Search Documents

By S. E. Maddigan, B. R. Zimmerman

Most metallurgists are well acquainted with the contributions already made to the study of metals by the use of X-rays. On the one hand, the radiographic method is constantly becoming of increasing importance as a nondestructive testing procedure, while on the other hand the techniques of X-ray diffraction have made important contributions to the fundamental knowledge in studies of phase diagrams, stress conditions, and so forth. A new, and as yet insufficiently appreciated, tool exists in the application of microradiography to alloy structures. This new procedure in many respects bears the same relation to microscopic investigations as does macroradiography to the gross inspection of metal surfaces. However, where macroradiography is used ordinarily to determine the soundness of the metal structure, this new method can be used not only to investigate micro-un-soundness but also to examine the distribution of the constituent elements within the body of the alloy. When combined with the normal procedures of microscopy, this offers a technique of great potential power. It is intended in this paper to present a few examples of copper-base alloys demonstrating the additional knowledge obtained from the microradiographic method. The detection of micro-unsoundness is demonstrated in Fig. I for a sample of cartridge brass as cast. The sample ap- peared quite sound when viewed under the microscope, but in reality was thickly populated with minute voids. This application of the method conforms in every way to conventional large-scale radiography and has been used to facilitate production of metal for vacuum devices.' The true potentialities of the technique are revealed by comparison of Figs, 2a and 2b, which are respectively a photomicrograph and a microradiograph of a cast alloy of 80 per cent Cu, 10 per cent Sn, 10 per cent Pb. The remarkable difference in appearance provides some concept of the additional information this method may yield when used as an auxiliary to microscopic studies. Fig. 2a shows two phases of the copper-tin system plus segregated_ lumps of lead. Fig. 2b, on the other hand, shows with exceptional clarity the actual dendritic growth of the metal crystals during solidification. The practice of microradiography depends upon the laws of absorption of X-rays. This subject has been reviewed thoroughly in recent papers,l,2,3 but for clarity a brief resume will be given here. As is well known, when a beam of X-rays is transmitted through a, layer of homogeneous material, the intensity is reduced according to the relation: where Il is the transmitted intensity, I0 is the incident intensity, µ1 is the linear absorption coefficient of the material, t1 is the thickness of the material.

Jan 1, 1944

By S. B. Christy

The practice of the cyanide-process of gold-extraction has brought to light many important contradictions of familiar chemical analogies, which still obscure both the theory and the practice of the art with distinctions subtler and more difficult to make or follow than those which delighted the heart of the old-time metaphysician. Yet Nature herself has drawn these distinctions; and if we hope to succeed in this modern search for the Golden Fleece, we must be able to follow her through the winding labyrinth. There are so many phases of this question that I shall attempt to touch on only one of them at this time, but it is one that lies at the root of many others. In reviewing my paper on " The Solution and Precipitation of Cyanide of Gold,"* Mr. E. B. Wilson contends† that" in the solution of gold by means of alkaline cyanides the various reactions are determined, as to their order and intensity, by the relative position of the elements concerned in the electro-chemical series, or series of voltaic tension." In a modified form this statement is probably true. That is to say, the difference of electrical potential in any closed electrical circuit determines the nature of the reactions which ensue. But the matter is not so simple as Mr. Wilson assumes. Recent investigations show that the order of the metals in the electro-chemical series depends not only on the nature of the elements themselves, but also on the chemical composition of the solution in which they are placed; its degree of concentration; its temperature; and, in the case of gases, on the pressure. Unless all these conditions are taken into account, inferences drawn from the electro-chemical series are likely to prove more

Jan 1, 1901

By R. S. Dean

BLUE HEAT PHENOMENA IN constructing a theory of the flow and hardening of metals, we necessarily make use of such phenomena as seem to be, universally observed in metals. It is, therefore, a matter of. concern to the constructors of such mnemonic systems if one or two of the group classified as metals show anomalous behavior. Such egregious phenomena are observed in pure or nearly-pure iron in the reaction of its mechanical properties to low-temperature annealing after cold work and to increased temperature of testing. In short it has been generally observed that iron," as an outstanding exception among metals, increases its hardness and strength by low-temperature annealing. after cold work,1 and also by increase of testing temperature to the range of 150° to 300° C. The investigation here recorded was made then with the object of ascertaining if similar phenomena were observed in high purity iron and, if not, to the presence of which impurities these phenomena could be traced.

