Search Documents

By R. P. Fischer

A large production of vanadium during the war helped Germany to meet her critical requirements for the ferroalloy metals. Vanadium was needed not only in the ordinary high-speed too1 steels, but in other as a substitute for chromium, nickel, and molybdenum, which were scarce. Lacking a source of vanadium ore, however, the vanadium was obtained as a by-product of the steel industry—va-nadium-bearing pig iron smelted from iron ores containing about o. I per cellt V was blown in converters to yield vanadium-rich slag, from which vanadium was recovered by chemical treatment. The production capacity obtained was said to be about 6,500,000 lb. of vanadium a Year. Although the general Processes of Preparing vanadium-rich slags as well as the recovery methods described herein are known, some of the details presented may be of interest to both the American steel industry and the vanadium producers. No adequate data on the cost of the vanadium produced in Germany are known, but it seems likely that the cost exceeds the commonly quoted domestic price of about $1.10 per pound of contained VzOa. Information on the German vanadium production was obtained by a team of geologists from the Geological Survey* United States Department of the Interior, during investigations in May and June 1945 of the German utilization of low-grade raw materials. These investigations were sponsored by the Chief of Engineers, War Department. It is a pleasure to acknowledge the aid obtained from Messrs. H. C. Smith and J. D. Dickerson, investigators assigned to the Army Ordnance section of C.I.O.S., and Mr. C. F. Park, Jr., of the Geological Survey team. The data on vanadium recovery from iron ores were obtained from the Kaiser Wilhelm Institut fiir Eisenforschung, the Hermann Goring steel plant at Watenstedt, and from notes made by other investigators at other German steel plants. Preparation of Vanadium-rich Slags Most German iron ores contain only about 0.1 per cent vanadium, or even less, but some of the scandinavian iron ores available to the German iron industry in the past contain a little more than 0.1 per cent. In general German practice of vanadium recovery, nearly all of the vanadium in the ore goes into the pig iron, which is blown in the Thomas converter, yielding a slag containing about I per cent V. This slag is remelted, the vanadium again going with the iron, which is again blown in a converter, yielding a slag that averages about 10 per cent V. This slag is treated at special chemical plants, by the process of a sodadizing roast, water leach, and acid precipitation of vanadium oxide. The Herman Goring steel plant at Watenstedt used the low-grade Salzgitter iron ores, the average composition of which is shown in Table I, column I. The acid and basic iron produced in the blast furnaces contained about 0.3 per cent V. A Thomas

Jan 1, 1948

By A. F. Bertuzzi, M. R. Tek, F. H. Poettmann

A method is presented for predicting pressure drop for two-phase fluid flow in horizontal pipes. A set of 267 experimental measurements randomly sampled from approximately 1,000 measurements from various literature sources was used. Pressure gradients calculated by the procedure developed and compared with the experimental values showed a bias of +0.82 per cent and a standard deviation of 20.8 per cent. The advantatges of this method over other available methods of predicting two-phase flow pressure drop are (a) its comparative simplicity of application, (b) its relative independence of flow patterns, (c) its accuracy, which on the basis of a statistical evaluation predicts pressure drop closer than other available methods, and, (d) its ability to satisfactorily correlate laboratory data from various sources while the correlations from these sources do not appear to agree with one another. The method has been reduced to a simplified graphical procedure, suitable for field use. A two-phase f factor is defined and correlated with parameters involving the flowing gas-liquid mass ratio, a Reynolds number for the gas phase, and a Reynolds number for the liquid phase. The choice of parameters allows the correlation to reduce to the usual f factor plot for the limiting conditions of (111 gas or all liquid. INTRODUCTION The mechanics and characteristics of two-phase flow systems have been of interest throughout the industry for some time. In numerous engineering installations such as pipe lines, chemical reactors, and heat exchangers, two-phase flow conditions are of every day occurrence. In oil production operations it has been desirable, in some cases, to consider transporting gas and oil together in a common pipe from oil field to process plant. The trend toward centrally located stock tank batteries in oil fields has resulted in longer gathering pipelines in which more than one fluid phase is flowing. The increase in the producing capacity of oil wells due to new production tech- niques has created the need for review and re-design of many surface gathering lines for properly handling the increased production. Optimum pipe size for the situations described above has become an important factor. The problem which is of interest here involves the ability to predict the relationship between pressure drop, fluid properties, fluid rates, pipe diameter, and pipe length. Although the literature1,5,10,13,18,19 contains various articles dealing with specific cases of the problem, Lock-hart and Martinelli17 proposed the most general solution. Their method has been later modified by Baker:1 Alves2 demonstrated that different flow patterns are possible for a flow mechanism defined by Martinelli such as gas turbulent, liquid turbulent. Baker explained deviations experienced with Martinelli's correlations on the basis that different flow patterns could exist for the same flow mechanism. Using Martinelli's method of correlatioil, Baker correlated data for each flow pattern for the turbulent-turbulent flow mechanism. Bergelin and Gazley6,7 presented a correlation for predicting gas phase

