Search Documents

By E. C. Harder

In view of the gradually decreasing known reserves of high-grade manganese ore and the rapidly increasing consumption of iron-manganese alloys in the steel industry, it is well to turn our attention to the development of low-grade manganiferous ore deposits and to the utilization of these ores in steel manufacture. The dependence of this country on imported manganese ore and ferromanganese has been forcibly brought to the attention of steel makers during the last few years by the cessation of manganese-ore imports from Russia, the restriction of manganese-ore imports from India and of ferromanganese imports from Europe. Should the importation of manganese ore from Biazil cease, the steel industry of this country would face a serious situation. The present practice of steel making requires ferromanganese in large quantities and ferromanganese of the grade used at present can be produced only from high-grade manganese ores such as the United States appears to possess only in insignificant amounts. There are in the United States, however, large reserves of manganiferous iron ore which could probably be used extensively in the steel industry if certain changes in the practice of steel manufacture were made. Thus high-grade manganese ore could be conserved. Among the most important deposits of manganiferous iron ore in this couniry are those of the Cuyuna iron-ore district of Minnesota. It is probable that in case of restriction of foreign supplies, the users of manganese in the United States would have to rely to a large extent on the Cuyuna district to make up the shortage. Manganiferous iron ore was found in association with iron ore in the Cuyuna district in many of the early drilling operations and the possibility of its utilization was in the minds of various explorers in the dis-

Jan 1, 1918

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-'. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.' For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-'. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.' For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.' When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.' When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By I. J. Demer, M. L. Holzworth, J. C. Kremer, P. A. Beck

For alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystal-lization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig I shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hr. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b It is seen that for any annealing temperature below T, the grain size was smaller than. in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T, the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig I by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has been most frequently and best investigated in brass. This type has been designated as "normal grain growth,'' while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1949

By L. A. Geoffrion, R. H. Perkins, J. C. Biery

Densities of cerium metal and several lour-melting binary cerium alloys were measured over the range 25° to 800°C. A rolumeter, using NaK as working fluid, was used to obtain the data. The cerium, Ce-Co, Ce-Ni, and Ce-Cu alloys all exhibited an increase in density on melting, while a Ce-Mn alloy expanded on melting. FOR the proper design of a nuclear reactor, the change in density of the fuel with temperature must be known. This is especially important in a system utilizing molten fuel, such as LAMPRE (Los Alamos Molten Plutonium Reactor Experiment), since a relatively large change in density usually occurs during the solid-liquid transition. The fuel for LAMPRE is a Pu-2.5 wt pct Fe alloy with a melting temperature of 410°C. However, limitations in reactor design with this fuel have led to consideration of other plutonium-containing alloys for use in future generations of this type of reactor. Several ternary alloys containing plutonium and cerium as two components have satisfactorily low melting points. The system that at the present time appears to be most acceptable is Pu-Ce-Co; it exhibits little change in melting temperature with wide variation in plutonium concentration. Other alloys that have received some consideration contain nickel, copper, and manganese as the third constituent. The proposed fuel alloys are difficult to handle experimentally in the 25" to 800°C temperature range since they oxidize readily, react with many solvents, and contain a poisonous fissionable material. In addition, in this temperature range the alloys pass through the solid-liquid transition. Several techniques are available for measuring the densities and volume coefficients of expansion of solids or liquids. However, the only apparatus that appears suitable for measuring expansion coefficients over this temperature range and through the phase transition is a volumeter. In a volumeter, the indicating medium must be essentially inert to and insoluble in the material being studied. It must also possess a low vapor pressure over the operating temperature range, and its coefficient of expansion must be accurately known. One material that is satisfactory in nearly all of these respects is the alloy Na-78 wt pct K, which melts at -10°C and has a vapor pressure of 860 mm Hg at 800°C. This relatively high vapor pressure at 800°C requires an overpressure of an inert gas to prevent boiling. While a volumeter is capable of determining accurately the volume coefficients of expansion of materials, it cannot be used for absolute density measurements. Therefore, a density determination at a known temperature must be coupled with the volumeter measurements to give all the desired data. The weight-loss technique using immersion in bromobenzene at room temperature proved to be satisfactory. The preliminary work that was done on this experimental program involved developing and calibrating the equipment, and measuring the densities and volume coefficients of expansion of cerium and some low-melting binary cerium alloys. The complications that are caused with the introduction of plutonium into the system were avoided until the equipment was proved to be satisfactory and until experience was gained in its operation. It is this first phase of the experimental work that is described in this report. DESCRIPTION OF EQUIPMENT AND OPERATING PROCEDURE The NaK volumeter is shown schematically in Fig. 1. Basically, the equipment consists of two weld-sealed stainless-steel containers of nearly identical volume. One container holds a tantalum crucible and the specimen being measured; the other contains a tantalum crucible and a tantalum specimen used as a control reference material. To avoid temperature gradients, the bombs are located in a copper block inside the furnace. Stainless-steel capillaries of equal length and volume connect each stainless-steel container to a glass viewing capillary. The stainless-steel containers, stainless-steel capillaries, and a portion of the glass capillaries are filled with NaK (22 wt pct Na-78 wt pct K). The NaK/gas interface in the glass capillary is viewed with a cathetometer which is accurate to *0.5 mm. The cathetometer readings are used to calculate the volume changes of the samples during a run. This volumeter is basically the same as that described by F. Knight in Plutonium 1960. 2 However, changes in equipment design and operating procedure were made to eliminate some major operating difficulties. These changes are summarized below. 1) In filling the manometer with NaK, gas was frequently entrained in the system. Evacuation of the system before filling failed to eliminate the en-

