Search Documents

By K. E. J. Rapperport, C. S. Hartley

The only slip system observed in zirconium crystals deformed at 77", 575", and 1075OK was (1010) [1210] with a critical resolved shear stress in tension of 1.0 kg per sq mm at 77°K; 0.2 kg per sq mm at 575 °K; and 0.02 kg per sq mm at 1075 OK. The active twin planes were {1012}, (1121}, (11221, and (11233) with varying temperature dependence. A detailed analysis for the slip direction using Laue spot asterism is appended. NeARLY all metals of the hexagonal close-packed structure exhibit basal slip, i. e.,(0002)<1120>- type slip. This is true of magnesium,&apos; zinc,&apos; cadmium,3 beryllium,4 titanium,= yttrium,6 and rhenium.Many of these such as titanium 5&apos;8-&apos;0beryllium,4&apos;" magnesium, and zinc13&apos;14 display other slip modes even at room temperature, and nearly all have been reported to slip on other systems under particular loading or temperature conditions of testing. As is shown in this paper, basal slip was not found at any of four test temperatures from 77" to 1075°K in hexagonal close-packed zirconium under the simple loading conditions of tension and compression, even though in one case the resolved shear stress on the inactive (0002) <llgO> system was twenty-five times higher than the critical resolved shear stress on the active (1010) [1210] system. This result is consistent with prior studies on the active deformation processes in zirconium deformed at room temperature. &apos;&apos;-I7 SPECIMEN PREPARATION A) Material—The zirconium used in this work was of two types: 1) as-deposited reactor grade crystal-bar, and 2) arc-melted and forged reactor grade crystal-bar. Typical chemical and spectrographic analyses of these materials as received, and after hydrogen removal and crystal growth are given in Ref. 17. Crystals of type 1) above have the letter prefix (A) and those of type 2) have the prefix (B) throughout this paper. B) Crystal Growth— he zirconium was machined into rectangular parallelepipeds about 0.2-in. scl in cross section and 2 in. iong. These were hand polished through 4/0 abrasive paper, electropolished, given a hydrogen removal anneal, and subjected to long-time anneals at 840 °C in vacuo to produce usable crystals.&apos;7 A second technique used to obtain large crystals was to cycle the samples two or three times between 1200" and 840°C, allowing them to remain at the higher temperature for about 4 hr and at the lower temperature for 5 days.17 These techniques yielded some grains which occupied the entire cross section of the bar and were as long as 3/4 in. C) Orientation Determination—After the growth of large crystals by thermal cycling, the samples were repolished with extreme care through 4/0 abrasive paper and electropolished. Metallographic examination after polishing showed the surfaces to be free of visible deformation traces. Standard Laue back-reflection X-ray techniques were used to find the crystallographic orientations of selected large grains with respect to a specimen face and edge. Fig. 1 shows the stereographic projections of the stress axes for the crystals used. The sharpness of the spots on the Laue photographs indicated that the crystals were of good quality. EXPERIMENTAL METHODS Nine crystals were deformed in tension at 77"K, nine in tension and five in compression at 300°K in previous tests,17 fifteen in tension at 575"K, and eleven in tension at 1075°K. All specimens were stressed by load increments. After a predetermined load was applied, the specimen was removed from the loading appratus and metallographically examined for deformation traces. An attempt was made to initially stress each bar so that some crystals slipped a small amount and others not at all. This was done to bracket the critical resolved shear stress. One bar of special orientation (B-11) was repolished and annealed at 1075°K for 1 hr after lower temperature deformation, before final deformation at 1075°K. In the other bars the loading by increments, followed by metallographic examination, was continued until the surface distortion would interfere with analysis, or until fracture. One example of a crystal pulled to fracture is shown in Fig. 2. This photograph shows a crystal (B-14C) which was pulled at 1075°K and failed by slip on two (10i0) planes. The approximate orientation of this crystal is illustrated in the figure. Specimens were deformed at 77°K in liquid nitrogen on a tensile machine using an insulated bucket with an internal hook to accept a clamped specimen.

Jan 1, 1961

By C. R. Barrett, N. N. Singh Deo

The high-temperature steady-state creep behavior of a series of dilute copper-silicon alloys was studied to determine the effect of stacking fault energy on the creep-rate. The steady-state creep rate is, when taken at equivalent diffusivities decreases with decreasing stacking fault energy. The stress and temperature dependencies of is suggest that creep is a difusion controlled dislocation climb process. Electron microscopy studies of the creep substructure revealed: 1) the subgrain size is not a function of the stacking fault energy in these alloys, 2) the dislocation density not attributed to the subgrain walls seems to be higher during primary creep and decreases to a lower steady value during steady-state creep, and 3) the dislocation density during steady-state creep decreases with decreasing stacking fault energy. In the past few years numerous investigators have studied the influence of stacking fault energy on high-temperature creep strength. Most of these investigators have confined their attentions to studying the relationship between steady-state creep rate, is, and stacking fault energy, ?, when samples are tested under conditions of comparable stress and temperature. For the case of fcc metals, it was initially shown by Barrett and Sherbyl and since confirmed by many others2"4 that is decreases with decreasing ?, often following an empirical relation of the form i ?m where m is a constant about equal to 3. The application of theory to explain this observation has not been entirely successful. One of the main difficulties has been the almost complete lack of structural information (dislocation density, subgrain size, and so forth) for samples with different stacking fault energies, tested under high-temperature creep conditions. weertman5 has attempted to explain the stacking fault energy dependence of is on the basis of a dislocation climb mechanism. Assuming that both the rate of dislocation core diffusion and the ease of athermal jog formation decreases as ? decreases Weertman has argued that the rate of dislocation climb and hence the creep rate should also decrease as ? decreases. One questionable aspect of Weertman&apos;s analysis is the assumption that core diffusion down extended dislocations is slower than core diffusion down unextended dislocations. The only experimental work done in this area, by Birnbaum et al.6 on nickel and Ni-60 Co, has shown the core diffusivity to increase with decreasing ?. Theories of steady-state creep based on the diffusive motion of jogged screw dislocations often seem unable to predict even the qualitative nature of the es- relationship. Assuming that Weertman is correct in his assumption that the dislocation jog density decreases with decreasing ? then the jogged screw theories predict an increasing dislocation velocity with lower ?. It is usually assumed that the increase in dislocation velocity implies a corresponding increase in creep rate. However, two other factors must be considered before such a statement can be made. That is, we must know how both the mobile dislocation density and the effective stress (the difference between applied stress and internal stress) vary with ?. Significant changes in either one of these factors could outweigh any change in dislocation velocity accompanying a change in ?. And with the slower rates of recovery expected in low stacking fault energy materials it seems likely to expect both mobile dislocation density and effective stress to be dependent on ?. Sherby and Burke7 have suggested that stacking fault energy influences the creep rate in an indirect way. These authors cite evidence that the steady-state subgrain size generated during high-temperature creep is a function of ? decreasing with decreasing ?. Assuming the creep rate to be proportional to the area swept out by each expanding dislocation loop and that subgrain boundaries are good barriers to dislocations, then the creep rate should be proportional to subgrain area, hence increasing as ? increases. A critical evaluation of any of the above theories requires more quantitative information concerning the dislocation substructure generated during high-temperature creep. Accordingly this investigation was undertaken with an aim of studying the influence of stacking fault energy on tbe steady-state creep characteristics of a series of dilute copper-silicon alloys. Special emphasis was placed on studying the strain dependence of both the dislocation configuration and density. MATERIALS AND PROCEDURE Dilute copper-silicon alloys of the compositions shown in Table I were tested in tension at constant stress. The relative stacking fault energy of these alloys has been determined and is shown in Table 11. An Andrade-Chalmers lever arm was used to maintain constant stress and testing was carried out in a water