Jan 1, 1957

By E. J. Pasierb, H. W. Paxton

Mavkers ill a diffusion couple in the iron-chromium system move towards the high chromium side indicating Dcr > DFe at the marker composition. By a combituztion of measurements of D& and D a: a function of composition, this is also shown independently. DFe is calculated as a function of composition. and shown to be in reasonable agreement with measured values by other workers. MEASUREMENTS of marker movements in diffusion couples have been used from time to time to demonstrate that a vacancy or interstitial mechanism may be operative. Since there is a possibility that ring diffusion1 may be operative in chromium, the present experiments are of interest in showing some non-ring mechanism in iron-chromium alloys around the equiatomic composition. EXPERIMENTAL PROCEDURE The movement of markers originally at the interface between 1-in. sq sections of pure Cr (6 mm thick) and outer slabs of 30 Cr-70 Fe alloy was followed as a function of time at temperatures from 1150" to 1425"C, in a Kanthal-wound furnace. Temperature control was +5°C over extended periods. The analyses of these alloys are given in Table I. Selection of suitable markers presented a considerable experimental problem; the eventual solution was to draw quartz rod down to 0.01 cm and seat this in V-grooves 0.01 cm deep on each side of the chromium prior to welding. A preliminary experiment in which the groove was machined in the alloy gave identical results. Welding was accomplished by passing a heavy current through specimens under moderate pressure in a helium atmosphere. This method produced good welds with a planar interface as shown by subsequent metallo-graphic investigation. Any markers which did not adequately fill their groove and showed subsequent contamination from the atmosphere during heat treatment were not considered reliable. The composite sample was ground and metal-lographically polished on the four sides perpendicular to the interface. Fiducial marks (deep milled slots) were made outside the diffusion zone to check on total volume change. All necessary measurements were made on a metallograph reading to +0.0005 cm. The samples were wrapped in tantalum foil and given diffusion anneals for times to 200 hr in carefully purified dry hydrogen in a sealed McDanel porcelain tube. Chromium-zirconium chips were introduced near the specimen as an additional getter. The specimens were cooled relatively slowly after the diffusion anneal to preserve the McDanel tube but no significant error in effective time at temperature was thereby introduced. At least 1 mm was ground off the surface before measurements were taken. It was observed that the grain size following short diffusion anneals was several mm and was appreciably larger in the 30 Cr alloy than in the pure Cr. No significant grain boundary penetration was present as indicated by the etch limit. The results are presented in the next section. Measurements of D were made by standard sectioning techniques with chemical analysis. Machining difficulties limited the

Jan 1, 1961

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. M. Shigley

The record of the largest magnesium plant in the country utilizing sea water as a primary raw material stands as another victory in the struggle for large-scale production of pure chemical elements from the oceans. Bromine was the first element to be economically and commercially recovered when, in 1933, a six million pound per year unit was built on the Atlantic Coast near Wilmington, North Carolina, by the Ethyl-Dow Chemical Co.' The bromine was reacted with ethylene to produce ethylene dibromide, a necessary associate of tetraethyl lead in ethyl antiknock fluid. Within eight years that plant was doubled and redoubled, and another large unit was put into operation at Freeport, Texas, taking bromine from the Gulf of Mexico. In 1940, in fortunate anticipation of the impending demand for magnesium and the limitations of the production from natural brines, the Dow Chemical Co. turned again to the sea, and designed and erected a plant at Freeport to produce 18,000,000 lb. of magnesium per year from sea water.2 In March 1941, two months after the new plant had been put into successful operation, construction of an 18,000,000-lb. Government-financed addition was started. Late in 1941, as a part of the $400,000,000 defense program intended to produce 600,000,000 to 700,000,000 lb. of magnesium per year, Dow was asked to build and operate for the Government a 72,000- ooo-lb. plant near its original plant at Freeport. Within a few days after the Japanese made their attack at Pearl Harbor, preparation of a site was started at Velasco, Texas, for the construction of the Texas plant of the Dow Magnesium Corporation—the largest known magnesium plant utilizing sea water as its raw matcrial. Less than six months after the first piling was driven, urgently needed magnesium was in steady production. Five months later, the plant had exceeded its rated capacity. It remained above rated production until the general magnesium curtailment was applied to Government-owned plants in September 1944. Credit for the construction and operation record of the Dow magnesium plant must be divided among the efforts of a very determined group of men, an extremely favorable location, and a simple process. It is with the two latter aspects of the plant that this article will deal. The site for the new enterprise was chosen near Velasco, Texas, on property bordering the Brazos River at a point approximately 6 miles inland from the original magnesium plant and 7 miles inland from the Freeport Harbor on the Gulf of Mexico. This location was far enough away from the operating units to reduce both interference from construction and the vulnerability of closely bunched manufacturing operations to the then feared air attack. Yet the distance inland was not too great for the economical construction of a barge canal from the harbor to serve both the transportation of raw