Jan 1, 1965

By S. F. Emmons

It was said by many who discussed Professor Posepny's admirable paper on the "Genesis of Ore-Deposits," read at the Chicago meeting of the Institute, in 1893, that its most valuable feature was the clear distinction which it drew between the influence upon ore-deposits of the " vadose " circulation of waters descending directly from the surface, and that of the deep underground circulation of waters generally coming from the depths, and assumed by the author to be ascending through more or less open spaces under the influence of heat. A little later the effect of the oxidizing action of the vadose circulation upon ore-deposits was ably and exhaustively treated by Prof. R. A. F. Penrose, in a paper on " The Superficial Alteration of

Jan 1, 1901

By Hsun Hu

The microstructural changes during rolling and at various stages of recrystallization in (111)[112] oriented single crystals of Si-Fe have been studied by transmission electron microscopy. At very low deformation, the dislocation structure consists of jogged dislocation lines, edge dislocation dipoles, and numerous dislocation loops, which may be interpreted by the jog-formation mechanism in moving screw dislocations. Up to 70 pct rolling reduction, no sharply defined cells are formed. Subgrain forma- tion takes place somewhat earlier in the annealing process than in a similarly processed (110)[001] crystal. This may be partly responsible for the reported difference in the rate of recrystallization between (111)[112] and (110)[001] crystals. Evidence indicates that the formation of recrystallization nuclei occurs largely by the coalescence of sub -grains. This is consistent with previous observations on other Si-Fe crystals. AVAILABLE data in the literature indicate that the main features of rolling and annealing textures in (111)[112] and (110)[001] crystals are essentially similar. A (111)[112] or (111)[112] crystal can be rolled 70 pct without changing its initial orienta-

Jan 1, 1964

By H. W. Young

DEVELOPMENT of high-tension outdoor substations during the past few years has been due primarily to economic reasons. The demand for power in small communities could not be met with the conventional and 1 FIG. 1.-33,000-VOLT STEP-UP OUTDOOR AIR-BREAK SWITCH AND SUBSTATION INSTALLATION OUTSIDE OF A POWERHOUSE GENERATING AT 2300 VOLTS STEPPING UP TO 33,000. TWENTY-ONE COAL MINES ARE SUPPLIED FROM LINES LEADING FROM THIS INSTALLATION. comparatively expensive indoor types unless the rate for service was materially increased. That the various problems incident to development have been solved successfully, it is only necessary to point to the

