Search Documents

By R. A. Salathiel, A. D. Kaiser, P. H. Monaghan, B. E. Morgan

The productivities of many hydrocarbon-bearing for-rnntions appear to be reduced during drilling, completing and repairing operations. The reason for these othcarwise unexplainable low productivities may be a drastic reduction of formation permeability immediately surrounding the borehole. A possible cause of the reduced permeability is swelling and dispersion of clays present in porous media when contacted by fresh water or mud filtrates. Hence, the invasion of fresh water or mud filtrate into hydrocarbon-bearing formations that contain clays may cause low productivities as a result of formation damage. Present laboratory investigations have yielded results which supplement existing literature on formation damage. An expanded-type clay, montmorillonite, way found in hydrocarbon-bearing formations not previously analyzed. When sand columns and formation cores containing montmorillonite were contacted by fresh water, their oil permeabilities were reduced. This reduction in oil permeability way restored partially but not completely by a repair procedure, i.e., flooding with kerosene containing organic agents or flooding with water containing electrolytes. Hence, where montmorillonite is present in formations, prevention of formation danzage was indicated to be the only complete solution to the problem. To prevernt formation damage, results suggested use of an approximately 1 per cent solution of calcium chloride or stronger solutions of sodium or potassium chloride. In conventional rotary drilling operations the wall of the hole is exposed to drilling mud for days, weeks, and in some instances for as long as several months. During this time, drilling mud filtrate seeps slowly into formations surrounding the hole. The permeability and stability of many formations, especially those containing clayey materials, are impaired by the mud filtrate. Often interaction between the mud filtrate and the formation causes drilling and production difficulties. Serious reduction in productivity of oil and gas formations during drilling, completing and repairing wells has been noted often in recent years. Cases are known of development wells which produced only small volumes of fluid upon completion. However, after a period had elapsed, they began to produce oil or gas in commercial quantities. In other cases, results of drill-stem tests taken during the drilling of deep wells have indicated good production should be obtained from shallow formations. Later difficulty has been experienced in obtaining production from these shallow formations which had remained in contact with drilling muds for an extended time. In yet other cases wells have failed to attain the productivities expected from previous performance after the use of drilling mud as a circulating fluid during workover operations. It is evident from the field behavior cited that the productivities of certain oil- and gas-bearing formations have been damaged by exposure to drilling muds. This reduction in well productivity, called "formation damage", causes serious consequences. In development wells, expensive remedial operations are incurred. In wildcat wells, good formations may appear to be marginal or even non-productive. The importance of formation damage has been recognized by a number of investigators1-s who have considered the effects of fresh water, saline solutions and aqueous mud filtrates on the permeabilities of formations. A general conclusion from such studies is that interaction between water and formation clays reduces permeability of reservoir rock and that the permeability decreases as salinity of the water decreases. Data in these references, however, concern the permeability change with only a single fluid present. A more pertinent and direct consideration in the production of oil and gas from wells is the permeability change when two fluids, oil and water, are present. Recognizing this, Nowak and Kreuger2 and Bertness1" considered several ways in which mud filtrates and saline solutions caused reductions in the oil permeability of formation cores. Investigations discussed here were designed to supplement information in the literature on changes in oil

