Search Documents

By L. Ibagos S., T. Balberyszski

The volumetric flow rate and the initial concentration of the copper sulfate solution influence the rate of reaction and, hence, the precipitation efficiency in a continuous launder cementation system. Using a model of such a system it was found that the precipitation efficiency is related to the two process parameters by the approximate expression [ log [1-n] = -[0.072 co 2.91 e – 0.511c o Q 1.15 ] N Q] where c is the initial concentration, Q, is the volumetric flow rate and N is the number of launders in the system. This expression agrees with an equation developed for the rate of the cementation process if it is assumed that the exponential factor represents the change in the surface area with concentration and the exponents 2.91-and 1.15 relate the hydrodynamic conditions and the surface concentration to co and Q. The experimental results are used to determine the values of a Precipitation Coefficient for any volumentric flow rate and initial concentration of solution. Knowing the Precipitation Coefficient, the total volume of launders that will result in a given precipitation efficiency can be calculated. It is established that maximum precipitation efficiencies are obtained for initial concentrations between 6.0 and 7.0 gpl and volumetric flow rates of approximately 350 m3 /hr Good agreement between calculated and actual launder volumes is obtained for a number of industrial operations for which a comparison is made.

Jan 1, 1973

By Morris Muskat

It is pointed out that the application of capillary pressure curves obtained by drainage or desaturation processes to the calculation of the fluid distribution in interphase transition zones involves a number of difficulties; namely: (I) the development of very low nonwetting phase saturations appears to be in contradiction with the lack of mobility of such distributions indicated by permeability-saturation curves, (2) dispersed nonwetting phases are thermodynamically unstable, and (3) discontinuous phases should not be subject to hydrostatic equilibrium requirements. While these difficulties could be obviated by assuming that the capillary pressure drainage curve has an initial horizontal segment, they are automatically circumvented by application of the imbibition capillary pressure curve to the lower part of the water-oil transition zone. These generally show zero displacement pressure at only partial wetting-phase saturations. The countercurrent upward flow of oil into the main oil-saturated pay and downward drainage of water also suggests that wetting phase imbibition processes will control the saturation distribution immediately above the water-saturated section. Similar considerations, with a generalized interpretation of the apparent wetting-phase behavior of the oil and gas phases, provides a basis for constructing the curve for fluid distribution in the oil-gas transition zone. In the transition zones so derived, the oil begins with a nonvanishing saturation at the water-oil contact and terminates with a similar saturation at the top of the gas-oil contact. The gas-oil transition zone begins with an equivalent nonvanishing gas saturation. Introduction It has been a common assumption for some years that the nature of the fluid dis- tribution in virgin reservoirs, and in particular that in the transition zones between the oil and water and between the oil and gas sections, can be computed by a simple application of capillary pressure data. The results of such calculations appear to have been first reported by Leverett.' The latter, however, indicated only the numerical values of the parameters used in the computations, without explicitly describing the procedure. Leverett's illustrative calculated transition zones are reproduced in Fig I. Although no critical study of the apparently obvious method of calculation has been published, one cannot proceed very far in the computation without encountering some rather fundamental questions not yet answered in the literature. This paper is not written under the pretense that the whole transition-zone problem has been fully and satisfactorily solved. Its purpose, rather, is to discuss suggestions for its treatment, much of it admittedly hypothetical, and emphasize the nature of the uncertainties arising therein; for the literature, as now available, gives little indication that there are any problems still outstanding. The Transition-zone Equation The basic equation, which presumably gives directly the fluid distribution without recourse to any further consideration, is: Ap = (r1 - r2)gh [1] where r1, y2 are the densities of the two contiguous fluids, h is the height above the "capillary-free" zone of complete saturation with fluid I, g the acceleration of gravity, and Ap is the capillary pressure across the average interface at the height

Jan 1, 1949

By Arthur Tauber, Horst Kedesdy

FERRITES are sintered metallic oxides of the spinel structure type1 and belong to the class of soft ferromagnetic materials. Similar to a ceramic, they can be formed and fired to a dense body, exhibiting a high electrical volume resistivity ranging from 102 to 102 ohm-cm as compared with 10-6 ohmcm for some of the metallic magnetic materials. This high resistivity, with resulting low eddy current losses, finds special application at high frequencies. The dispersive susceptibility of ferrites at microwave frequencies has also led to many applications in this field. Where high resistivity with high permeability is desirable, ferrites are used in low frequency applications. During the last few years ferrites exhibiting rectangular hysteresis loops have been developed for computer and magnetic memory systems. The general formula for ferrites is MeFe2O4 where Me is a divalent metal ion such as Ni, Zn, Mg, Mn, Cu, Cd, and Fe. Only two of these ferrites are nonferromagnetic, namely, those with Zn and Cd. Solid solutions can be formed between different ferrites, and it is of interest to note that solid solutions of a ferromagnetic ferrite with a nonferromagnetic ferrite yield much better magnetic materials than the basic ferrite body. In general, it can be said that the solid solution formation between ferrites has widened the field of ferrite synthesis and has led to methods of preparing materials with a large variety of magnetic properties.

