Search Documents

By Harold W. Aldrich, Frederick Laist

After a series of experiments covering a period of about three years, extending from the spring of 1912 to the spring of 1915, a 2,000-ton leaching plant for the treatment of the accumulated copper concentrator tailing was built and put into operation. During the experimental period, the first step was that of laboratory experiments or beaker leaches. The results on this small scale were so satisfactory that a small operating plant, capable of handling 5 tons of roasted tailing per day, was installed. Again, the results proved satisfactory and an 80-ton plant was built and operated continuously from August until February, 1913. In this plant, full-sized roasting and leaching units were

Jan 1, 1917

By Ben E. Lindsly

PetRoleum engineers generally are familiar with the investigations of Dow and Reistle,1 Beecher and Parkhurst,2 and Dow and Calkin3 relative to the solubility of natural gas in crude oil. Since the publication of the results of those investigations and the work of Mills and Heithecker,4 little additional knowledge on this interesting and important subject has appeared in the petroleum engineering literature. The reports of Beecher and Parkhurst and Dow and Calkin agree substantially. The data from both investigations showed that, under the conditions of the tests, the solubility of natural gas in crude oil increased in direct proportion to the pressure at which the gas was put into solution, and the solubility decreased to a considerable extent with increased temperature. These facts, and others relating to the changes in viscosity, surface tension and specific gravity of the crude caused by the solution of gas in the oil, have been given due consideration in the petroleum industry, and the recognition of these facts has resulted in a great improvement in the technique of producing oil. However, in these first experiments, various grades and types of weathered crude oil were contacted at various pressures up to 500 lb. per sq. in. gage with gases deficient to a considerable degree in the heavier hydrocarbons, as compared with the gas that was originally in solution in the oil in its natural underground reservoir. The amount of dissolved gas that was liberated upon reducing the pressure to 1 atm. was measured. For these reasons, the complete significance of the effect of dissolved gases in crude oil, as it occurs in nature, cannot be determined directly from the data obtained under the conditions of the tests as described.

Jan 1, 1931

By G. A. Moore, D. W. Williams, C. E. Sims

During the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging, The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary ab- normal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. I, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. 'The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.' Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period of approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the System could be degassed thoroughly in

Jan 1, 1949

By C. E. Sims, G. A. Moore, D. W. Williams

During the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging, The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary ab- normal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. I, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. 'The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.' Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period of approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the System could be degassed thoroughly in

Jan 1, 1949

By John Rogers

The goal of a detailed quantitative understanding of the variables insulfide flotation in terms of established, or new, scientific principles is still distant, although there has been a good beginning in the past 50 years with more rapid progress since 1930. Advances have paralleled closely those in other branches of surface chemistry and the development of a series of experimental techniques such as contact angle, surface area measurement, radioactive tracers, infrared spectra, electron diffraction, monolayer, and electro- chemical methods of investigation. The second editions of books by Sutherland and Warkl ( 1955) and Gaudin2 ( 19571, are detailed accounts of this progress. The complexity of sulfide mineral flotation systems is indicated by Sutherland and Warkl who list 32 variables of flotation, of which only 22 can usually be controlled by the metallurgist. A consequence of this multiplicity of variables, many of which may be specific to each particular ore, is that ways of floating sulfide minerals from new ores are still developed empirically. How- ever, this review will try to show how the chemistry of the function of frothers, collectors, depressants, and activators in sulfide flotation is being steadily unravelled. Chiefly, it will be concerned with the interaction of pure soluble compounds with individual sulfide minerals, the surfaces of which are often not stoichiometric for several reasons discussed by Plaksin.3 As a result, for example, a freshly cleaved galena surface has cathodic and anodic areas which have different degrees of oxidation and different reactivity to- wards collectors like xanthate. Such complicating considerations should be remembered in the subsequent discussion of pure minerals. THE NEED FOR FLOTATION REAGENTS After considerable controversy it has been established with a few exceptions that unoxidized, uncontaminated sulfides will not float. Moreover all flotation plants recovering sulfide minerals use collectors which are removed from the circuit with the sulfides. Gaudin, Miaw, and Spedden4 have discussed the relation between the crystal structure of solids and the native floatability of the exceptions mentioned above. A second question which has been much explored is the nature of the surface on which a collector like xanthate is adsorbed or reacts. Is this the un- changed surface of the sulfide mineral, or does the adsorption depend on the initial oxidation of the sulfide surface ? Sutherland and Warkl and Gaudin2 discuss the work of Taggart5 and others on this question without reaching any other conclusion than that oxygen was important.

