities to amplify gains, or to mitigate losses. This paper also discusses some of the reluctance to use ROV instead of DCF in current project evaluation.CITATION:Shafiee, S and Abbate, N, 2012. Now, this is the time for mining companies to choose - Real option valuation or discount cash flow, in Proceedings Project Evaluation 2012 , pp 225-234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By C Bie, S Li, P Xiao, P Zhao, H Lin

"Based on solid simulation material research, the simulation conditions for methane and coal solid-gas coupling were obtained using solid-fluid coupling theory. Using sand as the aggregate and paraffin and oil as the cementing agents, a material suitable for solid-gas coupling simulation was developed. A permeability testing instrument was also developed, and the compressive strength, brittleness parameters and seepage velocity of material were tested with different aggregates. The results showed that as the paraffin content increased, the compressive strength of the material increased but the permeability decreased. The oil removed the drawback of intensely changing material compressive strength. By setting a different ratio of aggregate to cementing agent, it can simulate rocks with different strengths and permeability. Applying the material to a mining simulation experiment revealed a relationship between methane seepage velocity and overlying strata movement. By extracting pressure relief gas from Shanxi Tianchi coalmine drainage, the authors found that the mining fissure zone was a storage area of pressure relief gas, and a gas drainage system can be placed to achieve good results. CITATION: Li, S, Zhao, P, Lin, H, Bie, C, Pan, H and Xiao, P, 2015. Character of simulation material of coal – rock and gas solid-gas coupling and engineering application, in Proceedings The Australian Mine Ventilation Conference, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By L Mollison, K W. Mills, N R. P Baczynski, M F. Lee, I A. de Bruyn

This is the first of two papers concerned with rock stress inputs to various mine design issues at the large Ok Tedi open pit mine in Papua New Guinea. The companion paper (also published at this conference) is ‘The Application of Rock Stress Inputs to Stability Assessments at Ok Tedi Mine, Papua New Guinea’ (de Bruyn et al, 2014).Stresses are a required input for numerical modelling of mine design issues. However, for some operations, like the very large Ok Tedi open pit mine in remote rugged mountainous terrain, direct and representative measurement of rock stresses can be technically difficult and expensive. In such situations, development of an appropriate and sufficient understanding of rock stresses can be challenging.This was addressed for Ok Tedi by considering the following:The tectonic and regional geologic setting of the mine.Results from three different programs of rock stress measurement over 19 years, including hydraulic fracturing (1991), acoustic emission (2007) and overcoring (2010). Some interesting results of the overcoring work are discussed. It was done in a 4 km long drainage tunnel, which intersected a thick monzodiorite intrusive that has metamorphosed contacts to host contact Ieru Formation siltstones; anomalously low horizontal stresses were measured within the monzodiorite.Compilation of rock stress measurements from other New Guinea mines and prospects, both in Papua New Guinea and Indonesian West Papua.Comparisons between the variable Ok Tedi rock stresses and similar data from other porphyry copper deposits.CITATION:Lee, M F, Baczynski, N R P, Mills, K W, de Bruyn, I A and Mollison, L, 2014. Rock stresses at Ok Tedi, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M R. Dehghan, H Mansouri, A Hakami, M A. Ebrahimi Farsangi, F Faramarzi

Today, it is accepted that rock fragmentation by blasting affects loading and hauling operations, and also directly influences on downstream processes such as crushing and grinding. In this research, the influence of rock fragmentation by blasting on the performance of three mills at Gol-e-Gohar iron ore mine No 1 was studied. Firstly, the fragmentation of conventional blast patterns in iron ore (5 × 6 m) was studied using image analysis and the performances of three mills were monitored. Then, a new blast pattern (4 × 5 m) was designed and nine blasts were carried out using this pattern. Increasing the powder factor form 1650 gr/m3 to 2480 gr/m3 by changing the blast pattern design showed that mill throughputs increase five per cent to 30 per cent for the new pattern.CITATION:Hakami, A, Mansouri, H, Ebrahimi Farsangi, M A, Dehghan, M R and Faramarzi, F, 2015. Study of the effect of blast pattern design on autogenous and semi-autogenous mill throughput at Gol-e-Gohar iron ore mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Z Li, J Pan, D Zhu, W Zhou

