Search Documents

By O. Jay Myers

THE war effort has furnished the necessary impetus for better magnesium foundry practice. Four or five years ago, there were but a few formulas in general use for cores and mixtures for magnesium castings. Certain sands, binders, and inhibitors were specified and the proportions of these materials in each mixture were maintained between very narrow limits. As more and more war industries entered the field, much research was carried out and methods and practices were improved. Magnesium founding is still in a state of flux; therefore it is not uncommon to find one foundry spraying inhibitors on its cores, and another foundry using sand mixtures with incorporated protective agents. The basic core or dry-sand mold mixture for magnesium in use today is compounded with sand, core oil or resin binder, cereal, and moisture. Core oil or resin binder are added for baked strength while the cereal binder and moisture are for green strength. The normal mixtures (based on the weight of the sand) contain from 0.5 to 1.5 per cent of both cereal binder and core oil, and the moisture content varies between 1.5 and 5 per cent. The ratio of core oil to cereal binder varies from 60:40 to 40:60, while the correct amount of moisture depends upon the method of coremaking. PROTECTIVE AGENTS In all magnesium practice, protective agents are used in conjunction with the core and molding sands to prevent oxidation of the metal. The use of these inhibitors is not novel, but publications covering this field are not entirely adequate. Beck1 says Magnesium alloys decompose water to form magnesium oxide, hydrogen being liberated in the process (Mg + H20 -+ H21 + MgO). This reaction results in the blackening of the skin and the appearance of areas of porosity on the casting surface, the cavities of which are filled with a grey oxide powder (these are termed `burns'). Although sand cores for magnesium castings are thoroughly dried during the baking cycle, burning will take place on the castings unless the metal is protected properly. This type of burning is more difficult to define than the "water-magnesium" reaction cited by Beck. A possible explanation may lie in the following equation: 2Mg + 02 -s 2MgO Here, the source of the oxygen is not water, but the air in the mold cavity, together with the chemically combined oxygen in the core-binding media. Generally, two methods are used to prevent this reaction from taking place.

Jan 1, 1945

By Howard Eavenson

IN a discussion in the Transactions of the Institute (vol. xl, page 835 et seq.) the writer gave some data about explosions of gas and dust in the coal mines of the United States, Canada, and Mexico, among which was a table showing all explosions in the countries mentioned, in which five or more fatalities occurred, which had been reported from Oct. 2, 1871, to Mar. 28, 1908. Since the elate of publication of this discussion, as opportunity has presented, this table has been extended by the addition of explosions occurring since that time, by including several explosions which occurred prior to 1871, and by adding to the list all explosions of gas or dust in which less than five fatalities occurred, this having been clone by a search through the various mine reports, partly by the author and partly by the Librarian of the United Engineering Societies, and by correspondence with mine inspection officials of the various States, to all of whom acknowledgment of assistance is made: The accompanying list, Table I, is believed to be as nearly correct as such a statement can be made, and, while only extending to Dec. 20, 1912, contains all of the data now available in reports. An analysis of Table I, showing the occurrence by months of all explosions of gas or dust, including those in which less as well as those in which more than five fatalities occurred, is given in Table II. The statements are frequently made, in technical papers, that the number of explosions, particularly the larger ones, is increasing more rapidly than the number of mines, and that the number of fatalities caused by mine explosions, particularly the more disastrous ones, is increasing faster, proportionally, than the production of coal. To investigate the correctness of these statements Table III was prepared, in which the number of accidents and fatalities is taken from Table I, using those in the United States only, on account of lack of other data for Canada and Mexico; the production is from the records of the U.S. Geological Survey, and the number of mines, from 1909, from the same source; previous to 1909, the number of mines, for the decennial periods, was furnished by the U. S. Census records.