Jan 1, 1970

By S. S. Arentz

PLANNED health and safety programs have become an essential part of American industry because such programs lead to increased operating efficiency, improved labor relations, better public relations, and to substantial savings in compensation insurance. Those of you who have had the unpleasant duty of informing the wife or widow of one of your men of his serious injury or death while on the job, know that all the benefits of a successful safety program do not show on the balance S. S. ARENTZ, Member AIME, is General Superintendent, Nevada Operations, Combined Metals Reduction Co., Pioche, Nevada. AIME San Francisco Meeting, February 1949. TP 2741 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Jan. 6, 1949. sheet. These programs are of particular importance to the mining ,industry because mining&apos;s reputation as an unusually hazardous industry and the commonly isolated location of mining operations tend to focus attention on these problems. Description of Operations: Before proceeding with a discussion of our health and safety programs at Pioche, it may be proper to give a brief description of Pioche and of our operations there. Pioche is one of the early Nevada mining camps. It was founded shortly after the discovery of high grade silver ore in 1863 and mining has continued with more or less regularity to the present day. In an era of lawlessness, Pioche was notorious. The story persists that 75 men died with their boots on before one died a natural death, and old payroll records show that nearly as many gunmen were employed to stand off claim jumpers as there were miners working the mine. That was probably as close to a safety program as the times permitted. Pioche is situated in southeastern Nevada on the main highway between Ely and Las Vegas. The camp is on the flank of "Treasure Hill," near the original silver discovery, at an elevation of about 6000 ft. The present day population of about 2000 is primarily dependent upon the mines of the area, although Pioche also serves as the county seat of Lincoln Couqty and as the center of the surrounding livestock industry. The camp is served by a branch of the Union Pacific Railroad and receives power from the generators at Hoover Dam. The Pioche operations of the Combined Metals Reduction Co. were started in 1923 when the first complex lead-zinc ore was shipped to the company&apos;s mill at Bauer, Utah. The modern mill at Pioche was completed in 1941. The operations are medium sized in the nonferrous field, employing an average of 350 men in the mine, mill, and related works. The complex lead-zinc ore is mined from replacement deposits in a comparatively flat, extensively faulted, limestone horizon. Mining methods vary from stull-supported open stopes to filled square-set stopes. The thin bedded limestone and shale overlying the ore is allowed to cave as areas are mined out and caving frequently follows closely upon ore extraction. The relatively heavy ground and the numerous faults add to the problems of safe mining. The mine is well mechanized and the mill and surface plant are modern and well equipped. Labor is organized in a C.I.O. union and labor-management relations have been unusually harmonious. During most of the period since 1923 a competent supervisory staff worked to reduce safety hazards but the primary responsibility for safety rested on the individual workman. Accidents happened and all too frequently they were regarded by all concerned as unavoidable. In October 1939, the late Robert L. Dean became superintendent at Pioche. Most of his previous experience had been in the fields of iron and coal mining and from that experience he brought the concept that no accident is unavoidable. Many of the features of our present health and safety programs were initiated by Mr. Dean during his term as superintendent. Health Program: Our health program centers in Dr. Q. E. Fortier and his new, well-equipped, and well-staffed, modern hospital in Pioche. The program starts with a thorough pre-employment physical examination and is followed by yearly re-examinations at the expense of the company. The Pioche Mutual Benefit Association, to which all Pioche mine operators and employees belong, pays benefits covering hospitalization and surgery expense incurred by employee members and their families. The Association is governed by a board of directors elected by its members. The mine operators of the district donated the original capital and pay the monthly dues of the employee members. The employees pay the dues covering members of their families. Though not strictly a part of the

Jan 1, 1951

By S. S. Arentz

PLANNED health and safety programs have become an essential part of American industry because such programs lead to increased operating efficiency, improved labor relations, better public relations, and to substantial savings in compensation insurance. Those of you who have had the unpleasant duty of informing the wife or widow of one of your men of his serious injury or death while on the job, know that all the benefits of a successful safety program do not show on the balance S. S. ARENTZ, Member AIME, is General Superintendent, Nevada Operations, Combined Metals Reduction Co., Pioche, Nevada. AIME San Francisco Meeting, February 1949. TP 2741 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Jan. 6, 1949. sheet. These programs are of particular importance to the mining ,industry because mining&apos;s reputation as an unusually hazardous industry and the commonly isolated location of mining operations tend to focus attention on these problems. Description of Operations: Before proceeding with a discussion of our health and safety programs at Pioche, it may be proper to give a brief description of Pioche and of our operations there. Pioche is one of the early Nevada mining camps. It was founded shortly after the discovery of high grade silver ore in 1863 and mining has continued with more or less regularity to the present day. In an era of lawlessness, Pioche was notorious. The story persists that 75 men died with their boots on before one died a natural death, and old payroll records show that nearly as many gunmen were employed to stand off claim jumpers as there were miners working the mine. That was probably as close to a safety program as the times permitted. Pioche is situated in southeastern Nevada on the main highway between Ely and Las Vegas. The camp is on the flank of "Treasure Hill," near the original silver discovery, at an elevation of about 6000 ft. The present day population of about 2000 is primarily dependent upon the mines of the area, although Pioche also serves as the county seat of Lincoln Couqty and as the center of the surrounding livestock industry. The camp is served by a branch of the Union Pacific Railroad and receives power from the generators at Hoover Dam. The Pioche operations of the Combined Metals Reduction Co. were started in 1923 when the first complex lead-zinc ore was shipped to the company&apos;s mill at Bauer, Utah. The modern mill at Pioche was completed in 1941. The operations are medium sized in the nonferrous field, employing an average of 350 men in the mine, mill, and related works. The complex lead-zinc ore is mined from replacement deposits in a comparatively flat, extensively faulted, limestone horizon. Mining methods vary from stull-supported open stopes to filled square-set stopes. The thin bedded limestone and shale overlying the ore is allowed to cave as areas are mined out and caving frequently follows closely upon ore extraction. The relatively heavy ground and the numerous faults add to the problems of safe mining. The mine is well mechanized and the mill and surface plant are modern and well equipped. Labor is organized in a C.I.O. union and labor-management relations have been unusually harmonious. During most of the period since 1923 a competent supervisory staff worked to reduce safety hazards but the primary responsibility for safety rested on the individual workman. Accidents happened and all too frequently they were regarded by all concerned as unavoidable. In October 1939, the late Robert L. Dean became superintendent at Pioche. Most of his previous experience had been in the fields of iron and coal mining and from that experience he brought the concept that no accident is unavoidable. Many of the features of our present health and safety programs were initiated by Mr. Dean during his term as superintendent. Health Program: Our health program centers in Dr. Q. E. Fortier and his new, well-equipped, and well-staffed, modern hospital in Pioche. The program starts with a thorough pre-employment physical examination and is followed by yearly re-examinations at the expense of the company. The Pioche Mutual Benefit Association, to which all Pioche mine operators and employees belong, pays benefits covering hospitalization and surgery expense incurred by employee members and their families. The Association is governed by a board of directors elected by its members. The mine operators of the district donated the original capital and pay the monthly dues of the employee members. The employees pay the dues covering members of their families. Though not strictly a part of the

Jan 1, 1951

By P. K. Koh, H. A. Lewis, H. F. Graff

New data on the distribution of silicon between slag and carbon-saturated iron at 1600Oand 1700OC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1&apos;700°C for slags containing up to 20 pct A12O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A12O3-SiO, slags over a range from zero pct Al2O3 to saturation with Al2O3, or CaO.2Al2O3. The upper limit of SiO2 is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/Al203 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al,O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al0 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al2O3 and of Al20,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO2 (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2. The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

By H. W. Meyer, H. N. Lander, F. D. Delve

A method of calculating the changes in blast-furnace performance brought about by burden and/or blast modifications is presented. Essentially the method consists of three simultaneous equutions derived from materials and heat balances. These equations can be used not only to evaluate quantitatively the effect of changes in process operating variables on furnace performance, but also to provide a useful means of evaluating changes in process variables which cannot be measured directly. It has been customary for a number of years to use simple heat and materials balances as a basis for assessing blast-furnace practice. A good example of the method used to set up these balances is that proposed by Joseph and Neustatter.1 This approach to process assessment has limited utility, however, in that it cannot be used to predict the furnace coke rate or production under new operating conditions. Using an approach based on multiple correlation of blast-furnace variables, R V. Flint2 has developed an equation which may be used to predict the change in coke rate that will result from some changes in operating conditions with a reasonable degree of accuracy. Although this equation has useful applications in production planning, it cannot be used to study the relationships between the operating variables and the fundamental thermochemi-cal characteristics of the process. In attempting to analyze the blast-furnace process quantitatively, the idea of dividing the furnace into zones3 may at first appear attractive. In our present state of knowledge, however, it is not possible to define with any accuracy the physical limits of such zones in relationship to their temperatures or to the reactions which may occur in them. Although its application is restricted, the zonal approach to blast-furnace analysis is useful in some instances. For example, the change in the calculated flame temperature in the "combustion zone" caused by injecting steam constitutes information which is helpful in understanding why the addition of steam to the blast is best accompanied by an increase in blast temperature. The zonal approach cannot, at the present time, be used to establish the relationships between process variables and process performance if the whole process rather than part of it is to be considered. One of the earliest approaches to the problem of relating blast-furnace operating variables to pro- duction and coke rate was that developed by Marshall.4 Essentially Marshall&apos;s work showed that it was possible to estimate the performance of a furnace by solving three simultaneous equations which consisted of rudimentary carbon and heat balances plus a further equation relating the production, wind rate, and the carbon burned at the tuyeres. Although these equations did not include all of the chemical and thermal variables of the process, their derivation and application seems to be the earliest attempt which achieved any success in relating prior furnace operating data to the calculation of furnace performance under different blast conditions. Work carried out in Germany has been directed mainly towards prediction of coke rates using material and thermal balances rather than statistical methods. wesemann5 used prior furnace operating data as part of the basis for predicting the change in coke rate accompanying a change in burden composition. This author employed a method of successive approximations to estimate the secondary changes in slag volume and stone rate brought about by the change in coke rate. The most recent analysis, which seems to have been developed concurrently with the thermochemical model presented in this paper, has been described by Georgen.6 This author has succeeded in improving on Wesemann&apos;s approach by expressing the total changes in the slag volume and stone rate in terms of the change in coke rate itself. This is accomplished in a manner similar to that used in the thermochemical model described in this paper. Although Georgen makes use of a calculated furnace heat loss, he does not relate the heat loss per unit of hot metal to the production rate as is done in the present work. Georgen&apos;s approach may be used to calculate the changes in materials requirements accompanying changes in furnace operation; it cannot be used to assess the resulting changes in production. The fact that blast-furnace behavior can be interpreted by consideration of the heat requirements of the process was demonstrated by Dancy, Sadler, and Lander.7 In the analysis of blast-furnace operation with oxygen and steam injection these authors showed that it was possible to account for the changes in production and coke rate