Jan 7, 1957

By H. O. Hofman

Lime-roasting is a term proposed by Ingalls' for the operation of forcing air under pressure through a mixture of galena and lime at the kindling-temperature with the object of oxidizing lead and sulphur and of fritting or fusing the charge. If finely-divided galena were treated in this manner without the addition of lime, the heat set free by the oxidation of part of the lead and the sulphur would be sufficiently great to fuse un-decomposed sulphide, and thus stop desulphurization. Besides the chemical action that the addition of lime, limestone or gypsum to the charge may have, the admixture has the physical effect that it keeps the particles of galena separated from one another and accessible to the oxidizing effect of the air. At present, three methods of lime-roasting are carried out on a working-scale,—the Huntington-Heberlein, the Carmichael-Bradford and the Savelsberg2 processes. In the last, which interests us here, an 8-ton charge is made up of galena, limestone and perhaps some siliceous or ferruginous flux; the whole is crushed to pass a screen with 3-mm. holes and moistened with 5 per cent. of water. It is fed gradually into a bowl-shaped converter, 6.56 ft. in diameter, supported by trunnions attached to a truck. On the bottom the converter has a grate with blast-inlet beneath. In starting, the truck with the converter

Jan 1, 1908

By G. Barbery

Since the original paper, two methods have been introduced to compute the parameters of the three parameter size distribution equation: [ ] Both of them are based on graphical means, which are time-consuming and of little statistical significance. A program has been developed, using the Gauss-Newton method to compute by nonlinear regression analysis the parameters of the equation. Although the method is quite general in curve-fitting applications, it does not appear to be used in the field of size analysis, and a brief description is given. As applied here, the Gauss-Newton method involves the minimization of the least squares: [ ] where n is the number of sieves used. The second member of Eq. 2 can be approximated by a multiple Taylor's series expansion of first order about a starting value [ ] The minimization of Q (r,s,Xo) means: [ ] Putting Eq. 3 into Eq. 2 and differentiating, we obtain a system of equations which can be represented in matrix symbolism (box) The system can be solved for: [ ] and the operations repeated with new values: [ ] The starting values for r and s are taken as 1, for Xo, a value higher than the maximum sieve opening value. Applied to the data given by Herbst 5,6 for batch grinding of 7 X 9 mesh dolomite, the parameters given in Table 1 were obtained. The discussion of the significance of the residual sum of squares is a difficult subject in multiple nonlinear

