Search Documents

By John M. Tinsley, Calvin D. Saunders, H. K. van Poollen

In the past few years much con-sideration has been given to the evaluation of the effect of hydraulic fracturing on the productivity of wells. Generally, these studies included the evaluation of fracturing materials, fracture extension and formation damage due to the use of various fracturing fluids. Only little consideration has been given to the characteristics, and in particular the flow capacity, of the fracture itself and its effect on well productivity. This paper presents the results of laboratory investigations pointed toward fie evaluation of the efficiency of various fracrures with special emphasis on the flow capacity of these fractures. Data presented in this paper are the results of both an electrical model study and physical testing. Under consideration are (I) effect of overflush, (2) premature production of well after treatment, (3) "tailing-in" with coarse sand near the end of the treatment, (4) effect of propping agent size and concentration, (5) reduction in effective frac-ture permeability caused by formation caused by formation fines, silt and clays, and (6) effect of various fluids on formation strength and competency. The results of this investigation indicate that the flow capacity of a fracture is affected by any or all of the various parameters mentioned above. The authors believe that a better understanding arid utilization of these factors should result in more efficient formation fracturing. INTRODUCTION Hydraulic fracturing has become almost a standard practice of many companies for stimulating production from old and new wells. Although most companies utilize this service, techniques of application vary widely between companies and areas. Probably too often when a well in an area responds favorably to a particular technique all future wells in the same area are treated in a similar manner. Possibly a modification of the technique would result in a further production increase. Variables, of which many are extremely difficult to evaluate from field results, hamper the selection of procedure changes. Attempts are being made by a number of organizations to analyze statistically treating techniques from production data. This is a very worthy and necessary approach but very possibly laboratory investigations may aid in evaluating some of the variables which tend to affect the results of a fracturing treatment. Some of the factors cannot be studied from practical field experience and only laboratory tests can show the possibilities which might exist. One of the factors which appears to be of major concern today is the flow capacity of the created fracture and how it can be changed. Papers on this general subject have been primarily concerned with the size of propping agent and the extent of fracture. Papers have also been written on the possible permeability damage to formations by fracturing fluids. In addition, it might be possible that another type of flow restriction is prevalent. This would be a restriction of flow through a sand-packed frac- ture caused by foreign materials integrating within the propping agent. This paper presents preliminary data obtained in an attempt to evaluate the effect of some factors affecting flow through sand-packed fractures. No attempt is being made to offer a fracturing technique adaptable to all areas and conditions, but to furnish data tending to show the possible effects which might be caused by variations in procedures and materials. PROPPING AGENT PERMEABLLITIES A hydraulically induced fracture containing sand as a propping agent may theoretically be classified as a packed-sand system. The flow of fluids through such packed systems has been the subject of much research. Although there have been numerous methods proposed for the evaluation of such systems, most writers agree on the general properties affecting their flow capacity or permeability. These properties include porosity, particle size, sphericity and the roughness of the particle. In some methods of evaluation . the particle size and sphericity terms are combined to produce an equation which is a function of the surface area of the particles. In this study the permeability of various fracturing sands was both measured and calculated. The apparatus for the permeability measurements consisted of a 52-in. Lucite tube with a 2.5-in. ID. A screen and drain plug were fitted in the bottom of this tube to retain and hold the sand in place while allowing fluid flow. Two pressure taps consisting of thin, highly perforated

By K. Tangri, M. Chaturvedi

On water-quenching from within the (a + ß) phase region Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys can undergo w transfirmation. This transformation has been attributed to the enrichment of ß Zr phase, at the solution-treatment temperature, by the solute atoms. The ß—w transformation is accompanied by a hardening 01 the alloys and in the optimum condition w-bearing specimens of the ternary alloy are about 14 pct harder than those bearing only a' phase. On aging crl reverls thermally to more stable phases, which results in a considerable softening of the specirnens, as follows: w quenched -waged + ß Zr (enriched) waged - a + ß Nb The high-temperature bcc ß Zr in certain zirconium alloys can transform to a metastable w phase which has a primitive hexagonal structure. In the Zr-Nb alloy system w phase has been observed in the composition range of 7 to 15 wt pct Nb by a number of investigators.'-' In this composition range w can form by water-quenching ß Zr or by aging. known as athermal and thermal w, respectively. Hatt and Roberts' have found that thermal w has a constant c/a ratio of 0.622 +0.002 regardless of the composition and tha: the lattice parameters are of the order of a = 5.02A and c = 3.0 ?. The actual lattice parameters depend upon composition and the temperature of aging. The lattice constants of athermal w. however, depend upon alloy composition.3 The presence of w phase in zirconium alloys can cause substantial strengthening which has been attributed as probably due to the coherency between w and parent ß Zr phase. Robinson et al.' found that the presence of w can raise the strength of Zr-5.0 Nb-2.0 Sn and Zr-5.0 Mo-2.0 Sn alloys to about 170.000 psi: however. the ductility is considerably reduced. With the growing use of Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys in the nuclear reactors, and the significant effect of w transformation on the mechanical properties of zirconium alloys studies were undertaken to study the w transformation in Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys. This paper is concerned with the formation and reversion of w phase in these alloys. 1) MATERIALS AND EXPERIMENTAL TECHNIQUES The following two alloys were studied: 1) Zr-2.5 Nb-0.5 Cu (referred to as the ternary alloy): 2) Zr-2.5 Nb (referred to as the binary alloy). The chemical analysis of the alloys is given in Table I. The alloys, in the form of 3/8-in.-diam rods and 1/8-in.-thick sheets, were supplied by the Chalk River Nuclear Laboratories of the A.E.C.L. Initial fabrication for preparation of various specimens was carried out by cold rolling and swaging with intermediate anneals at 1000°C. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-% m of Hg. For optical metallography and hardness measurements disc specimens + in. diam by + in. thick were used. After the required heat treatments the specimens were mechanically and then chemically polished in a 45 pct HNO3, 45 pct H20. and 10 pct HF solution. The hardness measurements on the chemically polished specimens were carried out on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative hardness value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using copper K-a radiations in 114.6-mm-diam camera. Thin films for transmission electron microscopy were prepared by electropolishing heat-treated a by 7 by 0.005-in.-thick strips using a modified Bollmann-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol electropolishing bath was kepl at -5OCC and polishing was done at 5 to 10 v. The thinned specimens were washed in ethyl alcohol at -30" to -40°C and dried between filter papers. The thin films

Jan 1, 1970

By R. J. Charles

SEARCH for a consistent theory to explain the relationship between energy input and size reduction in a comminution process has accumulated, over the years, an enormous amount of plant and laboratory data. Although some correlation of these data has been possible for purposes of engineering design and for the advancement of research in fracture, there is still great need of a means of predicting behaviour of a solid when it is reduced in size by mechanical forces. The best known hypotheses proposed to describe the energy-size reduction relationships in crushing and grinding stem from a common origin. The present article analyzes problems of comminution in the light of the precepts of this origin. Its object is to reconcile points of difference between these well known hypotheses and to present relationships more widely applicable to comminution studies. Theoretical Considerations: Most existing relationships between energy and size reduction of a brittle solid stem from a single, simple, empirical proposition.&apos; Although this proposition can be demonstrated by observation and experiment, no theoretical derivation is yet possible. Mathematically, the proposition may be stated as follows: dE = -Cdx/xn [1] where dE = infinitesimal energy change, C = a constant, dx = infinitesimal size change, x = object size, and n = a constant. Eq. 1 states that the energy required to make a small change in the size of an object is proportional to the size change and inversely proportional to the object size to some power n. No stipulations are placed on the exponent n in either magnitude or sign. In 1867 Rittinger2 postulated that the energy required for size reduction of a solid would be proportional to the new surface area created during the size reduction. As far as can be determined there is as yet no physical basis for Rittinger&apos;s hypothesis. Rittinger&apos;s hypothesis can be stated mathematically as follows: E, = K(oa-a-0 . [2] Er = energy input per unit volume, K = a constant, <ti = initial specific surface, and o2 = final specific surface. In the size reduction of particles of size x, to particles of another smaller size, x2, Eq. 2 becomes the well known relation: ET = K&apos; {l/x2-l/xx) [3] where K&apos; is a constant. Eq. 3 may be arrived at from the proposition given in Eq. 1 by integrating and by assigning a value of 2 to the exponent n. J dE = J - C dx/x2 E = Kt (1x - 1x) where K&apos; = C. In 1885 Kick3 proposed the theory that equivalent amounts of energy should result in equivalent geometrical changes in the sizes of the pieces of a solid. For example, if one unit of energy reduced a number of equal-sized particles to particles of one half the size, then the same amount of energy applied to the particles resulting from the first test should result again in a size reduction of one half or a final size one quarter the original size. The Kick concept may be expressed as follows: Ek = K" log x1/x2 [41 K" = a constant and E, = energy per unit volume. The expression for Kick&apos;s law may be arrived at by again integrating Eq. 1 and in this case assigning a value of 1 to the exponent n. dE= J - C dx/x Eh = - C In {x/x2) = K" log (x,/x,) where K" = 2.3 C. Application of Kick&apos;s and Rittinger&apos;s laws to comminution has met with varied success. Gross and Zimmerley4 and Piret5 have shown that Rittinger&apos;s equation applies under certain conditions of experimentation. Walker and Shaw6 express the belief that in metal turning and shaping and in grinding of both metals and minerals the production of very fine particles (less than lP) follows Kick&apos;s hypothesis, whereas Rittinger&apos;s concept is valid for the size reduction of coarse particles. For the practical case of crushing and grinding, however, neither of the above hypotheses has received general acceptance. Bond&apos; has lately proposed that since neither Kick&apos;s nor Rittinger&apos;s hypotheses seem correct for plant design work, an energy-size reduction relationship somewhere between the two would be more applicable. The fundamental statement of Bond&apos;s work