Jan 1, 1949

By David W. Mitchell

WHILE pure magnesium does not corrode rapidly the presence of even very small quantities of certain other metals accelerates corrosion remarkably. Because magnesium is such an electropositive metal (E° = +2.34 volts)' the presence of substances that permit galvanic activity is extremely undesirable. It is stated that as little as 0.017 pct of iron in magnesium causes a marked increase in the corrosion rate.2 Magnesium and its alloys are commonly melted in iron or steel pots; consequently the commercial metal has the opportunity to pick up iron if it has that tendency. Quantitative data on the solubility of iron in magnesium are of practical as well as of academic interest. Some magnesium alloy castings tend to have large grain size unless suitable treatment is given to the liquid metal just prior to casting. One method of grain refinement consists of "superheating" the metal just prior to casting. "Superheating" is heating to a temperature 100 to 200°C above the casting temperature and holding for a short period of time. Superheated metal has a much finer grain than unsuperheated metal. A satisfactory explanation of this phenomenon has not been forthcoming. One hypothesis attributes the grain refinement in the superheated metal to precipitation of some phase that is miscible at the temperature of superheat but not miscible just below the casting temperature and which is thought to provide nucleating centers for crystallization. This phase, if the foregoing hypothesis is correct, would probably be a metal or an intermetallic compound. Of the metals likely to be found in magnesium alloys, iron is one of the most likely candidates for the role of grain refiner for iron occurs in small quantities in all commercial magnesium and magnesium alloys. A. Beck' states that magnesium, in either the liquid or the solid state, cannot dissolve iron and that iron exists as a finely divided suspension which does not settle out because of its extreme fineness. Beck also presents a micrograph showing a large iron dendrite in magnesium but does not comment on the crystallization of iron from a solution supposed to contain none. It is doubtful that dendrite formation from suspended iron would be possible. This suspension theory is the basis of patents4 covering the removal of iron from magnesium by allowing the iron particles to act as nuclei for the formation of primary magnesium crystals which can be separated by segregation. Also covered by patents is the removal of iron by the addition of another metal to form an intermetallic compound with the iron which, because of its increased particle size, is able to settle out of the molten metal. Here, too, quantitative information on the extent of iron solubility in liquid magnesium is of more than theoretical interest. M. Hansen,5 in his critical collection of the data on binary alloys, states that iron is not soluble in liquid magnesium. W. R. D. Jones6 who studied the physical properties of low iron magnesium alloys observed a

Jan 1, 1948

By G. A. Koehler

The Hiawatha mine, a producer of iron ore, is near the City of Iron River, in Iron County, Michigan. This mine, operated by The M. A. Hanna Co., has been chosen by the author as a typical iron mine in this district that is using the cut-and-fill mining system. General Geology The Hiawatha ore body lies along the steeply dipping north limb of a syncline that closes around on the east end to form a bathtub-shaped structure. Throughout this major structure there are very many smaller wrinkles or folds, which vary the direction as well as the thickness of the ore body. The total length of the ore formation with minor interruptions so far developed is about 3600 ft. The ore body throughout the entire present depth of 2000 ft. has averaged approximately 40 ft. in thickness; it is somewhat narrower at the upper levels and shows a marked increase in thickness on the bottom levels. This increase in thickness probably indicates that the bottom of the trough is near or that a major monoclinal fold has been encountered, which flattens the ore and gives apparent horizontal thickening. The footwall of this ore body is generally a black, graphitic slate, very rich in iron sulphides, quite combustible when exposed to air, and very treacherous to handle during mining operations. The hanging wall, in most places, is a cherty, fairly hard iron formation, and in general stands quite well ill open stopes. There are places, however, where black slate is found in both the hanging wall and the footwall, which makes mining difficult, as the black slate tends to slough off after being exposed to air. In these places it becomes necessary to leave a scale of ore 5 to 6 ft. thick on both hanging wall and footwall, which is not recovered. Fig. I shows a typical vertical cross section through the Hiawatha ore body. Type of Stoping Because of the size and shape of the ore body and the hard, dense structure of the ore, sublevel stoping has been an efficient and economical method of extracting the ore. This method, with various minor changes, has been used since the mine was opened in 1893. There have never been any stope-filling operations, however, until recent years, when crushing of pillars and black-slate fires forced the issue and methods were arrived at to fill all stopes. Development of Deeper Levels Shaft sinking to deeper levels in development operations has been done successfully by two methods without interference or hindrance to production. These systems are: I. Sinking an auxiliary winze a short distance from the shaft, then drifting back to the shaft location and putting up a pilot raise through to the bottom of the shaft. This raise is always in the manway compartment of the shaft, so that no work is ever done under a cage or skip. A 20-ft.

