Search Documents

By Richard A. Busch, Roy L. Soderberg

Large, high, open stopes resulting from vertical crater retreat (VCR) and similar methods are usually filled with sand tailings to support the stope walls and make it possible to mine the pillars. The hydrostatic head resulting from these high stope fills demands extremely heavy bulkheads in the crosscuts to withstand the pres- sure. Occasionally, these bulkheads fail because there are no drains or the installed drains are inadequate. Costly flooding of the mine and loss of life result from these failures. With proper design of blanket drains and filters, the fill can be made failure-proof, requiring only a minimum bulkhead, designed specifically for zero water retention. The effectiveness of the blanket drains can be increased by laying perforated pipes on the bottom of the crosscut within the blanket drain. These drains can have a safety factor of 10 with minimal expense. When the water is properly drained, the hydrostatic pressure on the bulkhead is reduced to zero, leaving only the lateral pressure of the sand. This lateral pressure is partially dissipated by arching and shear against the crosscut walls and consolidation of the tailings as the water is drained. The bulkhead should be placed at least one cross-cut diameter back from the collar of the drawpoint.

Jan 1, 1983

By R. A. Wolfe, H. W. Paxton

Self-diffilsion coefficients for cr51 and Fe55 in 12 pct Cr-Fe and 17 pct Cr-Fe for Fe55 in chromium, and for Cr51 in vanadium have been measured. The results are compared with other values for the Fe-Cr system, and with the various theories of diffusion in hcc metals. Some empirical correlations are discussed between Do and Q in hcc systems, or, expressed differently, the constancy of ?G*/T solidus for seveval bcc metals and alloys is noted. It appears very probable that a vacancy mechanism is operative in bcc metals, hut this cannot he stated with certainty. THE great bulk of work on diffusion in metals, both experimental and theoretical, was for many years concentrated on those with close-packed and, in particular, fcc lattices.1,2 There appears to be little doubt that the mechanism of diffusion in these solids is vacancy migration, leading to mass transfer and in substitutional solid solutions to a Kirken-dall effect.3,4 For bcc metals, the picture is much less clear. The Kirkendall effect certainly occurs in several alloys.5-10 However, attempts to understand the factors contributing to the pre-exponential in the usual expression for the diffusion coefficient D =D, exp {-Q/RT) by extension of ideas useful in close-packed lattices have not always been successful. Zener,11 Leclaire,12 and Pound, Paxton, and Bitlerl3 have suggested that various forms of ring diffusion may be important in some bcc metals. For close-packed metals, Do is usually about 1 sq cm per sec and Q - 35Tm kcal per mole (Tm = melting temperature in OK). The theory of Pound et al. suggests for ring diffusion that Do may be about 10-4 and Q, although difficult to calculate with any precision, would be significantly less than 35 T,. The experimental results on self and solute diffusion in ? uranium14,15 and ß zirconium,10 and for solutes in 0 titanium,17 and possibly for self-diffu- sion in chromium below about 0.75 T,," gave some credence to this theory. However, not all bcc materials display low values of DO and Q, and the exceptions were not predicted by any theory. Furthermore, it has recently become apparent that, in bcc materials, log D is not always linear with T-l if a sufficiently wide range of temperature is studied.16,18 This variation may be such that Q may increase18,19 or decrease20 with increasing temperature. The present work was undertaken in an attempt to provide further diffusion data on bcc metals, and to try to understand the factors which contribute to differences in behavior between the various elements. For part of this work, the Fe-Cr system was chosen since it is of considerable technological importance, and data on 12 pct Cr and 17 pct Cr alloys appeared well worthwhile to supplement that existing for the remainder of the stern.18,22 The diffusion of Fe55 in chromium was studied as an example of a more or less "normal" tracer element in a possibly abnormal host lattice. Finally, no data were available for vanadium, the neighbor of chromium in the periodic table, because of lack of a suitable isotope so cr55 was used as a tracer in a few preliminary experiments. For convenience, we shall refer to elements whose Do and Q are low compared to those predicted by Zener's theory as "anomalous". PROCEDURE This investigation determined self-diffusion rates by means of radioactive tracers and the integral-activity method first utilized by Gruzin.23 In this method a thin layer of radioisotope of the diffusing element is plated or coated onto a planar surface of the diffusion sample, which is then given an isothermal-diffusion annealing treatment. The determination of an activity-penetration curve involves measuring the residual activity of the specimen after each successive layer or section has been removed parallel to the original planar surface. The method used here is essentially the same as that used by Gondolf18 and Kunitake.21 Two radioactive tracers, cr51 and Fe55, were used in this investigation. Diffusion coefficients were determined for the diffusion of one or both of these tracers in four different materials, viz., Fe-12 wt pct Cr alloy, Fe-17 wt pct Cr alloy, chromium, and vanadium. The diffusion samples had nominal dimensions of 1.5 cm diameter and 0.5 cm thickness. The grain size was several millimeters for the Fe-Cr alloys and at least 1 mm for the chromium and vanadium samples. Accurately planar surfaces

