Search Documents

By D. K. Crampton, H. I. Burghoff, J. T. Stacy

The effect of cold-working upon electrical conductivity of copper and of copper alloys appears not to be generally known in detail. Although several papers on the subject have been presented, showing variable effects according to alloy composition, it is often assumed that the 2 to 3 per cent lowering of the conductivity of ordinary tough-pitch copper by severe cold-working is typical for copper alloys. Because of this situation it was decided to carry out the present work upon several types of copper, copper-zinc alloys over the commercial range of brasses, other binary alloys, and numerous age-hardening alloys in the quenched, and quenched and aged conditions. The large number of alloys investigated made it impossible to study every one in the detail it may have merited. Inasmuch as several interesting points that could not be satisfactorily explained came to light, further work is contemplated by the authors. It is usually considered that the normal effect of cold-work on ductile metals and unordered alloys is to decrease conductivity slightly. In alloys that are in the ordered state, as annealed or otherwise heat-treated, cold--working tends to disorder the structure, resulting in very marked lowering of conductivity. The random state of atomic arrangement produces lower con- ductivity than the ordered state for the same composition.1 Previous Work Previous work in the authors' laboratory has shown the electrical conductivity of several copper alloys to be decreased by greater amounts than might have been expected, in view of the general knowledge on the subject, when cold-worked. Guillet and Ballay2 investigated the influence of cold-work upon the resistivity of several metals and alloys, including copper and some copper alloys. The increase of resistivity due to severe working w is less than 4 per cent for all pure metals tested, while the increases for the alloys were generally higher. In the copper-zinc alloys, they found that the increase of resistance due to drawing increased with zinc content, and reported a 21.7 per cent increase of resistance for an alloy contaiiiing 67.9 per cent Cu as severely worked. Masima and Sachs3 studied the change in electrical resistance of three brass crystals when stretched in the tensile test, obtaining increases in resistance of the order of 3 per cent for 30 to 40 per cent reduction of area of the specimens. The resistance decreased again when the cold-worked crystals were subsequently annealed. Bardenheuer and Schmidt4 found that the conductivity of copper was decreased by 3 to 4 per cent when reduced 50 per cent by working. The conductivity of 72-28

Jan 1, 1941

By B. K. Miller, George E. Moore

THE Missouri fire clays are here divided into plastic and semiplastic clays occurring as widespread bedded deposits in east central Missouri and flint and diaspore clays occurring as isolated "sink-hole" deposits in the north central Ozark region. Visual inspection was the first method used in clay prospecting. Thin overburden, hard sandstone "rimrocks," and the occurrence of diaspore float made this method particularly applicable in the flint and diaspore fields. The first drilling tool used was a hand auger. One man can drill 25 to 50 ft. per day at a cost of about 35 cents per foot. Holes can be drilled to a depth of 150 feet. Spud drills are often used where the over burden is hard. This drill uses a slotted earth socket bit. A two-man crew can drill about 100 ft. per day at a cost of about 35 cents per foot. Mechanically powered auger drills have been used extensively in wildcat drilling in the past few years. This type of drill furnishes a continuous set of cuttings. The practical depth limit with this drill is 50 to 60 ft. Two men can drill 300 ft. per day at a cost of about 20 cents per foot. Core drilling is used mainly to prove a known clay deposit. A two-man crew with a No. 22 Sullivan drill can drill about 30 to 40 ft. per day in soft clay, at a cost of about $1.25 per foot.

Jan 1, 1947

By Mehl, Robert F.

IT has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relation-ship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solu-tions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available .2 Related to this latter class

Jan 1, 1934

By Robert Poole

On June 20, 1974, delegations representing the governments of 150 nations convened in Caracas, Venezuela. The occasion: the Third United Nations Conference on the Law of the Sea. (As this article goes to press, the conference is still in session-Ed). Of all the many issues to come before the conference, none is of greater long-term consequence than the issue of jurisdiction over the seabed-the "land" at the bottom of the world's oceans. On the agenda, with widespread support from a majority of UN members, is a proposal to declare seabed resources "the common heritage of mankind," under the sole jurisdiction of the United Nations. Any would-be miner of seabed minerals would have to apply to a UN seabed authority for a permit, and would be forced to pay the bulk of his profits to a UN fund to aid the underdeveloped countries.