Jan 10, 1914

By J. A. Putnam, A. D. K. Laird

In laboratory research on the behavior of oil, gas and water in porous materials, no direct method has been devised to measure saturation without disturbing the flow. Indirect methods involving various forms of radiation have been developed for measuring one or two components. The X-ray absorption method for two components has been described previously1-3. The possibility of three component measurement has also been mentioned1. Since two component measurement still requires considerable care to insure accuracy, the fact that three components can be measured satisfactorily is not generally appreciated. The fraction of the energy of an X-ray beam of one wavelength transmitted through a material is given by the transmission factor. in which 1 is the beam's path length through the fluid. p is the fluid density, and 1,. is its mass absorption coefficient. Eq. 1 implies that all parts of the beam pass through equal amounts of the fluid. Practical applications are, therefore, limited to systems in which the fluid is distributed so that I varies negligibly over the cross-section of the beam. Typical variations of the transmission factor with X-ray tube potential arc shown in Fig. 2 from which experimental points have been omitted for clarity. The X-ray absorption of low pressure gases in a core is practically zero so it cannot he distinguished from that a vacuum by instruments that will differentiate between liquids. The transmission factor of a gas in a core is. therefore, unity. Consequently, the saturation of only one gaseous component can be found. If two fluids completely fill a core, their two saturations add to unity and, therefore, only one value of the transmission factor, T, is needed to determine both of them. When two liquids do not completely fill the core, their saturations do not add to unity and transmission factors at two wavelengths must be measured. At one of these wavelengths, 7 for one liquid must be different from T or the other liquid. The change of T for one liquid us the wavelength is changed between the two values must be different from the corresponding change of T in the other liquid. The two values of fluid saturation will also give that of the gas because the three saturations must add to unity. In Fig. 2 it can be seen that there are many large differences of T between various oil solutions and water solutions at any one potential, and between potentials for any one solution. Consequently, conditions for optimum accuracy of measurement of the saturations of a gas and two liquids can be chosen. Once the operating potentials have been selected, however. it is more convenient to cross plot the data from Fig. 2 on transmission factor-solution concentration coordinates for the chosen potentials, as shown in Fig. 3. Fig. 3 was used to plan the experimental procedure for Core N-38-1. Since the voltage control at 45 kv was good, the slopes of the curves in Fig. 2 at this potential would cause little error. At low potentials, however, the voltage control was not good, so 33 kv was chosen because the small slopes of the curves made voltage control less critical. The lowest strength beam that could be measured reasonably at 33 kv corresponded to a minimum T factor of 0.385. Fig. 3 shows that both 4.80 weight per cent of cadmium chloride in water and 24.0 per cent of iodobenzene in crystal oil had this T value, and, consequently, were indistinguishable to the X-rays at 33 kv. Thus, at 33 kv, the liquid saturation was given by the same curve regardless of the relative amounts of oil and water solutions present. This simple calibration curve from which the gas and liquid saturation can be read, is shown in Fig. 4. Fig. 3 also shows that at 45 kv, T for the aqueous solution is 0.610. and that T for the oil solution is 0.220. These values were transferred to Fig. 4 to give the triangular calibration plot from which the brine and oil saturations can be found, after the gas saturation has been determined at 33 kv.

By T. W. Harris

This paper was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the reduction of individual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States in order to consolidate the information developed from the many hundreds of boiler tests on coals consumed by various coal-burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal data, including description of coals used (with sufficient space to include first, second and third preference) on source of coal used, complete analysis and factors affecting choice of coal used. 3. Plant data, divided into: (a,) hand-fired, (b) overfeed stokers, (c) underfeed stokers, (d) traveling grate stokers, (e) pulverized coal; and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency data and remarks. The questionnaire was drawn up by consultation with various combllstion engineers, including B. J. Cross, Test Engineer of the Combustion Engineering Co., W. H. Fulweiler, of the United Gas Improvement Co. and the U. S. Bureau of Mines. In all, 11,538 copies of the questionnaire have been distributed, of which 4369 were sent in duplicate. Our estimate of the total volume of bituminous coal consumed in stationary steam boilers over the 12 months of 1930 is approximately