Jan 9, 1919

By Robert Gilman Brown

The original power-plant of the Standard Company has been described* by Mr. T. H. Leggett, late president and manager of the company; but since the presentation of his paper considerable additions have been made, which will be found interesting because of the engineering features involved and of the attainment of a high degree of flexibility with the inflexible, two-wire, alternating system of electrical transmission. Although these additions have been completed during the last year, they constitute, to a large extent, only the carrying out of plans that belonged to the original conception of the installation. The regular operation of the water-power through the winter proved very difficult; there was a considerable length of ditch to be kept open, and, as the stream is small and any freezing night may stop the whole flow of water, there was the .additional trouble of having no reserve to draw upon. The rule for the winter is, that after a night of hard frost water begins to move in the canon before noon on all but the coldest days. To obviate the nuisance of the anchor-ice, and to make available all of the water, a dam of sufficient height to impound several days' run of water has been built across the canon, 3875 feet above the power-house, and provided with pressurepipe well below the surface. In place of the 1571 feet of pipeline from penstock to power-house, there has been substituted a line 3875 feet long to bring water direct from the dam. The dam is of logs, cribbed up in squares of about 12 feet, ballasted with earth and rock and sheathed on the water-face with 3-inch plank.

Jan 1, 1897

By G. P. Conard, E. H. Rennhack

The generation of fibers composed of individual TiZn15 compound particles and their influence on crystallographic orientation in chill-cast, hot-rolled hypoentectic Zn-Ti alloys were explored. Metallo-graphic examination and X-ray diffraction data show that such fibers form a planar network after 50 pet reduction which eventually tends to suppress twinning at some critical reduction level (-90 pct) where the grain size approaches the interfiber, spacing. This leads to the development of a duplex-type projerred orientation through slip rotation consisting of an al-most ideal (0001)(2iiOj texture and a (0001) (1010) rotated component. Correlations between basal-plane rotation and secondary- creep rc11e sugg-est, however that prejerred orientation does not contribute in a major way to the creep resistance of these alloys. EFFORTS to improve the creep resistance of zinc through alloying without incurring a loss in fabricating properties have achieved only minor success with the exception of the very effective addition of titanium. Anderson, Boyle, and Ramsey,l for example, demonstrated that increasing the amount of thiselement from 0.05 to 0.23 wt pct produced a progressive, 45-fold increase in the inverse creep rate of hot-rolled

Jan 1, 1967

By R. L. Dalton, L. A. Rapoport, C. W. Carpenter

Procedures have been developed to study the performance characteristics of unconfined pilot water floods using scaled laboratory models. The effects of operating conditions on pilot performance for variozrs well patterns have been investigated. The limitations of the laboratory model studies are outlined. Relationships between the oil recoveries of pilots and large-scale floods have been established. The applications of model studies to the prediction of large-scale waterflood performance and pilot flood design are discussed. INTRODUCTION Pilot water floods are undertaken to evaluate operational procedures and to gain advance information about the performance of an extensive water flood. In general, however, the performance of a pilot flood is not directly indicative of what can be expected from a large-scale pattern water flood. This difference stems from the fact that the over-all flow configurations are not the same for the two systems. A water flood normally consists of an array of identical well patterns. In such an array, the perimeters of the well patterns are axes of symmetry and act as impermeable boundaries. Thus, an extensive, pattern water flood can be visualized as a repetition of "confined" floods. In contrast, a pilot water flood involving only one or a few well patterns is "unconfined". Here the well patterns are not balanced by other flood units; hence, the perimeter of the pilot area does not act as an effective boundary. Accordingly, only a portion of the fluids injected (and also of those originally contained within the pilot area) is captured by the producers of the pilot. The rest escapes into the surrounding reservoir. This usually causes the amounts of oil and water produced in the pilot to be different from those recovered by a producer in an extensive water flood. Moreover, the recovery observed in the pilot can be expected to be greatly influenced by operating conditions, i.e., by the bottom-hole pressures at the injection and producing wells. The above considerations show that full utilization of pilot test results and reliable prediction of large- scale water floods require a knowledge of the relationship between the recovery performance of confined and unconfined well patterns. To date, only limited basic information is available on the behavior of pilot water floods. Craig, et al,' have investigated the effects of initial gas saturation, oil-to-water mobility ratio, and well damage on the oil recovered from a single, "normal" five-spot pilot pattern (Fig. 1). Rosenbaum and Matthews2 studied the effect of initial gas saturation and mobility ratio on the ratio of production rate to injection rate for various groupings of five-spot patterns. Paulse113 investigated the effect of mobility ratio and distance from the pilot to the edge of the reservoir on the areal sweep in a single "inverted" five-spot (Fig. 1). However, none of these studies considered the effect of operating conditions on pilot flood behavior. Moreover, hardly any of the work to date dealt explicitly with the oil-recovery performance of the pilot floods. The purpose of this paper is to introduce the concept of interrelation between pilot flood behavior and operating conditions, to illustrate this interrelation by means of experimental data and to compare the recovery performances of dif-