Jan 9, 1974

By F. W. Schroeder

AT the annual meeting of the Institute 2 years ago, a paper,1 " Requirements of Refractories for Open Hearths," was presented by F. W. Davis and G. A. Bole of the U. S. Bureau of Mines. In a brief foreword, D. A. Lyon stated that the paper was not to report the results obtained but rather to present an outline to serve as a basis for discussion. The essential parts of an open-hearth furnace were described and the conditions under which they operate. Some constructive discussion followed the reading of the paper. One of the first fellowship investigations undertaken by the Bureau of Mines in 1924 under the cooperative agreement with Carnegie Institute of Technology, through the Metallurgical Advisory Board, was to determine service conditions of open-hearth refractories. The present paper gives the results of this work which was done in the Pittsburgh district and was in charge of the authors. Material contributions in the form of data were contributed by E. N. Bauer, J. W. Campbell, G. H. Pfeiffer and A. Grodner, Carnegie Institute of Technology research fellows. The study covered 18 mos.

Jan 7, 1926

By Robert E. Thurmond

DISCOVERY of a commercial ore deposit has resulted from a program emphasizing geophysical techniques and concentrating upon exploration of alluvial-covered areas. United Geophysical Co. selected these areas as offering the best possibility of success, for here the surface evidence of ore deposits has been hidden from the eyes of prospector and geologist alike. Pima mining district, Pima County, Arizona, was selected for initial exploration. The project was successful in that a commercial ore deposit was discovered and proved through drilling and extensive underground development. A limited region of activity was chosen and library research was begun on available economic and regional geological publications relating to the mining districts. Field reconnaissance of those districts which seemed to hold exploration possibilities provided a general picture and ascertained the existence of alluvial-covered areas of interest. At the conclusion of the reconnaissance trips all data obtained were compiled, and the district which seemed to present the best exploration possibilities was selected by statistical methods. The statistical summary was based on the following considerations: Geological Factors: 1—type of intrusive, P—presence of favorable host rocks, 3—apparent intensity of mineralization, and 4—presence of favorable structure in covered or unexplored areas. Economic Factors: 1—past production from district or mine; 2—size, shape, grade, and type of ore deposit in the district; 3—ease of acquiring mineral rights; and 4—general development facility. Exploration Favorability Factors: 1—results to be anticipated from geological methods alone; 2—application of geophysical methods, namely, topographic conditions, surface interference, depth-size relation, physical property contrasts as related to ores or controlling structural features; and 3—drilling factors. Admittedly, many of these, factors do not lend themselves to absolute evaluation, but relative evaluation, subject to inaccuracies of personal judgment, is always possible. A relative scale from 1 to 10 was established for every factor, representing varying degrees of favorability. For each district a numerical evaluation of each factor was established and a numerical total determined. The obvious advantage of this scheme is that a more concise summation can be presented by numerical means than can be achieved by descriptive means. After a district had been selected as favorable, the first step was to carry out more detailed geological and economic studies to narrow down the areas of interest. The second step was to compile all available geological data from publications and add to these data by mapping where necessary. Geological interpretation and projection of structural or other control into covered or unexplored areas was made whenever logical. To determine the possibilities of geophysical application and to select a geophysical method, physical property contrasts were related to mineral assemblages and/or structural control. If geophysics seemed applicable, trial profiles were run crossing the area normal to the strike and spaced