In order to enhance the roasting behaviours and metallurgical properties of hematite pellets, which have the problems of high roasting temperature and low compressive strength, a process of producing Brazilian hematite pellets by adding high sulfur magnetite was developed in this paper, and process parameters have been optimised. It is shown that the roasting temperature decreases from 1320¦C to 1200¦C by adding 30 per cent of high sulfur magnetite. New Fe2O3 crystal oxidised from Fe3O4 is more active, which is beneficial to induration of pellet. When the ratio of magnetite increased to 50 per cent, only about 90¦C of the roasting temperature was decreased. Higher ratio of high sulfur magnetite causes more porosity of pellets because of oxidative desulfurisation, which is harmful to the strength of roasted pellets. The reduction disintegration index (RDI), presently RDI+3.15 of product pellets is aggrandised from 87.79 per cent to 99.54 per cent and 97.55 per cent, and the reduction swelling index (RSI) is lowered from 36.25 per cent to 12.50 per cent and 6.25 per cent respectively, by adding 30 per cent and 50 per cent of high sulfur magnetite. The compressive strength of roasted pellets is elevated obviously by adding high sulfur magnetite, which resists the inner stress of pellets during reduction process, so as to enhance the RDI and reduce the RSI of product pellets. In addition, the inner porosity may be filled by the swelling during the reduction process, which can also lower the RSI. The process provides a low power consumption of making hematite pellets that high sulfur magnetite can decrease roasting temperature significantly and improve the metallurgical properties of hematite pellets dramatically.CITATION:Zhu, D, Zhou, W, Pan, J and Li, Z, 2013. Study on improving roasting behaviours and metallurgical properties of Brazilian hematite pellets by adding magnetite with high sulfur content, in Proceedings Iron Ore 2013 , pp 525-530 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By C DahnTr-Lindqvist

The Kiruna mine produced about 19 Mt processed iron ore in 1999 using sublevel caving. General failure in the hangingwall has been widely studied and its mechanism is rather well understood. Failure in the footwall is more recent and not perfectly explained. Plane shear failure and Hoek and BrayÆs circular failure charts were successfully used to match the first surveyed failure surfaces. The footwall is not free yet but covered by a caved waste rock abutment whose exact behaviour is poorly known. Based on new field data and numerical models (FLAC), the following paper presents recent improvements in understanding the Kiruna mineÆs footwall failure process.

Jan 1, 2000

By L Ventura, M Almond

The Pueblo Viejo project in the Dominican Republic installed an innovative sample system on its reverse circulation (RC) drilling rig during commissioning and subsequent commencement of operations. As knowledge of the orebody increased with mining and plant production, cost pressures became apparent that raised questions concerning the continued use of RC drilling versus blasthole sampling for ore control.To justify the continued use of RC drilling for grade control, an in-depth study was undertaken to determine the quality of the sample and prove its value-add to the operation.To investigate the differences in sample quality, a complete bench trial was initiated across both ore pits to compare RC drill results with blasthole assays on a side-by-side basis. The results indicated that based on ore block comparison between RC and blasthole sampling, RC identified an additional 20 per cent of high-grade (+ 4.5 g/t Au) ounces.Previous work indicated that Au, Ag and Cu were all elevated in the drill fines at Pueblo Viejo (Goers and Almond, 2012). This previous test work did not consider the quantity of fines in an RC sample therefore new test work was undertaken to include particle size distribution analyses. This study would determine if the inclusion of fines in the sample was occurring and compare the quantity of fines in the sample against other sample systems and blasthole samples.Comparisons between RC samples and blasthole samples indicate that for the RC samples a range of 30–35 per cent of the sample passed 300 mesh as compared to blastholes where the range of the sample passing 300 mesh was 15–30 per cent.This paper includes a case study on the importance of accurate samples and how they have impacted throughput through the pressure oxidation process plant at Pueblo Viejo. The accurate samples provided by RC allow for improved stockpile and blending strategies, showing the importance of accurate samples to manage risk and create value, against the perception that savings can be made at the risk of poor sampling performance.CITATION:Almond, M and Ventura, L, 2017. Adding value with reverse circulation drilling at Pueblo Viejo, in Proceedings Tenth International Mining Geology Conference 2017, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Moylan T, Stewart D

A case study examining the procedures and financial benefits of introducing dump leaching to augment the Mt Gibson Gold Project CIP operations is discussed. Metallurgical testwork, followed by pilot dump leach operations, confirmed that gold recoveries of greater than 60 per cent could be achieved by dump leaching Mt Gibson laterite ore. Capital and operating costs were determined. Pit optimisation using the Whittle FOUR-D optimisation program calculated an optimum cutover grade between CIP and dump leaching for one orebody. The resultant recalculation of reserves based on CIP and dump leach operating costs showed that reserves for that orebody could be increased from 329 000 tonnes at 1.9 g/t An, to 1 488 000 tonnes at 1.2 gh An. NPV for the CIP only option of $1.4 m, was increased to $4.0 m for the combined CIP/dump leach option. This technique can be applied to existing gold projects and to new Developments.