Jan 1, 1934

Jan 1, 1969

By P. T. Gallagher, W. A. Oates

THE partial excess entropy of interstitial solutes in metals, SXS , has usually been interpreted as being principally vibrational ever since the initial statistical treatment of hydrogen in metals by Fowler and Smith-ells. The vibrational entropy is considered being due to the optical modes of the light interstitial atom. Little attention has been given to the magnitudes of the values of SXS'. Leiser and Witte2 and Ebisuzaki and O'Keeffe3 have noted that for hydrogen in metals Si is approximately constant for different metals. On the other hand if it is assumed that the interstitial solute is an isotopic defect then, as shown by McLellan, SXS should vary from metal to metal as follows: where S is the standard entropy of the solvent and Mi, M, are the masses of the interstitial and solvent atoms. respectively. Fair agreement with this equation was found for oxygen in silver and nitrogen in iron4 and for carbon in iron.= Ln a subsequent analysis of metal- hdrogen systems McLellan' found a variation of $' from metal to metal but not in a manner expected from the isotopic impurity equation. However, a possible correlation between the energy of solution, Ei, and sf was noted. Similar correlations have been noted for certain dilute substitutional solid Solutions 7, 8 and recently Kubaschewski 9 has demonstrated a correlation between integral heats and ex-

Jan 1, 1970

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first. MISFIRES CAUSED BY FAULTY DETONATORS The important part of an electric blasting cap, to the user where multiple shot-firing is done, ass in the steep-pitch, thick-vein, anthracite mines, is the bridge wire. In single shot-firing this factor is not apparent, but in mines where multiple firing is done any variation in the resistance of the bridge wire, where full or even rated battery capacity is required, will most likely cause a misfire The reason for this is obvious. If the resistance in the bridge wires is not the same, some of the detonators will fire because of their greater comparative resistance. Variance in resistance of bridge wires is caused by a slight difference in the diameter of the bridge wire, also to a difference in the composition of the bridge wires. Again, where the bridge wires have become rusted, there will be a variance in resistance. About the year 1922, one of the large coal companies was greatly alarmed by the number of serious and fatal accidents caused by misfires. The general manager issued an order that these accidents must be greatly reduced, and if possible, entirely prevented.

Jan 1, 1929

By Bruce A. Kennedy, Richard M. Stewart

Slope stability has now become a practical tool in the design and operation of open pits. The selection of slope angles is a critical decision that can have far-reaching effects on the accumulated cash flow and the overall profitability of a mining project. Slope failures can now be dealt with in a number of ways. Two methods - the total removal and the partial unloading of a failing zone-have been practiced for many years. However, with the refinement of monitoring techniques, open pits can now learn to live with a slide and even turn a potential loss into a gain. There are various techniques, such as presplit blasting, drainage systems, and artificial stabilization, which can be applied immediately in an existing open pit to improve the stability of the pit slopes. The technology of slope stability will play an important part in the future mining of low grade, previously marginal orebodies, which will have to be exploited if the mineral needs of the world are to be met.

Jan 1, 1971

Canada's newest low-grade porphyry copper mine, Gibralter Mines Ltd. (N.P.L.), has reached production. The subsidiary of Placer Development Ltd., located at Williams Lake in the Caraboo District of central British Columbia, began open pit mining in mid-June on reserves estimated at 358 million tons assaying 0.373r: Cu and 0.016C; MoS,. Each of four separate zones will be mined in a predetermined sequence, in one or more stages, and with a throughput of more than 36,000 tpd. The sequence and stages of mining the zones have been determined by computer calculation and economic analysis and are designed to maximize recovery and minimize cost. At the very least, the mine is off to a promising start. Development costs leveled off at $67 million. 9'; below the anticipated budget.

Jan 7, 1972

By W. G. Matteson

THE origin of the salt domes of the Gulf coastal plain has been investigated by many of the most able geologists, but the problem cannot be said to have been satisfactorily solved. Since 1860, numerous theories have been presented, only to be discarded, at least in part, as more complete information revealed their fundamental weakness. Real progress toward solution dates from 1902, when Hill' advanced the theory of secondary deposition of the domal materials from saturated solutions of hot saline waters ascending from great depths under hydrostatic head along structural lines of weakness. Shortly thereafter, Harris,2 using Hill's hypothesis as a basis, explained the doming and pronounced uplift associated with these salt cores as the result of forces exerted by growing salt crystals. This was a marked advance over the ideas of Coste3 and Hager,4 since no. evidence of igneous intrusives, as they assumed to explain the uplifts, had been found associated with the domes. Harris5 developed his theory until it offered such apparently plausible explanations of so many details of dome phenomena that his hypothesis and conclusions received widespread acceptance, despite some serious objections, and today his theory, somewhat modified, is considered by many able investigators to be the best explanation of, the origin of these domes. The immense production of oil per acre, the recognition of the high lubricating quality of the oil, the development and recognition of the efficiency and advantages of oil-burning vessels, with the, subsequent