Jan 1, 1955

By A. R. T. Denues

LIQUID-OXYGEN explosives commonly consist of a carbonaceous absorbent enclosed in a canvas wrapper and soaked with a liquid con-taining more than 90 mol per cent of oxygen. Investigation of these explosives in this country was initiated in 1917 by George S. Rice, then Chief Mining Engineer of the Bureau of Mines. The early development is summarized in two papers.1,2 Their characteristics, advantages and disadvantages were considered in a recent bulletin of the Bureau of Mines.3 Other publications of this Bureau4,5 treat the technology of these explosives and contain adequate references to pertinent literature. These investigations defined the properties of liquid-oxygen explosives and improved them greatly; however, an outstanding disadvantage is their high inflammability, a property of critical practical importance. These explosives as hitherto prepared are easily inflamed; the combustion resulting from an accidental ignition is particularly dangerous because of the ease with which it passes into detonation. For this reason the Bureau of Mines undertook a cooperative investigation, which has resulted in the development of fire-retardant treatment for the minimiza-tion or elimination of this hazard without materially impairing the explosive properties, including the ease of detonation. This presentation will offer a general description of the investigation and the outstanding results. Further phases will appear in subsequent short papers, and the entire investigation including the results of detailed experiments will be available in a forthcoming bulletin of the Bureau of Mines (Bull. 429). The effects produced by fire-retardant treatments of the carbonaceous absorbent and of the canvas wrappers were investigated separately, and the efficacy of combinations of these treatments with particular reference to the possibility of inflammation and to the development of detonation from inflammation was studied. The experimental explosive was pre-pared from a granular carbonaceous absorbent and the results described may be more or less unique for such a material. An extensive preliminary

Jan 1, 1940

By K. Unrug, G. Herget, A. Smith

SUMMARY Statistics on roof falls indicate that the cost of just removing the unwanted waste from roof falls in US coal mines amounts to about $20 M per year. Almost 40 percent of fatal accidents occur under permanently supported roofs, indicating that the assessment of roof stability is still a very difficult task. In an effort to obtain a better understanding of roof fall occurrences, rock strength and ground stresses were determined in the roof of one mine each in Western Kentucky, northern West Virginia, and Eastern Kentucky. Triaxial ground stress determinations clearly show that horizontal stresses were higher than vertical stresses, and that maximum stresses in the horizontal plane were concentrated between the NE-SW to E-W direction, with the exception of the Eastern Kentucky site which was above the drainage. Magnitudes of stress components may vary considerably in one drlll hole. Strength tests of roof strata materials were done on core samples. Mapping of roof falls showed that the geometry of an opening or maximum span were not the overruling factor because in the same general area, a roof fall was observed in a room (entry) which connected two stable four-way intersections. It should be noted that, in very wet areas, the roof can break up to the bed where water is carried, and a very low ratio between extent of roof fall to height of roof, fall is observed. Geometry is, however, a contributing factor because nearly 70 percent of roof falls are intersection falls. The frequency of fractures parallel to bedding in failed roof strata is much higher than that observed in the original strata, indicating a significant amount of working in the roof before failure.