Jan 1, 1992

By D Flint, O Rindriatmoko

PT FreeportÆs Deep Ore Zone (DOZ) Mine is the latest block cave mine within the East Ertsberg Skarn System (EESS).Issues with undercutting and stress concentrations at the extraction level were experienced, leading to reduced pillar strength.The extraction level-related issues became more pronounced, leading to local panel drift collapse, in an area that was over 100 per cent extraction. A review of ground conditions, panel collapse descriptions, and factors contributing to panel collapse are presented in this paper.

Jan 1, 2005

By Morrison AL

The volume changes occurring during the reduction by hydrogen of single, high-grade hematite pellets under isothermal and non- isothermal conditions were investigated using a time-lapse photographic technique. The major cause of swelling during iso- thermal reduction at temperatures in the range 600-1000¦C, was the disruptive stresses set up during the transformation of hematite to mag- netite. The severity of the disruption was temperature dependent; the degree of swelling increased with increases in the reduction temp erature. Under non-isothermal reduction conditions, in which the pellet temperatures were increased at constant heating rates over the temperature range 500-1000¦C, minor swelling (6-8%) occurred in the initial stages of reduction followed by pellet contractions of up to 15% in the final reduction stages. The low initial swelling and high final pellet shrinkages were due to a com- bination of the temperature dependence of the swelling mechanism, and the sintering of fine pores in the reduced iron in the latter stages of reduction at higher temperatures.

Jan 1, 1980

By N McKenzie, E Taylor, S V. L Barrett, H Lagger, A Purwodihardjo

This paper discusses the temporary support design methodology for the largest road caverns ever built in Australia—the Lutwyche Caverns—part of the Airport Link project in Brisbane, Australia. The Lutwyche Caverns with a maximum excavated span of 27 m form a key component of this major road project, allowing on and off ramps merging with the underground highway. In addition to the two large span caverns, a 15 m soft ground tunnel with 5 m cover above the caverns and two 24 m deep burial chambers for the 12.4 m tunnel boring machines (TBMs) had to be built in record time at Lutwyche.The temporary support design methodology involved the use of a range of analytical approaches, including empirical methods to provide a starting point for design development, key block models to determine the potential influence of discontinuities on excavation stability and 2/3D continuum and discontinuum models to determine the potential influence of adjacent excavations and the proposed construction staging on the design. In addition, probabilistic analysis of potential kinematic instability using a discrete fracture network (DFN) approach was also undertaken to establish the critical block loads for the temporary lining, while the continuum and discontinuum models were used to design the support for the 1.5 m diameter rock pillar at the north end of the northbound cavern.The numerical modelling was undertaken in close conjunction with the contractor to develop the optimal construction sequence, considering the available construction equipment on-site and the overall project program requirements. Part of the presentation will further show the applicability of the developed design during construction (deformations, monitoring field observations) and lessons learned for future cavern construction in Australia.CITATION:Lagger, H, Purwodihardjo, A, Barrett, S V L, McKenzie, N and Taylor, E, 2014. Temporary support design for the largest road caverns ever built in Australia – the Lutwyche Caverns, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G Lumley