Jan 1, 1958

By C. B. Sclar and

A graphical solution is presented for the equation v =v &-cU where vb is the volume of liquid b of density 6 that must be added to liquid a of volume va and density d, in order to obtain a heavy-liquid solution of preferred density dm for mineral fractionation. The equation is valid only for pairs of liquids whose volumes are additive, but empirical density-composi-tion data show that this condition is met over wide compositional ranges by all of the heavy solutions that are commonly used for mineralogical analysis. The chart is a nomograph which consists of two horizontal volume scales ad a vertical density scale arranged so that one volume scale occurs on each side of the density scale. All the scales are linear. For two liquids of density d, and &, respectively, each volume scale has an independent level on the density scale, ad the graphical solution for vb on the nomograph is obtained by construction of one straight line. The chart can be prepared easily to cover any density range with any desired accuracy by proper selection of the scales. Heavy-liquid separation of particulate samples is an indispensable analytical procedure in the mineralogical and mineral-process ing laboratory. Heavy liquids may be used 1) to isolate specific minerals in the form of high purity products or to fractionate samples into several products with density limits for petrographic, chemical, spectrographic, and X-ray diffraction analysis,&apos;-&apos; 2) to determine the density of minerals,&apos;-l4 3) to facilitate the recognition and identification of optically similar associated minerals,15 and 4) to determine quantitatively the degree of liberation of ore minerals in ores and mill products at various limiting sizes." The preparation and recovery of heavy liquids suitable for mineralogical analysis are discussed fully in the literature and operational procedures and special equipment for heavy-liquid separation are described in numerous references.&apos;747837&apos; 13,18,25-42 Useful tabulations of heavy liquids for mineralogical analysis are given by Tickell, Mil-ner,&apos; Twenhofel and Tyler,&apos; and Lange and a very complete up-to-date list of minerals arranged according to increasing density is given by Mursky and Thompson. USEFULNESS OF THE DENSITY CHART For any particulate sample, the limiting densities selected for its fractionation by means of heavy- liquid separation depend on the respective densities of the constituent minerals and the specific objectives of the separation. In many instances, the densities of readily available and practicable heavy liquids do not coincide with those that are required, and suitable liquids of the proper density are obtained by dilution with miscible liquids. In the general case, one may wish to mix either a pure liquid (A) or a solution of two miscible liquids (AP,,) of known density with either a pure liquid (B) or a different solution of the two miscible liquids (A,B,) of higher or lower density in order to obtain a final liquid of the preferred density. In conventional practice, the latter is reached empirically by trial-and-error addition of increments of one liquid to the other. The density of the final solution may be determined either by accurately weighing a known volume of the final liquid,&apos;&apos; 532;4;40, or by means of I)a Westphal balance, 2)a hydrometer, a refractometer in the case of binary liquid systems for which density-refractive index data are available,15 4) natural or synthetic .indicators of known density, a pycno-meter. Like all trial-and-error methods, these procedures are time consuming and many require special equipment which may not be available, The purpose of this paper is to show that the volume of a liquid of known density which is to be added to another liquid of known volume and density in order to obtain a solution with an intermediate preferred density may be determined rapidly and accurately by a graphical method provided that the two liquids form ideal or quasi-ideal solutions whose volumes are additive. Empirical data47&apos;8~&apos;8~4B&apos;49 show that solutions prepared from pairs of miscible

Jan 1, 1961

By R. G. Ward, A. E. El-Mehairy

A technique was developed to calculate the density of liquid metals from the profile of a weighed levitated drop obtained by emitted light photography and calibration. The density of liquid copper was determined over the temperature range 1370" to 2100°K and expressed with the equation: The molar volumes and thermal coefficients of expansion are calculated. Copper, upon melting, was found to expand 3.34 pct. A knowledge of the density of liquid metals is essential as it is a parameter appearing in most theories of the liquid state. The liquid density is also necessary for the calculation of the commercially important contraction occurring on solidification. Unfortunately good density values are rarely available and the present work was undertaken to establish a new method of density determination free from the limitations of the existing methods. For liquid metals with high melting points, the variation and the limited number of density values reported in the literature have been caused primarily by difficulties in technique, a matter which has been adequately discussed by Urbain.&apos; In all the methods used for measuring the density of the high-melting liquid metals there are sources of error, and corrections have to be made. For example, in the method of balanced columns, the formation of gas bubbles in one or both arms was a great source of error. In the pyknometer3 and immersed-sinker methods, corrections of certain volumes for thermal expansion to the operating temperature exceed 4 pct. In the maximum-bubble method5 a correction for the thermal expansion of the bubble-tube is used (about 1.6 pct); a second correction takes into account the change in the volume of liquid displaced by the bubble-tube (about 3.5 pct). Another method used is based on the shape of a drop of liquid, at rest on an inert refractory plaque, obtained photographically or radiographi-cally. The volume is calculated from the shape, which is sensitive to the surface tension and supporting material, by some intricate empirical relation. The drop contour changes with 90 deg rotation of the support.7 The application of all methods is limited by reaction between liquid metal and the apparatus. The successful stabilization of a mass of liquid metal during levitation melting8 afforded a technique for measuring the density of liquid metals out of contact with solid materials. The technique was developed by using copper as the density of liquid copper has already been studied extensively, thus allowing comparison with the new method. It consists of calculating the volume from the dimensioned profile of the levitated drop obtained by emitted-light photography and careful calibration. The molten egg-shaped drop spins around the magnetic axis of the coil (lined vertically) at a speed which seems to increase with increasing temperature. The method does not involve corrections and the experimental setup allows the use of vacuum or special atmospheres. The maximum operating temperature is limited by excessive evaporation of metal from the droplet. EXPERIMENTAL Levitating System. A stabilizing ring was used in conjunction with a 3-turn levitating coil energized by a 450-kc per sec, 10-kw Toccotron with a high current-low voltage output stabilized to f 1 pet.&apos; APyrex glass tube with a Pyrex Optical flat window inserted through the coil and ring allowed the use of special atmospheres during levitation melting, as shown in Fig. 1. Optical System. Fig. 1 shows the optical arrangement used to photograph the profiles of the drop, parallel and perpendicular to the vertical spinning axis, simultaneously on the same frame of a high-speed 35-mm film. The optical system was adjusted to avoid any distortion of the profiles and to ensure that both profiles are in focus. The length of path from object to objective was about 30 cm, and a magnification factor close to 1 was obtained with the single-lens reflex-camera system. Temperature Measurement and Control. In operation, the specimen temperature was constant to 5 C for a fixed power input to the levitating coil and fixed rate of gas flow through the tube. The temperature was measured by an automatic two-color pyrometer (Coloratio) checked at the melting