Jan 1, 1972

By D. J. Schmatz, H. I. Aaronson, H. A. Domian

Diffusion kinetics in disordered hcp Cd-Mg alloys have been investigated by means of the Kirkendall effect and concentration-penetration curves determined with an electron-microprobe analyzer. Self-diffusion coefficients of both species were determined at the three marker compositions obtained, averaging 27.6, 46. 7, and 78.1 at. pct Mg, by means of the Darken analysis. These coefficients were then corrected for the unequal and concentration-dependent partial molar volumes of the two elements with the Balluffi analysis, and for the vacancy flux effect by the Manning analysis. The latter correction reduced the Balluffi correction produced larger changes in the self-diffusiv-ities; neither, however, produced statistically significant changes in the Do's or the H'S. The most striking result of this investigation is that at all three compositions and at all temperatures studied both the uncorrected and corrected self-difjusivities of magnesium are higher than those of cadmium. The Cd-Mg system is the first one found in which the higher melting, lower vapor pressure element diffuses more rapidly. Both an empirical correlation due to Toth and Searcy and considerations of the atomic mechanism of diffusion indicate that this anomaly is probably due to a comparatively low value of the activation energy required for a magnesium atom and a vacancy to exchange sites, perhaps occasioned by the higher compressibility of magnesium atoms. KIRKENDALL effect studies have been previously reported for only two hcp solid solutions: the E phase of the Zn-Cu system1 and the a phase of the Cd-Hg system.' In neither investigation were the marker-movement studies supplemented with the concentration-penetration curve determinations necessary to evaluate self-diffusivities by means of the atano and the Darken analyses. The present program was undertaken to obtain both types of data on a hexagonal solid solution in order to provide more detailed information relevant to the mechanism of diffusion in this type of lattice. The Cd-Mg system was chosen for this study because the disordered solid solution extends across the entire phase diagram at temperatures above 253"c5 and the substantial difference in the melting points of the component pure metals promised that marker movements would occur at reasonably rapid rates should the diffusivities of the two species be as unequal as might be anticipated. The experimental convenience of the relatively low melting points of cad-miun and magnesium and the availability of extensive and accurate activity data6 (required for application of the Darken analysis) were additional reasons for selecting this alloy system. Since the anisotropy of diffusion is not large in either pure cadmium7 or pure magnesium,' the diffusion couples were prepared from polycrystalline components. The presence of a well-defined texture in the couples—the c axis of individual crystals tended to be normal to the diffusion direction— however, provides a fair degree of crystallographic definition to the data obtained. The principal (and entirely unexpected) finding of this investigation, that magnesium, the high-melting low-vapor pressure element, diffuses more rapidly than cadmium, in contradiction to a broad range of results in fcc and bcc alloys, as well as in the previously studied hcp alloys,172 makes the self-diffusivity determinations of immediate interest in understanding the origin of this anomalous result. EXPERIMENTAL PROCEDURE The cadmium (Belmont Smelting and Refining Co.) and magnesium (Dow Chemical Co.) used in this study were both of 99.99 pct purity. Alloys containing 51.0 and 65.6 at. pct Mg were prepared from these materials by melting under a MgC12-base flux in a high-purity graphite crucible. These alloys were subsequently hot-worked and then homogenized in a helium atmosphere at temperatures close to their solidus points. Sandwich-type diffusion couples of the type g/d/g were prepared from the pure metals by solid-state diffusion. Two-piece alloy couples of Mg/65.5 at. pct Mg (Mg/gCd) and Cd/51.0 at. pct Mg (Cd/CdMg) were welded by a liquation technique. The individual components of both types of couple were initially cylinders 1.27 cm in diam and in length; the ends of these cylinders were machined accurately flat and parallel. For both welding techniques, the pure cadmium cylinders and the alloys were chemically polished in a mixture of 40 pct ethyl alcohol, 40 pct hydrogen peroxide (30 pct conc), and 20 pct nitric acid,g while those of pure magnesium were polished in a solution of 10 pct nitric acid in ethyl alcohol.' Immediately afterwards, both metals were rinsed in freshly distilled acetone, and then in similarly purified methanol.' The Mg/Cd/g couples were assembled in a carefully cleaned stainless-steel welding fixture, in which a screw operating through a self-centering arrangement permitted a controlled pressure to be exerted upon a couple prior to welding.'' Tungsten marker wires 0.005 cm in diam were placed at the d:g interfaces of some of these couples, and imbedded in the couples during the application of pressure. As soon as a couple had been assembled, the welding fixture was inserted into a Pyrex capsule containing a packet of zirconium chips at each end. The capsule

Jan 1, 1967

CHARLES KIRCHHOFF, Chairman. ALBERT SAUVEUR, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, J. Esrey Johnson, Jr., Felix A. Vogel, William H. Blauvelt, William Kelly, Leonard Waldo, James Gayley, . Richard Moldenke, William R. Walker, Henry D. Hibbard, Joseph W. Richards, - William R. Webster. Henry 1%1. Howe, E. Gybbon Spilsbury, Frederick W. Wood. Robert W. Hunt, A. A. Stevenson, The Board of Directors of the Institute has authorized the holding of a meeting under the auspices of the Iron and, Steel Committee in New York City, October 16 and 17, 1913. Gratifying responses have been received to the request of the Committee for contributions, the following papers being already assured: 1. H. M. Howe, Equilibrium Temperature for A, in Carbon Steel. 2. H. M. Howe, The Divorcing of the Eutectoid in Meteorites. 3. H. M. Howe and A. G. Levy, Determination Of the Position of Ae3, in Carbon-Iron Alloys. 4. G. .K Burgess, J. J. Crowe and H. S. Rawdon, Thermal and Microscopical Examination of Professor Howe's Standard Commercial Steels. 5. H. Dl. Hove, Discussion of the Existing Data as to the Position of Ae3,. 6. J. H. Hall, Shock Tests of Cast Steel. 7. H. F. Miller, Jr., The Design of Regenerators for Open-Hearth Furnaces. 8. E. Stütz, Paper on the "Scoria Process." 9. Albert Sauveur, Mayari Steel. 10. Felix A. Vogel, Briquetting. 11. J. E. Johnson, Jr., Paper on " Cast Iron."