Jan 1, 1929

By R. W. Raymond

This name is applied to the present mining law, as enacted in 1872 and since, to indicate its leading characteristic—in which it differs from all previous mining laws of this or any other country. The earlier act, passed in 1866, was practically the first attempt of Congress to deal with the question of mining titles upon the public domain. It was framed after nearly twenty years of acquiescence on the part of the Government in the self-constituted tribunals, officials, rules, and customs of the mining districts. In its recognition of these, and in several other particulars, the act of 1866 was open to serious criticisms. It is the purpose of this paper, not to trace the history of legislation on this subject, or show in detail what were the faults of the earlier law, but rather, by a discussion of certain aspects of the present law, to point out how great a revoluition it has effected in the rights of mining locators, and to indicate some of the difficulties attending its application. In the attempt to correct the vagueness of the act of 1866 an entirely new elernent was introduced into the law, bringing with it a new set of difficulties. Under the act of 1866 and the miners' customs which it followed, the lode was the thing claimed and subsequently acquired by patent. And the claim to a given number of feet on the longitudinal course of the lode was rooted in 'a discovery of any part of the lode in any part of the claim. ("Extensions" could in many districts—perhaps universally—be located and claimed on the strength of the discovery in the principal claim to which they referred; but this is a point not essential to the present discussion.) It was not necessary to find the outcrop or the upper edge of a lode in order to lay a valid location upon it. An explorer, sinking a shaft and intersecting a lode not already discovered and claimed by another, could claim by that discovery the number of feet along that lode which the local laws might permit (not exceeding the maximum set by the United States statute) whether his sur-

Jan 1, 1884

By Alfred E. Hunt

Tars paper is suggested by the appointment on the part of the American Societies of Mechanical and of Civil Engineers of committees upon the subjects of " Standard Tests and Methods of Testing," and " Uniform Methods of Tests of Material used in Metallic Structures," respectively, and by a study of the report of one of these committees, and other papers. Moreover, the writer has had frequent occasion to hear the complahts of tnanufacturers who furnish structural material subject to specifications, that in the tests prescribed, the number of tests required, and the methods of making

Jan 1, 1892

By C. O. Worden, E. K. Landgraf, C. A. Zapffe

Following the discovery of Parke and Ham that deoxidation control of cast molybdenum can be predicated upon simple fractographic examination, a special study of that metal was undertaken to investigate those patterns ascribed to forge-ability and nonforgeability. An elaborately developed system of cleavage patterns immediately rewarded the study; and they are reported here as a necessarily preliminary contribution calling attention to information which is both new in type and in origin. In general, the present observations confirm those of Parke and Ham, and Wood-side; but they also disclose a wealth of detail and correlated phenomena which greatly expand the earlier information. For example, the oxide pattern of nonforgeability is found to be complex, perhaps involving as many as three distinctive patterns, And the nature of the carbide seems to be at least twofold. In addition, transgranular facets are here shown for the first time. Elaborately complex, but in a characteristic manner, these facets depict distortion in original crystal growth which provides truly extraordinary patterns. No carbide and oxide forms display themselves transgranularly, except in profile as exceedingly thin superficial films at the grain boundaries. Crys-tallographic features are also rare—a condition undoubtedly resulting from the great substructural distortion; but occasionally registrations are found of cleavage on {00I}, and faulted areas believed to be Neumann-type deformation on I I121. Introduction Parbe and Ham,' and again Woodside,2 have reported that the forgeability of molybdenum cast by their Vacuum-electric-arc Process can be predicted with great dependability by a simple fractographic observation. They state that nonforgeability is the result of a grain boundary oxide which can be readily identified on the fracture facet at high magnification; and they convert the nonforgeable condition to a forgeable one by increasing the carbon content of the melt until the oxide structures subsequently observed in the fracto-graph become replaced by a second strongly marked pattern characteristic of carbide and coincidentally indicative of forgeability. Considerable importance immediately attaches to such observations: (I) because of their direct commercial application to one of metallurgy's inviting and relatively unexplored metals; (2) because of a general scientific curiosity regarding the nature of these characteristic markings; and (3) perhaps more important, because of