Jan 1, 1962

By F. A. Loving

This paper describes experiments which represent an effort to measure preciscly the pressure-time history in detonating condensed commercial explosives. The performance of explosives in mining has been a favorite subject for experimentalists and theorists for many decades. Much useful empirical information has been developed; but it has not yet been possible to predict, or even to account for, the behavior of explosives in mining on the basis of fundamental physical principals. A basic piece of information that would appear necessary for any rigorous analysis is the pressure-time history in the detonating condensed explosive. The experiments described here represent an effort to measure this relationship precisely in commercial explosives. THE EXPERIMENTAL METHOD The experimental method, first described by Cowan and Jacksonl has been extensively evaluated by Cowan and Balchan for relatively simple explosives. The experimental procedure involves the detonation of a layer of explosive between metal plates whose external surfaces are polished to a mirror finish (Fig. 1). Precise measurements of the deflection of

Jan 1, 1967

Jan 1, 1957

OUTSTANDING symbol of the machine age, the steam shovel needs no introduction. Few individuals there are, in the United States at least, that have not watched with fascination the almost human motion, the more than human strength, the rhythm of the whole steam-shovel cycle of crowding, digging, swinging, dumping, swinging, and crowding again. A mass of steel with some copper and other metals, fed with water and coal, guided by a single alert and dexterous operator, or perhaps two, does the work that would require 50 to 500 men or even more. The largest shovels working in the copper mines have loaded into waiting railway cars as much as 10,000 tons of ore in a single 8-hour shift. With no equipment but hand shovels, it would, in fact, be impossible to duplicate the work with any number of men; first, because they would be in each other's way, and second, because the steam shovel can lift single pieces of rock weighing 5 or 10 tons with effortless ease. Of recent years, internal-combustion engines and electric motors have displaced steam as a motive power in many instances; and of course the detailed design of the shovels has been improved immensely. Whereas the largest dippers used 30 years ago had a capacity of 3 ½ to 4 cu. yd., today the 350-ton shovel used at Chino has an 8-yd. dipper, as has the 320-ton shovel at Chuquicamata. Incidentally, for stripping at coal mines a shovel having an 18-yd. dipper is in use. However, the principle of operation of the modern shovel, regardless of the size and type of motive power, is essentially the same as that of the earlier shovels. It is fair to say that the indispensable of open-cut mining is the steam shovel, or, to be more precise, if perhaps less picturesque, the power shovel. Somehow the electric shovel seems to lack the glamour that