Jan 6, 1913

By R. L. Vaughn, A. G. Moon

In 1972 a major renovation of the flotation and regrinding circuits was completed at Kennecott Copper Corporation's Chino Mines Division concentrator at Hurley, New Mexico. At that time a new lime distribution and control system was placed in operation. Lime is used to depress pyrite, and flotation at a high pH or alkalinity is required for optimum recovery of principal copper minerals, chalcopyrite and chalcocite with good rejection of the pyrite. Regrinding is also required to liberate chalcocite, much of which occurs as intimately associated chalcocite-pyrite middling grains. Accurate control of the lime addition is necessary to obtain both optimum metallurgy and minimum lime usage. At low pH levels, flotation cell control is difficult due to excess froth, but excessively high pH levels can go unnoticed because froth characteristics do not change from those experienced at the desired pH. With manual control of the lime addition, the desired pH can be exceeded for periods of up to two hours. Test Work Plant test work on a lime control system using conventional pH probes gave disappointing results with high electrode maintenance and poor control characteristics. For example, the rougher flotation cells are operated at a pH between 11.4 and 11.6 and the probes required cleaning at least once a day, and occasionally every shift. These high maintenance requirements were considered unreasonable for a plant-wide system using six or more control loops.

Jan 1, 1979

By F. von Gemmingen, E. J. Fasiska, L. Zwell

EARLIER studies of the dependence of creep on structure1 and of the dependence of creep rupture on creep behavior2 did not include detailed discussion of the phases present in the specimens under examination. It is of interest to determine the nature and amounts of such phases present since it is well known that these are dependent on composition, heat treatment and creep conditions.3 This investigation has therefore been undertaken to identify these constituents and to determine their relative amounts. This report presents the results of this investigation and describes an improved "extraction replica" technique developed in the course of the work. The composition of the Type 316 austenitic stainless steels studied in this investigation is given in Table I. The specimens were solution treated at 2000°F for 1/2 hr and water quenched. Those specimens subjected to prestrain at room temperature Methods for extracting precipitate particles from materials for electron and X-ray diffraction analysis have been described by Fisher,4 Smith and Nutting: and Booker and coworkers.6'7 Electrolytic extraction methods have been described by Andrews and Hughes.8 The first two methods have been used at this Laboratory, but have not proved satisfactory for many problems requiring X-ray diffraction analysis. It has been difficult to remove the replicas or to avoid tearing them during removal. These difficulties are overcome by backing the replica with a water-soluble plastic such as Dupont 51-05 Elvanol (polyvinyl alcohol). The backing increases the thickness of the replica so that it can be mechanically stripped from unloosened particles without folding or tearing. This procedure eliminates the stripping of wet replicas, which usually have a low tear strength. By stripping replicas after drying, it is possible to extract partially loosened particles which otherwise would remain imbedded in the metal. The modified method is as follows: after the specimen is polished, it is etched for 60 min in modified glyceregia consisting of 30 ml glycerol, 7 ml nitric acid, and 4 ml of hydrochloric acid. The sample is then washed, air dried, and coated with a 20 pct Baker and Adamson 1611 collodion (85 pct amyl acetate by volume) film. After the collodion film is dry (about 15 min), the sample is again etched in the modified glyceregia for 50 min, washed with isopropyl alcohol (to prevent dissolving the collodion) and air dried. A very thick coat of polyvinyl alcohol (about 50 pct solution "Elvanol Dupont 51-05" in water) is poured over the sample and is permitted to dry for about 24 hr. The composite film containing the precipitates is then stripped from the specimen and floated, polyvinyl alcohol side down, in water (at about 50°C) until the polyvinyl alcohol dissolves. This usually takes about 15 min. Should any of the polyvinyl alcohol remain on the replica, it does not give a crystalline diffraction pattern and therefore does not hinder identification of the precipitates. The extraction replica, floating in water, is picked up on a glass fiber and mounted in the Debye-Scherrer camera for X-ray diffraction analysis. Concentration of the etchant, and also etching time, had to be increased for several of the samples. Fig. 1 shows two extraction replicas taken from different areas of spec. M74-37; X-ray analysis showed a strong diffraction pattern of M23C6 and a medium one of u phase. A

