Search Documents

By M Lentz

This paper will discuss the issues associated with blasting in an urban mining environment that have been addressed by Winstone Aggregates at the Mt Wellington Quarry. These issues include - control of vibration and air overpressure, repeatability of shot performance, fragmentation on an extremely low maximum instantaneous charge, compliance with Territorial Authority regulations and perception. Over the last two years, in order to address these issues, Winstone Aggregates have undertaken a programme of continuous improvement, which has included; ò implementation of new technology; ò revising site procedures; ò conducting an investigation into the structural response of local buildings; ò investigating safe extrapolation; ò extensive public consultation; ò establishing credibility during the consent process; ò identification of perception issues; and ò building relationships and trust with neighbours. The issues addressed at the Mt Wellington Quarry have increasing significance for traditionally rural mining operations, as the input of the local community being urban or rural, increases. New and existing operations have the potential to adopt best practice now, building trust with the community and raising the profile of the industry.  

Jan 1, 1999

By A Kurniawan, A Sjadat and M Akhasyah

PT Freeport Indonesia’s Deep Ore Zone (DOZ) is a block cave mining operation that has been in production for 15 years. DOZ is located approximately 900 m below surface and has an average production rate of more than 5000 t/d. The footprint of the extraction level will ultimately be 900 m long and average more than 200 m wide. The undercut level is located 20 m above the extraction level.While developing Panel 1K on the northern portion of the extraction level, a major geotechnical problem was encountered when there was a change in lithology and an associated fault intersection. A large collapse of the hanging wall of the extraction level drifts occurred in the area of the fault intersection between February and March 2011. This was followed by a collapse of one of the undercut level drifts directly above the extraction level in May 2011.It was suggested that the best approach to mitigate risk during rehabilitation was to systematically open up the failed area under the protection of a steel set support system. To achieve this, approximately 60 t of grout was injected from the undercut level to fill the voids created when the rock mass between the two levels failed. A ground penetrating radar system was used to survey the condition of the rock mass between the two levels before and after the injection of grout. After the grout injection phase was completed to a satisfactory level of confidence, rehabilitation activities started on the extraction level by taking out the now consolidated material from inside the drift in 2 m advances from under steel sets initially constructed in secured ground.Controlled blasting was the key aspect to the success of the initiative to open up just enough of the drift to systematically support the rock mass before the next set was installed. The systematic support consisted of in-cycle shotcrete sprayed over mesh pinned to the exposed rock, as effectively as possible, with splitsets before spiling the next advance’s protection canopy with rebar. Once secure, a combination of steel set and pumped concrete was installed as the final support. This final support provided a safe platform to repeat the process until the failed zone was safely traversed.CITATION:Kurniawan, A, Sjadat, A and Akhasyah, M, 2016. Rehabilitation of the collapsed panel 1K north in the Deep Ore Zone block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 763–768 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Physical/Chemical Treatment of Mercury-Contaminated Wastes from Former Chlorine-Alkali Electrolysis Plants - Application of Flotation Technologies in Soil Washing Plants

Sep 13, 2010

By K Firmin

The Mt Tom Price orebody of Hamersley Iron Pty Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the ore body, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control of products based on selective mining is the production of advance data on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades are determined from assay of samples taken from blast hole cuttings. As shales are more friable than hematite, product fines are always lower in iron grade than the lump product. The realisation of contract specification grade is more difficult with fines than with lump, so maintaining the correct fines grade becomes a prime factor in quality control. Control of fines grade is presently effected by aiming for an appropriate feed grade to the primary stockpile. Studies to estimate fines grade directly by qualitatively taking into account material types are in progress. Quality control measures are checked by monitoring the crushing and screening plant output, and taking appropriate compensatory actions in the mine when required. Minor fluctuations in quality of fines can be blended out on stockpiles. The quality control measures described ensure constant quality products, and a good recovery of high grade material from the deposit.