Jan 1, 1933

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined because it is used both as a rock term and as a particle size term. Actually most persons using the term clay realize that it has a double meaning and in most instances define it. As a rock term, clay is difficult to define because of the wide variety of materials that compose it so that the definition has to be general. Clay is a natural, earthy, fine-grained material composed largely of a limited group of crystalline minerals known as the clay minerals. Many definitions state that a clay has the property of plasticity when wet, but some clays are not plastic, i.e., halloysite and flint clay; however, most clay materials are plastic when wet. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on some grade scales. Soil investigators and mineralogists generally use 2 microns as the maximum size. The Wentworth scale' defines clay as material finer than approximately 4 microns. Grim' has found it convenient to use the term clay material for any fine-grained, natural, earthy, argillaceous material and in this way can include clays, shales, or argillites, and some soils if they are argillaceous. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, still the term is generally understood by all who use it. Clay is an abundant natural raw material and has an amazing variety of uses and properties which will be discussed in this chapter. In order to understand better the relationships between the clays and their uses, a brief discussion of the structure, chemical composition, and identification of the clay minerals is given. Mineralogical Composition of Clays Clays are composed of certain groups of hydrous aluminum, magnesium, and iron silicates that may contain calcium, potassium, and other ions, which are called the clay minerals, and other minerals of variable composition, which are nonclay minerals. Both clay minerals and nonclay minerals influence the properties of a clay material. In order to understand the relationship between clay minerals and the properties of a clay material, a short summary of the structure and composition of clay minerals is necessary. Any scheme of classification tends to impose a certain rigidity and as new and additional data become available it is necessary to revise classifications. Brindley3 has discussed the classification and structural mineralogy of clays in very lucid fashion and chose a classification based on structural features and chemical composition. Grim2 proposed a tentative classification which is based on the structural attributes of the various clay minerals. This classification is relatively simple and workable, and is shown as follows: I. Amorphous Allophane group II. Crystalline A. Two-layer types (sheet structures composed of units of one layer of silica tetrahedrons and one layer of alumina octahedrons). 1. Equidimensional Kaolin group kaolinite, dickite, nacrite 2. Elongate Halloysite group

Jan 1, 1960

Jan 1, 1970

By H. F. Easter

The lead department of the El Paso Smelting Works at El Paso, Tex., is operated strictly on a custom basis. The ores treated are drawn from the surrounding territory, comprising New Mexico, Arizona, western Texas, and northern Mexico. Ores received from the last-named section originally amounted to a very large tonnage, but. of recent years have dwindled into comparative insignificance so far as this plant is concerned. This has been due partly to the establishment of a lead-smelting plant at Chihuahua, which is much closer than El Paso to most of the important mines, and partly to the recent revolutionary troubles in Mexico. There are no mines of either lcad or copper in the immediate vicinity of El Paso. In general, it may be said that the lead-ore supply of recent years has been uncertain and precarious, with a general tendency toward an excess of silica and a shortage of iron. This latter requirement has been met in large part by the use in El Paso lead furnaces of considerable amounts of roasted leady copper matte from the Chihuahua smeltery and of converter slag from the El Paso converters. These two materials, coupled with complex lead-copper ores from Bisbee, Ariz., have introduced into the lead-smelting operations a most unusual amount of copper, which has had an important bearing upon the smelting practice of the plant. his matter will be discussed later. The ore, loaded in either box cars or gondolas, enters the storage yard on four tracks elevated about 8 ft. above the ground. As all unloading is done by hand, unloading platforms at the height of the car floor parallel the tracks on each side to afford a runway for wheelbarrows. At frequent intervals these lengthwise platforms are joined together by others running crosswise to facilitate the distribution of the ores evenly over the beds, which are located below and between the tracks. At present much of the bedding space formerly used for lead ores is given over to the copper department, but 20 bins of various sizes are retained for the use of the lead furnaces and the Huntington & Heberlein roasting plant. The largest of these holds about 1,000 tons, while the smallest holds not over

Jan 1, 1916

By J. L. Bray

IT is well known that iron markedly improves the physical properties and casting characteristics of aluminum bronzes. The use of 1 to 4 per cent iron as the principal modifying addition has become common practice in many foundries melting aluminum bronzes. Although the beneficial effects of iron are unquestioned, there is some uncertainty regarding the structural changes caused by it in the basic copper-alumi-num system. It is agreed that a new constituent appears in abundance when the iron content reaches 2 to 4 per cent. This constituent, which frequently occurs in shapes resembling clover leaves, is sometimes assumed to be an aluminum-iron intermetallic compound. If this were correct we might expect a change in the structural relationships of the matrix in the direction of decreased aluminum content. On the other hand, it has been reported that iron has a negligible effect in altering the fundamental relationships of copper-aluminum alloys1. Others2,3 have reported an additive coefficient. Apparently it will be necessary to know the equilibrium relationships between the phases of the copper-aluminum-iron alloy system to establish any such theory as fact. When this has been done it may very well be that a further revision in the structural relationships may be necessary to describe the changes to be expected in commercial cast alloys. It was with this latter problem before them that the authors attempted to