Jan 1, 1984

By J. H. Schulman, M. H. Buckenham

Although much interest has been taken in the use of mixed collectors in flotation, this investigation is probably the first in which oppositely charged collectors have been considered. The results obtained and the techniques used could well be applied in the behavior of other mixe the behavior of other mixed collector systems and could possibly explain the effective flotation results which have been reported when various collector combinations have been used. Collectors conventionally employed in flotation systems are soluble in water, but many of their homologs of longer hydrocarbon chain length are insoluble. The properties and behavior of these insoluble compounds may be conveniently studied when they are spread as monolayers at the air/water interface on the Langmuir-Adam trough. Although some extrapolation is involved in applying effects observed at this interface to the solid/liquid interface where the action of collectors is most important in flotation, the technique nevertheless is most useful for the study and interpretation of flotation phenomena. Of particular interest in this field are investigations on the insoluble monolayers of the fatty acids, alkyl sulfates and alkyl amines; the penetration of these insoluble monolayers by soluble surface active components and their interaction with metal ions from the underlying solution.'-' Unfortunately, the insoluble xanthates and related compounds do not exhibit stable monolayer properties due to rapid oxidation at the air/water interface and, therefore, cannot be studied directly in this way. These approaches have enabled Leja and Schulman8 to suggest mechanisms explaining dynamic attachment of mineral particles to air bubbles involving collector-frother interaction and the adsorption of collectors onto mineral surfaces. In this and other papers 9-12 considerable evidence is presented to support the concept of collector-frother and metal ion-monolayer interaction and to emphasize the value of monolayer techniques in elucidating the flotation system. Molecular interactions resulting from monolayer penetration are determined by the nature of and the association between both the polar and nonpolar groups of the two molecules concerned. Stable complexes are formed on penetration when interaction takes place between both the polar and nonpolar groups, and although the resultant complexes are not necessarily true chemical compounds, the properties of the molecularly associated complexes are very different from those of the individual components. Shortening of, or changes from, a straight hydrocarbon chain in one of the reacting molecules reduces considerably the stability of the associated complex as do changes in temperature, pH and substrate composition. The effect of hydrocarbon chain length becomes most important when observed effects are to be applied in flotation studies where soluble homo-logs and, therefore, much shorter hydrocarbon chain lengths are used. The present investigation is based on Langmuir trough work carried out by Bowcott,l3 who studied the penetration of insoluble amine monolayers by potassium lauryl xanthate. Bowcott observed that cetyl amine monolayers were readily penetrated by xanthate, but found that with time the high film pressures resulting from penetration and association fell off, indicating decomposition and ejection of xanthate from the film. This decomposition was pH dependent. Of particular interest in this work were studies on an equimolecular mixed monolayer of the fully N-substituted ammonium compound, for example, cetyl trimethyl ammonium iodide (CTAI) and potassium cetyl xanthate. Despite the fact that the CTAI is water soluble and the xanthate on its own is incapable of forming a monolayer, the mixed film was stable up to a surface pressure of 67 dynes per cm. In this condensed state the xanthate was stabilized against atmospheric oxidation, although iodine injected beneath the film caused an immediate collapse. The stabilizing of xanthate against oxidation by association with an alkyl trimethyl ammonium bromide (TAB) could be important in flotation, and a study of the performance and behavior of mixed collectors therefore was undertaken. A modified Hallimond tube operated under controlled conditions was used to evaluate flotation. Surface tension measurements were made to investigate the properties of the soluble

Jan 1, 1963

Jan 1, 1890

By L. B. Bramlett, S. L. Reyher, G. G. Southard

The Archean (2.65 billion years) aged Canning Stock at Copper Mountain, WY, contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interibr of the stock. Post-Laramide development of supergene enrichment blankets occurred in 25-100 m (82-328 ft) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanism proposed for deposition of pitchblende are sulfides, hydro-carbons, bacteria, the water table, or some combination of these. Abundant tar-type organics appear to have preserved the enrichment blankets from degradation. Trace element and radio-metric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1983

By R. W. Schenker

INTRODUCTION Environmental and occupational safety and health requirements often have a major impact on the design of comminution circuits, leading to increased capital and operating costs and reduced income. A project's capital cost can be increased by environmental permitting delays and the addition of dust collection equipment. Income can be reduced by lost production during unscheduled plant shutdowns for dust collection equipment maintenance. Dust collection equipment must be carefully selected and sized to minimize impact on the project. The equipment performance must comply with environmental regulations and allow working areas to comply with occupational safety and health regulations. Unnecessary overdesign could jeopardize the project's desirability from an economic standpoint. The equipment must be sufficiently reliable to avoid interference with production schedules. This chapter provides practical information on the selection and sizing of comminution circuit dust collection equipment that is consistent with the requirements stated above. It presents information on the reasons and general principles of dust collection; various types of dust collection equipment; and design criteria for ventilation hoods, duct systems, fabric filter dust collectors, and fans. An example discussing the selection and sizing of dust collection equipment for a simple comminution circuit is also presented. REASONS FOR DUST COLLECTION Dust collection equipment should be installed in comminution circuits for a variety of reasons, some of which are discussed below. These include compliance with government regulations, minimization of housekeeping requirements, product recovery, and improvement in public and employee relations. Compliance with Government Regulations Dust emissions from comminution circuits must comply with both air pollution control and occupational safety and health regulations. The regulations that may influence the selection of comminution circuits are discussed in more detail in Chapter 2. Air pollution control regulations limit the emission of dust, as well as visible emissions to the atmosphere and the concentration of dust in the ambient air. These regulations minimize the degradation of air quality and impact to other environmental considerations such as the health of the general public,