Jan 1, 1971

By B Chi, A Mahanta, R A. M Maddever, O Dominguez

BHP Billiton, in collaboration with Sodern and CSIRO, has developed a downhole logging tool for measuring geochemistry in situ. The FastGradeTM 100 (alternatively, FG100), exploits pulsed fast and thermal neutron analysis (PFTNA) to analyse the rock. This method is based on the detection and measurement of characteristic gamma rays emitted from isotopes in the material that become briefly radioactive when they are bombarded with neutrons. The tool outputs raw spectra arising from three types of neutron interaction, namely, inelastic scattering, neutron capture and neutron activation, which occur in successive time-windows (Smith et al, 2015). The spectra contain peaks at specific energies that are characteristic of the different elements interacting with the neutrons, the gamma count of which is related to elemental concentration. BHP Billiton uses in-house data processing software to convert the measured spectra to elemental concentrations.Much work has been done to understand the tool response under a wide variety of environmental and operating conditions, including logging speed, borehole rugosity, the presence of cavities, water etc. Effort has also been directed at understanding and quantifying the current sources of error in our conventional assays due to sample collection, preparation, and laboratory instrumentation in order to use this information as a baseline to compare against the FastGradeTM 100 results.To date, the FastGradeTM 100 primary use has been as a verification tool (JORC, 2012). However, beyond this, it has considerable potential to improve productivity in both exploration and production environments due to its ability to provide geologists with assay results soon after a hole is drilled.This paper presents initial test work and tool performance, including accuracy and precision under various conditions. Results are illustrated by comparing tool measurements to assays from laboratory samples collected from both reverse circulation and diamond-drilled holes.CITATION:Chi, B, Maddever, R A M, Mahanta, A and Dominguez, O, 2017. Near real-time assay with downhole assay tool (FastGrade™ 100), in Proceedings Eighth World Conference on Sampling and Blending , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By S M. Aminossadati, R Bagherpour, F Hasheminasab

Mine ventilation is an essential part of underground mining operations used to provide fresh and cool air, as well as to dilute and remove contaminants from the work environment. This paper presents an overview of the ventilation and gas management systems in one of the underground coalmines in Iran: Parvadeh_1 mine. The mine is located in the Tabas coalfield in the South Khorasan province. It is the only fully mechanised mine in Iran utilising the longwall retreat technique. The mine produces 1.1 to 1.3 Mt of coking coal annually. The mine ventilation system currently utilises two 630 kW exhaust surface fans. The gas management system includes surface to in seam (SIS) predrainage boreholes. The underground mine is equipped with an underground gas reticulation pipeline that is connected to a surface plant for the production of methane gas. This study shows that the ventilation and gas management systems of the Parvadeh_1 mine are in line with the standards of Australian underground mines.CITATION:Hasheminasab, F, Aminossadati, S M and Bagherpour, R, 2017. An overview of ventilation and gas management systems in an underground coalmine in Iran, in Proceedings Australian Mine Vent Conference 2017, pp 41–46 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Gold mineralisation at the Macraes Gold Project is hosted in the Hyde-Macraes shear zone and can be traced for ~30 km along strike, although economic resources are confined to a seven kilometre section in the vicinity of the Macraes  township. The shear zone, which typically dips at a low angle (~20¦) to the NE, is bounded by an upper hanging wall shear and a lower footwall fault. Mineralisation occurs along the hangingwall of the shear zone as well as in low angle concordant shears and stockworks. Ore types include graphitic cataclasites with variable amounts of quartz veining, 'lode schists' and quartz-vein stockworks. Mine geology and grade control activities are designed to ensure accurate definition of ore and waste as well as the accurate prediction of ore grade. Grade control involves an integrated process of blast hole sampling, geological mapping and geostatistical modelling. Geological mapping is carried out post blasting by means of excavating trenches across are zones defined by assay data. Conditional Simulation is used to model raw assay data to define ore-waste contacts and estimate ore block grade, although, geologically defined contacts have precedence. Low angle ore zones impart a wedge shaped geometry to many ore blocks. These ore blocks are bounded by contacts that can be selectively mined to, thereby reducing misallocation of ore and minimising grade dilution.