Jan 1, 1936

By M. N. Dunlap

This article summarizes the successful incorporation of a flash-flooding stream into the tailing-disposal system at the St. Joseph Lead Company's Federal Division mill, in St. Francois County, Missouri. The mill was built in 1906, by the Federal Lead Co., as its No. 3 mill for the concentration of southeastern Missouri lead ores, and damming Davis Creek was first considered in 1908. Plans were made also in 1925 and in 1937. Dam layouts varied from a reinforced concrete structure to a barrier built of tailings alone. .All were abandoned because of liability that would be incurred by flash-flood rupturing of an incompleted dam. By 1942 mill capacity had reached 12,000 tons daily and increasing tailing-disposal costs again focused attention on the Davis Creek basin. This time the problem of riskless dam building was solved. Moreover, most of the items that appeared in the answer were materials that normally required wasting and the major portion of labor involved performed functions that it mould normally have done, without constructive benefit, elsewhere. The new layout also made possible advantageous changes in mill-water supply pumping; static head being reduced from 514 ft to 9; ft, friction head from 4900 ft to 2860 ft, and pumping can be done now at periods of low power demand. The following facts about the Davis Creek watershed explain the 36-year reluctance to reach these, and other, benefits. Size: 3600 acres. Outline: roughly pear-shaped, 21/2 by 3 miles at the largest dimensions. Topography: mostly hill land with steep valleys. Relief: 760 minimum to 1153 maximum. Maximum rainfall: 3.36 in. per hour. Permanent water: none natural. Now 2200 gpm discharged through 16-in. drill hole from mine pumps underground. Geology: the 17 acres near dam centerline is Bonne Terre dolomite covered with sand and gravel eroded from Pleistocene beds that cap some of the hills. The remainder of the pond basin is on Davis shale. Soil cover: mostly second-growth timber with some abandoned fields; all subject to careless burning, which reduces water-retaining ability. Flood history: flash-flooding that had taken at least one life. Downstream values: two railroad bridges before creek intersection with Flat River. Immediately below confluence, a highway bridge, a low-water crossing, a few business establishments and several blocks of residences. In July 1942 the following segments of an ingenious plan were put into operation. A ditch 270 ft long, 16 ft wide and 51/2 ft deep was excavated to bedrock in the gravelly soil along the proposed dam's centerline. This excavation, which exposed many gravel-filled channels, was run full of slimes drawn from a riser set in the top of an adjacent tailings-disposal

Jan 1, 1949

By C. A. Heiland

A. INTRODUCTION (C. A. HEILAND) I. PRINCIPLES OF TEMPERATURE COMPENSATION IN MAGNETIC INSTRUMENTS The principle underlying the majority of magnetic intensity variom-eters is a comparison of the force to be measured with another force of known magnitude. The known force may be (a) of a magnetic nature, such as magnetic fields produced by magnets or coils, or (b) of a mechan-ical nature, such as (1) the elastic forces of wires, or (2) the force of gravity, such as employed in bifilar magnetometers and magnetic balances. In instruments of such type, usually a magnetic system is employed, free to move about either a horizontal or vertical axis, on some sort of a suspension. If the earth's magnetic field alone were present, such a system would adjust itself into the direction of the field or that of its components. Owing to the simultaneous action of the comparison force, however, the magnetic needle assumes a position that differs from the direction of the magnetic force; for all such instruments, the angle of deflection a is given by tan a = F/X, where F is the known and X the unknown earth magnetic force component. In other words, the magnetic system merely serves as an "indicator" for the position of balance of the two forces. Considering the matter from this point of view, it is not immediately obvious why the temperature of such a magnetic system should modify the results. In magnetic instruments, we may distinguish two different effects of temperature: (1) a magnetic effect and (2) a mechanical effect. The first is due to the fact that the magnetic moment of a magnet drops with an increase in temperature. This drop is characterized by the temperature coefficient of the magnetic moment µ (see equation 1). The second effect is due to the change in the .torsion of suspension wires with temperature or to the expansion of lever arms of masses acting on magnetic balances.