Jan 1, 1962

By Francis R. Conley, John A. Sievert, John N. Dew

A brief review is presented of the past performance of a number of large, thin, highly permeable reservoirs with low dips in the Bolivar Coastal fields of Venezuela. The performance of these reservoirs indicates that the fluids are segregated vertically within the sand section by gravity. With this assumption, equations are developed which describe the performance under pressure maintenance operations. Methods of solving these equations and results of simple example calculations are presented. Example calculations indicate that under pressure maintenance conditions injected gas tends to {tow preferentially along the top of the sands and that encroaching water has a tendency to flow preferentially along the bottom. The expected performance of segregated fluids is discussed and compared with that of fluids which are uniformly distributed in any sand section. INTRODUCTION The field performance of a number of reservoirs described herein indicates that the fluids are segregated vertically within the sand section by the force of gravity. Thus, it was felt that any method used to predict the future performance of these reservoirs should consider the effects of segregation in the sand sections. A study of the available information on some of the reservoirs suggests that increased recoveries may be expected if the reservoir pressure is maintained by either crestal gas injection or flank water injection. To predict future performance of reservoirs under pressure maintenance operations, a method of analysis was needed which would account for segregation of fluids in the sand sections. Several methods of analysis have been developed to take into account the segregation of fluids in the reservoir as a whole1,3 To our knowledge no method considers segregation of the fluids within sand sections in the manner indicated by the past performance of several reservoirs in the Mara-caibo Basin. This paper outlines part of the work done in studying some of these reservoirs and contains a description of their performance characteristics. The analysis presented is restricted to pressure maintenance conditions, since space limitations prevent a full discus- sion of the development of the mathematical relations and the various methods of solving them. Only a sketch of the development of the mathematical relations is given. The various methods of solving these relations are pointed out, but the actual determination of solutions to various problems are omitted except for one example. It is felt that these results may aid in the study of reservoirs outside the Maracaibo Basin. Some concepts on which the present analysis is based are outlined by D. N. Dietz. However, the analysis presented herein includes several factors not considered by Dietz: (1) variations in permeability and in the cross section, (2) various shapes of the cross section, and (3) the production of fluids. Also, the mathematical development presented by Dietz differs considerably from our corresponding analysis. RESERVOIR CHARACTERISTICS The reservoirs under consideration, large and thin, with low dip and high permeability, are large to the extent that they contain from 0.5 to over four billion bbl of oil initially in place. The section thicknesses vary from 100 to 400 ft and the lengths from 10,000 to 40,000 ft. Thus, a length-wise cross section of the producing formation appears to be long and thin. The dip angles vary from 0 to 6 degrees and the average permeabilities vary from 0.5 to over three darcies. The reservoirs contain from 20 to 50 per cent shale inter-laminated with the productive sands. Most shale breaks within the major sands do not correlate from one well to the next, and correlation is often difficult, even between wells drilled from the same location. However, it is often possible to correlate the shale breaks between major sands for some distance. Herein we are concerned with the performance of reservoirs containing oil of gravities over 20" API. Past reservoir performance indicates good pressure communication and, in cases where pressure sinks have developed, large amounts of fluid migration have occurred. Few of the reservoirs have had initial gas caps, but also, few have been found to be highly under-saturated. Due to gravity segregation, secondary gas caps usually form before the pressure has been reduced more than 25 per cent of its initial value. The effect of gravity has not only been apparent on a reservoir-wide basis, but has also caused segregation of the reservoir fluids in productive sections. Proof of this is found from the results of selective well tests, workovers, and electric and various other types of logs. Evidence that

By D. L. Kelley

High-viscosity water injection has been proposed for use in reservoirs containing high-viscosity crude oils. Previous publications have largely ignored the possible effects of the connate water on the proposed process. This paper describes experimental work which indicates that the connate water will be forced ahead of the injected water to form a bank of low-viscosity water. This decreases the oil recovery which would be expected if such a bank were not formed. These effects are shown for a range of fluid mobilities and connate-water saturations for a five-spot injection system. In general, oil recoveries using viscous water are significantly greater than for untreated water even though they are less than would be expected if no connate water bank were formed. INTRODUCTION The effect of mobility ratio on the oil recovery of wa-terfloods has been known for many years. Muskat first pointed out that the fluid mobilities (k/µ) in the oil and water regions would affect the performance of the water-flood, and he estimated the general effect of these variables.&apos; Since this early work, studies of the effect of mobility ratio on secondary recovery have been reported where mathematical,&apos; potentiometric3 and scaled flow models&apos; were used. These studies have shown that a reduction in the mobility ratio between the oil and the displacing fluid would cause additional oil recovery when water-flooding reservoirs containing viscous crude oils. Studies reported by Pye- nd Sandiford 8 have indicated that chemicals to increase injection water viscosity are now available and can be used to reduce the over-all mobility ratio of a waterflood. Where mobility ratios are controlled by the injection of viscous fluids, the connate water of the reservoir can play an important part in the displacement of the reservoir oil. The purpose of this study was to determine the effect of the connate-water saturation in waterfloods where viscous waters are used for injection. DISPLACEMENT OF THE CONNATE WATER Russell, Morgan and Muskat7 were the first to recognize the mobility of connate waters in waterflooding. They conducted waterfloods on oil-saturated cores containing 20 and 35 per cent irreducible water saturations, and found that from 80 to 90 per cent of the "irreducible" water was produced after only one pore volume of water was injected. However, their experiments were conducted at rates of flow significantly higher than those ordinarily occurring in waterfloods. Also, the cores were only from 4.0 to 8.5 cm long. Brown 4 studied a 100-cm linear sand pack which had been prepared to contain connate water and oil. He used 140- and 1.8-cp oils with injection water of essentially the same viscosity as the connate water. He found that all of the connate water was displaced by the injection water in both cases. However, the injection volumes required for complete displacement of the connate water were considerably higher in the case of the more viscous oil. To verify the results of the foregoing experiment, a 10-ft-long linear model was constructed by packing 250-300 mesh sand in a 1/2-in. diameter nylon tube. The model was evacuated, saturated with a brine of 1-cp viscosity, and flooded with a 41-cp mineral oil to the irreducible water saturation of 10.9 per cent. The model was then waterflooded by the injection of a water solution which had an apparent viscosity of 42.6 cp. The solution consisted of 0.5 per cent methylcellulose in distilled water. The viscosities of the oil and connate water were measured with an Ostwald viscosimeter. The viscosity of the polymer solution was calculated by Darcy&apos;s law using pressures measured during actual flow conditions. The ratio of the mobility in the oil region to the mobility in the inject ion-water region was approximately 0.32. The mobility ratio of the oil region to the connate-water bank was approximately 14. The mobility ratio between the connate-water bank and the injection water region was 0.024. Approximately 84.5 per cent of the recoverable oil was produced before water breakthrough. Immediately following breakthrough, oil and connate water were produced at an increasing water-oil ratio until the viscous injection water broke through. At viscous-water breakthrough, 96 per cent of the original connate water had been produced. After breakthrough of the viscous water, there was no additional production of connate water or oil. The near-