Jan 1, 1949

By E. T. Turkdogan

This paper deals with an analysis of the conditions leading to the formation of blowholes and surface and subsurface defects in cast low-carbon steels. The theoretical analysis of the problem is based on the concept of the occurrence of deoxidation reactions during cooling of liquid steel and during its solidification. The reaction equilibrium data are given on deoxidation of steel by carbon, silicon, and manganese. The details of the calculations are given on the simultaneous deoxidation of steel by silico-manganese additions to produce a desired level of deoxidation at certain residual concentrations. Based on an idealized model, an attempt is made to calculate the enrichment of solutes in the solidifying liquid entrapped within the interdendritic cells which are known to be less than 200 µ thick. Formulae are derived for the calculation of the change in the residual oxygen content of the enriched liquid steel, controlled by Si/Mn deoxidation. It is shown that for every particular initial silicon, manganese, and oxygen concentration in steel (as residuals in liquid solution at the beginning of solidification) there is a particular carbon concentration below which carbon monoxide, leading to blowholes or pinholes, is not expected to form. There are a number of independent variables which have a decisive influence on the formation of blowholes. For example, it is shown that the position of the curve depicting the critical relation between initial silicon and carbon content for suppression of the evolution of carbon monoxide) can be shifted to lower silicon or higher carbon levels by: increasing manganese content; decreasing oxygen, hydrogen, or nitrogen content; or increasing external pressure on the solidifying mass. FOR the production of sound castings it is essential to prevent the formation of interdendritic worm-holes or pinholes brought about by gas evolution during solidification. Another major problem encountered in solidification of ingots is the formation of surface defects. These problems are thought to be closely associated with the deoxidation reaction occurring in liquid steel during cooling and subsequent solidification. As the liquid becomes richer in impurities during dendritic solidification of steel, a series of reactions may occur in the liquid phase trapped within the branches of growing dendrite platelets. Because of the strong interaction between dissolved oxygen and impurities in liquid steel, the reactions most likely to occur are of the deoxidation type. However, inherent to the extreme complexity of the problem in question, numerous simplifying assump-

Jan 1, 1965

Inflation, fuel shortages, environmental restrictions, and a worldwide recession that sharply curtailed the demand for goods and services, were the main causes for the poor performance & virtually all industrial minerals in 1975. This poor showing was not a surprise. As Felix Shay correctly predicted in his introductory remarks to last year's industrial Minerals Review (ME, Feb. 1975, p. 70), ". . . the minerals industry will soon be facing falling demand as a consequence of sharp declines in auto production, housing, appliances, and other consumer goods. Moreover, when sales weaken. the high-volume, low-priced industrial minerals will incur sharply.

Jan 3, 1976

By Henry Howe

1. Introduction.-This paper is based in large part on the examination of two rings, shown in section in Fig. 4 to 15, cut from an eroded 14-in. (35.56-cm.) gun, liner, and containing, according to Booth, Garrett, & Blair: Carbon, 0.380 per cent.; manganese, 0.655 per cent.; nickel, 2.810 per cent.; vanadium, 0; chromium, a few hundredths of 1 per cent.; tungsten, 0; molybdenum, 0. These rings were received from Admiral Joseph Strauss, then Chief of Ordnance, U. S. Navy, through the kindness of Mr. Hudson Maxim, Chairman of the Committee on Ordnance and Explosives,, of the U. S. Naval Consulting Board.