Jan 1, 1963

By C. G. Dunn, P. K. Koh

THE primary recrystallization texture in cold-rolled silicon iron, which is the matrix texture for developing the Goss texture or the cube-on-edge texture by secondary recrystallization at temperatures near 900°C,1-5,21 has not been adequately described. Thus from the present available information, it is not possible to explain satisfactorily both the grain-growth selectivity of the matrix and the often observed magnetic torque curve, which itself provides some information on the texture. Also lacking is information on the special annealing texture that develops in this material when the annealing temperature is 1200°C or higher and the rate of rise to temperature is extremely rapid. From the work of May and Turnbull5 and from unpublished work, it was known that isothermal annealing near 1200°C tends to reduce the extent of secondary recrystallization and that a much weaker cube-on-edge texture results if appreciable normal grain growth replaces secondary recrystallization. Koh and Dunn6,7 have obtained additional information on complex primary recrystallization textures from further studies made after normal grain growth. In these instances the initial textures were retained during normal grain growth. A similar result reasonably could be expected in the present study except for the presence of a grain growth ihibitor1-5,8,9.21 and its tendency to allow only a few grains to grow. However, any information on the orientations of grains in the special annealing texture, even if far from representative of the initial matrix texture, would provide useful information on the nature of the matrix texture. In the present texture study the method of Newkirk and Bruce,10 which is based on the methods of Geisler" and Schwartz, 12 is used to obtain a complete (110) pole figure of the primary recrystallization texture. The high-temperature annealing texture is determined simply from the orientations of a large number of selected grains. The kinetic nature of the process that produces the annealing texture is treated elsewhere13 and it is shown that a form of secondary recrystallization with a very high rate of nucleation occurs during rapid annealing at high temperatures. EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon iron strip (3.16 wt pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Me-tallographic studies indicated complete recrystallization. Short-time anneals at 900° C and at higher temperatures proved that secondary recrystallization had not begun at 800°C, in fact, the short additional anneals were still in the induction period of secondary recrystallization. A rapid rise to an annealing temperature of 1260°C (2300°F) was obtained in a BaC12and NaCl fused salt bath. The structures that resulted from anneals in the range 12- to 1000-sec duration were relatively finegrained, even though the growth was a form of exaggerated grain growth13 or secondary recrystallization with a high nucleation frequency.= Many of the grains were large enough for an X-ray study using a 5-mil X-ray beam. A transmission Laue Camera and an optical-mechanical stage for moving the grains into the X-ray beam were used. A total of 325 grains were X-rayed in this manner and the grain orientations determined. Complete (110) pole figures were obtained for the primary recrystallization texture using CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and Bruce.10 The low voltage serves to reduce the spurious white radiation to a minimum. A filter of 0.001-inch iron foil was located in front of the detector slit for transmission and in front of the beam slit for back reflection. A new and improved specimen holder extended the useful tilting angle range for transmission to 70 deg instead of 60 deg as previously reported.&apos; A torque magnetometer was used to obtain the magnetic torque curves for a number of l-in. diam disk specimens. RESULTS The (110) pole figure of the material after recrystallization at 800°C is shown in Fig. 1. The positions of the pole concentrations are found to be

Jan 1, 1961

By Carl F. Lutz, Robert F. Mehl

A layer of brass was formed on 0 brass using a vapor-solid reaction technique. The variation in composition with distance within the phase layer and across the a -ß interface was determined by an electron probe. The diffusivities were calculated as a function of concentration; the diffusion coefficient in brass was found to change by a factor of twenty-five over a compositional range of 8 at. pct. An explanation is proposed to account for the large change in the diffusivity, based on possible stresses in the diffusion zone; it is suggested that the concentration dependence of the thermodynamic factor might decrease the activation energy with increasing zinc content. ALTHOUGH the body of data on diffusion coefficients (D- values) in terminal solid solutions and in isomorphous systems is quite large, there is but little quantitative information for intermediate alloy phases. This paper recounts measurements of D-values for the ? phase in the Cu-Zn system. The experimental method employed consists in the forming of alloy layers and determining and analyzing the concentration-distance (c-x) curve. The experimental method employed could have been applied to several systems; the Cu-Zn system was chosen because the D-values in the a and ß phases are well known, and can thus be used for purposes of comparison. The rates of growth, of intermediate alloy layers are known for a number of systems. In nearly all cases the thickness varies parabolically with time, as to be expected if the rate of growth is controlled by the D-values. In a few cases, nonparabolic behavior has been noted.1 Nonparabolic growth may be the result of a) a variation of the composition at the phase interface with time, b) interface-controlled kinetics, c) short diffusion times coupled with long vacancy lifetimes (in vacancy diffusion),2 and d) crystal reorientation during diffusion in anisotropic systems.3 In the Al-Ni system4 and in the Al-u5 system parabolic growth kinetics are slowly approached after an initial transient period. In general those phases stable at a given temperature in a system A-B appear as separate phase layers when A and B are put in contact and given a diffusion he at-treatment. In most cases the compositions at the interface of adjacent phase layers are those read from the phase diagrams for the termini of the respective phases. This discontinuity in concentration is taken as independent of time, and the growth of one phase at the expense of another is assumed to be independent of interface kinetics, i.e., the rate of interface movement is controlled by volume diffusion in the phases concerned. wagner6 has given many solutions for multi-phase diffusion processes, assuming that the chemical diffusion coefficient, D, is independent of concentration, as have others. Jost7 has pointed out that the familiar Boltzmann-Matano solution is as valid for a (c-x) curve exhibiting concentration discontinuities at phase boundaries as for the usual single-phase case. Heumann and associates8,9 have applied this solution to the multi-phase case, but lacking concentration data within the several layers were forced to assume linear concentration gradients, thus calculating only average D-values. The purposes of the present study were: 1) to determine the dependence of D on concentration, 2) to calculate the intrinsic diffusion coefficients D?Cu and D?Zn, 3) to establish the time-law for the movement of the interface, 4) to determine the concentration limits at the ß-? interface, and, 5) to attempt to clarify the mechanism of diffusion. EXPERIMENTAL PROCEDURE The ? phase is exceedingly brittle; conventional solid couples and conventional sectioning methods were thus inapplicable. Vapor-solid couples were accordingly employed. Unfortunately the equilibrium vapor pressures of Zn for the ? phase are unknown; to escape this awkwardness, samples were enclosed in a capsule containing powder of an alloy of known composition, sufficiently large in quantity as to be effectively an infinite source, maintaining the concentration of Zn at the sample surface constant with time. The sources of Zn-vapor which can be employed in reaction with Cu, or a brass, or ß brass, to form a layer of ? brass satisfactorily wide in concentration range, are alloys of the phases ?, or ? + E or ? + d (depending on the temperature).

Jan 1, 1962

By E. M. Kalar, I. Iwasaki, J. D. Zetterstrom

Several methods of removing fatty acid coatings from iron ore flotation concentrates were tested both on a Mesabi oxidized iron ore and on a magnetic taconite concentrate, and their effects on the duplex flotation process and on pelletizing were compared. Either acid or alkali alone could not remove the coatings, but a combination of such reagents as lime and quebracho, calcium chloride and pyrophosphate, or sulfuric acid and an organic acid (oxalic, malonic, or citric acid) was quite effective. The use of activated carbon was found to be particularly promising. The removal of fatty acid coatings from iron ores is of much practical interest when a pelletizing process is being considered for a concentrate floated with a fatty acid collector or when a duplex flotation process is being considered for upgrading an oxidized iron ore. A duplex flotation process is a fatty acid flotation of iron minerals followed by an amine flotation of the siliceous gangue from the rougher iron concentrate. Such a process is being used in the Florida phosphate fields.&apos; Although in northern Michigan mills fatty acid flotation concentrates have been pelletized successfully, at other locations fatty acid coatings on iron flotation concentrates have proved so undesirable in the agglomeration operation that other methods of concentration had to be sought.&apos; Since fatty acid coatings cannot be removed as readily with a simple acid or alkali treatment from iron oxide surfaces as from Florida phosphates, a combination of reagents, such as lime and quebracho,3 lime and alkali phosphate,4 or sulfuric acid and oxalic acid,&apos; has been proposed. It was also thought that activated carbon might be effective in removing fatty acid coatings due to its high adsorptive capacity. Activated carbon, with its enormous surface per unit of volume, is well known for its exceptional efficiency in removing organic pollutants from industrial effluents. This article presents the practical aspects of the above methods when they are applied to the duplex flotation process and to the pelletizing of iron flotation concentrates. The article also includes a preliminary investigation of the common parameters involved in the depressant activity of the reagents. EXPERIMENTAL WORK Initially, the experimental work was directed towards the optimization of each method for the removal of hydrophobic coatings from iron oxide surfaces floated with fatty acids. Subsequently, the methods thus optimized were tested in the duplex flotation process with an oxidized iron ore and in the pelletizing process with a magnetic taconite concentrate. Preliminary Flotation Tests: Although the three types of chemical treatment reported in the literature were briefly investigated for the purpose of comparison, major emphasis was placed during the preliminary flotation tests on the use of activated carbon because it was thought to have certain advantages over the chemical methods. LIME AND QUEBRACHO - To obtain a flotation concentrate for optimizing the lime and quebracho method of fatty acid removal, the magnetic taconite concentrate was used. The concentrate had a size consist of 90% passing 325 mesh and analyzed 64.5% iron. After a few preliminary tests the fatty acid flotation procedure with the magnetic taconite concentrate was standardized as follows. A 1200-g sample of the magnetic concentrate was pulped in a Fagergren laboratoy flotation cell to 40% solids, conditioned with 0.5 lb of soda ash per ton for 2 min, and then further conditioned with 1.0 lb of Acintol FA-2 per ton for 2 min. After 5 min of flotation, recovery was nearly complete, averaging 98.6% of the weight and 98.7% of the iron. The cell product, which amounted to 1.4% by weight and analyzed 63.2% iron, consisted mainly of relatively coarse middling particles. Since the repro-ducibility of the flotation concentrates produced by this procedure was vey high, the same procedure was used to prepare fatty acid concentrates for each of the six tests of the lime and quebracho method. To test the removal of the fatty acid from the magnetite surfaces by the lime and quebracho method, a fatty acid froth product was returned to the flotation cell, repulped by 30 sec of agitation, and then con-