Jan 1, 1964

By B. A. Rogers

The etching effect that is produced on a piece of polished iron or steel when it is heated in hydrogen or in a vacuum seems to have been observed first by Osmond,' who believed that he could distinguish four systems of grain boundaries on a piece of steel which had been heated in hydrogen. In a number of other investigations, samples of pure iron were found, after heating, to have complex networks in which two or three systems of grain boundaries could be detected. It was further noticed that samples that had been polished plane before being placed in the furnace were, after treatment, roughened and undulating over their entire surfaces. From a comparison of the temperature of heat treatment with that of the A3 transformation, it was concluded that the changed appearance of the samples was definitely related to the latter phenomenon. Certain other deductions were made but these are not of importance here and only observations on the appearance of the samples will be reviewed. Ewen2 heated a strip of polished iron in a vacuum in such a way that one end was maintained at a temperature of 1000" C. and the other at 580" C. On the cooler end there was outlined a simple polyhedral network, and at the hotter there appeared the complex systern of lines ant the undulating surface characteristic of iron which has passed through the A3 transformation. He found that in going from the cooler toward thc hotter end the sample maintained much the same character of surface up to the beginning of the transformed area, but that near this region doublc grain boundaries were of frequent occurrence. Rawdon and Scott concluded that the simple type of network brought out by heating a sample of pure iron in a vacuum was of the same type as that developec by ordinary etching methods. They also confirmed the observations of

Jan 1, 1929

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

THE comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined.1,2 These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. COMPOSITION AND FABRICATION OF ALLOYS The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing [ ] from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys will be referred to hereafter by their nominal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedures calculated to produce sheet 1/16 in. thick, cold-reduced by 20, 40, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from l00° to 1500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By M. G. Arthur

This paper is a theoretical analysis of fingering of water and coning of water and gas in homogeneous sand. Investigation of this idealized case illustrates the relative magnitude of the factors involved in actual conditions. The body of the report presents equations, example calculations, and charts that facilitate solution of such problems. Derivation of the equations introduced in this paper and a discussion of previously published equations are included in the appendix. Introduction Production of water from oil wells as a result of the pressure gradients established by flow of fluids through oil-~roducing sands is a common occurrence, which influences the cost of oil production, the degree of depletion and the efficiency of expulsion of oil from naturally occurring reservoirs. Control of water production and encroachment are important both in primary and secondary phases of of exploitation in order to produce oil and gas at lowest cost and in order to achieve the greatest ultimate recovery of the oil in the reservoir. Although many actual oil reservoirs present a multitude of variables that influence fingering and coning of water and gas, an inspection of the relationship and magnitude of the forces involved in the case of a homogeneous sand may indicate satisfactory methods of controlling water production. Application of equations relating the variables may indicate the geometric type of drainage that exists in a particular reservoir or in the vicinity of a particular well. A homogeneous sand body is assumed within the portion of the reservoir influenced by the well. Two geometric types of drainage are considered theoretically. The first is water fingering into an oil sand that is relatively thin compared with the lateral extent of the sand. This sand may represent the entire oil-producing reservoir or it may represent one interval in an oil reservoir, which is separated from other producing intervals by competent lithologic barriers to flow of fluids. For the condition of complete penetration of a well in such a sand body, it may be assumed that no flow occurs across bedding planes. A mathematical relation is developed between the limit of approach of a water finger to the well without being drawn into the well and the corresponding operating pressure drawdown. The second condition considered is that of water or gas entry into an oil well as the result of coning through bedding planes. The theory and graphical solution developed by Muskat' for the limit of approach of a water or gas cone to a well, without its entry into the well, related to the corresponding maximum pressure drawdown, is reviewed and amplified, Charts are presented, which facilitate graphical solution of the problem. A method is presented for the extension of this type of graphical solution to the case where gas and water coning occurs simultaneously~