Jan 2, 1921

By J. H. Frye, S. G. Holder, E. E. Stansbury

Internal friction studies on annealed and cold-worked pure silver and alloys of silver with 4.5 atomic pct each of Cd, Sn, and Sb are reported. Small amounts of cold work, introduced by stretching pure silver, decrease the internal friction; large amounts of cold work, by wire drawing, cause this decreased internal friction to rise. Results of severol anneoling histories on the room-temperature in-ternal friction indicate a rather complex recovery and recrystallization behavior. A rather system-atic alloy effect is observed for the elements of Period V-B in silver in both the annealed and cold-worked states. DURING recent years internal friction measurements at very small stress levels have been interpreted in terms of structural models and mechanisms occurring within the metal or alloy.These measurements have been made over wide ranges of frequency of vibration and of temperature. While the effects of impurities, alloying, and plastic deformation have been studied by numerous investigators, no investigations of the effect of a series of solutes related by their position in the Periodic Table on a given solvent seem to have been reported. The present paper reports internal friction measurements on silver and on certain silver-base solid solutions to determine the values of room-temperature internal friction associated with varying amounts of plastic deformation and after different annealing

Jan 1, 1957

By R. J. Sweigard, R. V. Ramani

Demands on available lands will continue to increase due to the projected population increase and industrial expansion. Though there is an upper limit on available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as nonrenewable and renewable. Lands with minable resources can be dedicated at some Point to the extraction of resources. Such a dedication, however longterm, is only temporary because of the nonrenewable nature of the minable resources. The land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no nonrenewable uses are preempted and no renewable uses are permanently destroyed. This paper addresses primary aspects of this planning process. These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning, and a long-term plan for resource conservation and utilization. Minerals, with agriculture and forest products, are the primary sources of wealth. Therefore, to amid land development that may preempt future mineral resource utilization, local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more land use planning is needed for lands with mineral deposits.

Jan 1, 1985

By Thomas S. Blair

I FEEL a certain sense of responsibility in bringing before you the subject of the direct process in iron manufacture. I am aware that, in such a body as I have now the honor of addressing, there are few who are not already so well informed upon its past history that it would be a weariness to them to listen to anything else than an account of practical success. Yet, to claim that success involves so much that, if I do not make good my claim, I deservedly expose myself to severe criticism. The whole literature of the art, so far as it relates to the direct process, is, up to this time, but a history of failure. It is safe to say that more money, time, and talent have been fruitlessly spent in the pursuit of this object than in all the other unsuccessful efforts in the whole line of iron metallurgy. A distinguished authority in patent law has remarked that " the invention records of the United States and of foreign countries are filled with the waifs and abandoned relics of these abortive struggles." Dr. Percy, whose great work may be taken as an epitome of all that was worth mention, whether useful or curious, in pig-iron metallurgy, up to the date of its publication (1864), after giving elaborate accounts of various attempts at the direct process, condenses his own opinion of all that had been then effected, into a brief but summary comment upon a pamphlet of one of the sanguine inventors who had said: "It is evident that the present mode of working iron

Jan 1, 1874

By Anton Eilers, R. W. Raymond, O. H. Hann

THIS paper will treat of such works only as beneficiate ores directly in the mining districts. And when it is said that more than twenty

By Oliver Bowles

WHILE vast quantities of limestone and dolomite are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little attention compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux "that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate dis¬cussion of metallurgical limestone problems.