Jan 1, 1968

By F. C. Pittman, D. W. Harriman, J. C. St. John

This paper mentions briefly the history of hydraulic jetting as applied to perforating and fracture initiation. It points out the advantages of hydraulic perforation and undercutting as an aid for creating a fracture at the point desired rather than depending upon the weakest point in the formation for breakdown. It describes early experimental work with jet nozzles in search of better nozzle materials. The effect of splash-back damage and its subsequent influence on jet body and tool design during this work is discussed. A series of cutting-rate curves for jets cutting steel and steel-cement-formation combinations is presented to show the effect of hydrostatic head and the point of diminishing returns with respect to cutting time. There is a series of photographs showing various types of rock formation in which perforation and undercutting tests were made. These stones were drilled and the casing cemented in place as in an actual well. The casing was perforated and circularly cut as if preparing for a fracturing job. The conclusion reached in the paper is that hydraulic jetting with sand-laden fluid can be used for perforating and undercutting casing, cement and formation rock for the intended purpose of inducing the formation to fracture at a desired point. INTRODUCTION Hydraulic jetting as a means of cleaning a formation during acidizing has been used for many years. The acid-jet gun was used to clean formation and for drilling cement from casing with acid. This tool was dropped to a seating ring installed on the tubing and could be retrieved by reverse circulation or wire line. In this process, the fluids were directed against the formation to clean and penetrate beyond the mud-damaged area. After the development of the hydraulic fracturing process, interest in jetting the formation with abrasive-laden fluid was renewed. The cutting action of abrasive fluid on pumping equipment, which is a well known problem, has been utilized to perforate and undercut casing, tubing and formation. In this process, surface areas are provided in the formation on which the frac- turing pressures may work to produce a fracture at the location desired. EQUIPMENT The tools used consist of bodies containing two, three or four jets in a single horizontal plane equally spaced around the circumference. The body is threaded to the end of a string of tubing and run into the well. In addition, an expendable tool is available that may be left in the hole after perforating and produced through until necessary to remove the tubing. The bottom of each tool is equipped with a ball-type back-pressure valve. The ball can be reversed to the surface and recovered. This allows reverse circulation so that loose sand which accumulated below the tool while jetting may be removed before the fracturing job. The present jetting tools are of such length that, when screwed together, the jets fall on 12-in. spacing. ANALYSIS OF THE PROBLEM Early work with nozzles indicated that hardened steel was not a suitable material for jets and that more durable material would be required. Ceramics were tried and found to be superior to steel but still too shortlived for most applications. Tungsten carbide, which was tried and found to be the best material available, is now being used for jet nozzles. Analysis of the problems presented by this process indicated that the following information was needed. 1. The effect of submergence on a jet stream and the effect of submergence on the cutting rate of a jet stream. 2. The cutting rate and depth of a jet stream in steel. 3. The cutting rate in various formations and point of diminishing returns. 4. Size of hole or slot cut in a pipe by a given jet. 5. Fluids and sands used. 6. The flow of various weight fluids through the jet nozzle and the discharge coefficients. 7. The type cut formed in the formation by the jet stream. 8. The stretch and contraction of tubing due to temperature and pressure. The cutting effect of a jet stream on a target in the atmosphere is rapid and spectacular as most of the

By H. L. Sauder, J. L. Newman, C. Waddell

An instrument capable of measuring subsurface flow rates is described. The instrument is self-contained and may be run on piano wire line. It detects flow by means of an impeller suspended between two torsion wires. The force of the well fluid striking the impeller causes the impeller to rotate, exerting a torsional force to the wires. This force is determined by recording the angle of rotation of the impeller on film using a battery-driven, clock-controlled camera. The impeller is sensitive to flow in either direction and the same instrument can be used to measure injection as well as production rates. Changes in direction of flow, such as might be caused by thief zones, are measurable and are indicated by a reversal of the direction of rotation of the impeller. Adjustment of the sensitivity of the instrument to measure a wide range of flow rates is accomplished by the use of different size torsion wires. An umbrella-type fluid trap, which contacts the casing or wellbore, diverts the flow through the flow tube. The fluid trap remains closed while rurrning in the hole and can be opened at any point in the well. The instrument with the trap closed is 1 3/4 in. OD and may be run through 2 in. tubing. Successful flow profiles have been made on wells with flow rates ranging from 60 BID to 4,000 B/D at surface pressure up to 4,500 psi. The instrument is designed for high-pressure and high-temperature operations. INTRODUCTION The need for an instrument that will measure flow rates in a wellbore is as old as reservoir engineering itself. A number of such devices have been designed within the past few years. Some of these have been described in the literature1,2,3,4,5,6 One of these devices1. a hot-wire anemometer type, made many successful jobs in dry gas producing areas. Difficulty was encountered when this flowmeter was used in wells producing liquids and development work was initiated to overcome this difficulty. The present flowmeter is the result of this work and provides an instrument with a wider range of application in the industry. Consider- able development work has been done on the tool involving many changes in the mechanics of recording the flow readings, however, the basic principle of flow detection has remained the same since its inception. PRINCIPLE OF OPERATION The basic principle of operation of the flowmeter is the utilization of a portion of the kinetic energy of flowing well fluid to impart a rotational force to an impeller suspended between two torsion wires. This impeller, Fig. 1, is a screw-type propeller with the blades having a pitch angle of 40. As the well fluid passes through the instrument it strikes the impeller. The resulting force rotates the impeller and twist\ the torsion wires to a balance point at which the torque imparted to the wires balances the force required for the impeller to deflect the well fluid. The impeller is symmetrical and a change in direction of the flow results in a reversal of the direction in which the impeller is deflected. Thus the direction of the flow as well as its velocity is indicated. A dial is attached to the impeller by means of a hollow tube through which the upper torsion wire extends. The angular position of the impeller is recorded by photographing the dial at frequent intervals. In any given set of torsion wires the modulus of shear and polar moment of inertia remain constant and the deflection varies directly with the applied torque. The deflection imparted to the torsion wires also varies as the square of the fluid velocity. Further, the velocities represented by any two given deflections hear the following relationships: and Where V = velocity of flow stream and O ;= deflection. This is the basic relationship which is used to calculate the relative velocities represented by a given set of deflections where the velocity represented by any one of the deflection readings is a known quantity. For a given torque, the deflection of the torsion wire varies inversely as the fourth power of the wire diameter. Wire sizes ranging from ,005 in. in diameter to .022 in. in diameter can be used. The range of

