Search Documents

By S G. Keyte

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.l mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass Yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80 per cent and mass yields of less than one per cent can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

By R J. Worland, D Bowyer, J L. Mauk

The TerraSpec is a compact field portable mineral analyser that uses non-destructive reflectance spectroscopy for mineral identification. The instrument uses and measures infrared and visible light that is absorbed by certain covalent and molecular bonds (AlOH, FeOH, MgOH, CO32-, OH, H2O and NH4) within the lattice of a mineral at specific wavelengths producing an absorption spectral profile. A variety of minerals can be detected including clays, micas, carbonates, and hydroxides as well as some sulfates and silicates. However, not all minerals are detectable, such as quartz and feldspar. Alteration minerals replacing volcanic rocks have been studied for several epithermal prospects in the lower Waitekauri Valley (Sovereign, Jubilee, Scotia and Jasper Creek) and a geothermal field in the Taupo Volcanic Zone. At the Sovereign, Jubilee, Scotia and Jasper Creek prospects previous XRD investigations determined well developed clay mineral zonation with illite in the west (Sovereign and Jubilee) grading into interstratified illite-smectite (Scotia) and smectite (Jasper Creek) to the east. Although the percent of illite within interstratified illite-smectite could not be determined and some illite-rich illite-smectite (>90 per cent illite) and some smectite-rich illite-smectite (>90 per cent smectite) could be misidentified as illite or smectite respectively, the TerraSpec survey determined the same zonation of illite to illite-smectite and smectite. Common chlorite, rare calcite and local kaolinite were also detected. At the geothermal field, the TerraSpec was primarily used to determine the occurrence of kaolinite, dickite and alunite, which form in acid conditions. Widely spaced (every 50 to 100 m) XRD results are in excellent agreement with closely spaced (every 5 to 10 m) TerraSpec results that further determined the occurrence of these minerals in previously unrecognised intervals. It also determined the occurrence of zoned smectite, illite-smectite, illite, and chlorite alteration. Overall, the TerraSpec is a rapid mineral identification technique that is very useful in delineating the occurrence and distribution of certain minerals in both epithermal deposits and geothermal fields. Although the TerraSpec cannot detect as many minerals as XRD, the TerraSpec allows data collection at a sampling scale and speed (real time) that is not practical by XRD.

Jan 1, 2006

By H Hutchinson

Froth flotation is applied to mineral sand concentrates in order to produce commercially viable xenotime concentrates. Experiments indicate that a xenotime product containing 38% Y2O3 at 47% recovery or 34% Y2O3 at 83% recovery can be obtained from a 27% Y2O3 feed. The process involves a primary stage of reverse flotation at which oxide and silicate gangue is floated, and secondary stage of direct flotation at which xenotime is floated. Of the various collectors screened an amphoteric compound was found to be effective at both stages. This was made possible by the addition of sodium silicate at the second stage, which acted as depressant for the remainder of the gangue. Similar studies on a low grade feed material were somewhat unsatisfactory as the grade achieved fell short of what was targeted.

Jan 1, 1990

On Kinetic Coupling in Meso-Scale Phenomena in Mineral Froth Flotation

Sep 13, 2010

A New Technology of Applying SLon-2500 Magnetic Separator to Recover Iron Concentrate from Abandoned Tails

Sep 13, 2010

Extraction and Characterisation of Extracellular Polymeric Substances from the Mineral Surface During Bioleaching of Chalcopyrite Concentrate A mixed culture of moderately thermophilic microorganisms was used to bioleach chalcopyrite concentrate in a stirred tank reactor. The results show that up to 84.7 per cent of copper extraction could be achieved in 24 days at a pulp density of 6 per cent. The leaching rate of chalcopyrite concentrate tended to increase with an increase of dissolved total iron concentration. Furthermore, the extracellular polymeric substance (EPS) on the surface of the chalcopyrite concentrate was extracted and analysed. EPS was extracted at the first, third, eighth, 16th and 24th day during bioleaching, which mainly consisted of proteins, lipids, sugars and ferric irons. After the eighth day the total amount of EPS remained relatively constant. However, the amount of ferric iron in the EPS decreased in a large scale. The ore residue analysis indicates that the decrease of ferric iron was mainly due to the formation of jarosite on the mineral surface.