Jan 1, 2001

By M R. Stevens, W Mori, G B. Boswell

The Onemana prospect is located on the eastern Coromandel Peninsula, North Island, New Zealand. Systematic exploration involving surface geological mapping, geophysics, rock and soil geochemistry, reverse-circulation and diamond drilling has identified a number of important features of a fossil hydrothermal system at Onemana. This relatively intact gold mineralised system is hosted within a sequence of rhyolitic volcanics and volcaniclastics, overlain by lake sediments, sinters and hydrothermal eruption breccia. The system lies within a graben/half graben bounded by major NE-trending faults which form the approximate boundaries to hydrothermal alteration. Rock and soil geochemistry indicate a broad zone of anomalous gold, silver, arsenic, mercury and antimony. Overlapping elevated rock and soil gold anomalies indicate strongest mineralisation occurs over two zones of hydrothermal brecciation named 'Breccia Knob' and 'Western Ridge'. Geophysical data obtained from Gradient Array Resistivity and Ground Magnetics have been used to produce anomaly maps. The terrain corrected resistivity plot shows a number of well defined linear resistivity anomalies which are believed to represent large silicified and quartz veined bodies at relatively shallow depths. The strongest of these anomalies correspond with 'Breccia Knob' and 'Western Ridge'. Reverse-circulation and diamond drilling targeting these resistivity and geochemical anomalies has confirmed wide intervals of quartz veining, silicification and gold mineralisation. Petrologic data based on drill samples indicates the existence of a laterally extensive gold bearing epithermal system. Hydrothermal alteration is thought to have been caused by strongly convecting, two-phase (boiling), near-neutral chloride fluids which persisted at high temperatures (170 - 220¦C) to the paleosurface. A geological model is postulated of a large, complex, hydrothermal system developed in a shallow lake or marginal lake environment created by rifting and graben development within a recently extinct rhyolitic volcanic centre. Geothermal activity alternated between relatively quiescent periods of unrestricted fluid upflow and sinter development interspersed with violent hydrothermal eruptions caused by near surface silica capping and overpressuring above a major fluid conduit centred under 'Breccia Knob'.  Opportunities for precious metal mineralisation are evident from drilling to date. Upflow of near-neutral chloride fluids to shallow depths favours the presence of strongly mineralised stockworks at relatively shallow depths. Periodic hydrothermal eruptions would have caused fracturing and rapid depressurisation of the hydrothermal system, strongly favouring the precipitation of gold from solution both near surface and within feeder-vein systems at depth.

Jan 1, 1995

By S Smit, P J. J Strobo

ZINIFEX Century Mine is a zinc, lead and silver concentrate producer. Flotation is the primary method of minerals separation in this circuit. The flotation circuit is quite large with 79 flotation cells. The levels in each of these interconnected cells are controlled at more than 45 level control stations. Due to the multivariable interaction throughout the circuit, good level control was found to be difficult to achieve by just using normal Proportional-Integral-Derivative (PID) control. As a first step in advanced process control, the FloatStar Level Stabiliser, a multivariable controller developed specifically for flotation circuits, has been commissioned at Century mine to solve the level control problems. The first section of this paper therefore discusses and shows the results and improvements obtained by using the FloatStar level stabiliser. The results and benefits of the FloatStar Flow Optimiser are discussed in the second section of this paper.

Jan 1, 2004

By D Craw

TheSouthern Alps in the South Island of New Zealand are currently rising rapidly as a consequence of continental collision along the Pacific-Australian plate boundary. Rapid uplift has resulted in a major thermal anomaly in the shallow crust beneath the alps. Alpine topography and associated intense precipitation, coupled with the thermal anomaly are responsible for vigorous combined topographic/convective circulation of water through the shallow crust.   Uplift is greatest in a wedge-shaped region between the Alpine Fault and an associated second-order backthrust system, the Main Divide Fault Zone, approximately 20 km to the east. The Main Divide Fault Zone is segmented into NNE and NE striking faults, which are regionally sub-parallel to the Alpine Fault, but dip northwest in the opposite direction. Reverse oblique-slip on the Main Divide Fault is in an easterly direction, with a greater component of strike-slip movement on the NE trending faults. Elevated topography in the Mt Cook region is related to thrusting of a relatively homoclinal sequence of semi-schistose rocks on top of lower-grade greywacke, which controls the position of the Main Divide. Tectonically induced fluid flow resulted in only minor alteration and hydrothermal mineralisation of fault-rocks in Alpine and Main Divide Faults, and localised deposition of quartz and/or carbonate in the immediate hangingwall.   The wedge between the Alpine and Main Divide Faults is segmented by third-order structures north of the Mount Cook region. A series of right-lateral (-085/700S) and left-lateral (-150/600SW) faults, which are synthetic and antithetic to the Alpine Fault, respectively, developed as a conjugate set during uplift. Fluid-flow in the Southern Alps is controlled by these third-order fault/fracture systems. Cu-Au mineralisation, hydrothermal veins, and surface hot spring activity are localised by third-order fault/fractures and appears to be enhanced where conjugates intersect.