Jan 1, 1967

By F. Weinberg

The relative concentration of 1" at grain boundaries in controlled orientation bicrystals has been examined by autoradiographic techniques, and by activity measurements of grain boundary surfaces exposed by preferential ,melting. The autoradio-graphs indicate that thallium is concentrated at grain boundaries in as-grown bicrystals, but not in zcell-annealed bicrystals. They also indicate that the solute concentration and the distribution on as-grown bicrystal surfaces are markedly different than that of the bulk material. The boundary surface measurements are in agreement with the autovadiographic evidence. On the basis of these measurements, as-grown bicrystals containing approximately 100 ppm of Tl, solidified at rates between 5 and 30 cm per hr and with tilt boundaries greater than 10 deg, exhibited grain boundary segregation equivalent to roughly 10 atomic planes of pure solute. Higher solute concentrations (equivalent to 140 atomic planes of pure solute) were obtained in bicrystals solidified slowly (0.6 cm per hr); slightly higher values were obtained in specimens containing a large angle nantilt boundary. Annealing for various times over a range of temperatures eliminated grain boundary segregation within the experimental uncertainty of the results (equivalent to 1 atomic Plane of pure thallium at the boundary). The results for the as-grown bicrystals can be qualitatively accounted for by assuming the presence of a groove on the solid-1iq;id interface, at the grain boundary. SOLUTE segregation at grain boundaries may be considered in two parts, namely, nonequilibrium segregation associated with the solidification process, and equilibrium segregation in fully annealed materials.&apos; There is much indirect evidence for nonequilibrium segregation, based on preferential etching at grain boundaries and the mechanical properties of as-cast alloys. In addition, some direct observations have been reported in which radioactive tracers were used as solute additions and segregation detected at the grain boundaries by autoradiographic techniques. However, there is little detailed quantitative data on solute concentrations related to grain boundaries, particularly for different freezing conditions and grain boundary configurations. Equilibrium segregation at grain boundaries has been considered both theoretically and experimentally. cean&apos; has made an estimate of the maximum equilibrium solute concentration that might be expected at a grain boundary, based on the lattice distortions in the boundary region. He arrived at a concentration which was equivalent t a monatomic layer of pure solute. A similar value, based on thermodynamic arguments, was calculated by Cahn and Hilliard for the segregation of phosphorus in iron. Experimentally, much higher values of solute concentration at grain boundaries have been reported recently by both Inman and iler&apos; for phosphorus in iron, and Ainslie et 1.&apos; for sulfur in iron. They observed concentrations equivalent to as much as 20 to 100 atomic layers of pure solute at the grain boundaries. However, in both cases it was shown that the observed segregation was not due solely to equilibrium segregation at the grain boundary. In the former case, precipitation effectss due to trace impurities in the material were believed to account for the large amount of solute present at the grain boundary. In the latter case it was shown that a high density of dislocations in the boundary region could provide a large number of additional sites for solute atoms, other than at the grain boundary. Thomas and chalmera have reported on the equilibrium segregation of po210 in grain boundaries of Pb-5 pct Bi alloys. Using autoradiographic techniques, they observed a concentration of polonium along the boundary trace on the surface of annealed bicrystal specimens grown from the melt. The concentration only appeared after annealing, and varied with boundary angle, increasing as the boundary angle increased. Their conclusions have been questioned by Ward," who pointed out that the segregation they observed along the boundary trace was much too wide to be compatible with the usual concepts of the thickness of a grain boundary of several lattice spacings. Also, Maroun et al.,l1 with specimens similar to those of Thomas and Chalmers, found that segregation could only be detected on the specimen surface, suggesting that Thomas and Chalmers&apos; results were associated with an oxidation effect of polonium, and not equilibrium segregation. Thomas and Chalmers replied12 that they did observed segregation at the grain boundary in the bulk material and suggested further experiments were necessary to resolve the difference. The purpose of the present investigation was to examine both nonequilibrium and equilibrium grain boundary segregation in melt grown bicrystal specimens as a function of boundary angle, growth rate, and solute concentration, and to de-

Jan 1, 1963

By Ralph Hultgren

IN solid solutions atoms of differing sizes occupy the same crystalline lattice, requiring that some of them be compressed and others expanded. The energy involved has been called misfit strain energy and is an important concept of crystal chemistry. If the atomic sizes and elastic constants of interatomic bonds are known, the misfit energy may be calculated,&apos; provided certain simplifying assumptions are allowable. Usually, isotropic crystals are assumed and interatomic distances are taken to be the statistical average determined from X-ray diffraction. Such calculations yield values of the misfit energy of the order of 1 or 2 kcal per atom in alloys such as Au-Cu at compositions of 50 atomic pct. However, evidence has accumulated in recent times that atoms change their sizes with composition of alloys, implying electronic rearrangement of the bonds. The size changes have been found particularly by application of the X-ray method developed by Warren, Averbach, and Roberts.&apos; Thus, Averbach, Flinn, and Cohen3 determined radii in Au-Cu alloys. Oriani4 showed that these new radii led to a calculated misfit energy in disordered AuCu, which was decreased from the values calculated by the usual theory more than twenty-fold, to only 80 cal per g atom. Thermodynamic calculations from the phase diagram5 also show misfit energy to be no more than a few hundred calories per g atom in this alloy. The question of what electronic rearrangements are possible therefore becomes compelling in estimating misfit energy. In the following pages the results of certain calculations on the AuCu tetragonal superlattice are submitted. Conclusions drawn from these should be applicable in large degree to disordered solid solutions. As in all ordered states, bonding distances in the superlattice are individually known, rather than being merely average distances as found from lattice constants of disordered states. Moreover, only the Au-Au and Cu-Cu distances are strained; the elastic constants of these are known in the elementary state. In the usual calculation it is necessary to assume elastic constants for Au-Cu bonds. Misfit energy has thus been calculable without the need of many simplifying assumptions usually made. It is still assumed that equilibrium bond lengths and elastic properties of the bonds are the same in the alloy as in the pure metals. As previously discussed, this is probably not correct. Also assumed is that the bonds are not affected by strain of neighboring bonds. A calculation of Young&apos;s modulus from compressibility data shows this to be far from true; extensive electronic rearrangements take place. It would seem that misfit energy cannot be calculated from elasticity data for the elements. The usual methods may, however, give an upper limit which is often much higher than the true value. The question of electronic rearrangement is, of course, a complex one. Pauling&apos;s theory gives a simple, approximate treatment of the relation between type of bond and bond distance. This has been applied with some success to the Au-Cu system, as will be shown in a later section. Misfit Energy in Au-Cu Alloys Hume-Rothery and Raynor6 discuss the Au-CU system as a type example of strain energy. The gold atom is 12.8 pct larger in diameter than the copper atom, near the size factor limit beyond which solid solubility is severely restricted. They therefore consider the misfit energy to be large, a conclusion for which they believe they find evidence in the phase diagram. Gold and copper are completely miscible in the solid state, but the alloy has a minimum melting point at an intermediate composition. From this Hume-Rothery and Raynor conclude that the strain energy is nearly large enough to prevent miscibility; the phase diagram tends toward a eutec-tic type. In Ag-Cu, which has almost identical size relationships, solid miscibility is quite limited; whereas in Au-Ag, where atomic sizes are nearly the same, there is complete miscibility without a minimum in the melting point. From their arguments the heat of formation of Au-Cu would be expected to be endothermic or only slightly exothermic, that of Ag-Cu to be endothermic, and that of Au-Ag to be exothermic. Deviations, from Ve-gard&apos;s law of additivity of atomic radii support these conclusions, since Au-Cu and Ag-Cu both have pronounced positive deviations, and Au-Ag has a negative deviation. Nevertheless, Au-Cu alloys form exothermically; indeed, considerably more exothermically than Au-Ag, Table I. Hence, strain energy must be much less important in this case than Hume-Rothery and Raynor have supposed.

Jan 1, 1958

By C. Richard Tinsley

Like most minerals, coal is inherently a demand-limited commodity. The very sedimentary nature of its occurrence implies greater availability potential than demand. But this situation is overridden by economics among fuels, between coals, and within coal blends. Such considerations make coal forecasting a very hazardous profession indeed. THERMAL COAL If one thought that the lead times involved with a mining project were very long, one has obviously not been exposed to the planning process in the electric generation business - a process seriously confounded by shifts in load growth, environmental pressures, capital intensity, security of fuel sourcing, inter-fuel economics, and so on. But as a general rule, the near-term forecasts for thermal coal can reliably be based on a bottom-up, plant-by-plant analysis. Cement plant conversions can also be reasonably estimated next in order of reliability, although they have a much wider spectrum of coal qualities and fuel sources to choose from with a notably higher tolerance for sulfur and ash. Finally, industrial demand can be assembled from the estimates for conversions by pulp/paper plants, chemical plants, etc. The industrial sector is harder to estimate, since it may involve small boilers or dual-fired units. Assessing demand in the Pacific Rim is relatively a straightforward process in the near term because the major importing countries are all located on the Asian continent with either negligible or very minor (yet stable) indigenous coal production, (itself often operated on a subsidized basis). Furthermore, all imports are seaborne. These major importers are Japan, Korea, Taiwan, and Hong Kong with Thailand, Singapore, and Malaysia up-and-coming consumers. The suppliers to this market all have substantial reserves to back up decades of exports to these countries. Australia, the US, Canada, South Africa, China, and the USSR dominate the supply side. The second oil-shock of 1979/1980 has convinced the importers that reliance on oil can be expensive and eminently interruptible. Thus, they are determined to diversify away from oil&apos; to nuclear and coal for generating electricity and for coal for other purposes where possible. This trend is seen to continue even in the face of the oil glut worldwide and oil-price reductions in early 1982. But the importers are also convinced that reliance on one coal source and, in particular, one infrastructure route for the coal chain from mine to consumer can be equally expensive and interruptible. Strikes in the US and Australia; excessive demurrage at certain ports; relegation of coal to a lower priority on multiple-use railroads in the USSR and China; and concern over escalation on high-infrastructure or high-freight coal chains are among the risks worrying the importers. As a consequence, Pacific Rim thermal coal purchases are being allocated among supplier nations, between ports, and within each country. An example of Japan&apos;s shift away from Australia and toward the US and Canada is shown in the estimates in Table 1. But the confidence of the import estimates deteriorates sharply beyond the plant conversion timetables and construction schedules in the near term. If part of the second generation of coal-fired power plants can handle lower-energy coals, the field of suppliers could widen to accept sizeable tonnages from Alaska, Wyoming, Alberta, or New Zealand resources. These supply sources generally have some infrastructure or freight advantage to compensate for their lower quality and to compete on a delivered energy-unit basis. These also offer diversification in sourcing. And the possibility of coal liquefaction in Japan further widens the sourcing network. A great number of Pacific Rim coal forecasts have been generated, especially for Japanese thermal-coal imports which are expected to grow strongly in the 1980&apos;s. Since the Japanese themselves have not yet settled their energy policy, the exact numbers are hard to call. Nevertheless, at 50 million tonnes of imports in 1990, Japan would consume 50-60% of the total Asian thermal coal imports as shown on Tables 2 and 6. The next most important consumers are the "island" nations of Korea, Taiwan, and Hong Kong (see Tables 3-5). All three are embarking on power plant developments usually with captive unloading facilities, capable of accepting more than 100,000-dwt vessels. Korea, with no-indigenous bituminous coal, is not especially enamoured with US coals, which are deemed too heavily loaded by freight and infrastructure costs -- up to 70% of the delivered price. Thermal coal contracts are presently split to Australia (70%) and to Canada (30%). Korea Electric Power Co. is already considering second-generation boilers capable of burning lower-quality coals than the present standard. Korea does burn domestic anthracite.