Jan 1, 1944

By M. G. Arthur

This paper is a theoretical analysis of fingering of water and coning of water and gas in homogeneous sand. Investigation of this idealized case illustrates the relative magnitude of the factors involved in actual conditions. The body of the report presents equations, example calculations, and charts that facilitate solution of such problems. Derivation of the equations introduced in this paper and a discussion of previously published equations are included in the appendix. Introduction Production of water from oil wells as a result of the pressure gradients established by flow of fluids through oil-~roducing sands is a common occurrence, which influences the cost of oil production, the degree of depletion and the efficiency of expulsion of oil from naturally occurring reservoirs. Control of water production and encroachment are important both in primary and secondary phases of of exploitation in order to produce oil and gas at lowest cost and in order to achieve the greatest ultimate recovery of the oil in the reservoir. Although many actual oil reservoirs present a multitude of variables that influence fingering and coning of water and gas, an inspection of the relationship and magnitude of the forces involved in the case of a homogeneous sand may indicate satisfactory methods of controlling water production. Application of equations relating the variables may indicate the geometric type of drainage that exists in a particular reservoir or in the vicinity of a particular well. A homogeneous sand body is assumed within the portion of the reservoir influenced by the well. Two geometric types of drainage are considered theoretically. The first is water fingering into an oil sand that is relatively thin compared with the lateral extent of the sand. This sand may represent the entire oil-producing reservoir or it may represent one interval in an oil reservoir, which is separated from other producing intervals by competent lithologic barriers to flow of fluids. For the condition of complete penetration of a well in such a sand body, it may be assumed that no flow occurs across bedding planes. A mathematical relation is developed between the limit of approach of a water finger to the well without being drawn into the well and the corresponding operating pressure drawdown. The second condition considered is that of water or gas entry into an oil well as the result of coning through bedding planes. The theory and graphical solution developed by Muskat' for the limit of approach of a water or gas cone to a well, without its entry into the well, related to the corresponding maximum pressure drawdown, is reviewed and amplified, Charts are presented, which facilitate graphical solution of the problem. A method is presented for the extension of this type of graphical solution to the case where gas and water coning occurs simultaneously~

Jan 1, 1944

By L. M. Barker

THE New Cornelia Branch of the Phelps Dodge Corporation is at Ajo, Pima County, Ariz. It is at the southern terminus of the Tucson, Cornelia and Gila Bend Railroad, which connects with the Southern Pacific Railroad at Gila Bend, Ariz., approximately 43 miles to the north. HISTORY Early history of the Ajo district has been related by A. W. Allen1 and by T. A. Rickard.2 Briefly, steps looking to the large-scale development of the ore body were instituted as early as 1912. This work culminated in the equipment of the property for open-pit mining by steam shovels. Ores initially mined carried economic amounts of copper carbonates as the principal copper-bearing mineral. Treatment methods developed for the extraction of the copper content involved leaching and a 5000-ton leaching plant was constructed and placed in operation in early 1917. Description of methods and equipment employed in this plant has been given by A. A. Tobelmann and James A. Potter.3 As exhaustion of the carbonate ore body neared, and mining oper-ations exposed an adequate tonnage of sulphide ores, a 5000-ton con-centrator was constructed for their treatment. That plant has been described by H. Kenyon Burch.4 Construction was completed and the plant was placed in operation in early 1924. Changes made in the original plant to improve practices and increase production will be the subject of subsequent paragraphs of this paper.