Jan 1, 1995

By B K. Hebblewhite, F T. Suorineni, J D. Tibbett

Block caving is an underground mining method that can provide high production capacities at low operating costs. This enables the profitable extraction of massive, low-grade orebodies and attracts industry towards the method. Block caving operations require significant initial capital investment and predictable cave propagation is crucial to safety and economic success. Lack of access to observe the caving process hinders our ability to learn how the rock mass and geological structures are reacting to mining. Virtual reality scientific visualisation (VRSV) enables the integration and investigation of multiple, large caving data sets and provides a viable alternative to visualise rock mass response without physical access to the cave. Point instrumentation is incapable of providing an overview of cave performance and seismic monitoring, while providing an overview of the rock mass and the response of structures to caving, is only useful when linked to the caving activities. The integration of point instrumentation data with seismic monitoring information, coupled with scientific visualisation of the mining system in a virtual reality environment, provides a powerful means for understanding caving performance.This paper describes the use of a VRSV module at UNSW Australia, designed for investigating the block cave mining system from a case study operation. This module has been used to investigate the location and chronological evolution of seismicity to understand sources of damage resulting in seismic space-time sequences (SSTS) in the caving system. The events within an SSTS represent damage that is spatially and temporally related. An SSTS group represents a collection of microseismic events from a reasonably competent region of the rock mass that has experienced a stress change significant enough to cause sequential damage. SSTS group locations have been seen to be the path of subsequent cave propagation. Thus, SSTS analysis enables insight to further our understanding of rock mass damage in caving geomechanics through analysis of historic data. Such insight has operational potential to learn from recent rock mass activity for optimising the management of undercut advance, draw front advance and cave draw patterns.CITATION:Tibbett, J D, Suorineni, F T and Hebblewhite, B K, 2016. Understanding damage source mechanisms in a caving system using virtual reality scientific visualisation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 439–452 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By V A. Tsukerman

Prospects a new energy saving method for an efficient destruction of the sturdy and hard materials (rocks, ores, frozen soils, concrete blocks, etc) û the Electric Pulse Discharge (EPD) method of materials destruction for green processing in mining and processing of mineral raw materials are considered.The EPD-technologies give additional possibilities for solving ecological problems at the expense of increase of integrated approach of utilisation of minerals and industrial wastes. The scientific and technical level of executed development of EPD method is sufficient for organisation of design work to develop substantially new equipment. A number of plants have been developed and tested, including plants for processing raw material with minerals of jewels, plants for selection of mica from rocks, and plants for processing the merging of artificial mica.

Jan 1, 2002

Processing of Hard-to-Treat Copper Ore and Flotation Middlings Using Chemical Treatment

Sep 13, 2010

By L Barro

There is currently a worldwide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow characteristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A capillary rheometer, designed to handle settling suspension, has been used for determining rheological properties. Brown coal of 0.0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦C - 319¦C. Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physicochemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage. Apparent viscosity increased sharply with increase in solids concentration and suspensions at higher concentration behaved as non Newtonian liquids. Viscosity decreased with increase in temperature; rate of decrease slowed down with increase in temperature.

Jan 1, 1980

By M P. Cipold, J F. Bachmann, C C. Bachmann, J Ha, H B. Wurst

In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink–?float analysis. Using traditional sink–float method it is not possible to sample and automatically measure. This fact, as well as time, cost and safety aspects, as well as required and manageable sample size of the sink–float method have prompted the search for a new approach for establishing separation performance criteria. This is especially important as performance levels of separator plants can be maximised if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes available in time. The new method to establish washability and associated performance information utilises at least two measurement technologies concurrently: single energy X-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy X-ray transmission and image processing.If used as a standard laboratory device the continuous build-up of the washability curve allows to evaluate the statistical significance of the sample size during measurement.The measuring method can even be improved if it is combined with an automatic sampling system that feeds a continuous and representative particle stream to the analyser. Then the value of the collected data increases considerably since the washability data are additionally available in time to be considered in the control of the process plant. The washability curve can be derived and is continuously updated based on the particles measured during the past time interval. Older curves and results are stored in a database and can be retrieved for later reference. This technology now enables automated sampling and integrated automated measurement, which was previously not possible.This incorporation of an automated washability monitor at a representative sample gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested using a range of samples with different densities, varying from 1 g/cm3 (coal) to 5 g/cm3 (iron ore).CITATION:Bachmann, C C, Bachmann, J F, Cipold, M P, Wurst, H B and Ha, J, 2017. Inline analysis of washability parameters for process control, in Proceedings Eighth World Conference on Sampling and Blending , pp 213–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