Sep 13, 2010

Bubble Load Measurements in Flotation - A Critical Review of Current Practice

Sep 13, 2010

By W Valery, S Morrell

In the mining industry blasts are usually designed to fracture the in situ rock mass and prepare it for excavation and subsequent transport. The run of mine (ROM) fragmentation is considered good when it is fine enough and loose enough to ensure efficient digging and loading operations. Mining optimisation strategy is hence usually focussed on minimising total mining costs and maintaining these ROM fragmentation characteristics. Although this approach ensures an efficient mining operation it ignores the potential impact on crushing and grinding. Investigations by several researchers have shown that designing blasts to produce ROM fragmentation to optimise crushing and grinding performance enhances the overall efficiency and profitability (Eloranta, 1995; Kojovic et al, 1995; Bulow et al, 1998; Kanchibotla et al, 1998; Scott et al, 1998; Simkus and Dance, 1998). Field experimentation in this area is often found to be difficult because of high implementation costs and insufficient understanding about the effect of fragmentation at different stages in a comminution circuit. Modelling and simulation of blasting and comminution processes provide a more economic alternative to explore the impact of blast design changes on the down stream operations (Kanchibotla et al, 1998; Kojovic et al, 1998; Adam and Siddall, 1998; Bulow et al, 1998). However, the reliability of such simulations depends on:the ability of the models to reproduce the physical processes that take place; characterisation of rock mass in terms of its blastability and comminution characteristics; and in the case of blast modelling the ability to predict fines (-10 mm) has been found to be particularly important as this fraction has a significant effect on mill throughput.

Jan 1, 1999

Copper Recovery from Printed Circuit Board by Carbonisation

Sep 13, 2010

By M P. Cipold, J F. Bachmann, C C. Bachmann, J Ha

Knowledge of fuel qualities is of ultimate importance for the efficiency of chemical plants or power stations. Although most blending yards are equipped with automatic samplers and the derived samples are processed in the laboratory, the quality variation of the blended product may still be strong. This is caused by several reasons. First of all the process of sampling, crushing, dividing and analysis is time consuming. Results are available only with a delay of two to 24 hours. During this time blending is operated without knowledge of the main parameters. Conveyors with high throughput require expensive sampling systems capable of handling samples which are representative. The frequency of sampling needs also to be high in order to be representative. This results in high maintenance costs and also downtime of the sampling system.Online analysis of bulk materials has matured over time and today it can supplement but not replace laboratory analysis. As an example, J&C Bachmann has realised a coal quality monitoring system on the coal supply of a South African coal processing plant. The plant consumes ~42 Mt of coal per annum. The blending yard consists of two sets of three heaps where coal of six different mines is blended according to the factory’s requirement. From there, the blended coal is fed to the factory on two different belts.In 2010 the plant installed a TEXAS X-ray fluorescence analyser as a trial. It was tested under different conditions on several belts before the customer decided to install six TEXAS analysers on the feed belts to the stackers and two more analysers on the reclaimer belts. All analysers are installed directly on the belt and not on a substream.During the test period blending strategies were developed in close cooperation between the customer and J&C Bachmann. The use of the analysers in conjunction with the blending model has proven that the variation of the reclaimed coal quality was decreased significantly, which results in increased process performance and significant cost savings.CITATION:Bachmann, C C, Bachmann, J F, Cipold, M P and Ha, J, 2017. Online quality control of a coal blending yard, in Proceedings Eighth World Conference on Sampling and Blending , pp 125–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Lean Iron Ore Beneficiation in India

Sep 13, 2010

Strategic planning in mining is an important value accretive process. One of the most important aspects during the planning phase is determining the correct mine and plant design. The traditional mine site design (mine, plant, stockpiles, dumps) develops a fixed system for one set of conditions or expected values. A robust design is a fixed system that is designed to deal with a large range of conditions without changing the system design. A flexible design changes the system dynamically in response to changes in uncertainties. It is hypothesised that a robust design generates less value than a flexible design as it fails to realise the value of actively managing the operation. One of the most critical aspects in creating strategic value from a project is embedded in the design of the system. A flexible design has components that allow the design of the system to change over time. An operational plan is proposed as a hybrid of a robust and flexible design. This paper seeks to compare these different design methodologies. An analysis of the same case study is undertaken to compare these approaches, showing an a traditional net present value (NPV) of $1678 M, robust design NPV of $1787 M and an operational plan NPV of $1867 M - an increase of $170 M.