Jan 1, 1957

By Richard R. Zupp, David A. Stevenson

An experimental method to determine the carbon activity in various solid solutions was developed. Samples of the solid solutions and an Fe-C reference sample were equilibrated with respect to carbon content by annealing them in a Hz-CHI gas mixture in a closed cell. The carbon content of each sample was determined, and the carbon activity was obtained from the carbon content of&apos; the reference sample and well-established data for the dependence of the carbon activity on the carbon content in Fe-C alloys. The influence of vanadium on the activity of carbon in austenitic Fe-C-V alloys at 1000°C was determined by this technique. A general semiempirical correlation was developed to describe the dependence of the activity coefficient of- carbon on the composition of ternary austenitic iron-base alloys containing interstitial carbon and a substitutional solute. The correlation is particularly useful in predicting the partitioning of- carbon between various alloys. THE influence of substitutional solutes on the activity of interstitial solutes in metallic solid solutions is important in the theory of alloy phases. Solid solutions of particular interest are the fcc austenite phases of ternary Fe-C-Z systems, in which carbon is the interstitial solute and Z represents any substitutional solute. Carbon-activity data are also needed in these solid solutions to solve practical problems; the quantitative treatment of diffusion-controlled transformations&apos; is an examvle. Experimental information is available for ternary austenitic solid solutions containing Mn,2 Si,2 and A16 as the substitutional solute. Because qualitative preliminary studies indicated that vanadium appreciably decreases the carbon activity,14 the present investigation was undertaken to determine the influence of vanadium on the activity of carbon in austenite. Although Flender and ever" measured carbon activity over a range of compositions in the Fe-C-V system, they were primarily interested in determining phase boundaries in the ternary system, so most of their measurements were outside the composition range for stability of single-phase austenite. Petrova and Shvartsman&apos; also made limited measurements of the carbon activity in Fe-C-V alloys. The dependence of the carbon activity on the carbon content of an alloy may be determined by passing COCOz or H2-CH4 gas mixtures of carefully measured composition over the alloys, determining their equilibrium carbon content, and utilizing the relevant equilibrium relationships. smith16 used this technique with both CO-COZ and HZ-CH4 gas mixtures to determine the dependence of carbon activity on carbon content in pure Fe-C alloys. His data, which are in good agreement with those of some previous and subsequent investigators,6&apos;17 but not with those of others,lfl&apos;ao are usually considered to be the most reliable. Although the same method can be applied to Fe-C-Z alloys, it is difficult experimentally, because the appropriate gas mixtures are almost pure CO or Hz. A simpler technique is to simultaneously equilibrate the Fe-C-Z alloys and pure Fe-C alloys with the gas mixtures, and then use Smith&apos;s data to determine the carbon activity in the pure Fe-C alloy. A number of investigators have employed this technique. others Have used the partitioning of carbon at the interface of a diffusion couple prepared from an Fe-C alloy and a Fe-C-Z alloy. In the present study, a closed-cell method was developed by which carbon was selectively transferred via a gas medium between pure Fe-C alloys and Fe-C-V alloys which were not in physical contact. A similar method was developed independently by Heckler and winchel14 and used to study the Fe-C-Ni system. EXPERIMENTAL METHOD A schematic diagram of the experimental arrangement is shown in Fig. 1. In a typical experiment, a 5-g Fe-C sample was placed in one compartment of a quartz cell, and a 5-g Fe-V sample was placed in each of the other compartments. The cell was evacuated, outgassed, backfilled with approximately 125 Torr of hydrogen, and sealed. After being placed in a fur-

Jan 1, 1967

By S. Shapiro, J. A. Ford

The crystallo graphy of several grains of the lamellar Ni-Ni3 B eutectic solidified under conditions appvoachirt equilibriun has been examined.. A preferred interlace relationship has been observed in this system which may be described as: A detailed study of this interface by means of an atomistic model reveals the interface Plane to be puckered and more accurately describable as: Analysis of the atomic configuration on these planes reveals that this interface conforms to the orientation criteria proposed for directionally solidified lanzellar eutectics. In addition, a model is proposed to help explain the growth of a "puckered" interface. DURING the past several years an increasing number of unidirectional solidification experiments on eutectic alloys have been reported in the literature. The primary emphasis, in most cases, has been the effect of growth variables on microstructure. Some authors have, however, studied the crystallographic orientations and interfacial relationships resulting from these experiments. Four crystallographic studies have been published;&apos;-4 in each of these there is a factor which tends to prohibit the extension of the observations beyond the particular system. In the Al-CuA12 system, the approximately equal volume fractions of the phases have resulted in sorrie controversy as to which phase constitutes the matrix. In the Mg-Mg,Sn eutectic the presence of several interconnecting lamellar systems2 complicates the analysis. The two remaining eutectics. 1nSb-b and Al-Ali, are both rodlike (the latter exhibits a plate morphology at low solidification rates): the matrix in each of these alloys is the simpler (fcc) phase. Studies of nucleation in eutectic alloys indicate that the more complex constituent is the nucleating -.phase.&apos; For the purpose of an analysis of interface crystallography it was deemed desirable to study a lamellar system in which the matrix was the more complex and, presumably. the nucleating phase. Recently it has been shown that there is a eutectic in the Ni-B system between Ni3B and i; preliminary investigation by the authors indicated that the matrix in this eutectic is the boride phase. The structure of Ni,B is reported to be orthorhombic, the compound being isostructural with cementite. This eutectic is therefore analogous to that between austenite and cementite. Furthermore, the Ni-B system is not susceptible to a competing eutectic reaction as occurs in the Fe-C alloys; nor does it exhibit a eutectoid decomposition. For these reasons the study of the interfacial relationship in the Ni-Ni3B eutectic was undertaken. PROCEDURE Ingots of nominal composition 3.5 and 3.6 wt pct B were induction-melted in boron nitride crucibles within a graphite susceptor under a boric oxide slag; a dynamic argon atmosphere was maintained over the melt to prevent rapid oxidation of the susceptor. The raw materials used were 99.97 pct Ni from Huntington Metals Division of International Nickel Co. and 99.8+ pct B chips supplied by the United Mineral and Chemical Co. The analyses of the starting materials are listed in Table I. The melt was held at 1500cC for 2 hr to insure complete reaction and allowed to cool to room temperature. The castings were chemically analyzed for boron and were metallographically examined for uniformity. The metallographic samples were mechanically polished through 0.1 p A1,0, and etched with Carapella&apos;s reagent. Each master casting was cut up to make several specimen blanks which were remelted, in boron nitride crucibles, to form ingots of 1/2 to 3/4 in. in diarn by 7 in. long. These ingots were unidirectionally solidified using a modified vertical Bridgman technique. The rate of solidification was assumed to be equal to the uniform rate at which the crucible-susceptor assembly was withdrawn from the induction coil. This rate was varied from 1.18 to 2.21 cm per hr. In order to perform these experiments it was found necessary to redetermine the eutectic composition. This was accomplished by the zone-melting technique described by Yue and lark.&apos; An ingot of 4.5 wt pct B was zone-melted in a horizontal boron nitride boat 7-1/2 in. long with a 112-in.-square cross section. A

Jan 1, 1967

By Lyman Johnson

Single crystals qf copper in "single slip" orientatiorzs have been deformed in compression. During defortnation all of the independent deformation parameters have been measured. These parameters consist of thefive strain components and three components descrihing the lattice rotation. By a finite strain analysis these pararmeters , forrming a deformation gradient martrix, are related to the amounts of slip on each of the twelve slip systems. The results show that the amount of secondary slip is about equal to the amount of primary slip. This is an order of magnitude larger than has been believed previoutsly. ACCORDING to early theory and experiments, when a single crystal of a fcc metal is deformed in tension or compression it should deform by slip on only one slip system until the stress axis reaches a symmetrical orientation.&apos; However. the observation of a large increase in the secondary dislocation density during ..single slip" makes it clear that some slip does occur on secondary systems. Knowledge of the amount and distribution of this secondary slip is essential to a complete understanding of the mechanisms of single-crystal deformation. Ahlers and Haasen 2 and Mitchell and Thornton1 have tried to detect the amount of secondary slip in single crystals of silver and copper, respectively. Each simultaneously measured the angle A, between the tensile axis and the primary slip direction and the length 1 of a gage section of the specimen after incremental amounts of deformation in tension. The measured A, was then compared with the theoretical single slip angle hp. given by sin Ap = j sin . hO where ?o was the initial angle between the tensile axis and the primary slip direction and lo was the initial gage length. In both sets of experiments a small but systematic difference between ?e and ?p was found. This difference must be due to the occurrence of secondary slip. However, as Mitchell and Thornton1 pointed out. nothing quantitative can be said about the amount and distribution of this secondary slip from the measurements that they made. The reason that no quantitative conclusions could be made is because no unique solution for the distribution of slip on the twelve fcc slip systems can be determined from only two measured deformation parameters such as A and 1. There are, in fact, eight independent macroscopic deformation parameters that can be measured when a single crystal undergoes a homogeneous deformation. Physically these can be thought of as the five finite strain components and the three angles describing the crystal lattice rotation. All eight of these parameters were measured by Taylor4,5 for aluminum deformed in tension and compression. At that time the concern was to show that slip occurs on {111 (110) systems in fcc metals, and the mathematics were not available to determine what slip distributions were compatible with the measurements. In this paper the mathematics6,7 are developed that allow the slip distribution to be determined from these measurable macroscopic deformation parameters. The analysis is applied to the measurements of the strain and lattice rotation of copper single crystals deformed in compression. The results show that the amount of secondary slip is an order of magnitude larger than had previously been thought. CRYSTALLOGRAPHIC DESCRIPTION OF A HOMOGENEOUS DEFORMATION The deformation of a solid body can be represented by a transformation matrix F that transforms the un-deformed state into the deformed state. Consider a vector X connecting two material points in the unde-formed material and the vector x connecting the same two material points after deformation, where both vectors are referred to the same set of Cartesian axes. The final vector x is related to the initial vector X by the equation: X = FS. [2] Eq. [2] can be considered as the equation defining F, which is called the deformation gradient matrix. Its components are: If the deformation is homogeneous, the transformation is linear and the components of F are constants. Using subscript notation, if P is the unit vector in the initial direction of a material line, the components of the unit vector p in the direction of the same material line after deformation are given by:

Jan 1, 1970

By Klaus Detert

Fifteen and 18 pct Ni maraging steel and several binavy and ternary alloys of the iron-rich corner of the Fe-Co-Ni system have been studied. After annealing in the austenite range, these alloys were deformed slightly by cold rolling and subsequently aged. Compavison of experimental measurements at various processing stages indicates that small degrees of deforn~ation (5 to 10 pct reduction in thickness) do not influence hardness and strength or the aging kinetics. Electrical resistivity and ductility are somewhat redu]ced and the coercive force is substantially lower when compared to identical samples which were not deformed. The results are explained in terms of retained austenite which transforms into martensite with the small amount of deformation. RECENTLY there has been increasing interest in maraging steel for applications in electric power generators requiring a high ratio of power to weight.&apos; Fifteen pct Ni maraging steel has been investigated to evaluate its properties and performance for application as high-strength magnetic rotor steel,&apos; and a thorough investigation of the precipitation and transformation processes in this alloy has been conducted in this laboratory.3 The influence of deformation, which preceded the aging treatment, was also studied. It was found that a small deformation in the order of 5 pct has a rather striking effect in reducing the coercive force. Other interesting effects on the properties caused by such deformation have led to the more detailed studies reported herein. EXPERIMENTAL METHOD The methods used to produce the samples from 15 pct Ni maraging steel have been described elsewhere.3 The general procedure of hot forging and cold rolling to sheet has been followed. The composition is included in Table I which also contains the composition of the 18 pct Ni maraging steel grade 250 studied. More data about the material and the processing of the 18 pct Ni maraging steel have been recently reported.4 The experimental alloys of binary and ternary Fe-Ni-Co alloys were made by levitation melting in an argon atmosphere and casting into rod-shaped ingots 7 mm thick weighing 20 g. From these ingots 25-mm-long rods were machined to study the phase transformation by a dilatometer. These rods were then cold-rolled to strips, 2.4 mm thick. Annealing for austenitizing was done in tube furnaces in an argon or helium atmosphere followed by cooling in the water-cooled portion of the tube. Aging was done in a salt bath containing a neutral blend of Alkali nitrates and nitrites. Vickers hardness was measured using a load of 50 kg for 15 sec. Tensile tests were carried out on a hard beam tensile tester at a strain rate of 5 X lo-&apos; per sec using flat samples with a gage length of 37.5 mm and a cross section of 1.25 by 6.25 mm. Estimated sensitivity was 5 K x strain and 0.35 kg per sq mm stress. Magnetic saturation was determined on small cylindrical samples, 2.5 mm in length and diameter, by measuring the force exerted by the gradient of a magnetic field of 1000 oe per cm in a mean field of 11,500 oe. The measured values could be reproduced within *1 pct. Coercive force was measured by a precision-type magnetic field probe in a magnetic coil as described by Foerster.5 The magnetizing field was 1300 oe. The samples were 5 cm long, 1 cm wide, and 2.4 mm thick. he coercive force was measured to within +0.1 oe. Electrical resistivity was measured by using a potentiometer on flat strips with a gage length of 100 mm and a cross section of 2.5 by 0.5 mm. The accuracy of the measurement was 0.1 pct but the reproducibility of the measured specific resistivity among different samples was in the order of 1 pct. The method used to prepare the samples for electron transmission has been reported elsewhere.3 RESULTS Fig. 1 shows the influence of deformation after annealing on the resistivity, hardness, and coercivity. The samples were annealed for 30 min at 1000"C,

Jan 1, 1968

By G. Purcell, S. C. Sun

In an attempt to determine the relative collecting ability of 18-carbon fatty acids, studies were performed on rutile in aqueous solutions of the fatty acid soaps. The preceding article reported the electro-kinetic properties; this article outlines the flotation behavior. Results of these flotation experiments are described and correlated with the electrokinetic results. Recent studies of the electrokinetic1-4 and the electrochemical5,6 properties of a few solid-liquid interfaces have provided a better understanding of the flotation process. A number of investigators have attempted to determine the relative collecting ability of 18-carbon fatty acids, but their published results (even for the same mineral) vary widely. Such lack of agreement indicated a need for further investigation. In an effort, therefore, to resolve the problem, electro-kinetic studies were made on rutile in aqueous solutions of the fatty acid soaps. Following the determination of the electrokinetic properties, the flotation behavior of rutile was studied. Results of these flotation experiments are described in this paper and are correlated with the electrokinetic results. MATERIALS AND EXPERIMENTAL PROCEDURE Materials: Pure -28, + 35-mesh rutile crystals were used for all flotation tests, and nitrogen-saturated conductivity water was used throughout. Sodium hydroxide and hydrochloric acid were added for pH regulation. The methods of purification for these materials and the preparation of the soaps have been described elsewhere. 7 Equipment: A Hallimond cell, constructed in a manner similar to that described by Fuerstenau, Metzger and Seele,8 was used for the flotation of mineral particles; however, a coarse pyrex frit was substituted for the capillary. Procedure: Purified nitrogen was led through a two- way stopcock into a graduated cylinder partly filled with water. The gas forced water from the cylinder back into a header tank until the water level in the cylinder coincided with a predetermined mark. Reversal of the stopcock then allowed water in the tank to force nitrogen into the cell until the water in the graduated cylinder rose to a second predetermined mark. In this way a constant volume of nitrogen under practically constant pressure was used for each flotation test. However, the flotation time varied, depending upon the amount of mineral floated and the pH of the solution. Rutile crystals were transferred under water from a storage bottle by a glass scoop holding 1.7 g. Consistency of the scoop samples was good, varying from a low value of 1.67 to a high of 1.74 g. The water added to the conditioning bottle during mineral transfer was drained off, and then 2 cu cm of either hydrochloric acid or sodium hydroxide were added. The concentration of pH regulator was adjusted to give approximately the final soap solution pH that was required. The order of addition of reagents did not affect the results within the limits of experimental error. Soap solution of the required concentration was added under nitrogen pressure to fill the bottles completely. Conditioning for 1 hr was carried out on rolls rotating at 35 rpm. After conditioning, 2.5 cu cm of solution were run off into the container of a Beckman (model G) glass electrode pH meter. The electrodes were rinsed in this solution, which was then discarded, and 2.5 cu cm more were added for pH determination. The remaining solution and the mineral were transferred to the cell; care was taken to ensure that all mineral was washed out of the bottle by the conditioning solution. With the cell back in its flotation position the liquid just reached the desired level, and the test was started immediately. The amount of agitation in the cell was kept constant, and flotation was carried out without the use of a frother. In each series of ten tests one was run with no collector added to ensure that the mineral had not become contaminated, and two were conditioned at the same pH to check reproducibility. After each test the cell was dismounted, soaked in cleaning solution, washed in hot water and then rinsed with distilled water.