Jan 1, 1982

By A. Muan

Liquidus data are presented for mixtures in the ternary system FeO-Fe2O3-SiO2 in equilibrium with a gas phase with O2 pressures ranging from 10-10.9 to 1 atm. Data obtained are combined with previously published data to construct lines of equal 02 pressures and lines of equal CO2/H2 mixing ratios along the liquidus surface. Courses of crystallization of selected mixtures under conditions of constant total composition, constant O2 pressures, and constant CO2/H2 mixing ratios are discussed. PHASE equilibrium studies of silicate systems where iron is one component are complicated by the fact that iron readily occurs in three different states of oxidation: Fe3+, Fe2+, and Fe0. Success or failure in work with iron silicate systems is to a large extent dependent on control of the oxidation state of iron and all investigations therefore must be carried out under carefully controlled atmospheric conditions. Silicate systems containing only strongly electropositive metals (like Na+, Ca2+, Mg", etc.) can, for simplicity, be treated as condensed systems, that is, the gas phase can be neglected and the phase relationships discussed in terms of the phase rule written in the well known simplified form P + F = C + 1. In the case of iron silicate systems, however, the composition of the condensed phases varies with the gas composition, and a complete picture of phase relationships can be obtained only by varying the gas composition over a wide range. In order to understand the phase relationships in the more complicated multicomponent silicate systems with iron oxide as one of the constituents, a knowledge of the ternary system FeO-Fe2O3-SiO2 is essential, since it constitutes a bounding portion of all such systems. It was with this in mind that the present study was undertaken. Previous Work A considerable amount of work has been done on various aspects of the chemistry and metallurgy of systems containing silica and iron oxides. The two bounding binary systems FeO-Fe2O3 and FeO-SiO2" The first attempt to obtain information on phase relationships of iron oxide-SiO, mixtures at different 0, pressures was made by Greig.&apos; Darken" determined the melting points of iron oxide on solid silica under various atmospheric conditions. Darken did not determine experimentally the composition of the melts at liquidus temperatures but discussed very ably the principles involved in applying the phase rule to the system. In a recent study Schuhmann, Powell, and Michal8 determined experimentally the liquidus surface of a portion of the ternary system and combined the new information with data in the literature to construct a phase diagram. Their method was briefly as follows: Homogeneous mixtures with various contents of SiO2, FeO, and Fe2O3 were made up by melting together stock mixtures in various proportions. Samples of the homogeneous mixtures, the compositions of which were determined by chemical analysis, were then heated in platinum crucibles in an inert atmosphere until equilibrium among the condensed phases was achieved. The samples were quenched to room temperature and the phases present determined by microscopic examination. Assuming that no change in composition takes place during the equilibration run in inert atmosphere, the liquidus surface can be determined, but no information is obtained regarding the partial pressures of 0, of the gas phase in equilibrium with the condensed phases. The author&apos;s method, to be described in the next section, permitted the location of points at the liquidus surface as well as a calculation of the corresponding partial pressures of O2. Experimental Method General Procedure: The standard quenching technique was adapted for a study under controlled variable atmospheric conditions. Premelted mixtures of silica and iron oxides in platinum envelopes were held at constant temperature under chosen atmospheric conditions until equilibrium was reached among solid, liquid, and gas phases. The sample was then quenched to room temperature, the phases present identified, and, for the most significant runs, the composition was determined by chemical analysis. The corresponding partial pressure of 0, was calculated from known equilibrium constants of the gas reactions occuring in the furnace atmosphere. Materials: Starting materials were oxides of commercially highest available purity; cp silicic acid was dehydrated by heating to 1350°C for 6 hr and cp Fe2O3 was dried at 400° C for the same length of time. Samples of 10 g were made up by mixing

Jan 1, 1956

By H. W. Mossman

Three aspects of magnetite smelting are discussed. The first is the working out of equilibrium conditions for eliminating sulfur. The second is the influence of magnetite solubility on the difficulty of tapping the reverb matte. The third is an approximation of the equilibrium conditions in the reverb gases which govern whether magnetite is mode or reduced in the reverb slag by these gases and by any iron sulfide in the slag. MAGNETITE has had a varied history in the Hurley Smelter since its start in 1939. Magnetite determinations on the smelter products are made regularly only on the monthly composite samples. Variations on the monthly averages are shown in Table I. Magnetite which drops from the slag and matte in the reverb has some slight bottom buildup which comes and goes, but no substantial accumulation from this source has been found at the end of a normal nine months&apos; furnace campaign. However, there has been some low grade magnetite bearing material mixed with considerable A1,0,, which has slid down from the bottom of the sloping flue between the reverberatory furnace and the waste heat boilers. This accretion has required drilling and blasting near the skimming end of the furnace. The magnetite has interfered with tapping at times. When the smelter was first started, tapping trouble from magnetite was extremely severe. Increasing the reverberatory furnace temperature by putting in an air preheater and a Dutch oven has helped greatly, although there still is occasional tapping trouble. When the present series of physical chemistry articles on copper smelting started coming out in 1950, they were read with interest, but no immediate application was seen for them. Results of some laboratory work in 1952 aroused a much stronger interest in this physical chemistry. A series of melts was made on some converter slags, which had magnetite in very large grain sizes, with the object of reducing the grain sizes in the slag, as it was known that it was easier to handle in the reverb in that condition. Anything done in the tests greatly reduced the grain sizes—even in the controls, where nothing was done except melt the slag and cast it. There was more magnetite in the slags after the tests than before, and with wide variations. There were no obvious reasons lor much of what happened in these tests. Much of the base material published in English in this field was made available for study. Recalculations were made on many of the type problems, and part of the data was reduced to local temperatures and compositions. Explanations were found for what happened in the 1952 series of tests on converter slags, and the same principles turned out to be a description of much of what magnetite does in the reverb. This article is to present the results of that study, from the viewpoint of applying the technical material in definite numerical form to the operating conditions in both the converters and the reverberatory furnaces at the Hurley smelter. Table I. Magnetite Variations on Monthly Averages, 1939 to 1955 Pet Magnetite Lowest Highest Average Converter slag 13.6 43.3 25.4 Roverb slaa 2.7 20.9 8.7 Matte 28 15.9 98 In general it was found that magnetite is made or reduced in both the converters and the rever-beratory furnace, depending on variations of temperature, matte composition, and reverb gas composition occurring in ordinary plant operation. Within reasonable limits, the field conditions for formation or reduction can be predicted, and probably can be set up and maintained. Converter conditions affecting magnetite formation can be put into numerical values better than for the reverb from purely technical calculations. The converter can be operated so as to keep the magnetite in the slag down to between 12 and 14 pct and still give satisfactory life for the converter brick. This depends upon having converter flux available which will make a slag with a good separation without raising the temperature too high. In the Hurley reverb and others with similar conditions, it is likely that a compromise of conditions will give a reasonably good control of combustion and still keep the magnetite from building up on the bottom. This discussion consists of three main parts. The first is the working out of the equilibrium conditions in the converter for determining in which direction the reaction 3 Fe,,O, (s) + FeS (1) F? 10 FeO (1) + SO, will go under actual converter operating conditions. The second deals with the influence of the solubility of magnetite in the slag and matte in the reverb on the difficulty of tapping matte. The third is an approximation of the equilibrium conditions in the