By Paul A. Bailly

2.1-1. The Exploration Function in the Mineral Industry. With regard to a new mine, exploration can be technologically defined as all the activities and evaluations necessary before an intelligent decision can be made establishing size, initial flowsheet, and annual output of the new extractive operation based on a certain mineral deposit. The activities that follow such a decision are called first development, then operation (90). Thus, in the U.S.A., exploration may continue in the technological sense after a mineral property has entered the "development stage" as defined for tax purposes. Regulations under Sections 1.615.1 and 1.616.1 of the U.S. Internal Revenue Code state that the "development stage" has been reached when "deposits of ore or other minerals are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation by the taxpayer" (95). There are, of course, many instances where additional later exploration discloses additional reserves which justify a plant much larger, more efficient and more profitable than the minimum feasible commercial operation. After a surface mine is put into operation, additional search generally will increase the reserves and thus warrant expansion of the rate of output and/or extend the life of the operation. The methods and techniques in such search are similar to those used in predevelopment exploration. This activity has produced a major part of new reserves for all mineral commodities but is not considered as exploration in the context of this chapter. The objective of exploration is, briefly stated, to find and acquire a maximum number of new economic mineral deposits with a minimum cost and in minimum time. The search must be so organized as to maximize the overall probability of discovering commercial mineral concentrations within a minimum time with the funds available. As shown by Celasun (27) these statements are neither adequate nor complete from a pragmatic point of view. Each actual exploration venture must define its objectives in terms of a minimum rate of return on investment for any deposit found

Jan 1, 1968

By W. M. Peirce

ON May 16, 1871, twenty-two men met in Wilkes-Barre, Pennsylvania, and founded the American Institute of Mining Engineers.* If we could transport ourselves back to that year and survey the state of science and technology in general, and, in particular, the field of our immediate interest-nonferrous metals-we would feel a justifiable pride in what had been accomplished up to that time. These accomplishments in the metal field were at the moment in the process of documentation by an Englishman, J. A. Phillips, in a new 700-page edition of his book to be published in 1874 under the title of "Elements of Metallurgy." True, looking over his shoulder, we would smile to read that "all metals are capable of assuming a crystalline form under favorable conditions," and that tensile testing is done "by adding weights to a firmly suspended wire until it fractures," and we would find only three pages on aluminum and none on magnesium. We would, however, find an astonishing wealth of detailed knowledge on iron and steel and the then common nonferrous metals and alloys such as brass and bronze. But if we possessed a little prophetic vision as we directed our attention to the short period that had elapsed since the close of the Civil War, we