Jan 1, 1963

By D. R. Hay, E. Scala

STUDIES of structure-sensitive properties, especially mechanical behavior, have shown that grain and subgrain structure play an important role. The mechanical properties of tungsten, in particular, are sensitive to the nature of the intergranular structure. Substructure and dislocation networks in single-crystal and polycrystalline tungsten have been studied by Nakayama et al.&apos; Various orders of substructure were observed ranging from a microscopic first order (grain diameter: 2 to 8 mm) to a microscopic second order (grain diameter: 50 to 300 p), and, within the latter, dislocation networks forming an even smaller order of substructure. In their single crystals, grown by arc fusion, the degree of misorientation in each order was small: 16&apos;3OU, -11, and -10" for the first-, second-, and third-order substructure, respectively. To study the properties of polycrystalline tungsten, powder metallurgy tungsten is generally used. However, in a mechanical property investigation, the zone-melted or arc-fusion crystals are more desirable than the powder metallurgy product due to their higher purity and absence of porosity and other defects inherent in consolidation by powder metallurgy. Grain boundaries can also be produced in melted stock by working and recrystallizing. However, material with subgrain mis orientations of the order of several degrees (high-angle substructure) has not been reported previously and is the subject of this communication. Crystals were grown by electron-beam, floating-zone melting. The starting material, Sylvania Pure-tung welding rod, was given one zone pass at a traversal rate of -2 mm per min. Through control of the zone temperature, it was possible to influence the degree of crystal perfection. By maintaining the zone at a high degree of superheat, high-perfection crystals could be grown. However, at temperatures only slightly above the melting point, the zone-melted crystals contained a high-angle substructure. A sensitive control of the zone temperature was not possible due to the difficulty of estimating the temperature of the zone and of providing a constant supply of power to the sample. Therefore, an empirical method, using the shape of the molten zone as a criterion, was adopted as an indication of temperature. At high degrees of superheat, the surface tension of the molten zone decreases and a neck forms at the top of the zone, whereas at low zone temperatures the diameter of the zone remains reasonably uniform. Although it was not possible to obtain a continuous variation of misfit angle, the conditions could be directed toward the growth of either high- or low-angle substructure by maintaining only a slight neck in the zone (sufficient to establish that it was molten) or a well-necked zone, respectively. Mass spectrographic analyses of both types of material revealed no significant differences in the concentrations of their impurities. The degree of misorientation at high angles was obtained by measuring the angular spread of spots corresponding to a single reflection on a Laue back-reflection photograph. Fig. 1 shows a typical Laue back-reflection photograph of a crystal with a 3-deg spread. By measuring the angular deviation of the spots corresponding to a single reflection from the mean center of the spots around which constant angular deviation contours were drawn, an average angular spread of misfit could be calculated. The angular average was weighted by the number of spots observed in each angular interval. At angles greater than 5 to 6 deg the spots from different reflections begin to overlap, and cannot be associated with a particular reflection. Laue back-reflection photographs taken at different locations on samples .with approximately 3-deg spreads showed only a small difference in angular misorientation, less than 8&apos; of arc, within individual specimens. The microstructure was examined using Berg-Barrett X-ray extinction contrast microscopy. Berg-Barrett photographs taken directly on the as-grown surface, Fig. 2, show an essentially equiaxed subgrain structure of -0.1 mm in average grain diameter in both high- and low-angle crystals. Fig. 2(a) is a photograph of a sample with a low misfit angle and Fig.

Jan 1, 1968

By P. Greenfield, P. A. Beck

The phase is a hard and extremely brittle material with a tetragonal crystal structure, containing 30 atoms per unit cell&apos; It occurs in many binary and ternary alloys of the transition elements. The existence of twelve a phases has been reported in binary alloys of metals from the group vanadium, chromium, molybdenum, and tungsten with metals from the group manganese, iron, cobalt, and nickel. It is a characteristic fact that the composition of the o- phases in the various binary systems is not the same. Rather, there is a gradual shift in composition, for instance in the series of chromium a phases, approximately as follows: CrMn,, FeCr, Cr3Co,. In recent years several ideas have been put forward to account for this variability of composition. SullyZ proposed that a was a type of electron compound, characterized by 1.7 electrons per atom in excess of the number required to fill the Pauling atomic orbitals. These excess electrons were supposed to just fill the first Brillouin zone of the u structure. However, later work indicated that the phase is ferromagnetic at low temperatures, so that a- is unlikely to be a full zone compound.~ Another proposal,* which is also based on the structure of the transition elements advanced by Pauling, and in fact leads to essentially the same a compositions as Sully&apos;s theory, suggests that the u phase is characterized by a constant number of electron vacancies per atom. The electron vacancy numbers N,. used were originally the same as those in the Pauling theory, but were later modified empirically vn order to bring about better agreement with data for the p phase in certain ternary systems. For alloys, N,, was calculated on the assumption of simple additivity from the electron vacancy numbers of the components, as follows: N,. = 4.66 (Mo + Cr + V) + 3.2 (Mn) + 2.2 (Fe) + 1.71 (Co) + 1.6 (Ni). On this basis a reasonably constant value of N, = 3.4 was obtained for all of the binary u phases and a fairly constant value of N,, = 3.1 for the various p phases. More recently, Bloom and Granta pointed out that a similar correlation with the total number of 3d and 4s electrons per atom is also fairly well fulfilled and concluded that no reference need be made to the Pauling theory. This proposal does not lead to the same binary a compositions as the one described above, so that the relative merits of the two proposals may be determined on the basis of direct comparison with experimental composition data. The purpose of the present paper is to provide such a comparison. Since the experimental data for the composition ranges of several of the known u phases were rather incomplete, it was decided to carry out new experimental determinations for many of the binary systems. Experimental Procedure The alloys were prepared by induction melting in recrystallized alumina crucibles, either in vacuum or in helium atmospheres. Some aluminum was picked up from the crucibles in the alloys of high vanadium content, but this was minimized by keeping the alloys in the molten state for as short a time as possible. The maximum aluminum impurity was 0.13 wt pct by chemical analysis, in an alloy containing over 50 wt pct V. In general, the as-melted compositions agreed accurately with those obtained by chemical analysis. In the case of manganese, however, losses inevitably occurred; consequently all manganese alloys were analyzed. Specimens of all alloys were annealed at temperatures ranging from 1000" to 1300°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. All manganese alloys were sealed in quartz tubes under vacuum before annealing. The specimens were held at temperature for between four and eight days before being quenched into cold water. Alloys were prepared for microscopic examination by mechanical polishing, usually followed by electrolytic etching. X-ray diffraction specimens were prepared by crushing the homogenized alloys, and by reanneal-ing the obtained powders in evacuated quartz tubes for a few hours at the temperature of the lump anneal. X-ray diffraction patterns were made with unfiltered chromium radiation, using an asymmetrical focusing camera of high dispersion. Using microscopic and X-ray techniques jointly, the accuracy