Jan 1, 1957

By A. Bauer, P. Calder, N. H. Carr, G. R. Harris

Since both rotary and jet piercing drills are used by the Iron Ore Co. at Smallwood, it is often desirable in planning to know in which regions of the orebody or new orebodies a particular drill will be the most economic. This makes it necessary to establish a correlation between drillability and pierceability and some physical rock properties. For rotary drills a good correlation was found with penetration rate and grinding factor index. The jet piercers were found to have a reciprocal relationship in the sense that the best rotary ground was the worst jet ground and vice versa. It is also indicated how an economic comparison could be made using these penetration rate versus grinding factor index curves, the hole size distribution curves for single pass and chambered holes and the mine distribution curve for grinding factor index. A discussion is presented on the fuel oxygen ratios to be used in jet piercing and on the site gas sampling and analysis which has been used to set up the drills. The fuel has been cut back so that stoichio-metric conditions exist, carbon monoxide is drastically reduced and pop-up or exploding holes eliminated. No decrease in penetration rate has been observed contrary to the published results of previous workers. The blasting procedure and results at Smallwood are discussed and the operation of Iron Ore Co.&apos;s slurry pump-mix truck is also described briefly. Smallwood mine is part of the Iron Ore Co.&apos;s Carol Lake operation and is situated in Labrador, 240 miles north of Sept-Iles, Quebec. Last year 15 million tons of crude ore were crushed to yield 6.3 million tons of concentrate and pellets. This year the figures will be 17 million tons of crude and 7% million tons of concentrate and pellets which is the full plant capacity. Carol Lake ores consist primarily of specularite and magnetite mixed with quartz. For convenience the ore has been split-into the following classifications depending on the percentage of magnetics in the sample, shown in brackets: specularite (0 to 10%), specularite-magnetite (10 to 20%), magnetite- specularite (20 to 30%), magnetite (>30%). The order of classification also represents the order of increasing grinding difficulty - the specularite generally being the easiest and the magnetite the hardest. The orebody also contains a small percentage of waste materials consisting of limonite carbonate, quartz carbonate and quartz magnetite. The first two materials are among the softest in the mine, generally softer than the specularite, and the quartz magnetite is amongst the hardest. The bulk of the material in the mine is of the specularite-magnetite and magnetite-specularite classifications. As a result of test drilling at Smallwood in 1960 with rotary, jet and percussion drills, the Iron Ore Co. purchased four JPM-4 jet piercers for the bulk of production drilling and set up an oxygen plant to supply 20 tons of oxygen per day. This oxygen is sufficient for two machines operating full time and one part time. In addition, there are two 50-R, one 60-R and one 40-R machines in use. The benches are 45 ft high and 50 ft holes are generally drilled. JET DRILLING At the onset of jet drilling in the late fall of 1962, two major problems were encountered: 1) freezing due to winter operations; experience and the use of heat at more places, such as the rotary head, has eliminated this,&apos;" and 2) exploding or "popping" drilled holes; this happened frequently (several holes "popping" each day) and was the cause of two lost time accidents. In one instance a hole was being measured with a tape which fell down the hole causing it to "pop." Safety glasses though pulverized saved the wearer&apos;s eyesight. Various methods were then employed to detonate the holes before measuring or loading (dropping lighted rags of fusees down, or sparking across a spark gap). These methods were time consuming and far from completely successful. Consideration was given to the fuel oxygen ratio on the machines and what this would produce in the way of product gases. A fuel oxygen weight ratio of 0.35 which was quite oxygen negative was being used. Theoretically appreciable carbon monoxide would be produced at this fuel oxygen ratio. On the close down procedure of the jet which calls for low oxygen after flame out, oxygen would be left in the hole along with this carbon monoxide. This is an explosive mixture. The fuel oxygen ratio was cut back to stoichiometric

Jan 1, 1967

By Takashi Katsura, Avnulf Muan

Equilibrium relations in the system FeO-Fe2O3 Cr2O3 have been determined at 1300°C at oxygen pressures ranging from that of air (0.21 atm) to 1.5 x 10-11 atm. The following oxide phases have stable equilibrium existence under these conditions : a sesquioxide solid solution with corundum-type structure (approximate composition Fe2O3-Cr2O3); a ternary solid solution with spinel-type structure (approximate composition FeO Fe2O3-FeO Cr2O3) and a ternary wüstite solid solution with periclase-type structure and compositions approaching FeO. The metal phase occurring in equilibrium with oxide phase(s) at the lowest oxygen pressures used in the present investigation is almost pure iron. The extent of solid-solution areas and the location of oxygen isobars have been determined. ThE system Fe-Cr-O has attracted a great deal of interest among metallurgists as well as ceramists and geochemists. Metallurgists have studied the system because of its importance in deoxidation equilibria, ceramists because of its importance in basic brick technology, and geochemists because of its importance for an understanding of natural chromite deposits. Chen and chipman1 investigated the Cr-O equilibrium in liquid iron at 1595°C in atmospheres of known oxygen pressures (controlled H2O/H2 ratios). The main purpose of their work was to determine the stability range of the iron-chromite phase. Hilty et al.2 studied oxide phases in equilibrium with liquid Fe-Cr alloys at 1550°, 1600°, and 1650°C. They reported the existence of two previously unknown oxide phases, one a distorted spinel with composition intermediate between FeO Cr203 and Cr3O4, the other Cr3O4 with tetragonal structure. They also sketched diagrams showing the inferred liqui-dus surface and the inferred 1600°C isothermal section for the system Fe-Cr-O. Koch et al3 studied oxide inclusions in Fe-Cr alloys and also observed the distorted spinel phase reported by Hilty et al. Richards and white4 as well as Woodhouse and White5 investigated spinel-sesquioxide equilibria in the system Fe-Cr-O in air in the temperature range of 1420" to 1650°C, and Muan and Somiya6 delineated approximate phase relations in the system in air from 1400" to 2050°C. The present study was carried out at a constant temperature of 1300° C and at oxygen pressures ranging from 0.21 atm (air) to 1.5 x 10-11 atm. The chosen temperature is high enough to permit equilibrium to be attained within a reasonable period of time within most composition areas of the system, and still low enough to permit use of experimental methods which give highly accurate and reliable results. These methods are described in detail in the following. I) EXPERIMENTAL METHODS 1) General Procedures. Two different experimental methods were used in the present investigation: quenching and thermogravimetry. In the quenching method, oxide samples were heated at chosen temperature and chosen oxygen pressure until equilibrium was attained among gas and condensed phases. The samples were then quenched rapidly to room temperature and the phases present determined by X-ray and microscopic examination. Total compositions were determined by chemical analysis after quenching. In the thermogravimetric method, pellets of oxide mixtures were suspended by a thin platinum wire from one beam of an analytical balance, and the weight changes were recorded as a function of oxygen pressure at constant temperature. The data thus obtained were used to locate oxygen isobars. The courses of the latter curves reflect changes in phase assemblages and serve to supplement the observations made by the quenching technique. 2) Materials. Analytical-grade Fe2O3 and Cr2O3 were used as starting materials. Each oxide was first heated separately in air at 1000°C for several hours. Mixtures of desired ratios of the two oxides were then prepared. Each mixture was finely ground and mixed, and heated at 1250" to 1300°C in air for 2 hr, ground and mixed again and heated at the same temperature for 5 to 24 hr, depending on the Cr2O3 content of the mixture. A homogeneous sesquioxide solid solution between the two end members resulted from this treatment. A Part of some of the sesquioxide samples thus prepared was heated for 2 to 3 hr at 1300°C and oxygen pressures of 10-7 or 1.5 x 10-11 atm. Reduced samples (either iron chromite