Jan 1, 1932

By C. H. Wilson, J. W. Daly, J. J. Jakosky

Meteor Crater, Arizona, is a natural wonder which for years has been the subject of considerable discussion and study as to its origin and age (Fig. 1). Of the various theories advanced regarding the origin, two have been considered as most probable by a majority of investigators. The first theory is that the crater was formed by a meteorite or a swarm of meteoric material striking the earth at a high velocity and burying itself. The second theory is that the crater was formed by a "steam explosion" from hot solutions or gases coming from underneath the present sedimentary beds which overlie the area. In order to obtain more detailed information regarding the conditions existing at the crater, the present management decided to have a detailed geophysical examination made. The origin of the crater is of considerable scientific importance and interest. More or less active mining operations have been carried out during the past 20 years by various groups who believed that the crater was of meteoric origin, and who hoped that sufficient quantities of such material had been buried to be commercially valuable. Fragments of meteoric material found on the surface of the ground in the debris around the rim gave analysis of approximately 92 per cent iron and 8 per cent nickel, with some platinum and iridium. The material having a gross value of approximately $50 per ton, mining would be commercially profitable if sufficient quantities of the material existed in condition for mining. In the early work numerous drill holes and shallow shafts were put down, mainly in the northern portion of the crater. Pulverized material and debris caused considerable difficulty, and in an effort to overcome this the present management started a 1500-ft., two-compartment shaft on the south rim of the crater and outside of the fill zone. The intention was to sink the shaft in the solid rock outside of the crater, and then to crosscut toward the crater at a depth of 1500 ft. The work was finally stopped when a depth of 650 ft. was reached, because water poured into the shaft through large cracks and fissures in the rock. The enormous force responsible for the crater had also broken

Jan 1, 1932

By Zay, Jeffries

THE effect of thoria (ThO2) on grain growth in tungsten was discussed in some detail in a paper presented before this Institute by one, of the authors in 1918.1 In that paper it " was assumed that the, thoria was present in the tungsten entirely as a mechanical mixture. There was no indication in the experiments described that even a trace of the thoria was in solid solution in the tungsten. Langmuir,2 however, observed that thoriated-tungsten filaments under certain conditions showed electron emissions many thousand times greater than unthoriated tungsten at the same temperature. He concluded from his studies that a slight amount of the thoria had dissociated on heating the filament to a temperature near 220°. C. At this temperature and higher, part of the thorium diffuses to the surface of the filament where it evaporates at. a much faster rate relatively, than the tungsten, and also at a rate, nearly as fast as it is brought to the surface by diffusion: If the temperature is lowered to say 1800°,. C., diffusion of the thorium atoms to the surface is more rapid than evaporation, sown adsorbed film of thorium atoms is produced on the surface of the tungsten filament. The electron emission is governed by the outside layer of atoms so the emission from such a filament might be expected to approxi¬mate that of a thorium filament at the same temperature. PRESENCE OF METALLIC THORIUM IN THORIATED TUNGSTEN If the filament containing the adsorbed film of thorium. is heated to a sufficiently high temperature, the thorium atoms evaporate: rapidly and the electron emission becomes more nearly that of tungsten. On cooling again to 1800° C., or thereabouts, the emission 'builds up gradually to a maximum. The filament containing the adsorbed layer of thorium atoms is said to be "activated." By studying the rates of activation under different conditions of prior thermal treatment and at different temperatures, Langmuir was able to arrive at an estimate of the