Jan 1, 1982

By James Aston

THREE years ago the writer presented a paper on the trend of development in the wrought iron industry,1 wherein was described a process in the development of which he has been a factor, which at that time had passed through several years of progressive experimental development but which had not then been put upon a commercial scale of operation. The present paper deals with two years of observation and experience in the commercial operation of a plant by the A. A Byers Co. at Warren, Ohio. It will not enter into the controversial field of the relative merit of wrought iron and steel in various classes of service, nor will it elaborate upon the characteristic services or fields of utility to which wrought iron is particularly adapted. It is sufficient to state that the wrought iron industry is upon a substantial basis and that the material finds service in pipe, where its advantages are in superior corrosion, fatigue, welding and threading qualities; in bar iron for staybolts, engine bolts, and rivets, demanding maximum service against corrosion and fatigue; in plates for corrosion service; and in chains, because of welding and shock-resisting characteristics. In short, ability to withstand the stresses of shock and vibration, or the ravages of corrosion, to hold protective coatings, and to give maximum efficiency in welding, are its features of relative superiority. If these features were not well recognized, the wrought iron industry would have shrunk to insignificance in the face of high costs and acknowledged limitations in manufacture. To charge that this industry is built upon a structure of assumption, psychology, and improperly weighed evidence is an impeachment of the integrity or belittling of the powers of observation of users through many centuries of service experiences.

Jan 1, 1929

By C. P. Proctor, J. T. Crawford, John Griffen

TROUGH washers were among the earliest methods used for concentrating ores; they are referred to by Agricola about the middle of the sixteenth century as already being used while the hand- operated jigging sieve had only recently come into use. For cleaning coal the trough washer apparently was first used in France and Belgium about 184.1. The early trough washers were intermittent and the refuse at least was shoveled out by hand. The invention of a continuous jig washer, by a Frenchman, Berard, in 1848, acted as a stimulus to coal washings in jigs and retarded progress in trough washing in the nineteenth century. Chapman and Mott 1 describe a number of trough washers developed in England and on the Continent from 1850 to 1900, such as the Bell and Ramsay, Ramsay, Bell and Green, Wunderlich, Scaife, McLellan, Lodge, Elliott, Blackett, and Murton. The later of these removed the refuse mechanically, either intermittently or continuously, but in ways that interfered with stratification. THE RHEOLAVEUR A Belgian engineer, Antoine France, is responsible for the development of means to remove refuse materials continuously from a trough washer, while preserving stratification and preventing the loss of coal with the refuse. The methods and equipment devised, which have become known throughout the world as rheolaveur, were initiated at the St. Nicholas mine near Liége, Belgium, about 1912. This installation consisted of two units to wash 20 to 8-mill. (3/16 to 5/16-in.) and 8-mm. to 0 (5/16-in. to 0), each having only two superimposed inclined troughs. The first few "Rheo" boxes on the top trough removed refuse directly and the remaining Rheo boxes discharged impure refuse to the lower trough for rewashing. On the lower trough the first few boxes removed refuse and the following boxes removed a middling product used for boiler fuel or other purposes. The overflow of both troughs was joined to form the washed coal product.

Jan 1, 1950

By James Aston

Three years ago the writer presented a paper on the trend of development in the wrought iron industry,' wherein was described a process in the development of which he has been a factor, which at that time had passed through several years of progressive experimental development but which had not then been put upon a commercial scale of operation. The present paper deals with two years of observation and experience in the commercial operation of a plant by the A. M. Byers Co. at Warren, Ohio. It will not enter into the controversial field of the relative merit of wrought iron and steel in various classes of service, nor will it elaborate upon the characteristic services or fields of utility to which wrought iron is particularly adapted. It is sufficient to state that the wrought iron industry is upon a substantial basis and that the material finds service in pipe, where its advantages are in superior corrosion, fatigue, welding and threading qualities; in bar iron for staybolts, engine bolts, and rivets, demanding maximum service against corrosion and fatigue; in plates for corrosion service; and in chains, because of welding and shock-resisting characteristics. In short, ability to withstand the stresses of shock and vibration, or the ravages of corrosion, to hold protective coatings, and to give maximum efficiency in welding, are its features of relative superiority. If these features were not well recognized, the wrought iron industry would have shrunk to insignificance in the face of high costs and acknowledged limitations in manufacture. To charge that this industry is built upon a structure of assumption, psychology, and improperly weighed evidence is an impeachment of the integrity or belittling of the powers of observation of users through many centuries of service experiences. In a history which extends to prehistoric time, and which is linked up with the earliest records of ferrous products, the dominant method of manufacture, as we have known it for little over a century, occupies a very small niche in the span of years that mark production and use of wrought iron. Puddling, the outstanding manufacturing method of