Jan 1, 1939

By K. C. McCutcheon, John Chipman

To a very large extent the quality of a mild steel ingot is determined by the manner in which it is poured into the ingot mold and its behavior during the first few minutes after it has been poured. The formation of the solid rim of metal around the periphery of the mold, the effervescent action of the liquid steel within this solidified rim and the upward or dounward movement of the metal level are indications of what is going on beneath the surface of the liquid metal, especially at the interface at which solidification occurs. Observation of this "rimming action" enables an experienced observer to predict the thickness of the sound skin of the ingot and the location and extent of cavities or "blowholes" caused by entrapment of gases. The control of rimming action at the hands of a skillful steel pourer is a vital part of the control of quality in mild steel sheet, and the behavior of the liquid steel during the rimming period is a useful criterion of the melting and refining practices employed in the open hearth. The behavior of rimming steel during solidification depends primarily upon the evolution of gases from the molten metal and it is therefore a problem of considerable interest to determine the nature and amount of the gases evolved. A number of attempts to determine either the amount or the analysis of the evolved gases have been reported. Klinger,' in 1925, analyzed the gases extracted from rimming, sernikilled and killed steel ingots and found that the chief constituent of the rimmining gas was carbon monoxide. The relatively large amounts of nitrogen reported in his first few samples may have been due to incomplete removal of air from the gas-collecting mechanism. McKune² reported similar studies of rimming ingots from which surprisingly large proportions of nitrogen and hydrogen were evolved. Ameen and Willners3 determined both the amount and composition of gases extracted from unkilled ingots with the aid of diminished pressure. Their ingots weighed only 80 kg. (176 lb.) and apparently were solid within two or three minutes, so that their

Jan 1, 1938

By John Chipman, K. C. McCutcheon

To a very large extent the quality of a mild steel ingot is determined by the manner in which it is poured into the ingot mold and its behavior during the first few minutes after it has been poured. The formation of the solid rim of metal around the periphery of the mold, the effervescent action of the liquid steel within this solidified rim and the upward or dounward movement of the metal level are indications of what is going on beneath the surface of the liquid metal, especially at the interface at which solidification occurs. Observation of this "rimming action" enables an experienced observer to predict the thickness of the sound skin of the ingot and the location and extent of cavities or "blowholes" caused by entrapment of gases. The control of rimming action at the hands of a skillful steel pourer is a vital part of the control of quality in mild steel sheet, and the behavior of the liquid steel during the rimming period is a useful criterion of the melting and refining practices employed in the open hearth. The behavior of rimming steel during solidification depends primarily upon the evolution of gases from the molten metal and it is therefore a problem of considerable interest to determine the nature and amount of the gases evolved. A number of attempts to determine either the amount or the analysis of the evolved gases have been reported. Klinger,' in 1925, analyzed the gases extracted from rimming, sernikilled and killed steel ingots and found that the chief constituent of the rimmining gas was carbon monoxide. The relatively large amounts of nitrogen reported in his first few samples may have been due to incomplete removal of air from the gas-collecting mechanism. McKune² reported similar studies of rimming ingots from which surprisingly large proportions of nitrogen and hydrogen were evolved. Ameen and Willners3 determined both the amount and composition of gases extracted from unkilled ingots with the aid of diminished pressure. Their ingots weighed only 80 kg. (176 lb.) and apparently were solid within two or three minutes, so that their

Jan 1, 1938

By M. Mathieu

The Rove tunnel is the means by which the canal from Marseilles to the Rhone Riverl penetrates the hills of Nerthe, lying between Mar- seilles harbor and Lake Berre, Fig. 1. The canal will communicate at sea level with both terminals. The original project planned a lock near the village of Marignane; but observations, pursued for more than three years, showed that the water surface gradient would average only 0.015

Jan 1, 1923

By M. Mathieu

The Rove tunnel is the means by which the canal from Marseilles to the Rhone Riverl penetrates the hills of Nerthe, lying between Mar- seilles harbor and Lake Berre, Fig. 1. The canal will communicate at sea level with both terminals. The original project planned a lock near the village of Marignane; but observations, pursued for more than three years, showed that the water surface gradient would average only 0.015

Jan 1, 1923

By Robert Glass Cleland

THE BEGINNING of a large enterprise is often as in- significant as a lump of leaven hidden in a bowl of meal or a handful of mustard seed that the wind blows across a field. In 1950 the company known today as the Phelps Dodge Corporation had nearly thirty-two thousand stockholders, paid salaries and wages of about fifty million dollars to some thirteen thousand persons, produced nearly four hundred and ninety million pounds of copper, and possessed net current assets of approximately one hundred and six million dollars. For the origin of this great business, one must go back approximately a hundred and fifty years to an obscure saddle-making shop in the small town of Hart- ford, Connecticut. Anson Greene Phelps, proprietor of the shop and master saddler in his own right, was born in 1781-the year of the Battle of Yorktown, the surrender of Cornwallis, and the close of the Revolutionary War Anson's forebears had come to America in the great Puritan migration that left fields, shops, pulpits, and hearthstones in the reign of Charles the First to transplant the strong, tough roots of their race, culture, and institutions in the New World.