INTRODUCTION This chapter summarizes porphyry copper deposits within the State of Alaska. Prospecting for porphyry copper-type deposits in Alaska germinated during the 1940's, grew slowly during the '50's, boomed during the '60's, and matured in the '70's. Although large expenditures have been made in the search for porphyry-type deposits, most accrued data lies dormant in company files. However, an adequate base exists in the literature for a general synthesis of areas that contain porphyry prospects. To simplify the summary, porphyry molybdenum deposits as defined by Clark (1972) are omitted. Description of deposits in their geologic setting permits some correlations between deposit characteristics and crustal environment. These correlations allow speculation about the genesis of the deposits. The summary also attempts to group deposits on the basis of general mineralogic characteristics because diorite model deposits are separated from quartz phenocryst-bearing hosts. Data presented in this chapter summarize observations by the author, published descriptions of specific areas and deposits as noted in the bibliography, and comments by various government geologists. E. M. MacKevett, Jr., D. H. Richter, and H. C. Berg of the US Geological Survey have been particularly helpful. Because few comprehensive descriptions of individual porphyry copper deposits exist for this area, much of the data presented is new to the literature. Details of structure, isotopic geochemistry, and petro- genesis for individual deposits are largely lacking and even the general geology of some belts is not well understood. Details on petrography of Alaskan porphyry copper occurrences are inadequate for construction of ternary diagrams (e.g., Figs. 36a, b, pp. 103, 104, for the northern Cordilleran orogen). Petrographic descriptions summarized in the text are largely from published descriptions whose sources are cited. Porphyry copper-type deposits in Alaska include deposits with pervasive pyrite that contain disseminated copper (but not necessarily coproduct molybdenum). Available data preclude differentiating the deposits by size. No Alaskan porphyry copper deposit is now in production but this is believed to be, in part, a function of economics. In some cases available geologic information is in- adequate for classifying deposits. Some de- posits included with porphyry copper may, with further exploration, be demonstrated to be some other genetic type. Alaska has three distinct porphyry copper provinces: the Hogatza plutonic belt, the Continental Margin belt, and the Interior belt. Each belt contains deposits with characteristic geologic features distinct from those of other belts. Fig. 24 shows the continental margin belt to extend inland from

Jan 1, 1978

HE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given composition and quality. In comparison with other steelmaking methods, the basic open-hearth process is one of the most versa- tile, both from the standpoint of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. With some types of liquid-metal charges, the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO). This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SiO2) , manganese oxide (MnO), iron oxides (FeO and Fe2O3), and phosphorus oxide (P2O5) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course

Jan 1, 1951

Jan 1, 1970

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for spectroscopically pure silver, and for o series of solid solutions of silver with cadmium, indium, and tin, using a Ke-type torsion pendulum apparatus. Some experiments have also been made to investigate the effect of nonmetallic impurity on grain boundary relaxation in silver. The effect of the alloying elements is to increase the grain boundary viscosity, and to raise the activation energy for grain boundary relaxation from 22,000 cal per mol for pure silver to 43,000 cal per mol for the solid solutions; the same value being obtained, within the limits of experimental error, for all the alloying elements and solute concentrations investigated. Results of the experiments show exactly the same trend as those obtained previously for a similar series of copper solid solutions. They are in agreement with the general theory of grain boundary relaxation developed by Zener and Ke, but do not seem to be in agreement with either of the mechanisms so far put forward to explain grain boundary slip. EXPERIMENTS described in this paper were made as part of an investigation into the effect of alloying elements in substitutional solid solution on grain boundary viscosity, measured by the internal friction method developed by Ke.&apos; The apparatus and experimental procedure have already been described.&apos; Preliminary work was done with spectro-scopically pure silver. Experimental Work Materials Used—All the materials were supplied in the form of % mm diam wire by Messrs. Johnson Matthey and Co. Ltd. The silver and all the alloying elements used were spectroscopically pure. Composition of the alloys is given in Table I. They were all melted and chill cast under the same conditions as the copper alloys. The ingots were rolled to 1/4 in. sq rod with intermediate annealing at 600°C in an atmosphere of cracked ammonia when necessary. These rods were then drawn to wire by standard procedure with intermediate bright anneals at suitable steps in the drawing operations. Specimens from the annealed wires were sectioned longitudinally. mechanically polished, and examined under the microscope. They were then etched and reexamined. Grain sizes were reasonably uniform for all wires, and no traces of a second constituent were observed. The wires were weighed before and after testing so as to measure any loss of the alloying element due to evaporation. The loss was less than the accuracy of measurement—< 0.1 pct of the total weight— for the Ag-In and Ag-Sn alloys, but appreciable loss of weight occurred in the case of the Ag-Cd alloys. The percentage loss is given in Table 11. X-ray diffraction photographs were taken of all thc wires after test to determine whether there was any marked preferred orientation. Results of the examination are given in Table 111. Experiments on Spectroscopically Pure Silver-— Experiments were made on specimens in which the grain diameter was small relative to that of the wire, and on one specimen in which the grains were grown by the usual strain-anneal method to extend across the full diameter of the wire. These large grained specimens will be referred to as single crystal specimens. The wires were annealed for 11/2 hr at 700°C, and experiments were made at two frequencies of vibration, 1.5 and 0.4 vibrations per sec. The variation of internal friction with temperature is shown in Fig. 1. Experiments on a second small grain specimen gave approximately the same results as for the first wire. It will be seen from Fig. 1 that the peak in the curve for the small grained wire, which is presum-