Jan 1, 1955

By J. W. Leomrd, B. A. Donahue

Results of research are presented examining the extent to which the analytical characteristics of the relatively distinct coal bands from a variety of coal seams can be related to each other. This paper dis-cusses an approach for developing a practical coal petrographic quality control program based on conventional analyses, most of which is part of the standard A.S.T.M. procedure. The work is a final follow-up to Part I of this series which was prepared by the authors as an approach to applying conventional coal petrography to single coal seams. Recent published work by the authors entitled Petrography for Coal Mining and Coal Prepration: Part I dealt with interrelating various chemical and physical properties of coal1 measured using conventional analyses made on distinct petrographic bands taken from single coal seams. Since most coal production facilities process coal from a single coal seam or from very closely related coal seams in the same area,2 emphasis on interrelating the properties within a single seam appeared appropriate. The distinct petrographic bands were analyzed on the assumption that such differentiated data would be more representative of a heterogeneous coal seam than the single analytical value commonly used to characterize each property of an entire seam.34 Effort was directed at demonstrating the extent to which the interrelated chemical and physical properties 5,6 could be developed into nomographs or petrographic standardization graphs. Thus, one analysis, determined on a series of petrographic fractions separated from a single sample, was used to estimate numerous other properties in each fraction by referring to the previously established petrographic standardization graphs. This conventional approach to coal petrography was undertaken as a suggested feasible means by which a few coal analyses could be employed to develope a more penetrating knowledge of the properties of coal from any given seam in order to monitor more extensively its performance at the point of utilization. Such procedures can support development of the type of in- formation commonly sought through automated testing and through the use of computers.7 The broad knowledge which can be developed through these procedures is intended for application in the generation of an analytical profile or broad characterization of coal. These estimates were not intended as replacements for individual coal analytical tests. In this expanded second part of the research program, distinct petrographic bands from nine coal seams in the Central Appalachian Region were physically and chemically analyzed to elucidate the extent to which this concept of conventional petrography could be broadened for application to numerous coal seams. In presenting this second phase of work, the relationships developed are presented individually and not in a connecting series of nomographs or petrographic standardization graphs as in the previous work, thus leaving open the combinations of possibilities to individual interpretation and application. MATERIAL AND EXPERIMENTAL WORK Nine coal seams, representing a wide range of rank, from the Central Appalachian coal fields were used in this study. The distinct petrographic bands from the Kittanning, Pond Creek, Jawbone, Tiller, Poca-hontas No. 3, No. 2 Gas, Eagle, Winifrede, and Pittsburgh coal seams were separated by carefully removing a portion of each band at the face of the seam. The following were determined: ash, sulfur, free swelling index, heating value, bulk specific gravity, volatile matter, Hardgrove Grindability Index, and Gieseler Plastometer measurements. Determinations, where procedures were available, were carried out using ASTM standard procedures.8 Bulk specific gravity was determined using a kerosene volume displacement procedure modified from a method applied by Headlee and McClelland of the West Virginia Geological survey,9 Those bands with a bulk specific gravity greater than 1.60, which is generally above the practical specific gravity cleaning range of bituminous coals, were excluded and no analyses were performed. Much of the initial organization of this second phase of work was developed through the extensive use of a computerized statistical monitoring program (see Ref. 4). However, in order to achieve the closest possible interpretation of results, the final organization of data proceeded mainly from exhaustive trial

Jan 1, 1968

By W. E. Newell

The basic principles and assumptions involved in D. L. White&apos;s solution5 for ultrasonic wave amplification in piezoelectric semiconductors are summarized. If the gain per unit length is maximized at each frequency without regard to the drift-field power density, the gain increases linearly with frequency. Therefore it would seem that very high gain is possible for frequencies in the hundreds of megacycles. However, with present materials the resulting drift-field power density is so large that cooling would be a major problem. For this reason it is more realistic to judge the capabilities of an ultrasonic amplifier in terms of the gain that is possible with a specified power density. In this case the gain at high frequencies does not increase but decreases more rapidly than l/f. The calculation of the gain us frequency at a fixed power level involves the repeated solution of a cubic equation and is therefore tedious. For the purpose of comparing different materials, sufficient accuracy can be obtained from an approximate solution which may easily be plotted as three straight lines on logarithmic graph paper. This method is used to compare the Performances of CdS, CdSe, ZnO, and GaAs. At a power density of 10 watts per cu cm, the first three give maximum gains of 60 to 80 db per cm in the vicinity of 60 megacycles. At the same power density, GaAs has a maximum gain of about 7 db per cm near 150 megacycles. Although an increase in mobility usually increases the gain for a specified power density, it is shown that there is an optimum mobility above which the gain decreases. An approximate expression for the optimum mobility is established. It is well-known that the interaction between charged particles and an electromagnetic wave can be used to amplify the electromagnetic wave. In the conventional traveling-wave tube, electrons in a vacuum are caused to move at a velocity slightly greater than the wave velocity, thereby coupling energy into the wave.&apos; In principle, the same effect would be evident in a solid except that repeated collisions prevent the electrons from attaining a velocity greater than that of an electromagnetic wave. However, the drift velocity of electrons can be made to exceed the velocity of an acoustic wave in a solid. In 1956, weinreich2 noted that the deformation potential provided one means of coupling energy from drifting electrons into an acoustic wave, but the effect was too small to be of any practical importance. It was not until 1961 that White and Hutson demonstrated that the piezoelectric effect provided a strong enough coupling to give appreciable amplification of an ultrasonic wave and awakened wide interest in electron-phonon interactions. Qualitatively the effect may be described as follows. An acoustic wave propagating through a piezoelectric material is accompanied by an electric-field wave. If the vibrations are properly oriented with respect to the crystal axes of a piezoelectric semiconductor, the local electric fields are axially directed and cause bunching of the charged carriers. If the drift velocity of these carriers is less than the velocity of sound, they tend to be dragged along by the acoustic wave. This electroacoustic effect results in a net potential appearing across the material and in attenuation of the acoustic wave. On the other hand, if the drift velocity exceeds the velocity of sound, energy is coupled from the carriers to the acoustic wave and amplification results. Related effects which are being investigated include ultrasonic amplification in semimetals6-&apos; and semi-conductor, and current saturation in piezoelectric semiconductors.&apos;4-17 There are various problems which hinder the immediate application of ultrasonic amplification in a practical device. First, there are the traditional problems encountered in the design of acoustic delay lines: attenuation in the electromechanical transducers, reflected waves (which can lead to self-oscillation in an amplifying device), mechanical tolerances necessary to maintain phase coherence, and so forth. Second, there is the problem of selecting the best material from among the various piezoelectric semiconductors as they become available in single-crystal form with a wide choice of characteristics. This paper deals with the second problem and shows that the most realistic way of comparing materials is in terms of the gain which can be obtained without exceeding a

Jan 1, 1964

By J. E. Warren, J. H. Hartsock

Because of the extensive utilization of hydraulic fracturing for the stimulation of low-productivity wells, the two related problems of fracture design and evaluation have become economically significant and, as a consequence, helve motivated this investigation. The producing characteristics of horizontally fractured wells were studied to determine the fracture configuration that should be employed as the basis for the design of the treatment and to develop a method that can be used to establish the degree to which the design objectives have been achieved. The equations which describe the steady-state flow of a single-phase fluid into, and through. a finite-capacity fracture were solved numerically for an idealized reservoir-fracture model. The numerical results were used to obtain an apparent skin effect for each combination of the parameters considered. Based on the computed results, subject to the limitcitions implied by the assumptions that were made, the following general conclusions were drawn. 1. For a radius of drainage at least four times us large as the radius of the fracture, an apparent skin effect that is independent of the radius of drainage can be calculated. 2. The productivity of the hydraulically fractured system, relative to that of the unfructured well, can be determined from the apparent skin effect and can be used to establish design objectives. 3. In the evaluation of a fracture job, it is not Possible to determine both the radius of the fracture and its flow capacity uniquely from the apparent skin effect; an independent determination of one of the quantities is necessary. lNTRODUCTION Although hydraulic fracturing has been employed as a method for stimulating the productivity of literally hundreds of thousands of wells during the past 10 years, it is only in the last few years that improvements in fracture design1-6 and fracturing technique&apos; have combined to increase the probability of obtaining a successful treatment to such an extent that the mechanics of the method may be considered to be standardized. From an economic point of view, however, two related questions must be satisfactorily answered before hydraulic fracturing can be used in the most profitable manner. The two questions are the following. I. For a particular well in a given formation, what are the optimum design specifications for the fracture treatment? 2. Have the design objectives been achieved by the fracture treatment? The significance of these questions has been recoguized, and some attempts to obtain answers have been made. Howard, et al,8 endeavored to determine the optimum treatment, based on maximizing profits, for any given formation; unfortunately, this work was based on a crude method for approximating the productivity of a well. Carter and Tracy9 utilized the same approximation to study the effect of fracturing on the behavior of a well producing by virtue of a solution-gas drive. Electrolytic models were used by van Poollen10 to investigate the variation in productivity due to fracturing; however, only a limited number of results were presented. Later, from the same model results, van Poollen, et al,11 attempted to justify an approximate expression for determining the productivity of a fractured well. It is quite apparent that there is a definite lack of the practical information necessary for specifying the optimum fracture configuration to be considered for design purposes. The only detailed attempt to develop a procedure for evaluating the result of a given fracture treatment appears to be that of van Dam and Horner.12 These authors described a technique for analyzing pressure build-down data, obtained immediately after fracturing, to determine the final fracture volume, the final fracture porosity, the fracture area, the fracture thickness and the in situ fluid loss of the fracturing fluid. While this approach should be useful whenever acceptable pressure measurements are available, it does not yield a value for the flow capacity of the fracture. Since the problems of fracture design and evaluation are inversely related, it should be sufficient to study the effect of the fracture configuration on the performance of a well. The primary objective of this investigation is to evolve a technique for computing the desired solutions. The secondary objective is to analyze these computed results in order to prescribe a method for evaluating fracture treatments. Because this study is exploratory in nature, its scope