Jan 1, 1946

By W. T. Isbell

IN the Parkes process of lead refining, after desilverization has been completed by means of the addition of zinc, there remains in the lead from 0.5 to 0.6 pct zinc. At this stage in the refining operations virtually all impurities are reduced to refined lead specifications except zinc and antimony. All excess copper, nickel and cobalt have been removed by the zinc additions. The silver remaining should not exceed 0.1 oz per ton. It then remains only to remove the zinc and antimony in order to produce refined lead. At the Herculaneum plant of the St. Joseph Lead Co., practice formerly was to complete the refining by means of oxidation in a reverberatory furnace. This process consisted of heating the lead to 14000 to 1500°F and allowing it to come in contact with excess air passing over the surface of the lead and periodically agitating the bath of lead with air. This procedure not only resulted in the loss of zinc but of a considerable quantity of lead converted to the oxide in the form of dross and fume. The fume, collected in the baghouse, together with the dross was returned to the blast furnace, thus adding appreciably to the circulating load on the blast furnace and refinery. In addition, operation and maintenance of the reverberatory furnace was expensive and required the performance of disagreeably hot and somewhat hazardous work. The process of dezincing with high vacuum was developed at this plant as a substitute for the oxidation process and finally led to lower operating costs, the practical elimination of dross and fume and the direct production of metallic zinc, which is very suitable for re-use in the desilverization process. Essentially this process consists of subjecting the lead to high vacuum, in a kettle provided with means for heating, a bell-shaped member open at the lower end so constructed that it can be immersed in the molten lead, and means for evacuating the interior of the bell and for sealing an agitator. Metallic zinc is thus produced and collects on the upper cooled part of the bell member. This metallic zinc is periodically removed and re-used in the desilverization process. The process is quite simple. It is conducted at a low temperature, thus permitting the use of iron equipment, and shows a material saving in refining costs over the old method. EQUIPMENT AND ITS USES Dezincing Machine.-The equipment employed in this process consists of a dezincing machine, a steel kettle of 120 tons capacity, a vacuum system and equipment for handling the dezincing machine (Fig I). The dezincing machine consists of a compact assembly, suitable for handling with an overhead crane, consisting of a treating chamber and the agitating mechanism. Treating Chamber.-The treating cham¬ber is a bell-shaped shell (4), similar in shape to a hemispherical kettle with a lid

Jan 1, 1947

By Karl J. Benecke

Though the first patent on a bucket wheel excavator (BWE) was granted in 1881 in the US, this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generation, despite the low heating value of German lignite on the order of 8500 kJ/kg (3600 Btu/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is on the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output mines. The largest one, Fortuna mine in the Cologne district, produced a total of 45 million tons of lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95.2 million bank m3 equal to 200 million tons of overburden had to be removed to accomplish this lignite output. The largest BWE ever built is working in the Fortuna mine [(Fig. 1)]. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 tons and its wheel diameter 21.6 m, as high as a seven-story building. Major reasons for the development of BWE technology in Germany were: ? Lignite deposits with moderately consolidated, alluvial-type overburden (gravel, sand, loam, marl, clay, etc.) ? Great overall depth of the deposits, ranging far beyond 100 m, requiring a wide opening of the mine, hence not permitting direct overcasting of overburden. ? Multiple-seam deposits of poor-quality coal divided by reject partings, which demand a perfectly selective digging tool for clean separation. In general, these conditions are almost identical to those prevailing in the lignite deposits of Texas and neighbouring states: The type of overburden suitable for BWE digging, the overall deposit depth ranges down to around 100 m, and finally, the multi-seam occurrence with partings between seams, the latter ranging from just 1 m to a few meters in thickness. Technique As the Texas-type lignite deposits come into focus more and more as a possible fuel source in power plants to replace natural gas and crude oil, the following will deal with the BWE technology for mining a typical Texas lignite deposit under the aspect of producing enough fuel for a 500-MW power plant located at the mine mouth.