Jan 1, 1947

By J. G. Richardson, J. W. Graham

The purpose of this paper is to present the results of theoretical and experimental studies of water imbibition. The imbibition processes are involved in recovery of oil from stratified and fractured-matrix formations in natural water drives and water flooding. An understanding of the role of inhibition in implementing the recovery of oil from such formations is deemed essential to proper control of these reservoirs to achieve maximum recovery. The theoretical studies involved development of the differential equations which describe the spontaneous imbibition of water by an oil-saturated rock. The dependence of the rate of water intake by the rock on the permeability, interfacial tension, contact angles, fluid viscosities and fluid saturatiorls is discussed. A few experiments were performed using core samples to determine the effects of core length and presence of a free gas suturation. The role of water imbibition in recovery of oil from a fractured-matrix reservoir by water flooding was investigated by use of a laboratory model. This model was scaled to represent one element of a frac-tured-matrix formation. Water floods were made at various rates with several fracture widths. Interpretations were made of the behavior expected in a system containing many matrix blocks. The presence of a free gas sntu.ration was found to reduce the rate of water imbibition. In the reservoir prototype of the fractured-matrix model, water imbibition rather than direct displacement by water was the dominant mechanism in the recovery of oil at low rates. INTRODUCTION Imbibition may be defined as the spontaneous taking up of a liquid by a porous solid. The spontaneous process of imbibition occurs when the fuid-filled solid is immersed or brought in contact with another fluid which preferentially wets the solid. In the process of wetting and flowing into the solid, the imbibing fluid displaces the non-wetting resident fluid. Common examples of this phenomenon are dry bricks soaking up water and expelling air, a blotter soaking up ink and expelling air and reservoir rock soaking up water and expelling oil. As increasingly better lithological descriptions have been made of the characteristics of petroleum-bearing formations, it has become obvious that imbibition phenomena which were once considered laboratory curiosities are of practical importance. For instance, in reservoirs composed of water-wet sand strata of different permeability in intimate contact, the tendency of water to channel through the more permeable stratum is offset by the tendency for water to imbibe into the tight sand and expel oil into the coarse sand. Also, in fractured-matrix formations the tendency of water to channel through the fractures is offset by water-wet matrix blocks. As some imbibition of the water into the of the largest fields in the world are fractured-matrix reservoirs, it has become increasingly important to understand all the factors involved in the imbibition process. Examples of fractured-matrix reservoirs are the Spraberry field in West Texas which produces from a fractured sandstone', the giant Kirkuk field in Iran', the Dukhan field in Qatar, Persian Gulf2, and the Masjid-I-Sula-main and the Haft-Kel fields in Southwestern Iran, which produce from fissured limestone3. Research into recovery of oil from fractured-matrix formations was stimulated by the rapid decline of oil productivity of wells in the Spraberry formation. One result of this research was the water imbibition process developed by the Atlantic Refining Co.4 Another idea was that much of the Spraberry oil could be recovered by conventional water-flooding procedures5. Subsequently, pilot floods were conducted in this field to test the feasibility of these ideas. It was felt that an understanding of the role played by imbibition processes in displacement of oil from a fractured-matrix reservoir could not be obtained from field data alone because of the many complicating factors and uncertainties involved. Therefore, theoretical and laboratory studies were undertaken to provide this understanding. Study of the equations which describe the linear, countercurrent imbibition process provided an insight into the role of various factors in the process, such as the permeability of rock and inter-facial tension. In addition to the theoretical studies, imbibition experiments were conducted with core samples to determine the effect on the rate of imbibition of such variables as core length and free gas saturation. The principal experimental studies were conducted by water flooding a scaled model of an clement of a frac-tu red-matrix reservoir to evaluate

By D. J. McAdam

IN a recent survey of the literature, the author has found evidence incompatible with prevalent views regarding the technical cohesive strength and yield strength of metals. Some of the evidence regarding the technical cohesive strength was presented in a previous paper,21 and views were presented that are believed to be in better accord with the evidence. In that paper, it was shown that the technical cohesion limit (contrary to prevalent views) varies with the combination of principal stresses,† and that the influence of plastic deformation on the technical cohesive strength is not in accordance with prevalent views. In this paper, consideration will be given to both the technical cohesion limit and the yield stress as affected by the combination of principal stresses. Evidence will be presented that the variations of the yield stress and the technical cohesion limit with the combination of principal stresses are not in accordance with prevalent views. Consideration will also be given to ductility and work-hardening capacity, which depend on the initial difference between the technical cohesion limit and the yield stress. By the "technical cohesion limit" is meant the mean stress at actual or potential* fracture. An example of a technical cohesion limit is the "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture. The cohesion limit thus obtained for a ductile metal, however, has been greatly altered by the plastic deformation. It is important to consider the cohesion limit of the metal prior to this deformation, and the variation of the cohesive strength with plastic deformation. The relation between the cohesion limit and the corresponding flow stress† determines the ductility of a metal and the energy that it will absorb before fracture. In this paper, as in the previous paper,21 tensile stresses will be viewed as positive and compressive stresses as negative. The algebraically greatest principal stress will be designated S1, the least principal stress will be designated S3, and the intermediate principal stress will be designated S2. In the previous paper, attention was confined to stress combinations with two of the principal stresses equal (with the intermediate principal stress S2 equal either to S3 or S1). In this paper, consideration will also be given to the effect of stress combinations with all three principal stresses unequal. In the earlier sections of the paper (pp. 1 to 14), attention will be confined to stress combinations with