Jan 1, 1957

By Turno De Michelis

The Porto Marghera plant was erected in 1936 for the production of 10,000 tons of electrolytic zinc annually. Since then it has been continuously enlarged until annual production of the metal reached 40,000 tons in 1969. At the same time the processing cycle was modified bringing it up to date with modern techniques, and was completed by installations for the recovery of by-products in the minerals treated and subsequent processing of the base metal. 90% of the zinc produced is of 99.993% purity . At present the plant comprises, first of all, the zinc blende desulphuration department which has a single modern fluid bed furnace capable of processing 220 - 250 tons of dry crude mineral daily; it is connected to the sulphuric acid plant with its three catalysis sections each capable of producing 60-70 tons of sul9huri.c acid monohydrate daily. The roasted blende is conveyed pneumatically to plants for leaching of the zinc and purification of the resulting solution. During recent years this department has been completely transformed from the discontinuous cycle, for which it was built, to the continuous cycle, paying great attention to

Jan 1, 1970

Jan 12, 1951

By R. D. Mollison, C. F. Fogarty

Sulfur is widely distributed in nature. It is present in the earth&apos;s crust, the ocean, the meteorites that come to us from cosmic space and in practically all animal and plant life. According to Clarke,9 the earth&apos;s crust contains 0.06 pct sulfur. Large quantities of free or combined sulfur are found in coal, natural gas and petroleum. Mineral waters contain sulfates and hydrogen sulfide. Sulfur is rather plentiful in the crust of the earth; however, only under special circumstances can it be produced profitably. Sulfur is one of the cheapest raw materials used by industry; and, therefore, the economic feasibility of a given deposit is strongly dictated by the law of supply and demand on local as well as world-wide levels. The forms which are commercially important are elemental sulfur or brimstone, and the sulfides such as pyrite (FeS2), pyrrhotite (FenSn+1), chalcocite (Cu2S), sphalerite (ZnS), and galena (PbS); the sulfates such as gypsum (CaSO4,2H2O), anhydrite (CaSO4), and kieserite (MgSO4,H2O). Elemental Sulfur Elemental sulfur is found in many localities, generally in solfataras and gypsum type deposits. The solfatara deposits are found commonly in the neighborhood of active or extinct volcanoes as in Italy, Japan and Chile, or fumaroles associated with mineral springs such as the Mammoth Hot Springs in Yellowstone Park. Here the sulfur is deposited in tufas or other porous host rocks. This type of sulfur deposit probably results from the oxidation of hydrogen sulfide or the reaction of hydrogen sulfide with sulfur dioxide. Most of the world&apos;s supply of elemental sulfur comes from the gypsum-type deposits. Here the mineral occurs as either crystalline or amorphous sulfur in sedimentary rocks in close association with gypsum and limestone. This association is characteristic and occurs in almost all the great gypsum beds of the world, although sulfur is not always present in quantities of economic importance. Various theories have been advanced to account for this association. Bischof5 suggested that the sulfur came from hydrogen sulfide which resulted from the reduction of calcium sulfate by carbon or methane in accordance with the following reactions: CaSO4 + 2C= CaS + 2CO2 CaS + C02+ H2O = CaCO3 + H2S CaSO4 + CH4= CaS + C02+ 2H20 2H2S + 02= 2H20 + 2S All of the sulfur-bearing domes on the Gulf Coast have calcium sulfate in great quantity in the cap. They all show the presence of hydrocarbons. The oxygen for the final reaction could have been supplied by circulating ground waters. The principal objection to this theory is that temperatures of 700° to 1000°C are needed to reduce the sulfate to sulfide with carbon compounds. The geologic evidence is that the temperature of the sulfur-bearing domes of Texas did not exceed 100°C. Proponents of the theory say that geologic time or a catalyst replaced temperature. According to another theory the sulfur in the salt domes is the result of bacterial action. Sulfate reducing bacteria have been detected in sulfur cores and in the formation water issuing from salt domes. It has, therefore, been suggested that these bacteria converted the sulfate to sulfide which subsequently was converted to elemental sulfur.