Jan 1, 1980

By W. C. Ellis, E. S. Greiner

WHEN metallic materials are deformed plastically, the process may be considered as one in which hardening and recovery occur simultaneously. The net hardening is that produced by deformation in the absence of recovery lessened by recovery during and immediately following deformation. Strain hardening takes place through movements of large groups of atoms acting to a degree as an entity. A complex microstress system is developed. Recovery is a diffusive-type process involving single atoms or, at most, only a few atoms in concerted action. This is accompanied by elastic strain relaxation. Recovery is strongly temperature-dependent. The driving energy for the process resides in thermal fluctuations of the atoms augmented by the energy of the stress field producing the deformation, and by that produced by the deformation. At very low temperatures recovery is essentially absent, or very small. At high temperatures in the hot working range, recovery is so rapid that deformation results in no appreciable net hardening. The interplay of strain-hardening and recovery results in differing end structures depending on the temperature and the strain rate of the process. For example, there is a prominent difference in the spacing of the slip markings and in the detail of X-ray diffraction patterns. High temperatures and slow strain rates favor a wide spacing of slip markings and sharp reflections.',' This suggests that change in rate of the recovery concurrent with deformation modifies to a degree the manner of the deformation. Different slip systems may operate. For very slow rates, the mechanism may, as has been suggested, differ from that of "classical slip." In the experimental work that follows the findings will be interpreted from the point of view developed in this section. Recovery and Electrical Conductivity Electrical conductivity is a sensitive indicator of the state of strain in a material3' * and was used in this investigation. The materials studied in wire form were: OFHC copper, a high purity (99.99 pct) and 2s grade aluminum, and grade A nickel. Wire annealed and initially 0.050 in. in diam was drawn through diamond dies in a simple holder maintained at 25", —75°, or — 195°C. Precautions were taken that for each material all conditions of drawing were the same except the temperature. Electrical resistivity was measured for each condition at 20°C. This was done as soon as practical after drawing to minimize possible room temperature recovery. The data for the four materials are plotted in Fig. 1 in terms of the change in resistivity for drawing at the several temperatures. The effect of temperature of drawing on the increase in resistivity is most pronounced for copper. Drawing at 25°C to 80 pct reduction in area increases the resistivity approximately 2 pct; drawing at —195°C to the same reduction increases the resistivity about 6 pct. The increase in resistivity" & in this metal is due to extra scattering of conduction electrons originating in the lack of orderly arrangement of the atoms induced by the deformation process. It has been suggested

Jan 1, 1953

By C. W. Spencer, F. G. Hochgraf, R. F. Cheney

Columnar grained specimens of nickel, containing 0.25 pct Si and 0.22 pct Mn, have been exposed to liquid bismuth in the temperature range 670° to 1050°C. Under isothermal conditions the liquid penetration rate is constant. The activation energy for the process is 22,000 cal per g-atom. Small amounts of plastic deformation, introduced into specimens prior to exposure, increase the penetration rate. The slou. step in liquid film penetration is associated with a reaction which occurs at or near the leading edge of the film. Either transfer of nickel across the liquid-solid inteqace or diffusion in the grain boundary ahead of the liquid film is suggested. Aliquid metal, if brought into contact with the surface of an unstrained solid metal, will usually penetrate to some extent into the grain boundaries of the solid. Under isothermal conditions the extent of penetration after any particular time of exposure is related to the relative magnitudes of the interfacial tensions concerned.1,2 If the liquid-solid interfacial tension is less than one-half the grain boundary tension the liquid may penetrate at a relatively rapid rate for an indefinite distance into the grain boundary surfaces. If the liquid-solid interfacial tension is greater than one-half the grain boundary energy, liquid penetration occurs at a continually decreasing rate so that after the liquid has penetrated to a relatively short distance below the surface the process essentially ceases.3 Many observations of a qualitative nature concerning inter crystalline attack by liquid metals have been reported, for example, liquid bismuth upon copper,' liquid mercury upon brass,4 and liquid mercury upon nickel.' Scheil and Schessl determined the rate of penetration of liquid bismuth into the grain boundaries of hot rolled copper rod? At constant temperature, penetration rate was found to be independent of the depth penetrated, the rate in- creasing with increasing temperature corresponding to an activation energy of 20,000 cal per g-atom for the process. It was suggested that at lower temperatures the liquid travelled mainly along lines of three grain intersections while at temperatures greater than 1000°C essentially all grain boundary surfaces were covered. Recently, in a study of copper bicrystals having a common [loo] axis it was found that at 649°C bismuth penetrated 22, 25, and 63 deg boundaries while it did not penetrate 2, 12, 15, and 72 deg boundaries.' Elbaum reported that liquid gallium penetrates aluminum grain boundaries to a depth of 0.6 cm after 11 hr at 27°c.8 Assuming that the rate controlling step in the process was diffusion down the liquid film to the specimen surface, a diffusion coefficient of 10-5 cm2 per sec was calculated. This paper reports a study of the penetration of bismuth-nickel liquids into the grain boundaries of a nickel alloy, containing 0.25 pct Si and 0.22 pct Mn as principal alloying elements. The phase diagram