Jan 2, 1918

By Richard L. Gordon

Minerals long have been important commodities in international trade. As an inevitable result, the governments of the world have employed a wide variety of programs that affect the flow of trade. Roughly speaking, we may distinguish between the desire of more developed countries (MDCs) like the United States, western Europe, and Japan to control imports of minerals and the concern of less developed countries (LDCs), like India, about exploiting and exporting their minerals. The terminology used to describe different countries and the classification of specific countries into groups is unsettled and often changing. The poorest countries have been characterized as backward, undeveloped, underdeveloped, and developing. The problem seems to be in selecting a term that is both accurate and polite. Less developed seems, for reasons outlined by Hagen [pp. 51-57], the most convenient term. The borderline between an LDC and an MDC is always open to dispute. Objective measures are difficult to develop because of deficiencies in basic data, and enormous conceptual problems arise in making valid comparisons from even good data [see Hagen, pp. 7-28]. Thus, policies of the MDCs can be evaluated chiefly by using a few basic arguments for protectionist attitudes towards international trade. In dealing with the LDCs, a more far-ranging evaluation that covers general economic policy goals, the role of foreign investment, and the indirect effects of trade is required. This duality breaks down when trying to deal with the depressed areas in an MDC; here the issues are more akin to those associated with problems in an LDC. Similarly, variants of arguments used in LDCs appear in debates about foreign investments in MDCs. The whole discussion of minerals in LDCs, moreover, has obvious implications for MDCs like Canada and Australia. They, too, must face problems about the best utilization of their resources. THE RESTRICTION OF MINERAL TRADE BY DEVELOPED COUNTRIES[a] At least to some extent, the world's leading industrial nations have intervened to control the inflow of minerals. Such regulation is particularly pronounced for energy. Both the United States and western Europe employ

Jan 1, 1976

Jan 1, 1953

Jan 1, 1953

By Douglas R. Piteau, Dennis C. Martin

Instability of rock slopes may occur by failure along pre- existing structural discontinuities, by failure through intact material or by failure along a surface formed partly along discontinuities and partly through intact material. Although certain fundamental failure modes are recognized, the mechanisms of slope failure are varied and complex. Such mechanisms are governed by the engineering geology conditions of the rock mass, which are almost always unique to a particular site. An understanding of failure mechanisms requires a knowledge of the physical, mechanical and strength properties of the intact material and discontinuities which make up the rock mass, as well as the structural geology and hydrogeology. These engineering geology parameters also must be evaluated with respect to the slope geometry to determine failures which are kinematically possible. Only after obtaining a reasonable appreciation of the possible failure modes can a rational mechanical stability analysis be carried out. Both two-dimensional and three-dimensional failure mechanisms should be considered in assessing the design of rock slopes. Simple analyses methods are used initially to identify those possible failures which could control slope stability. More complex and detailed analyses usually are required for a few critical failure modes which could control stability, or where a more complex type of failure mechanism is envisaged. Complex failure mechanisms are usually identified when assessing previous slope failures. More detailed information concerning slope geometry and engineering geology parameters must be acquired where analyses must be more rigorous.