Jan 1, 1942

By W. C. McBee, B. W. Jong, T. A. Sullivan

A sulfur concrete technology has been developed by the US Bureau of Mines, where chemically modified sulfur is used with suitable mineral aggregates to produce construction materials that are resistant to corrosion by acids and salts. This report presents a summary of the basic technology and results of testing the materials under actual operating conditions in 50 corrosive environments in 40 commercial plants. After four years of testing, there was essentially no evidence of material degradation or loss of strength. Regular concrete materials were attacked and, in some cases, completely destroyed under the same conditions. Testing is continuing to establish ultimate longevity and durability of the sulfur concretes. The materials are finding widespread applications in metallurgical, chemical, and fertilizer processing plants.

Jan 1, 1986

FEW whose good fortune it has been to gaze on the Utah Copper mine but will agree that it is one of the two or three most magnificent man-made spectacles in the world. Skyscrapered Manhattan Island perhaps is more inspiring; but there the effect is obtained by aggregating a thousand separate units. The Utah mine is a single thing- the biggest thing that men have made. By the end of 1931 there had been moved at Utah 222,000,000 cu. yd. of material, including ore and the waste rock that overlay it. This figure will be increased at an average rate of nearly 20,000,000 yd. per year. Excavations for the Panama Canal are estimated at 232,300,000 cu. yd., but the Canal is 50 miles long, and it is impossible to obtain a comprehensive view of the whole project at one time. The spectator, on the other hand, need only walk part way up the east slope of Bingham Canyon to see unfolded before him the whole panorama of the great copper mine. In the foreground is a huge pit bottomed for the time being 100 ft. below the normal floor of the canyon, which also is the elevation of the main railroad yard. Here from 500 to 800 standard steel railway cars, each of 80-ton capacity, are assembled daily to carry the ore to the concentrators. But the main part of the mine and that from which ore is now coming lies above this level. As can be seen in the accompanying photograph, a series of terraces or benches reaches to the top of the mountain that projects between the main branch of Bingham Canyon and Carr Fork. From bench A (the yard level) to bench W is a vertical distance of 1500 ft. In height the benches vary from 40 to 70 ft. and in width from 30 to 450 ft. The lower benches, as they skirt the mountain,

Jan 1, 1933

By Sidney H. Loram

As the work carried on by this Company, of which the writer has been in charge for the past two years, is somewhat unique, the following account of it may be of interest, and, on that account, is offered to the Institute without any attempt to claim this practice as the best. Mines. The mines supplying ore to the Company arc situated in three groups: the Guanaco field,.about 80 miles N.E. of the port of Taltal (lat. 25" S., long. 70" 30' W. of Greenwich); the Sierra Overa, about 63 miles S.W. of Taltal; and Paranao, about 42 miles due N. of Taltal (12 miles N. of the small town of Paposo, once famous for its copper-output). Guanaco. This field lies in the center of an absolutely waterless mountainous desert, where not a sign of vegetation can be found for miles. The dryness is such that ivory and horn crack and open, while raw-hide must be used in place of leather, which -would become worthless in a very short time. Water is brought about 21 miles by piping from the Cordillera, but only in small quantities, and costs in the Guanaco $7 (= $1.78 gold) per cubic meter. All supplies and food are sent from the port of Taltal, which in turn draws its supplies from the south of Chile, the

Jan 1, 1900