Jan 1, 1962

By J. E. Ostberg, G. Phragmen, A. Hultgren, S. Wohlfahrt

Detailed study was made of a number of rimming ingots, both low and high carbon, and especially upon effects of superimposed air pressure. Requirement to suppress core bubbles is between 10 and 15 atm; at 6.5 atm freezing was in semikilled manner and at 3 atm, steel was of rising type. Probable mechanism of freezing under various conditions is discussed. AN earlier paper' reported an investigation made by a committee for studying rimming steel ingots appointed by Jernkontorets in Stockholm. The present paper is the outcome of some further work done by the same committee. Since the characteristics of ordinary rimming steel are connected closely .with the amount of gas liberated during freezing and since this amount of gas is governed by the pressure, it was considered of interest to ascertain in what manner and to what extent definite pressures applied to the top of the liquid steel in the mold would affect the solidification process and the consequent structure of a rimming steel of ordinary composition. The experiments were made at the Domnarfvets Steel Works. The steel was made according to normal practice in a 4-ton Rennerfelt electric furnace. Ferromanganese was added in the furnace; no aluminum was added, with one exception. Analyses of the four heats are given in Table I. The top-poured ingots measured about 12 in. sq x 48 in. and weighed about 1300 lb. One or two ingots of each heat were allowed to solidify under pressure, using a special device for admitting compressed air to the upper closed part of the mold, as shown in Fig. 1. A heavy plate sealed with asbestos was bolted to the top of the mold. The plate had a tapered aperture for pouring. Immediately after pouring the hole was closed by a wedged plug, and compressed air was admitted through a hole in the plug. Because of some delay in applying the plug, full pressure was not reached immediately. The pressure was adjusted to the desired value as indicated by a manometer. In order that the interior of the ingot might have the benefit of the pressure, the freezing of the top crust was delayed by a refractory lining applied to the top part of the mold, Fig. 1. Ingots were also cast from each heat without applied pressure, and with and without refractory lining at the top. Axial sections of ingots were cut either of the whole ingot or of some part of it of special interest; sections were polished and usually etched.' To facilitate description of structures the following terms may be used for different types of ingots solidified under gas evolution: 1. Box-hat or boot-leg ingot: Abundant gas evolution during casting and during rimming; no rim holes. 2. Normal rimming ingot: Lively gas evolution during rimming; usually rim holes in lowest part of

Jan 1, 1952

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By G. W. Imholz

The effect of new discoveries and development of other pools recently discovered is reflected in the increase in production from 586,000 bbl. during 1940 to 758,000 bbl. during 1941 in Coleman County. The States Oil Company's No. I Hudson, Coleman County, was the discovery well of the Silver field, with a total depth of 3540 ft.; initial production, 10,000,000 cu. ft. of dry gas and 60 bbl. of oil per day from the Gray sand, topped at 3482 ft. The first well drilled in the new Jim Ned field was the Merry Bros. and Perini No. I Greer, also in Coleman County. It had a total depth of 3937 ft. and an initial production of 152 bbl. of 42" gravity oil in 6 hr., through I-in. choke, from Gray sand encountered from 3909 to 3937 feet. J. E. Farrell's No. I Rose, Haskell County, was a new discovery, around which no additional wells have been drilled. Total depth was 3002 ft., plugged back to 2780 ft. to test an oil sand encountered from 2663 to 2685 ft., which when perforated with 76 shots at that depth was good for 85 bbl. of 40" gravity oil. In Fisher County, General Crude drilled its No. 12 Flanagan to a total depth of 6746 ft. After plugging back to 4578 ft. to test a sand encountered from 4515 to 4528 ft. it was abandoned as a dry hole. The top of the Ellenburger was reported as 6094 feet. Interest in Jones County continued unabated, largely through the development of the Wimberly pool in the southern part of the county, where five Cisco sands are producing. At present the pool has been defined on the south and the southwest. The structure has 170 ft. of closure; the lower limestone pays producing on top of the structure and the fist pay encountered, the Akard sand, producing on the flanks of the structure. Five deep wells were drilled in Stonewall County (H. and T.C. survey)—the Shell Oil Company's No. I-A Patterson, in block D, with a total depth of 6827 ft., dry and abandoned; the Shell Oil Company's No. I Rutherford, block I, with a total depth of 6239 ft., dry and abandoned; the Leader Oil Company's No. I Bilberry, block D, with a total depth of 5700 ft., dry and abandoned; Forest Development Company's No. 2 Boyd, block D, with a total depth of 4753 ft., dry and abandoned; and the Hunter et al. No. I Boyd, block D, total depth 4757 ft., dry and abandoned. J. E. Farrell drilled his No. I Tipton south of a well that produced from a Strawn sand for some time, to a total depth of 5202 ft., where it was abandoned. The well is in the southwest corner of sec. 43, block 19, T. and P. survey, Nolan County.