Jan 1, 1983

By D. M. Milne, R. F. Stoner, W. Bakiewicz

The Lower Indus Basin deposits form a substantial unconfined alluvial aquifer of excellent quality. This aquifer contains basically highly saline groundwater, overlain in places by considerable amounts of fresh water whose origin can be traced to the present and historical courses of the River Indus. In the past, the main source of groundwater recharge has been direct river seepage and water tables were generally deep. Since the establishment of a perennial irrigation regime however, deep percolation from the increased irrigation supplies has predominated and the water table has risen to within a few feet of the surface. The river system itself is being progressively devel-oped for irrigation and very shortly a situation will arise where the entire low winter flow will be utilized. Fresh groundwater will then be exploited to supplement the surface supplies, and at the same time a drainage system, mainly based on wells will be used to stabilize the water table at safe depths. This paper discusses some of the methods used to ensure optimum economic development of the fresh groundwater and describes the general design philosophy evolved by the authors' firms for both irrigation and drainage wells, with respect to both well configuration and operation. Water quality standards are discussed insofar as they affect subsequent use of the groundwater. A few particular aspects are considered, including the values of the relevant aquifer constants, the construction of wells, and the determination of screen losses. A major problem solved during the Lower Indus Project investigations has been the design of wells to produce fresh water from layers overlying saline water. This solution is also discussed. The recent interest in the groundwater of the Lower Indus Plains of West Pakistan has two main aspects. Firstly, soil waterlogging and the associated salinity hazards caused by rising water tables are a serious problem in agriculture, and the ease with which drainage requirements can be met by aquifer pumping makes this an obvious solution. The second interest stems from the rapid intensification of irrigation agriculture and the growing shortage of water supplies. In the areas where the groundwater is of suitable quality it can be used immediately for irrigation at relatively small cost and with large financial returns. In addition, the aquifer forms a potential storage reservoir which could be recharged from high river flows and depleted by pumping at times of scarcity. SOURCE OF GROUNDWATER The Lower Indus plain is a relatively long and narrow alluvial basin on a north-south axis, some 23,000 sq miles in area, bounded by higher land to the east and west. One hypothesis to explain the distribution and quality of groundwater in the region1 presupposes a river system considerably larger than, but very similar to the present river. This is characterized by a single mainstream, with subsidiary overspill channels in times of flood, running along the crest of a self-deposited ridge and with an extensive advancing delta. Sea water is contained in the alluvial pores of the advancing delta, forming the native groundwater. This has been partially displaced from two sources, namely direct seepage of fresh water from the river channel in meander flood plain areas and percolation from flood spillage in cover flood plain areas. Percolation has been subject to much re-evaporation and is thus slightly saline even as it reaches the groundwater. The whole complex has been further affected by two main influences: evapotranspiration from the land surface that tends to salinize the groundwater and down-valley flow that tends to bring fresher water

Jan 1, 1970

By G. S. Cole, G. F. Bolling

Fluid flow strongly influences ingl structure and the columnar -to-equaaxed transition. Artificial flow patterns siwzilar to the nuturul ones act to induce this transition, while dampening forces act to suppress this transition. It is shown here how simple mechanical forces can be applied to a systerrz in order to induce or slipPvess relative fluid flow and the change both the structure transition and the exact structures obtained. The example used is the effect of slow rotations and oscillations 012 a cooling- ingot (of laboratory scale). The details of rotution and oscillation for various cooling rates, lenlperal~ire gradients, and sizes of ingot are related to other solidzfication variables. THE grain structure of a casting can be changed by altering the fluid motion during solidification. Just how important these changes are depends directly upon the degree to which the fluid motion can be controlled. An early step in understanding the nature and influences of fluid motion was taken by studying natural thermal convection; when a static mechanical device was used to suppress natural flow the result was opposite to that obtained when an electromagnetic device was used to augnlent flow in a pattern similar to the natural one. ''2 Suppression allowed more columnar growth to occur, but "augmented natural convection" brought about an earlier columnar-to-equiaxed transition (CET). Since the solidification of a free ingot must have characteristics somewhere between those displayed during suppression and augmentation, we know that natural convection must influence the CET. Further, since heat transfer in the liquid is always some time-dependent combination of convection and conduction, it can easily be guessed that the temperature gradient in the liquid is the vital factor affecting the CET.1,2 It is obvious that the structure arising from the unadulterated solidification of an ingot, without external influence, is rarely if ever the best possible one. Although the pattern of the natural fluid flow may be considered efficient, the magnitude of the flow and the heat transfer decrease freely from the outset. For a