Jan 1, 1952

By Hiroshi Oikawa, R. G. Blake, A. G. Guy

An equatzon has been derivedfor conveniently calculatzng the couvse of homogenzzation in a three-corviDonent solid solutiorz. The necessary assumptions are that the initial distributions of concentration are sinusoidal and that the four interdiffusion coefficients are constant. Employed in the deriuation were the Laplace transform and the fouter Fourier sine transfovwz. The final equation is shown to be in good agveetnent with the experimental results of Kirkaldyet al. on Cu-Sn-Zn alloys. COMMON boundary conditions for representing physical problems are those of the finite solid and of the infinite solid. Many metallurgical phenomena, however, have the geometrical form of a finite pattern reproduced throughout an infinite solid. Precipitation within a uniform matrix and segregation during solidification are examples. The purpose of this treatment is to show that a convenient and useful mathematical analysis is possible in those cases in which the finite pattern can be approximated by a sine function. The particular topic to be considered here is the elimination of segregation by diffusion, but the mathematical model has applicability in many other areas. It should be recalled that the mathematical solution of a typical problem involving a finite solid, such as diffusion into a thin layer, is quite involved.' Various types of solutions are used depending on the degree of advancement of the diffusion process and on the initial conditions. A step function is the simplest initial condition, but even in this case the general solution has the form of an infinite series. Kirkaldy et a1.2 have

Jan 1, 1968

By J. B. Davis

This paper has been prepared at the suggestion of Mr. Dunbar D. Scott, to supplement his " Evolution of Mine-Surveying Instruments."† Before entering into a detailed history of solar instruments, a few remarks will be made touching upon land-surveys in general, and on what has led to the development of these instruments.The oxidation of metals melted in contact with air takes place with dissimilar results. Tin, lead or zinc are examples of a class, the oxides of which float on the surface of the melted metal. First a film is produced, which covers the surface; then, if agitation from any cause exposes new metal to the action of the air, additional oxidation takes place, and the film is increased in volume. This change goes on until a considerable quantity of oxide (or " dross," as it is technically called) is formed; depending, of course, upon the duration of the exposure of the metal to the atmosphere. When such metals are poured, the dross may be skimmed off; and clean metal will be left underneath. The removal of such oxides is, therefore, merely a mechanical process. In the case of copper, however, the result is quite different. The sub-oxide of copper (Cu2O) is readily soluble in molten copper; and therefore, instead of the formation of a film of oxide, to be finally removed as dross, the surface of the metal remains bright and clear, because the oxide has been dissolved as soon as it was produced. It is customary in the process of copper-refining to leave a small quantity of oxide in the metal, in order to oxidize any traces of bismuth, arsenic or antimony which have not been entirely removed. As a result, these metals exist in the commercial product as oxides, and not as metals, which would form an

Jan 1, 1901

By F. W. Bremmer

The experiments described in this paper constitute the preliminary work of an investigation outlined to determine the combined effects of steam and temperature on the endurance properties of certain steels. Essentially of a fundamental nature, it was found necessary, in order to make the investigation comprehensive, to test materials treated to give a wide range of properties. The work reported deals chiefly with nickel steel with one series of tests including nitriding steel. Such a study involves numerous variables, and requires an endurance-testing machine of rather special design. Testing Machines The testing machines used were designed by C. E. Weaver;l they are a modification of the White-Souther and McAdam types. Each was driven directly by an individual 1/2-hp. 115-volt direct-current motor, running at a speed of 2200 r.p.m. Fig. 1 shows the assembly drawing and Fig. 2, a photograph of one of the machines. Specimen B is held by the rotating specimen holder A inside the steam box F, which is closed at the top by a tight-fitting, elliptical cover G. The load is applied to the specimen through the rod D and bearing C. E is an oil pipe leading fromthe lubrication system to the bearing C. The steam, which comes from the power house, is admitted through an inlet (not shown in Fig. 1) at the side of the box, the drain being at the bottom. Steam packings were placed around the rod D and the rotating shaft at H, from which the water was drained by means of a vacuum, which usually showed a gage reading of about 10 in. The temperature was measured by a mercury thermometer, and the pressure by a steam gage. Method of Applying Load After the motor has been started and the specimen as a consequence put in rotation, the load is applied by placing the foot pedal A (Fig. 2) in contact with electromagnet B, the winding of which is connected electrically in series with the motor. This operation releases the support under the weights that constitute the load. By this means the load

Jan 1, 1930

By H. L. Barr

THE following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geol-ogists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions.