PlannersÆ optimism (or maybe commercial necessity) means that most mine plans use equipment rates that are rarely achieved (Lumley and Beckman, 2009). This lack of understanding of what equipment actually moves is causing erroneous equipment forecasts, leading to incorrect mine development plans and economic evaluations. Compounding this problem is a downward trend in actual equipment performance in some areas. Consequently, the presentation of realistic mine plans that are actually achieved in practice is not a common occurrence. However, rational, fact-based mine planning is available to those who want it. Hundreds of millions of cycles of data from open cut mining equipment has been collected from mines around the world since 1992. This unique and highly valuable databank is growing at an exponential rate and is being used by a number of our big miners to support rational and fact-based decision-making. However, neither the use nor the appreciation of the value of this data is universal. There is a challenge to everyone in the mining industry - how do you access value from it? The databank was drilled into and the results analysed for, the Australasian Mining and Metallurgical Operating Practices (AMMOP) publication (Lumley, in press). For this paper the analysis has been extended to include interpretation of trends for draglines, shovels, excavators and trucks. It investigates trends between coal and non-coal mines and across geographic areas. It is known that mining equipment performance in most sections of the industry is falling. This paper attempts to quantify the fall and provide explanations. The trends are analysed to extract the reasons behind the changes and most importantly, what can be done about it.CITATION:Lumley, G, 2012. Understanding trends in performance of open cut mining equipment, in Proceedings Project Evaluation 2012 , pp 203-224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Reichman J. P

Extensive use is made of a small scale computer (IBM 1130), in the calculations of ore reserves for Western Mining Corporation's nickel mine at Kambalda, W.A. All surface drilling data such as assays, density and location information, are stored on disk files at the Company's Technical Computing Centre at Perth, W.A. The computer is used to search through the data, select significant ore intersections, calculate the area of influence of each intersection and perform the necessary calculations to arrive at an estimate of the ore reserve. Comparing the computer-assisted ore reserve calculation with an entirely manual operation, it is estimated that a saving of 40 percent in time is achieved together with

Jan 1, 1973

By D Tucker, K Harney

Hatch forecasts that an increasing share of seaborne traded iron ore will be ultrafine, being either concentrate or pellet feed. This provides several challenges for the iron and steel industries, but the principal concern is: how much ultrafine iron ore can be consumed on sinter strands and with a minimal effect on productivity?This paper will identify new supply by project through 2020. Demand will be estimated for sinter production and practical steps will be identified to increase ultrafine consumption in sinter strands. The long-term iron ore price will be forecast to balance supply and demand. The paper will conclude by assessing how the pricing of ultrafine ore will develop relative to the Chinese iron ore indices.CITATION:Tucker, D and Harney, K, 2015. Iron ore ultrafines challenges and opportunities, in Proceedings Iron Ore 2015, pp 501–504 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Robinson, A Turner, R Dale, C Butler

"Sandfire Resources NL- (‘Sandfire’) DeGrussa definitive feasibility study (DFS) identified geometallurgy as a major factor in achieving optimum plant performance at the DeGrussa mine. A geometallurgical initiative was created to proactively investigate this issue, and a key initial achievement was the 2013 paper by Condon et al (2013) on developing a working geometallurgical model from first principles. Significant advancements in Sandfire’s geometallurgical understanding since that publication now shape how information is presented and communicated.The main geometallurgical parameters so far identified as critical factors affecting plant performance are Cu:S ratio, iron sulfide mineralogy, talc carbonate content and sphalerite content. Apart from specific mill strategies, geometallurgical issues have been managed through communication between departments and strategic run-of-mine (ROM) pad management.This paper uses the current theories of geological evolution of the volcanogenic massive sulfide (VMS) deposit at DeGrussa, to discuss the variability between the orebodies C1, DeGrussa (sea floor mounds) and C4, C5 (sub-sea floor replacement) to highlight the different issues each orebody is expected to encounter when processing.A zone of altered low-grade mineralisation surrounds the main orebodies at DeGrussa, referred to as a halo. Talc minerals are often patchy within this halo and often cause significant recovery issues during processing. This halo has been successfully modelled using MgO as a proxy. The ability to model the talc material assists with both identifying potentially problematic zones for processing and geological interpretation of the ore deposits evolution.Early in geometallurgy studies at DeGrussa it became apparent that it would be useful to identify processing performance prior to mining. This necessitated the incorporation of specific sulfide species into the mining block model. These attributes are interpolated from the logged sulfide estimates allowing a clear picture of the abundance of each mineral type within a defined area.In conjunction with the block model a geometallurgical factor (GMF) graph was developed, identifying sulfide mineralogy based upon mineral assays. These two recent additions to the model provide a clear picture of the nature of the ore sources that will be presented to the processing plant.The future of geometallurgy at DeGrussa will see these tools used to aid mine scheduling with a view to further improve processing recoveries.CITATION:Butler, C, Dale, R, Robinson, S and Turner, A, 2016. Geometallurgy – Bridging the Gap between Mine and Mill: a Case Study of the DeGrussa Geometallurgy Program, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016