Jan 1, 1942

By G. W. Imholz

The effect of new discoveries and development of other pools recently discovered is reflected in the increase in production from 586,000 bbl. during 1940 to 758,000 bbl. during 1941 in Coleman County. The States Oil Company's No. I Hudson, Coleman County, was the discovery well of the Silver field, with a total depth of 3540 ft.; initial production, 10,000,000 cu. ft. of dry gas and 60 bbl. of oil per day from the Gray sand, topped at 3482 ft. The first well drilled in the new Jim Ned field was the Merry Bros. and Perini No. I Greer, also in Coleman County. It had a total depth of 3937 ft. and an initial production of 152 bbl. of 42" gravity oil in 6 hr., through I-in. choke, from Gray sand encountered from 3909 to 3937 feet. J. E. Farrell's No. I Rose, Haskell County, was a new discovery, around which no additional wells have been drilled. Total depth was 3002 ft., plugged back to 2780 ft. to test an oil sand encountered from 2663 to 2685 ft., which when perforated with 76 shots at that depth was good for 85 bbl. of 40" gravity oil. In Fisher County, General Crude drilled its No. 12 Flanagan to a total depth of 6746 ft. After plugging back to 4578 ft. to test a sand encountered from 4515 to 4528 ft. it was abandoned as a dry hole. The top of the Ellenburger was reported as 6094 feet. Interest in Jones County continued unabated, largely through the development of the Wimberly pool in the southern part of the county, where five Cisco sands are producing. At present the pool has been defined on the south and the southwest. The structure has 170 ft. of closure; the lower limestone pays producing on top of the structure and the fist pay encountered, the Akard sand, producing on the flanks of the structure. Five deep wells were drilled in Stonewall County (H. and T.C. survey)—the Shell Oil Company's No. I-A Patterson, in block D, with a total depth of 6827 ft., dry and abandoned; the Shell Oil Company's No. I Rutherford, block I, with a total depth of 6239 ft., dry and abandoned; the Leader Oil Company's No. I Bilberry, block D, with a total depth of 5700 ft., dry and abandoned; Forest Development Company's No. 2 Boyd, block D, with a total depth of 4753 ft., dry and abandoned; and the Hunter et al. No. I Boyd, block D, total depth 4757 ft., dry and abandoned. J. E. Farrell drilled his No. I Tipton south of a well that produced from a Strawn sand for some time, to a total depth of 5202 ft., where it was abandoned. The well is in the southwest corner of sec. 43, block 19, T. and P. survey, Nolan County.

Jan 1, 1942

By H. W. Schadler

Single crystals of tungsten, which were grown by electron bombardment floating zone refining, were strained 2 pet in tension and bending at 298°, 77°, and 20°K to determine the modes and crystallography of the plastic deformation of these temperatures. At 77° and 20°K plastic deformation occurs by slip on systems of the type (011) [111] and by twinning on (112)-type planes. For crystals strained at 298°K, deformation occurs by slip in [111] directions on either (Oil)- or (112)-type planes. CURRENT models for the initiation of brittle fracture in crystalline materials are based on a knowledge of the details of their plastic deformation.1 Body-centered cubic tungsten exhibits brittle failure at temperatures below about 500 °K yet the modes and crystallography of its plastic deformation have not been studied below 1000°K. In 1924, Goucher2 reported that tungsten single crystals with a total impurity content of less than 0.01 wt pet deformed by slip on the (112) [111] system in the temperature range 1000° to 3000°K. He also observed (001) [010] slip in one crystal which was constrained by the presence of a large fissure. According to Barrett3 tungsten also deforms by twinning on the (112) plane in the [111] direction, but he gives no details on the tendency for twin formation or the temperature range in which twinning occurs. Therefore, as a necessary part of a study of the factors influencing the brittle fracture of tungsten, the modes and crystallography of the plastic deformation were determined at 298°, 77°, and 20°K. Tungsten single crystals, grown using the electron-bombardment zone-refining technique first described by Calverly,4 were deformed to between 1 and 2 pet plastic strain in tension and bending. The surface offset resulting from slip or twinning was observed with an optical microscope to determine the crystallography of the deformation. The existence of twins was proven by the standard polishing and etching technique; and the crystallography of dislocation motion was followed using the dislocation etchant described by Wolff.5 Some observations on the fracture characteristics of tungsten single crystals are included. EXPERIMENTAL TECHNIQUES Growth, Purity, and Perfection of the Crystals-Several years ago Calverly, Davis, and Lever4 dem-onstrated the feasibility of growing tungsten single crystals by the electron-bombardment floating zone-refining technique, and Carlson6 showed that crystals produced in this way had a high degree of purity and were ductile at room temperature. Tungsten single crystals produced by this technique in equipment similar to that described by Carlson were used in this study. The starting material, a powder metallurgy product, was obtained in the form of a swaged 1/8-in. rod from the General Electric Wire Plant in Cleveland, Ohio. The crystals were grown from this material in a vacuum of 10"4 mm of Hg by passing a molten zone 1/8 in. long down the rod twice at a speed of 3 mm per min. At this zone speed