Jan 1, 1940

By C. H. Mathewson

Discussion of the paper of C. H. MATHEWSON and ARTHUR PHILLIPS, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1916, pp. 1 to 50. ZAY JEFFRIES, Cleveland, Ohio (communication to the Secretary*).¬The authors are to be congratulated for this interesting and valuable contribution. The paper as a whole shows very careful experimentation coupled with rare judgment in drawing conclusions. I have been working along similar lines for the last two years with other metals and alloys. In a short conversation with Dr. Mathewson about July 1, 1915, he mentioned the fact that different degrees of cold work greatly affect the temperature of recrystallization on annealing, Later I determined the recrystallization temperatures of iron, mild steel, and copper, with different degrees of cold work and found that the greater the degree of cold work, the lower the temperature of recrystallization on annealing. In the course of these experiments, I conceived practically the same ideas regarding the reasons for recrystallization as those advanced in the article under discussion. After a metal has been reduced by cold work to about one-fourth of its original area, the differences in orientation of different parts of a given grain can be seen plainly at a magnification of about 1,000 diameters. It is interesting to note that in Fig. A, Plate I, the lines of deformation are not parallel. For example,. in the large grain at the lower left corner of the micrograph, if the lines of deformation about 3g in. from the left edge are continued in a straight line, this line will intersect a straight line drawn as a continuation of the lines of deformation on the extreme right of the grain, at an angle of about 20°. Similarly, if the lines of deformation at the extremities of the large grain in the right central portion of the micrograph are extended, the lines intersect at an angle of about 35°. The individual lines of deformation are not straight. In some of these the parts of the broken lines intersect at angles as great as 15°.

Jan 5, 1916

By T. H. Aldrich

The Aldrich Mining Go. holds under lease from the Illinois Central R. R. Co. about 14,000 acres, in the east half of Township 12, Range 12 W., in Marion county, Alabama, and owns other lands, of which about 1,000 acres adjoin this leased tract, making a total area of about 15,000 acres, all of which is underlain by the coal-seam upon which the company is operating. This seam is nearly horizontal; and a ravine, diagonally crossing the tract, exposes the outcrop on either side for about 2 miles. The territory has been so divided that nearly the whole of it can be worked out by two collieries. The mines at Brilliant were opened in the fall of 1898, and shipments began in the following spring. The original plan was to furnish steam-coal for locomotives to the Illinois Central R. R. Co.; and upon this expectation the investment of capital was made. The field was entirely new; and the softness of the coal at the outcrop induced the belief that it could be very cheaply mined. A contract for the delivery of a large quantity of coal to the railroad was accordingly executed. But with the advance of' the entries to increasing distances from the outcrop, the coal proved so hard that it could no longer be drilled with a breast-auger; and the expense of mining became so great that the contract for cheap steam-coal had to be canceled. It became evident that the work must be done with machinery and explosives, if it could be profitably done at all. On the other hand, the excellent quality of this coal opened, at the same time, a possible market not specially contemplated at the outset—namely, that of a first-rate coal for domestic and general uses. Since no other deposit of such coal was known to exist on the line of the Illinois Central, or any other railroad

Jan 1, 1907

By D. M. Given

HOW much can the mine operator afford to spend on his coal burning boiler plant? The usual answer is as little as possible and still get the job done. Thus, attention must be focused on the spot where excessive costs are most likely to arise - the materials handling end of the job. Boiler plants consuming less than 30,000 tons of coal annually can be controlled to the point where costs for handling coal and ashes are under $1.00 per ton. There is a wide selection of coal and ash-handling systems that can be used in smaller boiler plants to provide labor savings and convenience required if management is to accept coal as fuel.

Jan 7, 1953