Jan 1, 1964

By R. H. Gautschi, F. C. Langenberg

Rare-earth additions were made to laboratory heats of Type 310 stainless to observe their effect on as-cast ingot structure, nitrogen and sulfur contents, and nonmetallic inclusions. Lanthanum had a grain-refining effect in 30-lb ingots, but results with 200-lb ingots were inconsistent. Cerium, lanthanum, and misch metal lowered the sulfur content when the sulfur exceeded 0.015 pct and the rare-earth addition was greater than 0.1 pct. The rare-eardh content in the metal dropped very rapidly within the first few minutes after the addition. The size, shape, and distribution of nonmetallic inclusions was not changed in 30-lb ingots, but changes were noticed in larger ingots. RARE-earth* additions have been made to austenitic Cr-Ni and Cr-Mn steels to improve their hot workability. The high alloy content of these steels often results in a considerable resistance to deformation and inherent hot shortness at rolling temperatures, particularly in larger ingots. Rare earths in the metallic, oxide, or halide form are usually added to the steel in the ladle after deoxidation although they can be added in the furnace prior to tap or in the molds during teeming. The literature- indicates that the effects of rare-earth treatments on these stainless steels are not consistent, and sometimes even contradictory. Since no mechanism has been presented which satisfactorily accounts for the claimed improvements, the effects of rare earths are a qualitative matter. The work described in this paper was initiated to expand the knowledge of the effects of rare-earth additions on melting variables such as ingot structure, chemical analysis, and nonmetallic inclusions. REVIEW OF LITERATURE Ingot Structure—Rare-earth additions to stainless steels have been reported to cause a change in primary ingot structure in that there are fewer coarse columnar grains. However, the results are inconsistent. While one investigation1 has shown a large reduction in coarse columnar crystals, another2 has been unable to observe this effect, particularly when small ingots were poured. Post and coworkers3 observed ingot structures for a number of years and found that the columnar type of structure is not definitely a cause of any particular trouble in rolling or hammering, provided the alloy is ductile. Knapp and Bolkcom4 found rare-earth additions to be quite effective in preventing grain coarsening in Type 310 stainless steel. Chemical Analysis—Many effects of rare-earth treatment on chemical analysis have been claimed in the literature. Russell5 observed that some sulfur is removed by rare-earth metals, and that a high initial sulfur content improved the efficiency of sulfur removal. Lillieqvist and Mickelson6 report that rare-earth treatment causes sulfur removal in basic open-hearth furnaces, but not in basic lined induction furnaces. Knapp and Bolkcom found no sulfur removal in acid open-hearth and acid electric furnaces, probably because the acid slag can not retain sul-fides. snellmann7 showed that sulfur could be lowered apprecfably with rare-earth additions; however, a sulfur reversion occurred with time. Langenberg and chipman8 studied the reaction CeS(s) = Ce(in Fe) + S(in Fe), and found the solubilit product [%Ce] [%S] equal to (1.5 + 0.5) X 10-3&apos;at 1600°C. Results in 17 Cr-9 Ni stainless were about the same as those in iron. Beaver2 treated chromium-nickel steels with 0.3 pct misch metal and observed some reduction in the oxygen content. He also noted an inconsistent but beneficial effect of rare earths when tramp elements were present in amounts sufficient to cause difficulty in hot working. It is not known whether rare earths reduce the content of the tramp elements or change the form in which these elements appear in the final structure. No quantitative data are available concerning a possible effect of rare-earth treatment on hydrogen and nitrogen contents. However, Schwartzbart and sheehan9 stated that additions of rare earths had no effect on impact properties when the nitrogen content was low (0.006 pct), but served to counteract the adverse effects of high nitrogen content (0.030 pct) on these properties. Knapp and Bolkcom4 analyzed open-hearth heats in the treated and untreated conditions and found the nitrogen content (0.006 pct) to be unaffected. These two results lead to the speculation that rare-earth additions can reduce the nitrogen content to a certain level. Decker and coworkers10 have observed that small amounts of boron or zirconium, picked up from magnesia or zirconia crucibles, increased high-tem-

Jan 1, 1961

By R. W. Stormont, F. Wald

The phase diagram of the Pseudobinary section PbTe-Fe was determined. It was found to contain a monotectic and a eutectic reaction, the latter one taking place at 14 at. pct Fe and 875° * 5°C. The solid solubility of iron in PbTe was found to be 0.3 at. pct by electronmicroProbe analysis. No solubility of PbTe was detected in iron. Slight deviations from true pseudobinary behavior were found to occur in the range of - 5 to 10 at. pct Fe. In the course of a general investigation of reactions of various metals with lead and tin telluride,&apos; the lead telluride-iron system was reinvestigated. It had been established much earlier than iron does not chemically react with lead telluride but forms a eutectic with a melting point of 879" The eutectic composition or other related information has never been reported, but for a number of years iron has been in general use for contacting of lead telluride and lead telluride alloys for thermoelectric applications. It seems therefore desirable to clarify the exact constitution of the system to furnish a base for the long-term evaluation of bonds made between lead telluride and iron either by pressure contacting or by brazing methods. I) EXPERIMENTAL METHODS Lead telluride-iron alloys were prepared in 10-g charges, using premelted lead telluride. This material was prepared from high-purity, semiconductor-grade lead and tellurium obtained from the American Smelting and Refining Co. and described as 99.999 pct pure. The iron used was "Armco" iron; the major impurities found here were 0.02 pct C, 0.018 pct Si, and 0.015 pct Cr. All remaining impurities were less than 0.01, the total of all impurities not exceeding 0.15 pct. Charges were prepared in closed quartz arnpoules which were evacuated and in some cases backfilled with high-purity argon to retard excessive lead telluride evaporation and deposition in slightly cooler parts of the ampoule. For high iron concentrations, this can lead to total separation of the constituents, since the vapor pressure and the sublimation rate of PbTe are quite high.4 Nevertheless, since the ampoules are closed, no change in overall composition was expected and the nominal composition of all alloys was assumed to be retained. X-ray diffraction analysis, thermal analysis, and microsections were used in the evaluation of the alloys. The nature of the system was such that X-ray diffraction was not particularly helpful. It merely served to establish that at all concentrations PbTe and a! iron were in equilibrium at room temperature. Thermal analysis was carried out by taking direct temperature vs time curves on a Sargent recorder where a width of 10 in. was kept as 1 or 0.5 mv by use of an automatic bucking voltage network. Quartz ampoules with minimized dead space, coated with boron nitride and fitted with a thermocouple reentrant, were used as containers for the charge. At high temperatures and over long periods of time, boron nitride reacts with iron. For the thermal analysis runs, however, this was not significant. More significant was the fact that the vapor pressure of PbTe at some of the meas -uring temperatures apparently exceeded I atrn quite considerably. This, in some cases, caused the slightly softened quartz tubes to blow out if great care was not taken to contain them and minimize time and temperatures used. As containers pure nickel tubes were used which also served to avoid temperature gradients in the quartz ampoule. Nevertheless, the experimental difficulties at high temperatures were severe and the monotectic temperature could therefore not be determined accurately. In general, the accuracy reached by the thermal analysis setup in this case is *4"C as determined with gold, silver, and tin, under the conditions of analysis here. Inherently, the apparatus is capable of reaching accuracies better than i 1°C. Also, difficulties were encountered in microsection-ing. They were related to polishing, since it is rather difficult to avoid pulling the iron out of the weak and brittle lead telluride matrix. It proved best to follow a procedure where, after grinding to 600 grit on carborundum paper, a polish with 6 p diamond was used on nylon cloth. Finally, #3 "Buehler" alumina and an automatic polisher were used for -5 min only, to avoid relief. The best etching results were achieved with

Jan 1, 1969

By D. E. Spiller

Introduction Precious metals recovery from ore can generally be accomplished using gravity concentration, flotation, and/or hydrometallurgical (leaching) techniques. The objective of this paper is to show why gravity concentration can be an important part of recovery systems that employ leaching as the primary unit operation. A brief discussion of modem gravity concentration equipment is also presented. Discussion Gravity concentration of ores has generated increasing interest in recent years. Reasons for this interest include: • Gravity concentration is environmentally attractive. There is little or no use of reagents. Hence, it is relatively nonpolluting. • The cost of cyanide has continued to increase. Therefore, cost savings may be realized whenever leaching feed tonnage can be reduced by preconcentration. • Compared to flotation and leaching, gravity equipment costs are low per processed ton. Field installation costs for gravity circuits usually are less because many&apos; units are supplied as self-contained modules. Also, the cost required to supply services, particularly power, to a gravity plant site are also less. In situations where preconcentration at coarse particle size is applicable, significant grinding equipment savings may be possible. • Gravity circuit operating costs are also relatively low compared to typical flotation and leaching circuits. Reagents, power, maintenance, and manpower savings in a well-engineered gravity plant may be realized. Again, if grinding is reduced, significant power and steel (media and liners) savings are possible. •In recent years, more efficient gravity concentrating devices have been developed. Benefits to Precious Metal Leaching Gravity beneficiation can complement precious metal leaching in two ways. First, the recovery of coarse liberated values before leaching may reduce leach time requirements and may reduce reagent consumption. Second, gravity preconcentration can reduce the size of a leach plant by decreasing the quantity of material to be leached. Coarse gold and silver have been shown to leach rather slowly. Kameda (1949) and Habashi (1967) have investigated the kinetics of cyanide leaching systems. They concur that in a heterogeneous reaction, the rate of gold and silver dissolution is directly proportional to the surface area. Thus, the instantaneous rate of dissolution for spherical 0.37 mm (400 mesh) gold is theoretically -25 times faster than for the same amount of gold at .841 mm (20 mesh), based on data from Fuerstenau, Chander, and Abouzeid (1979). Conversely, coarse liberated, +.841 mm (20 mesh), gold is more readily recovered by gravity concentration than is fine, -.037 mm (400 mesh) gold. Therefore, it is apparent that the two recovery systems complement one another. Figure 1 data demonstrates the potential synergism. A sample of - 3.327 mm (6 mesh) Nevada gold-bearing ore was cyanide leached using conventional bottle-roll test procedures. Gold extraction was determined as a function of leaching time. A second sample split from the same leach feed material was hand jigged to remove a coarse heavy mineral fraction, including virtually all of the +.210 mm (65 mesh) liberated free gold. This second sample, with the coarse gold and heavy minerals removed, was subjected to an identical cyanide leach procedure. Figure 1 presents the resulting comparative extraction data. Note that the percent gold extraction for the sample containing no +.210 mm (65 mesh) free gold includes the coarse gold recovered by gravity. The data show that the sample containing coarse gold required about 72 hours of leaching time to achieve 80% extraction. This compared to about 22 hours of leaching time for 80% gold recovery from the sample that contained only -.210 mm (65 mesh) free gold. Thus, there was a 69% reduction in leaching time. The improved extraction data is not wholly attributable to coarse gold removal, but rather it was the combination of gold removal and rejection of other heavy mineral cyanide consumers or leach retardants. Further investigation was not warranted at this time. Preconcentration is the second manner in which leaching systems can benefit from gravity concentration. The premise is that preconcentration can reduce the quantity of leach feed, which, in turn, may reduce leaching costs. Figure 2 presents preliminary data developed by CSMRI for US Minerals Exploration (USMX). Centennial Exploration Inc., in agreement with USMX, is proceeding with evaluations to determine the suitability of various processing schemes for recovery of gold values from the Montana Tunnels property. The data shows how the ore can be preconcentrated by gravity techniques to result in a reduced feed tonnage to secondary extraction techniques, presumably flotation or cyanide leaching. Testing has shown that Reichert cones, followed by treating the cone concentrate on spirals, can deliver about 88% gold recovery in about 13% weight, that is, 87% weight rejection. Consequently, fine grinding and reagent costs are attributable to only 13% of the plant feed rate. Cost data is not yet available, but the potential exists for significant cost savings.