Jan 1, 1968

By V. E. Elliott, C. L. Meyette

THE conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams -and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a useable and relatively simple solution to a bothersome problem. BASIS FOR CLASSIFYING In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will he used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined' as a zone of

Jan 1, 1948

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or bookkeeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. The emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1959

By Lyman Taylor, Alexander R. Troiano

STUDIES of the transformation of austenite at constant subcritical temperatures have been numerous since the work of Davenport and Bain.1 Considerable information has been obtained on low-alloy steels and on high-carbon alloys containing undissolved carbide or graphite at the austenitizing temperature. Little is known of the isothermal transformation of austenite containing in solution large amounts of both carbon and a single alloying element. In this investigation four steels containing one per cent carbon and with chromium in the range 3 to 9 per cent have been examined with the view to establishing the fundamental character of the isothermal reactions when all carbon and chromium are initially in solution in austenite. EXPERIMENTAL PROCEDURE Alloys The chemical compositions of the steels investigated are given in Table I. The 4 per cent Cr alloy is a commercial steel. The other steels were made by the Carpenter Steel Co. as 50-lb., induction-furnace heats and rolled to 5/8-in. round bars. Bars were softened at 650° to 700°C. before the specimens were cut. [ ] Metallographic Method Most of the lines on the transformation diagrams presented here have been placed on the basis of the microscopic examination of partially reacted specimens. Thees specimens were approximately ½ by ¼ by 1/8 in. in size. Specimens of the 9 per cent Cr steel were held 10 to 12 hr. at 1200° to I225°C. before quenching to the various subcritical temperatures. The other steels were held for 2 to 2 ½ hr. at 1200°C. before quenching. These treatments, carried out in an atmosphere of purified nitrogen, produced an austenite grain size larger than A.S.T.M. No. I, some grains being 1 to 2 mm. in diameter. There were a few undissolved carbide particles in some specimens of the 9 per cent Cr steel. It is believed, however, that any errors in the results due to incomplete solution of carbon and chromium in austenite are negligible; that is, austenite compositions may be considered as being those listed in Table I. X-ray Methods Constituents were identified and martensite axial ratios determined from Debye

Jan 1, 1945

By J. E. Lamar, J. S. Machin

INSULATING materials include a wide variety of nonmetallic mineral products such as exfoliated vermiculite, expanded gypsum, 85 pct magnesia, diatomite, asbestos, perlite, cellular glass, pumice, silica aerogel, expanded aggregates and mineral wool. Except mineral wool, most of these products, or the materials from which they are manufactured, are described in other chapters of this book. PROPERTIES OF INSULATING MATERIALS The insulating properties of the materials considered in this chapter result in general from entrapping extremely small pockets of air in such a manner that heat is not transferred by convection. The minimum heat conductivities of such insulating materials are slightly greater therefore than the conductivity of still air. In addition, conductivity varies with the overall density of the material, the temperature range in which the measurements are made, and the form into which the material is fabricated. However, the numerical value of heat conductivity should not be the sole criterion of an insulating material; for a particular application it may be advantageous to use a material of somewhat higher conductivity in order to secure other desirable engineering properties. This is especially true with certain materials that are used because of their refractoriness. Comparative insulating values of some commonly used insulating materials are shown in Table 1. In comparing the values presented in this table it should be borne in mind that heat conductivity varies with the mean temperature, with the overall density, and with the amount of moisture present. With fibrous or granular materials it varies with fiber or grain size and with the amount and kind of binder, if any is used. Under some circumstances it may vary with the arrangement of

Jan 1, 1949

By Walter C. Lawson

The primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in the Morenci open pit. General Mining Operations Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months' period (Fig I). Broken ore and waste is loaded into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high. They are blasted with churn drill holes and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). Preparation OF Panel Grade In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many tics broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed, to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1949