Jan 1, 1960

By D. T. Farnham

The shale used at the Renton plant of the Denny-Renton Clay and Coal Co. for the manufacture of vitrified paving brick occurs in a hill rising from 200 to 300 ft. above the level of the valley in which the plant is situated.

Jan 1, 1915

Jan 1, 1962

By Linn Bradley, W. W. Strong, H. D. Egbert

A hot-dry method of cleaning the gas from blast furnaces has been shown1 to conserve the sensible heat energy of the gas, and in general it thus permits of a higher flame temperature. The electrical method of cleaning gases removes from 98 to 99 per cent. of the suspended matter in one operation when operating properly, thus making possible the use of a very clean gas for burning in the stoves. The use of such clean gas thus makes feasible a different type of hot-blast stove construction from that being used at present. It therefore seems advisable to construct the stoves from the viewpoint of getting the maximum amount of heat energy into the products of combustion. By preheating the air added to the top gas and obtaining a better mixture of the air and top gas, less excess air will be required and a higher flame temperature obtained from the combustion of the top gas. The interior of the stove should be provided with a kind of brick that will withstand a high flame temperature, will conduct the heat energy along certain directions, insulate the flow of heat along other directions and at the same time store heat energy so as to make the flow of such energy more uniform. It is quite likely that these results can be best obtained by using several kinds of bricks: one type which is a good insulator of heat energy to be used for lining the stove and for making partitions through the stove to restrain the flow of heat; another type of brick or material with high refractory qualities; and a third type which will be a good conductor of heat energy. The surface of the stove exposed to the atmosphere should be a minimum in comparison to the mass of checkerwork which it is possible to obtain, due regard being paid to other conditions. With clean and hot furnace top gas it will be advisable to consider a rearrangement of the checker work in the stoves. One season for the present size and shape of checker openings is to provide facility for

Jan 1, 1917

Jan 1, 1910

Jan 1, 1887

By C. A. Meissner

The; following is a further discussion of the paper of James Qayley, " The Application of Dry-Air Blast to the Manufacture of Iron " (Trans., xxxv., 746), with special reference to his supplementary paper (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 797 to 819), and to the paper of J. E. Johnson, Jr., " Notes on the Physical Action of the Blast Furnace " (Bi-Monthly Bulletin, No. 5, September, 1905, pp. 1111 to 1146). Mr. Gayley&apos;s paper has been discussed also by E. Windsor Richards, R. w. Raymond, E. H. Saniter, W. J. Poster, H. M. Howe, V, Pendred, B. H. Thwaite, James Gayley and Alexander Pourcel (Trans., xxxv., pp. 1022 to 1042), Joseph W. Richards (Bi-Monthly Bulletin, No. 4, July, 1905, pp. &apos;703 to 718); T. W. Robinson (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 788 to 796); C. B. Dudley, R. W. Raymond, J. E. Johnson, Jr., W. F. Mattes, James Gayley, David Baker, John Birkin-bine and F. E. Bachman (Bi-Monthly Bulletin, No. 5, Septem-