Jan 1, 1985

By B. B. L. Seth, H. U. Ross

A generalized rate equation for the reduction of iron oxide was derived from which two particular equations were obtained: one for rate controlled by the transportation of gas, the other for rate controlled by the phase-boundary reaction. Pellets of pure ferric oxide having diameters of 8.5 to 17.5 mm and a density of 4.8 g per cm3 were prepared and reduced by hydrogen at 750° to 900°C. From the analysis of data obtairzed, it was observed that neither the phase-houndarv reaction nor the transportation of gas controlled entirely the rate of redziction. Rather, the mechanism of reduction can he divided into three stages. In the beginning, the process seems to depend predominantly on the surJrce reaction, hut after a layer of iron is formed the diffusion of gas becomes the controlling factor. Towards the end, however, the rate falls sharply due to a decrease in porosity. The times predicted by the generalized equation for a certain degree of reduction showed an excellent agreement with those obtained experinmentally for pellets of varying sizes. WIDE interest in iron oxide reduction has resulted in many valuable studies pertaining to thermody-namical properties, equilibrium diagrams, and chemical kinetics. Although the thermodynamical properties and equilibrium diagrams are now known with a fair degree of accuracy, the mechanism and rate-controlling step in the reduction of iron oxides presents a problem to research workers which is still unsolved. This is because the field of chemical kinetics is so highly complex. Besides the chemical reaction between oxide and reducing gas, several other processes are occurring simultaneously such as solid-state diffusion of iron through intermediate oxides (FeO and Fe3O4), the diffusion of reducing gas inwards and of product gas outwards, and the sintering of iron if reduction is carried out above the sintering temperature of iron. Furthermore, there is a large number of variables, including the nature and flow rate of the reducing gas, the chemical composition and physical properties of the ore, the temperature of reaction, particle size, and so forth, all of which can affect both the mechanism and the kinetics of reduction. Despite the controversy and diversity of opinion about the mechanism of iron oxide reduction, three main schools of thought have emerged. According to the first, the rate is controlled by the diffusion of gas through the boundary layer of stagnant gas; the second claims that the rate is proportional to the area of the metal-oxide interface, while the third believes the transportation of reducing gas from the main stream to the metal-oxide interface and of product gas from the metal-oxide interface to the main stream to be the rate-controlling step. 1) The boundary-layer theory is true mainly for packed beds where the flow of gas through the bed is important. For a single particle, the boundary layer may be prevented from being the rate-controlling step if a gas flow rate of reducing gas above the critical flow rate is used. 2) Several workers have reported a linear advance of the Fe/FeO interface which provides excellent support for the belief that reduction is controlled by the surface area. McKewanl has given formal shape to this concept with mathematical derivation and has shown it to be valid for reduction of several iron ores, hematite, and magnetite, both by H2 and H2, H2O, N2 mixtures. Some other investigators, however, do not find this theory to be entirely valid. Deviations have been observed2 and further confirmedS3 Hansen4 also agrees that deviations do occur, at least in the latter stages of reduction, while from the data of several investigators summarized by Themelis and Gauvin,5 it is clear that the theory is not always applicable and further that, when it is applicable, it does not hold in the final stages of reduction. 3) Among those who claim the transportation of gas to be the rate-controlling step are Udy and Lorig,6 Bogdandy and Janke,7 and Kawasaki el a1.8 The validity of the theory has also been acknowledged indirectly by other research workers who show that the sintering and recrystallization of iron cause a decrease in reduction rate, for it is only if the transportation of gas is important that this sintering has any bearing. However, the theory has been rejected by some because they have failed to obtain

Jan 1, 1965

By M. J. Marcinkowski, A. S. Sastri

A detailed compressive stress-strain analysis and transmission electron microscopy investigation has been made of the deformation behavior occurring in a 50 at. pct Ni-Ti (hypoeutectoid) alloy and a 54.5 at. pct Ni-Ti (hypereutectoid) alloy. In the case of the hypoeutectoid alloy, three stages of work hardening are observed. Stage I occurs at a very low stress and is associated with plastic deformation via martensite formation. Stage 11 is characterized by very rapid work hardening and is due to difficulties in causing further deformation in the fine martensite aggregate produced in Stage I. Stage III which occurs at very high stress levels is characterized by smaller work hardening rates and is due to the plastic deformation arising from alternate reconversions of the original martensites to martensites of varying orientation. Rapid quenching of the hypereutectoid alloy leads to very high yield strengths and is related to a fine precipitate dispersion that such treatment brings about. The present investigation represents the final phase of a three-part study directed toward an understanding of the solid-state transformations in near equi-atomic Ni-Ti alloys as well as the deformation mechanisms associated with these alloys. In the first part,"2 to be henceforth referred to as I, it was found that alternate simple shears on {112} planes and in (111) directions convert the parent B2 structure in the equiatomic NiTi alloy into two distinct close-packed monoclinic martensites. All of the marten-sites were of this type, whether they were formed by cooling or by plastic deformation, whether induced to form in bulk samples or in thin foils, or whether examined in the electron microscope at room temperature or below. On the other hand, in the second part of this investigation,3 to be reffered to as 11, it was shown that upon slow cooling to about 640°C. alloys in the neighborhood of NiTi which possess the B2 structure transform eutectoidally into their equilibrium phases Ti2Ni and TiNi3. However, preceding the formation of these equilibrium phases a series of metastable intermediate phases are formed. This paper will set as its goal the elucidation of the remarkable deformation behavior exhibited by NiTi. In particular, Buehler and Wiley4 have found equiatomic NiTi to be surprisingly soft, while Buehler et al.5 have shown this alloy to possess a memory effect: i.e., upon bending at room temperature it will revert to its original shape when heated to above about 50°C. In I it was shown that NiTi was soft in the sense that the yield stress was low; nevertheless, the alloy work-hardened at an extremely rapid rate to very high stress levels. On the other hand, the hypereutectoid alloys with somewhat higher nickel, say 54.5 at. pct (60 wt pct) have enormously increased yield strengths compared to those of the equiatomic alloys. In order to determine the atomistic processes giving rise to the above behavior, it was decided to examine samples that were wafered from bulk specimens deformed in compression to various strains using the techniques of transmission electron microscopy. EXPERIMENTAL TECHNIQUE All of the alloys used in the present investigation contained either 50 at. pct Ni (55.06 wt pct) or 54.5 at. pct Ni (60 wt pct) and were arc-melted in the form of a finger using the same techniques described in I and II. The finger was capsulated in a stainless-steel jacket and swaged at 850°C into rods. Compression specimens 0.300 in, long and 0.200 in. in diam were machined from these rods. In order to completely re-crystallize the samples and remove residual stresses, all of them were capsulated in evacuated quartz, annealed for 1/2 at 1050°C. and then furnace-cooled. Compression tests were carried out in an Instron tensile testing machine covering a range of temperatures from —196° to 200°C using procedures described previously.6&apos;7 In all cases crosshead speed was 0.02 in. per min. Wafers 0.015 in. thick were spark-cut from the cylindrical samples at 45 deg to the compression axes after they had been deformed to the desired strain. These specimens were then spark-planed to about 0.005 in. and then electrochemically thinned for examination by transmission electron microscopy as described in I.

Jan 1, 1969