Dec 6, 2010

By K Niyomjinda, B Etschmann

Chatree Gold Mine is currently the only modern day gold mine operating in Thailand, and is situated approximately equidistant from Chiang Mai in the north and Bangkok in the south. Environmental guidelines set by the Thai authorities require Chatree Gold Mine to achieve a Total Cyanide level of 20 ppm or less in the process plant discharge slurry stream prior to release into the tailings storage facility. This paper describes both the initial difficulties faced in achieving compliance on this limit utilising the conventional INCO SO2/Air cyanide destruction system and the subsequent process improvements initiated to both the leaching process and the standard INCO process to achieve the current compliance levels of approximately 99/100 shifts. Improvements were focussed on the dual aspects of reducing the formation of WAD cyanide and ferrocyanide species in the leaching circuit coupled with process changes to improve removal of the ferrocyanide species from solution during the cyanide reduction stage.

Jan 1, 2004

By D Craw, C Smith, C Rufaut

Oceana Gold (NZ) LtdÆs, Macraes Gold Operation currently has two tailings impoundments, the larger of which covers approximately 75 ha. When an impoundment is temporarily out of use, the surface dries and dust can be blown from the surface to the surrounding area. At present water spraying is used to stabilise the surface, but this is not ideal as Macraes mine can experience water shortages during the summer. This paper examines an alternative method of surface stabilisation using vegetation as a ground cover. The tailings have a low natural fertility, so it is important to determine what will actually grow in the tailings, and whether amendments are necessary. Also important is the effect of the amendments on arsenic mobility in the tailings as the schist rock at Macraes has naturally elevated levels of arsenic. Three plants species, rye corn, barley, and lupin, were grown in metre-deep lysimeters at Macraes mine site. The plants were grown in unaltered tailings, and tailings with one of two amendments added: Bioboost (an organic fertiliser containing biosolids), and superphosphate fertiliser. The leachate from each lysimeter was collected and analysed monthly to determine the extent of arsenic mobility. In addition, laboratory experiments were set up to determine arsenic mobility in tailings with amendments at the centimetre scale.   All plants grew best with the fertiliser amendment, with rye corn growing the best overall. Plants growing in unaltered tailings either barely survived (rye corn, barley) or died (lupin). Plants in the Bioboost amended tailings grew only slightly better than in the unamended tailings. Laboratory experiments indicate that the addition of phosphate fertiliser greatly increases arsenic leaching at the centimetre scale when compared to unamended tailings. The addition of Bioboost only marginally increases arsenic leaching, compared to unamended tailings. This trend has not been repeated in the lysimeter trials on the metre scale over four months. Current results suggest that of the plant types trialed and amendments used, rye corn with superphosphate is the most practical short-term tailings stabilisation method at Macraes.

Jan 1, 2004

By G S. Lane, G D. Richmond, J Dioses

This paper discusses the methods used in the design of flotation plants, including benchscale batch and locked cycle tests and pilot plant trials. Two case studies are presented, one for the Cadia Hill Gold Mine and the other for the Hellyer copper, zinc and lead plant. These case studies present different problems with widely different target grind sizes, liberation characteristics and HellyerÆs sequential flotation circuit versus CadiaÆs æsimpleÆ copper/gold flotation circuit. They have a common theme in that pyrite forms the principal floatable concentrate diluent. Hellyer ore contains finely disseminated chalcopyrite, sphalerite, galena, and tetrahedrite. The flotation plant design was based on extensive benchscale testwork (including locked cycle tests) on drill core and many months of operation of a 30 tonne per hour æpilot plantÆ, using the old Cleveland Tin Mine process plant suitably modified for the duty. The Cadia concentrator was designed on an extensive benchscale variability testwork program, approximately a dozen locked cycle tests conducted on drill core and two weeks of continuous pilot plant trials on three separate samples obtained from an adit into the orebody. The orebody is a monzonite porphyry with disseminated chalcopyrite/bornite/pyrite of very low grade (0.17 per cent Cu, 0.73 g/t Au). Methods used to establish the appropriate flotation circuits for the treatment of the Hellyer and Cadia ores, as well as the interpretation of the testwork data, are discussed in this paper. Plant performance is reviewed in the context of predicted versus operational performance.

Jan 1, 2002

By G J. Lyman, F S. Bourgeois

As the prices of metals slide, financial control of mineral processing operations becomes more and more important. Control of a mineral processing operation implies measurement of grades, recoveries and losses, with every effort being made to recover more product from the same feed. Shareholders become more concerned with the transparency of the operations and the corporate governance.There is only one way to achieve this and this is by sampling and making good use of the results of that sampling. Sampling systems that provide only 'rough' figures are not good enough. Similarly, a competitive position in the marketplace demands close control of product quality. Maximisation of product output demands that the product just meet the specification so that product yield is maximised. Decisions based on precise sampling results carry less risk that those based on imprecise results.This paper reports some recent advances in sampling theory that permit full quantification of sampling distributions, not just the sampling variance as has been possible in the past. These advances can be used together with simulation methods to tie down sampling precisions and develop calculations that quantify decision making risk when using the sampling results. A number of examples illustrate the use of the new advances and a final example indicates the development of risk analysis curves in the coupling of sampling precision to sale of a commodity.CITATION:Lyman, G J and Bourgeois, F S, 2015. Sampling, corporate governance and risk analysis, in Proceedings MetPlant 2015, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