Jan 1, 1928

By J. B. Morrow, D. H. Davis

THERE are two general approaches to the problem of increasing profits from an operation. One is to lower expense; the other is to raise income. Mechanical preparation of coal may be used for either purpose but a prudent consideration of many details must precede any decision lest the results be negative instead of positive. It is quite possible that any net gain will result from a combination of the two. Since mechanically prepared coal invariably is a better product qualitatively than a hand-picked coal from the same mine, it is a reasonable expectation that the customer will be willing to increase the producer's income by paying a higher price. Or there may be the possibility that a combination of mechanical mining plus mechanical cleaning will give a lower over-all production cost for the coal in the railroad car. More likely, there will be found a combination of these two factors. From the customer's point of view, the competitive delivered cost per B.t.u. considered in relation to such incidental factors as dust nuisance, handling properties, ash disposal, and ash fusibility determines what he will pay. In-a bulk tonnage such as coal, freight is a very considerable part of the delivered fuel cost, and obviously freight paid on incombustible ash has no economic attractions. INCENTIVE FOR CLEANING Coal is prepared in four major ways: l (1) by screening or sizing, (2) by mixing or blending, (3) by cleaning, including hand picking and mechanical cleaning, (4) by dustless treatment. By a combination of any or all of these methods, coal can be prepared to standard specifications. It is easily possible to have good cleaning and still get a poor final product because of faulty screening or mixing, while it is possible to produce a very acceptable product from mediocre cleaning if the coal is well screened and mixed.

Jan 1, 1950

By J. E. Hanlon, S. R. Butler, R. J. Wasilewski

The temperature, orientation, and strain-rate dependence of tensile flow in single-crystal NiA1 of equiatomic composition have been investigated up to 800°C. Compression tests at room temperature have also been carried out. Optical and replica electron microscopy and X-ray diffraction methods were used to investigate the slip mechanisms. NiAl exhibits {110)(001) slip and cube slip {l00)(010) was also observed. This results in very high strength of single crystals in cube orientation. The implications of this slip mode, with the resultant small number of possible slip systems and three mutually perpendicular slip vectors, are discussed. ThE CsCl structure compounds represent a class related to the bcc elements, but their behavior is affected by three additional variables: composition (within the stability range of the compound), extent of long-range order perfection, and bonding energy. Very little data are available on the effects of these variables on mechanical properties. Rachinger and ~ottrell' suggested slip to occur along (111) in compounds of low ordering energy; in compounds of higher bond strength (>0.06 ev), they observed (110) (001) slip. As pointed out by copley,' only three in- dependent slip systems are available in the latter case; hence general deformation is impossible. Brown3 carried out a theoretical calculation of the yield-point variation with the degree of long-range order in the CsCl structure, based on the assumption of superdislocations. More general approaches, based on considerations of superlattice dislocations and antiphase domain boundaries in ordered structures, were carried out by Flinn~ and by Vidoz and Brown.' These, however, give no information on changes in the slip structure—if any—between the ordered and the disordered compounds. This aspect was investigated experimentally and theoretically by Stoloff and Davies' and by Marcinkowski and chessin7 in FeCo. The latter workers proposed the deformation behavior of the ordered FeCo to be essentially the same as that in many other bcc metals. Investigations of polycrystalline A~M~'-'O indicate considerable variation in mechanical properties with composition and test temperature. The existence of {123)(111) slip was reported in AgMg.'9'9'0 (The formation energy of this compound, presumed to be ordered at all temperatures below melting, is 4.38 cal per g-atom," i.e., 0.024 ev per bond.) The yield strength has been reported as relatively independent of temperature below 0.45 T, (where T, is the absolute melting temperature). Tensile deformation of single-crystal AgMg was also investigated by Kurf-man," who observed marked tendency to single glide on{112}(111) and {110)(111). From observations of slip lines in deformed poly-crystalline NiA1, Westbrook et a1.I3 suggested the