Jan 1, 1907

Jan 7, 1950

By Dr. O’Neil Thomas J., Donald W. Gentry

"We can easily represent things as we wish them to be..” -Aesop INTRODUCTION The first eight chapters of this book have primarily addressed the concepts and fundamentals associated with project valuation, particularly as they apply to mining-related projects. Specific emphasis was placed on the engineering and economic parameters and estimates necessary for quantifying line items in pro forma income statements and the subsequent calculation of net annual cash flows. Given these estimates of relative benefits, costs, and annual cash flows for a project, it then becomes necessary to convert these estimates into measures of relative desirability or attractiveness. The criteria and techniques typically utilized to determine project acceptability or desirability are, then, the topics of discussion in this chapter. Before proceeding it may be advantageous to put the problem of project evaluation into proper perspective by reiterating some of the fundamental concepts developed in Chapter 1. The basic premise set forth in this book is that the objective of the firm should be to maximize its value to its owners (stockholders&apos; wealth). This value or wealth is represented by the market price of the firm&apos;s common stock; consequently, the primary objective of the firm can be restated as one of maximizing the value (price) of the firm&apos;s common stock in the marketplace over the long term. This price, in effect, is an indicator or index of the market&apos;s perception of the company&apos;s progress and a reflection of the investment, financing, and dividend decisions made by corporate management. These three major decisions are inter- related and jointly impact the market price of the firm&apos;s stock. Therefore, if the objective of maximizing the value of the firm to its stockholders is to be achieved, an optimal combination of the three decisions will be necessary. It is important to emphasize that maximizing stockholder wealth is not the same as profit maximization or even the maximization of earnings per share. Corporate managers making decisions based on the objectives of maximizing profits and/or earnings per share must recognize that these objectives do not consider: (I) the timing or duration of expected returns, (2) the business and financial risks of the promised earnings, or (3) the dividend policy of the firm. Obviously all of these factors are of concern to the company&apos;s stockholders and will have an effect on the market value or price of the firm&apos;s common stock. Maximizing market price per share, or wealth maximization, is therefore the appropriate corporate objective and

Jan 1, 1984

By E. H. Sellards

PHOSPHATE rock like most other mineral substances is found in nature in varying degrees of purity. Of the impurities that are present some are constituents of the rock itself; others are inclusions of a foreign substance within the rock; while still others represent merely associated materials or minerals, either clinging to the rock or found in cavities and natural depressions, and hence largely removed in mining. Some of these impurities are distinctly deleterious to the processes of manufacture for which the phosphate is mined, while others, although neutral in action or nearly so, yet by their presence reduce the average grade of the rock and thus acid useless bulk to the shipment. It is the object of refined processes of mining to bring the product, as delivered from the mine, to the highest possible grade consistent with the market requirements and demands. This, however, is not accom-plished without actual loss in the form of discarded phosphate. It is evident, therefore, that the devising of methods for reducing this loss in mining, and yet maintaining the grade of the rock which the market requires, is one of the serious problems that the producers have to face.

Jan 9, 1914

By C. L. Ray, R. E. Baarson, H. B. Treweek

As an example of nonmetallic mineral flotation, the separation of several pegmatite minerals will be discussed in considerable detail, from both the laboratory-testing and plant-operation standpoints. The pegmatites have been chosen to illustrate the practicality of the selective separations of the minerals in a complex nonmetallic ore and, in so doing, to set forth a summation of the flotation art and technology which is applicable in part to the beneficiation of several less complex nonmetallic ores. In addition, a brief summary of descriptions of other nonnietallic mineral flowsheets and separations is included. Some of the industrial minerals now being concentrated by froth flotation methods commercially, or in the laboratory, are listed in Table 1. GENERAL CONSIDERATIONS There are two classes of chemicals that are normally utilized as collectors in froth flotation separations of nonmetallic minerals. These are defined as anionic and cationic and are typified by the fatty acids and amines, respectively. The fatty acids are selective to those minerals that have a high concentration of positive surface charges, such as the various calcium minerals typified by calcite, phosphate rock, and fluorspar. The amines are selective to those minerals with a high concentration of negative surface charges, such as silica sand and silicates. It should be noted, however, that by using various inorganic chemicals, a new or synthetic surface can be placed on specific minerals which produces different characteristics, thereby reversing the flotation reagent required for separation. The polar end of the collector attaches to the mineral surface either by chemical or physical adsorption; the nonpolar unreactive end is oriented away from the mineral surface. The result is a hydrophobic coating at the mineral surface which causes attachment to air bubbles. It is this surface condition that permits the floating of minerals which normally sink in water. In order to utilize these fatty acids and amine derivatives, several conditions .must be fulfilled. Before there can be a selective flotation process,