Jan 1, 1929

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By R. H. Hiltz, N. J. Grant

Solid-solution titanium-cerium alloys, cold-rolled to 0.010 in. thickness, and annealed, were internally oxidized to produce a fine dispersion of CeO2 in the titanium matrix. The oxidized alloys were cut into sheet stress-rupture specimens and tested for rupture life at 426°C, 538°C, and 648°C. There was noted an improvement in strength over that of pure titanium, the internally-oxidized alloys showing curves with a much flatter slope on the log stress—log rupture life plot, characteristic of the stable metal-metal oxide class of alloy. DURING the past 3 to 4-year period, considerable interest has been aroused by the potential offered by alloys based on the ultra fine dispersion of a hard insoluble phase in pure metals or solid-solution alloys for use at high temperatures. The impetus to the development and study of such alloys was provided by Irmann.1,2 through the success of the SAP alloy (pure aluminum containing about 12-14 volume pct of A12O3). Subsequent studies have thrown light on the true potential of this class of alloys in the remarkable stability of the structure after long-time exposure at high stresses and high temperatures.a-5 While success has been demonstrated in the special case of the A1-Al2O3 alloys, and more recently

Jan 1, 1959

By S. Harries Daddow

THE INSUFFICIENCY OF PILLARS OF COAL FOR THE PURPOSES DESIGNED-THE FRUITFUL CAUSE OF DANGER, EXPENSE, AND WASTE-THE PROOF OF INSECURITY-SUBSTITUTE FOR PILLARS OF COAL-PILLARS AND PANELS COMPARED. PILLARS of coal, which are designed and left in our mines as the means of supporting the overlying strata of our coal-beds, and securing protection to the miner, are not only insufficient for these purposes, but the most objectionable means of providing the desired security to life and property. Though such pillars are left at a great sacrifice to the owners of collieries and mineral lands, loss to the resources of the commonwealth, and ultimate privation to the public, they defeat the very ends for which they are designed, and not only do not secure life and property, but are as fatal to the one as ruinous to the other. Propositions.-It is eminently desirable that the resources of the commonwealth-particularly our mineral wealth in anthracite coal, which is limited-should be carefully utilized and made available, not only to ourselves but our posterity. Yet, speaking as an anthracite miner, we are wasting our resources of coal with a recklessness which will bring ruin in the end, unless checked, not only to the iron manufacturing interests of the East, whose chief protection, in competition with the iron-masters of the interior, lies in a cheap and abundant supply of anthracite furnace fuel, but to the best interests of the State. It is, consequently, not only desirable, but necessary, that we should realize every ton of coal from each colliery, and every acre of coal area, in order that our resources may not be wasted at present, to breed want in the future, and to realize the greatest present benefit to the mine, the miner, and the public. It is not possible, however, to secure these ends, if we continue to leave, as we do at present, from one-third to one-half our resources in anthracite as pillars in our mines. But our sad bills of mortality, our abandoned collieries, and our yawning mountain-sides, present ample evidence that even this enormous waste of coal, though left for the purpose of protecting life and property, is as totally inade-

Jan 1, 1873

By C. DeWitt Smith

"It just looks like everything is doing fine but humans," wrote Will Rogers fifty years ago. "Animals are having a great year, grass was never higher, flowers were never more in bloom, trees are throwing out an abundance of shade for us to loaf under. Everything the Lord has a hand in is going great, but the minute you notice anything that is in any way under the supervision of man, why, it's cockeyed." Do these words from two generations ago apply to oil shale? The United States has been blessed with deposits that can yield synthetic crude oil at a cost competitive with natural crude oil-under present economic conditions and with existing technology. Yet, the oil shale program is cockeyed because of the artificial obstacles that have been placed in its path "under the supervision of man." But more about this later. For the moment, let's focus on...

Jan 10, 1974