The geological features of the destructive plate margins of the southwest Pacific favour the formation of porphyry type deposits. The major controlling factor favouring the formation of gold-rich deposits of this type is a dense crust. This results in shallow intrusion of large magma bodies beneath andesite stratovolcanoes. Where the intrusives have near vertical sides, the comparatively low temperature of transfer of volatiles from the solidifying melt favours the partitioning of gold into bubbles of volatiles. They reduce the viscosity and density of the melt, resulting in the upward movement of a mineralised melt. With the drop of pressure with upward movement the bubbles separate into a two phase mixture, triggering freezing of the mineralised melt and the formation of a gold mineralised stockwork.

Jan 1, 1995

By J L. Mauk

The Favona low-sulfidation epithermal deposit in the Hauraki Goldfield is less than one kilometre southeast of the world-class Waihi deposit. The veins are hosted by Miocene andesite of the Waipupu Formation, have a total strike length of over 900 m, a vertical extent of at least 350 m and are on average 1-3 m wide. Individual veins have been traced for 200 m with vein widths up to 25 m. The dominant vein textures are massive, crustiform and colloform banded veins and vein breccias, with subsidiary textures including comb, zonal, flamboyant, lattice-bladed, ghost-bladed, microbotryoidal, feathery, ripple and dune, and mosaic. Quartz is the dominant gangue mineral in the veins at Favona. Accessory gangue minerals include pyrite, chlorite, adularia, illite, calcite, and apatite. Electrum is the only gold-bearing mineral and is associated with acanthite, tetrahedrite, pyrite, sphalerite, chalcopyrite, and rare galena. Whole rock geochemical analyses indicate that gold grades correlate with textures/vein types. The highest gold and silver grades are associated with vein breccias and banded veins, with the former containing 28 g/t Au and 136 g/t Ag on average. To date, veins with significant base metal sulfide minerals, and massive and crystalline quartz veins lack significant precious metals (Au and Ag), except for one banded base metal sulfide-rich vein at Favona. An overall zonation of the veins exists, with base metal sulfide minerals dominant at depth (1050 m RL) of the system are characterised by massive quartz veins.Fluid inclusions from a total of 31 quartz, amethyst, and platy calcite veins reveal homogenisation temperatures of ~190-250¦C, with final ice melting temperatures between 0.0 and -0.8. Ice melting temperatures correspond to apparent salinities of 18O value of the water that formed these veins is approximately -4.3 per mil, which is similar to meteoric water-dominated, near neutral chloride fluids in geothermal systems in the Taupo Volcanic Zone.

Jan 1, 2002

The Dynamics and Thermodynamics of Absorbing Lithium of Ion Sieve Preparing Pollymetallic Nodules

Sep 13, 2010

By A F. Cooper

Otago Schist in the Mount Patriarch, High Burn and Cameron Creek areas of northwest Otago grades from textural grade IIA in the east to textural grade III in the west. The entire region is of the actinolite-pumpellyite metamorphic facies. Lithologies in the area are interbedded turbidite sequences comprising pelite and psammite together with pebble conglomerate, greenschist and metachert horizons. The mineral assemblage of the schist is typically quartz-albite-epidote-actinolite-pumpellyite-chlorite-stilpnomelane-calcite. A good foliation is well defined in the area and is predominantly parallel to bedding, except in hinges of mesoscopic isoclinal folds. The structure of the area appears to be defined by a large southwest plunging isoclinal fold defined by bedding with a steeply dipping axial planar foliation. Kink folding and dextral strike-slip faulting in the area postdates the ductile phase of deformation. Pods of rhodonite, rhodochrosite, spessartine garnet, coombsite, caryopilite, Mnstilpnomelane and Ni-Cu-Zn sulphides were found in concordant metachert layers in the Mount Patriarch area. Metachert was also found in float in the Cameron Creek area. Malachite occurrences relating to copper mineralisation were also noted in a green metachert horizon on the eastern flank of Mount Patriarch. The coombsite, in only the third observation worldwide, is the most Fe-rich variety reported.

Jan 1, 2003