Jan 1, 1927

By B. H. Bergstrom, D. D. Crabtree, C. L. Sollenberger

Experimental data is given for several natural minerals on the load required for the fracture of single specimens over a very wide size range. The experimental results are compared with published data, such as for coal specimens from 30 to 64 in. in size. Correlations of the specific energy (per unit mass) required for fracture with specimen size are given as functions of specimen shape and the experimentally observed load-size relationships. These correlations are discussed with reference to comminution theory. Comminution, through compression or impact, can result only if sufficient force, or energy, is applied to a specimen of a given size. The relation of specimen size to force requirements has not been adequately considered previously. For single particle fracture, it was previously shown 1 that the specific energy (energy, e, per unit mass, M) at fracture of single glass spheres was inversely proportional to the product size modulus, k, as indicated in the equation: e/M = C/k [1] This was found true not only for numerous glass specimens of the same nominal size but was true for all nominal sizes tested from 1/8 to 1 in. Also, it was observed that the smaller spheres required a greater specific energy at fracture than the larger spheres and consequently had a smaller product size modulus. However, the relationship giving the required fracture energy as a function of specimen size was not further elaborated upon. This paper will extend the development of the feed size effect on specific fracture energy for brittle materials. SPECIFIC ENERGY-FEED SlZE RELATIONSHIPS FROM PREVIOUS DATA For the particular glass spheres tested in the previously described experiments,' it can be shown, as on Fig. 1, that the specific energy varied inversely as the 4/3 power approximately of the feed size, F, in the span of nominal sizes ranging from 1/8 to 1 in. The load at which a 3-in. diam glass sphere (a crystal gazer's ball) was broken was within the range predicted by an extrapolation of this energy-feed size relationship. The product size distribution from this

Jan 1, 1963

By Keith R. Bock, Norman Parlee, Albert M. Barloga

Coils of pure iron and iron-carbon alloy wire (0.05 to 0.80 pct C) and sufficient sulfur to saturate the solid phase were equilibrated in evacuated or argon filled tubes. After rapid cooling, and removal of the outside nonmetallic layer, the wires were analyzed for carbon and sulfur and the data used to construct an Fe-S binary and isotherms of the Fe-C-S ternary in the range 1149° to 1427°C. THE solid solubility of sulfur in steel is of interest in connection with such phenomena as hot shortness, burning, and so forth. "Burning," the more or less permanent damage that some steels suffer when heated for forging or rolling, has been shown to be related closely to the behavior of sulfur and less closely to carbon and oxygen.' Attempts to interpret burning phenomena in steels fail because of lack of data on the Fe-C-S and the more complex systems in this family. Rosenqvist and Dunicz 2 and Turkdogan, Ignatowicz, and pearson3 have largely elucidated the Fe-S diagram in the region of interest but no information on the Fe-C-S diagram in this region appears to be available in the literature. This paper deals with the elucidation of the Fe-C-S diagram in these interesting ranges. The method employed is different from those used by previous workers2'3 on the Fe-S system. EXPERIMENTAL METHOD Pure iron wires (Ferrovac E) or iron carbon alloy wires of 1 mm in diam were cleaned with acid and acetone, coiled, and placed in silica tubes (7 mm OD and 5 mm ID) previously closed at one end. Enough sulfur was added to assure saturation of the solid iron phase. The filled tubes were either simply evacuated and sealed, or filled with argon at a reduced pressure and sealed. The argon was required at the higher temperatures to prevent collapse of the tubes. The filled and sealed tubes were placed in the middle uniform temperature zone of a Globar tube furnace and equilibrated at temperatures ranging from 2100°F (1149°C) to 2720°F (1493°C). After equilibration the tubes were removed from the furnace and quenched in air or water, the form of quenching being found to have no effect on the results. The tubes were broken open and the coils were placed in a 1 : 1 HC1 solution to remove the sulfide-rich layer. The coils were then cut into small pieces and analyzed for sulfur and carbon. In the early stages of the investigation different equilibration times ranging up to 17 hr were tried and the cores of the wires were analyzed to test for saturation. One hour appeared to be sufficient to reach maximum sulfur content at 1454°C and 2 hr sufficient at 1149°C. The practice adopted was to use at least 3 hr at the higher temperatures and at least 5 hr at the lower temperatures. The iron-carbon alloy wires used were made by carburizing pure iron wire with carbon monoxide gas in a one inch diameter ceramic tube at about 1204°C. Differing carbon contents were obtained by allowing fairly large coils to react with the gas for varying lengths of time at a flow rate of 800 cc per min. The reacting times ranged from 15 min to 4 hr depending upon the amount of carbon desired. The furnaces used were controlled by means of Leeds and Northrup Speedomax Type H instruments with D.A.T. Control attachment. Thermocouples were calibrated against the melting points of gold and copper. The temperatures recorded appear to be accurate within i2.7OC. Starting with run No. 85 and continuing with the