This paper sets out to discuss how alluvials - particularly mineral sands, tin and gold have adjusted to meet the problems of lower grade and more difficult physical political and economic conditions. The mineral sands industry seems to have adapted satisfactorily but less so with tin and gold.

Jan 1, 1996

Ledcap Pty Ltd has developed two software tools for assisting in the determination of life-of-mine (LOM) trucking requirements. The first tool generates haul paths and the second calculates truck travel time over these paths. The two step approach allows the paths to be viewed and if required edited, to better represent the actual site haul routes.The first tool automatically creates haul paths between the mine bench and the dump. To do this the user supplies a master haul route and a scheduled block model. The master haul path and the block model are interacted to create multiple haul routes, one for each pit/dump bench pair in each scheduling period. Each path carries with it a record of the scheduling period it represents and the dry tonnage hauled over the path in that period.The second tool calculates truck travel time over the path. Data from the manufacturer's rimpull and retarder curves are used to calculate accelerations and speed over each segment of the haul path. As the paths are derived from digitised representations of mine haul routes the path f les often have over a hundred segments. This detailed representation of the haul route allows the software to automatically adjust speed for different radius corners and accurately simulates the changing accelerations over the gradient changes that occur in real life mine ramps. Rolling resistance can be specified at a global level, at a segment level and at a period level. This allows rolling resistance to be changed seasonally as well as spatially.Life-of-mine trucking studies attempt to calculate an accurate answer from extremely variable inputs. This paper will detail the features of the two software tools and how the tools provided in the software can assist the mine planner to have greater confidence in their life-of-mine trucking requirements and the subsequent production capacity inputs to their scheduling calculations.

Dec 6, 2010

Laboratory-Scale Magnetohydrostatic Separator for High Resolution Density Analysis of Plastic and Other Wastes Recycling and reuse of different plastic wastes is still a current problem to solve for process engineers and it is true for seeking industrial applications as well as for smaller laboratory-scale, where a given waste sample, plastic or even metallic, has to be precisely separated into narrow density fractions to gain data for industrial design or for scientific research. The principle of magnetohydrostatic separators are known even there are industrial size machines but our primary aim was the development of a laboratory-scale separator for analysis of particles of densities up to 6 kg/L and sizes up to 8 mm. Main parts of the built experimental equipment are the ferrite core with two high power coils. The shape of the ferrite core at the two sides of the separator channel was specially designed to produce isodynamic magnetic field. In these places the ferrite core was constructed from laser cut ferrite sheets. The development of the high power electric supply for the two coils was a real challenge because the high voltage and current (400 V, 30 A) and because it had to be precisely regulated for being able to set discrete relative forces on the particles. Two separator channels were made from transparent plastic. The magnetic fluid is circulated by a centrifugal pump, fresh feed is supplied by a vibrated feeder and products can be taken by built in samplers. The velocity profile in the separator channel is measured by an ultrasonic Doppler velocity meter. Paper reports about the development and itself of the magnetohydrostatic separator and about some fundamental and applied laboratory experiments with different reference particles and wastes from used cars and electrical appliances.

Sep 13, 2010

Flotation of Composite Synthetic Particles

Sep 13, 2010

By R Lethlean

The mining industry in its drive to optimise equipment use and minimise cost simply to remain profitable in an uncertain commodity market needs to develop a greater understanding of equipment capabilities and cost. The factors influencing mobile equipment fleet cost and performance commence at the time of mine planning and continue to exert an influence over the life of the mine. These factors must be understood at the early stages of any operationÆs planning process as they continue to impact both positively and negatively on fleet performance and operating cost throughout the life of the mine. The key factors examined in this paper include: grades; rolling resistance; fragmentation and truck loading.

Jan 1, 1998