Jan 1, 1962

By M. R. Geer, H. F. Yancey

WITH the exception of pneumatic processes and ii few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral- dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficiation process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and else- where, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment for many years, and more recently driers employing centrifugal force have gained in popularity. 1 A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal-a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. OBJECT AND SCOPE OF INVESTIGATION Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it on coal slurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1948

By P. Datta, L. L. Handy

For a wetting phase displacing a nonwetting phase from a porous medium the distribution of the residual fluid may depend on displacement conditions. Although this subject has been debated in the literature, only a few experiments have been cited to support the various conclusions. Experimental results presented in this paper show that fluid distributions are dependent on imbibition pmcedures. Results agree qualitatively with predictions from the pore doublet model. If the rate of water imbibition is restricted, the nonwetting phase is trapped preferentially in .the larger pores as expected. But if the rate of water imbibition is unrestricted, trapping occurs somewhat more in the smaller pores. These conclusions were deduced primarily from relative permeability measurements. INTRODUCTION Relative permeabilities are known to depend on the saturation history of the porous medium. For either continuously increasing or continuously decreasing wetting phase saturations, however, they have normally been assumed to be single-valued functions of saturation. Severat investigators have compared relative permeabilities measured by different methods and have reported acceptable agreement.1-5 Studies of simple models of the displacement process suggest that the distribution of residual fluids can be influenced by the displacement method. If this is so, relative permeabilities also should depend on the method of displacement. These predictions have not been supported by experimental data. The object of this paper is to investigate experimentally some of the predictions of these model studies. The particular question of importance is whether steady-state and unsteady-state methods should be expected to give the same values of relative permeability. Much of the reported data showing agreement between steady-state and unsteady-state methods have been obtained on un consolidated sand. Johnson, Bossler and Naumann, however, compared steady-state and unsteady-state results for Weiler sandstone and found no significant differences.5 Levine made a detailed study of pressure and saturation distributions for a laboratory waterflood in a consolidated system but made no attempt to calculate performance from steady-state relative permeability data Bail and Marsden in a somewhat similar set of experiments did attempt a comparison of observations with predictions but the results were inconclusive.7 Excluding gravity, two forces affect the distribution of wetting and nonwetting phases during an unsteady-state, immiscible displacement: viscous and capillary forces. If relative permeabilities are indeed the same when measured by steady- or unsteady-state methods, the fluid distributions at the same fluid saturations must be similar for both methods. Furthermore, the implication is that the relation between capillary and viscous forces is the same for both methods insofar as the effect on microscopic fluid distributions is concerned. Unsteady-state displacements are normally run at high rates to maximize the ratio of the viscous to capillary forces. The objective is to reduce the effect of capillary forces on macroscopic fluid distributions. For floods in which the phase which wets the porous medium displaces the nonwetting phase, capillary forces compete with viscous forces in determining fluid distributions.8 The residual nonwetting phase is discontinuous. Competitive aspects of viscous and capillary forces and the resulting effect on water-oil distribution in porous media have been illustrated in an elementary way using a pore doublet model. This model and predictions from it have been discussed at considerable length by Rose and Witherspoon, Rose and Cleary and by Moore and Slobod.9-13 Rose and Witherspoon show that so long as water invades the model at a rate equal to or greater than the free imbibition rate, the water will move through the larger capillary of a doublet first and trap oil in the smaller capillary. On the other hand, if a negative pressure is applied to the water

Jan 1, 1967