Jan 1, 1961

By P. B. Crawford, W. L. Huskey

A study has been made to determine the effects of random vertical fractures existing in a reservoir matrix on the effective matrix properties and producing characteristics of a well. The study indicated that short vertical fractures may distort the isopotentials by 1 percent in the vicinity of the fracture. A correlation was developed which showed the effect of fracture density on the producing capacity of a well. The correlation indicated that fracture shape had little effect on producing capacity, but that total fracture length was closely correlated with the producing capacity. Effective values of reservoir permeability were found to correlate closely with fracture density when measured parallel to the direction of flow. INTRODUCTION In reviewing the petroleum literature, it is found that in most analytical solutions of hydrocarbon reservoir behavior the assumption is made that the rock is uniform throughout although core analysis and well logging surveys indicate that substantially all reservoirs are heterogeneous and some are fractured. Only in recent years have investigators studied the effects of reservoir hetrogeneity. Russell1 discussed the effect of fractures in reservoirs. The literature indicates that fractures greatly affect the exploitation of man reservoirs. This is described by Elkins and Skov2 and Little-field et al. 3 Several types of reservoir heterogeneity have been studied by unsteady-state methods. In 1959, Landrum et al. 4 showed that transient phenomena in hydrocarbon reservoirs could be studied by thermal models. pickering5 studied the flow of heat in stratified linear reservoirs consisting of plates of different metals separated by sheets of rubber which were suddenly exposed to a low-temperature source at one end. Cotman6 studied both laterally and vertically heterogeneous thermal model reservoirs with special reference to cross flow. Another type of reservoir heterogeneity involves the presence of highly permeable, circular lenses around or near the wellbore which was studied by Miesch7 using a thermal and a steady-state model. Many studies have been made of the effects of induced hydraulic fractures on well performance. 8-10 Work regarding vertical fractures that exist initially in the reservoir was reported by Givens, et al.11 Since there appears to be little published work on the importance and influence on reservoir performance of fractures that exist out in the rock matrix, this study was conducted to determine the effects of vertical fractures on pressure distribution, producing capacity and the effective permeability of the reservoir rock. The analogy between the flow of electrical current through a conducting body and the flow of fluid in a porous medium provides a convenient method of studying various aspects of petroleum reservoirs. For electrical radial steady-state flow,12 For steady-state fluid flow, With the above analogy, it is only necessary to establish the ratio of the values of the electrical units in terms of the corresponding flow units to make the analogy quantitative. The ratios are shown below.

By T. Saburi, C. M. Wayman

The massive and martensitic transformations in ß Cu-Ga alloys were studied by optical microscopy and by transmission electron microscopy and diffraction. These types of transformation are distinct and do not merge into one another. An internal fine structure due to stacking faults was found in both the massive phase (m) and the martensite, but the origin of the faults is believed to be different in each case. The faults in the martensite are due to the lattice invariant or "second" shear of the phenom-enological theory, while those in the are probably growth faults and deformation faults arising from the transformation volume change. Evidence is presented for ordering in the ß phase prior to transformation into martensite, and the crystal structures of and ß' and ßi martensites are discussed. THE results from some previous investigations1,2 have led to the suggestion that martensitic and massive transformations have certain common characteristics. It presently seems established that massive transformations like martensitic transformations are essentially diffusionless,1,2 but unlike martensitic transformations, when a new phase forms massively there is no shape change or surface relief.= If the massive-type transformation is crystallographically similar to martensitic transformations, one would expect a fine structure as a result of the lattice invariant shear4 which is a part of the transformation mechanism. The existence of such a fine structure (i.e., slip, twinning, or faulting), if any, can be verified by transmission electron microscopy, and thus the present investigation was undertaken to compare the internal structure of massively and martensitically formed phases in Cu-Ga alloys which were derived from a parent of the same composition. The transformation characteristics of ß Cu-Ga alloys were also studied. The bcc ß phase in the Cu-Ga system, Fig. 1, is stable above 616oc.' Depending upon the cooling rate, ß Cu-Ga alloys can undergo three different types of phase transformations. The ß phase of eutectoid composition (23.7 at. pct Ga) decomposes into the ? phase (hcp) and the phase (complex cubic) by means of a eutectoid reaction. When the cooling rate is increased so that the decomposition of 0 into [ and ? is suppressed, the ß phase transforms into a nonequilibrium hcp phase, herein denoted ?m by a process of very rapid growth called a "massive" transformation. At even faster quenching rates the massive transformation can be suppressed and the ß transforms martensitically. Massive transformations, apparently similar to those in the Cu-Ga system, have also been studied in the Cu-Zn2,6-8 and Ag-Cd systems.9 Definitive characteristics if the Massive Transformations in 0 Cu-Ga Alloys1 1) The most remarkable feature of the massive transformation in Cu-Ga is that there is no bulk composition change on transformation. According to Massalski,1 the resulting [, phase is a supersaturated extension of the equilibrium [ phase. The lattice parameters continue the trend exhibited

Jan 1, 1965