Jan 1, 1962

By P. R. Schmidt, N. J. Themelis

A study zvas made of the deoxidation of copper at 1170°C by injecting a jet of carbon monoxide vertically upwards into the melt. The effects of submersion depth (2 to 20 cm), orifice diameter (& to 5 in.), and gas velocity (100 to 3650 ft per sec) were examined. In the oxygen range 0.1 to 1.0 pct 0, the overall rate was conlrolled by gaseoLcs mass Lransfer. The results were interpreted in terms of a rate coefficient per unit depth which was found to be constant with distance along the jet axis and nearly proportional to the orifice Reynolds number in the range 1000 < NReo < 9100. AS the gas flow rate through an orifice submerged in a liquid is progressively increased, at least three regions of bubble formation may be distinguished. At very low rates, the formation of bubbles is practically a static phenomenon, depending on the orifice diameter, the liquid surface tension, and the densities of the two phases. In this region, the bubble size is constant while the frequency of bubble formation increases with gas flow rate.&apos;-3 At higher flows (500 < NR~, < 2100), the frequency of bubble formation reaches a steady value and the bubble size increases with gas flow rate; when the bubbles issuing from the orifice become so large that they start coalescing to form larger bubbles, the turbulence induced in the liquid by the passage of previous bubbles shatters them into small bubbles of varying size. Finally, for gas velocities in the intermediate and turbulent regions of flow (NR,, > 2100) a tangential separation surface is created around the jet and momentum transfer takes place between it and the surrounding liquid medium. The entrainment of liquid and the resulting deceleration of the gas-liquid dispersion causes the jet to expand forming a characteristic jet cone. The large velocity and density differences between the jet and the liquid result in a high degree of instability and the jet envelope fluctuates rapidly.The characteristic jet cone can be observed by means of time exposure photographs such as those shown in Fig. 1 for an air jet introduced vertically upwards in a water bath. High-speed photography has showns that the gas-liquid dispersion within the cone consists of small bubbles the size of which depends mainly on the jet orifice diameter and Reynolds number. In the laminar region of flow, the following correlation was obtained by Leibson: The results of Liebson et a1.&apos; are plotted in Fig. 2. It can be seen that the region 2000 < NReo c 10,000 is not well-defined experimentally. In the entrance to the fully turbulent region of flow (NR,, = 10,000), the mean bubble diameter decreased to about 0.4 cm and varied only slightly from there on according to the correlation:

Jan 1, 1968

By José G. Aguilera

With the imperfect knowledge that me have of the geology .of the country in general, and of the numerous mining districts in particular, it is impossible to present an accurate idea of the geographical and geological distribution of the mineral deposits of the Mexican Republic. But, notwithstanding this, it is elear that the deposits are concentrated in limited regions of the country, and that certain deposits are so closely associated as to indicate, beyond doubt, a genetic relationship. The mineral deposits are numerous, and the most of them are found in the western part of the country in a zone following a SE.-NW. direction from Oaxaca to Sonora. In the eastern

Jan 1, 1902