Jan 1, 1968

By Albert Hill Fay

In giving a sketch of the geology and mining of the tin-deposits of Cape Prince of Wales, a short description of the geographic and climatic conditions may be of special interest on account of this being a part of the world of which very little is known, even by the reading public. As shown in Fig. 1, the location of the Cape is lat. N 65° 35' and long. W. 168o. It is bounded on the north by the Arctic ocean ; on the west by Bering strait and on the south by Bering sea. It is the Westernmost point of the mainland of North America, and to the west, across the strait, one can see East Cape, Siberia, which consists of a rugged, steep coast of granite cliffs. The climatic conditions arc of interest because of the part they have had in the surface geology, and also because they affect mining from an economic standpoint. In connection with the climate and geography, it does not seem out of place here to quote a few lines from the prologue of The Wandering Jew, written by Eugene Sue, under the caption " The Land's End of Two Worlds." "The Arctic Ocean encircles with a belt of eternal ice, the desert confines of Siberia and North America—the uttermost limits of the Old and New World, separated by the narrow channel known as Bering's Straits. " To the north, this desert is bounded by a ragged const, bristling with huge black rocks. At the base of this Titanic mass lies enchained the petrified ocean (Bering sea) whose spell-bound waves appear fixed as vast ranges of ice mountains, their blue peaks fading away in the far-off frost-smoke, or snow-vapor. " Between the twin peak* of East Cape, the termination of Siberia, the sullen sea is Been to drive tall icebergs across a stream of dead green. There lies Bering's Strait. Opposite, and towering over the channel, rise the granite masses of Cape Prince of Wales, the headland of North America. "These lonely latitudes do not belong to the habitable world."

Jan 1, 1908

By M. R. Louthan

The susceptibility of titanium to stress orientation of hydride precipitates was investigated. It was determined that, when hydride precipitation occurred in titanium under an applied tensile stress of 30,000 psi, the hydrides precipitated on the titanium habit plane oriented most nearly perpendicular to the stress axis. Stress orientation of the hydride platelets occurred because the precipitation of the lower density hydride phase perpendicular to the stress axis caused expansion of the matrix in a direction that tended to relieve the applied stress. The Ti-H system has received considerable study in recent years, mainly because of concern over the effects of hydrogen on the mechanical properties of titanium. The amount of hydrogen present in commercial titanium is now quite low and should have no appreciable effect on its mechanical properties; however, many titanium applications require ex- posure to hydrogenous atmospheres under conditions in which hydrogen pickup is likely. In such cases continued exposures may cause the hydrogen content to increase to the extent that titanium hydride does precipitate as a second phase. The hydride phase has been shown 1,2 to have an adverse effect on the mechanical properties, particularly the impact properties, causing reductions in strength and ductility. BACKGROUND The behavior of titanium is often quite similar to that of zirconium and zirconium-base alloys, and the technology developed on one metal can often be applied to the other. Marshall and Louthan3,4 have shown that Zircaloy is susceptible to stress orientation* of zirconium hydride platelets, and that the platelet orientation has a pronounced effect on the mechanical properties of Zircaloy. They showed that when zirconium hydride precipitated in Zircaloy under an applied stress the hydride platelets tended to be aligned parallel to a compressive stress and perpendicular to a tensile stress. They also showed

Jan 1, 1963

By C. W. Washburne

Recently, Messrs, Mills and Wells1 published a thorough chemical study of the waters associated with oil in parts of the Pennsylvania, Ohio, and West Virginia region. Many of their conclusions are of general application and the writer wishes to discuss some of these. Messrs. Mills and Wells show that the composition of the deep brines oi the Appalachian fields is such as would be produced by the evaporation of sea water and the precipitation of sodium chloride, combined with reactions with hydrocarbons and other substances. The brines are altered, also, by considerable mixing with meteoric water. They give good reasons for believing that the concentration of the brines was produced by evaporation in the rock pores induced by migrating gas, much of which probably escaped to the surface of the ground. This hypothesis was considered by the writer in a former paperJ2 in which main stress was laid on a second hypothesis, that the excess of chlorine in the deep brines may have been due to the entrance of solutions rich in magnesium and calcium chloride which ascended from a deep, possibly intratellurie, source. Messrs. Mills and Wells present good arguments for the first hypothesis. Underground evaporation by ascending gases probably will be accepted as the best available explanation of the concentration and composition of deep well waters. They have not considered the possibility that salt waters in deep sands may be concentrated by the diffusion of water vapor through gas into shale. The writer has given reasons3 for believing that capillary forces concentrate gas and oil in the larger openings of rock, such as the pores of sandstones embedded in shale. The gas underground must be nearly saturated with water vapor at all times, because it always is in contact with the interstitial water of enclosing shales and of the sandstone. Experimental studies of soil moisture have shown that approxi-

Jan 1, 1921