Jan 1, 1962

By Charles E. Lundin

Pressure-temperature-composition data were obtainedfor the Er-H system. Measurements werecar-ried out in the temperature range of 473° to 1223°K, the composition range of erbium to ErH,, and the pressure range of 10-5 to 760 Torr. Solubility relationships were established from these data throughout the system. Three solid-solution phases were delineated: metal solid solution, dihydride phase, and trihydride phase. The trihydride Phase decomposes at about 656°K and 1 atm pressure. The dihydride phase is stable to about 1023°K, but becomes more deficient in hydrogen above this temperature. The equilibrium decomposition pressure-temperature relationships in the two-phase regions, erbium solid solution plus dihydride and dihydride plus trihydride, were deter- The differential heats of reaction in these two regions are AH = - 52.6 * 0.3 and - 19.8 i 0.2 kcal per mole of Hz, respectively. The differential entropies of reaction are AS = - 35.2 * 0.3 and - 30.1 * 0.4 cal per mole HZ.deg, respectively. Relative partial molal and integral thermodynamic quuntities were calculated in the system to the dihydride phase. RARE earth metal-hydrogen systems have been the subject of general survey,1"4 and all have been found to form hydride phases. The heavy rare earths, of which erbium is a member, form dihydride and trihydride phases with different crystal structures, whereas the light rare earths form only a single-phase dihydride which expands without structure change, as hydrogen is added, to the trihydride composition. These materials are of interest primarily because of their theoretical properties, such as bonding, defect structure, and thermodynamic and electronic characteristics. Erbium has been studied in several previous investigations.5, 6 It was deemed desirable to more thoroughly and accurately define the system, both for the phase equilibria and the thermodynamic properties. I) EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus was employed to conduct the experimental measurements. Briefly, it consisted of a source of pure hydrogen, a precision gas-measuring buret, a heated reaction chamber, a mercury manometer, and two McLeod gages (a CVC, GM 100A and CVC, GM 110). Pure hydrogen was obtained by passing hydrogen through a heated Pd-Ag thimble. The hydrogen was analyzed and found to have only a trace of oxygen and nitrogen. A 100-ml precision gas buret graduated to 0.1-ml divisions was used to measure and admit hydrogen to the reaction chamber. The reaction unit consisted of a quartz tube surrounded by a nichrome-wound furnace. The furnace temperature was controlled by a recorder-controller to ±1°K. An independent measurement of the sample temperature in the quartz tube was made by means of a chromel-alumel thermocouple situated outside, but adjacent to, the quartz tube near the specimen. Pressure in the manometer range was measured to ±0.5 Torr and in the McLeod range (10-4 to 10 Torr) to ±3 pct. The hydrogen compositions in erbium were calculated in terms of hydrogen-to-erbium atomic ratio. These compositions were estimated to be ±0.01 H/Er. The erbium metal was obtained from the Lunex Co. in the form of sponge. The metal was nuclear grade with a purity of 99.9 pct +. The oxygen content was reported to be 340 ppm and the nitrogen not detectable. Metallographically the structure was almost free of second phase (<1 vol pct). A quantity of sponge was arc-melted for use as charge material. The solid material was compared with the sponge in the pressure-temperature-composition relationships. They were found to be identical. Therefore, sponge material was used henceforth, so that equilibrium could be attained more rapidly. The specimen size was about 0.2 grain for each loading of the reaction chamber. The procedure employed to obtain the pressure-temperature-composition data was to develop experimentally a family of isothermal curves of composition vs pressure. First, a specimen of erbium was wrapped in a tungsten foil capsule to prevent contact with the quartz tube. After loading the specimen, the system was evacuated to less than l0-6 Torr, flushed several times with high-purity hydrogen, and evacuated again ready for the start of the experiment. The furnace was then brought to the desired temperature. A measured amount of hydrogen was admitted into the chamber. Equilibrium was allowed to be attained, the pressure read, and the process then repeated many times until 1 atm of gas pressure was finally reached. Other isotherms were then developed in the same manner. The partial pressure plateaus were determined by another manner. In the solid solution-dihydride region a composition of approximately 1.0 H/Er was selected on the plateau. The temperature was varied throughout the range of interest. At each temperature level, equilibrium was achieved, the pressure read, and the next temperature attained. The temperature was cycled both up and down. In the dihydride-trihy-dride region, the plateaus were determined in the 473" to 651°K range only by heating to the desired temperature and not by both heating and cooling. The data were much more reproducible in this manner. Equilibrium required long periods of time. Specimens were initially hydrided to 2.8 H/Er, so that at the higher

Jan 1, 1969

By T. E. Leontis

ONLY a limited amount of information has been published on the effect of thorium as an alloying ingredient in magnesium. McDonald13&apos;2 showed that the addition of thorium in amounts up to 3 pct increases significantly both the ductility and the strength of rolled magnesium sheet. A recent publication by Sauerwald" indicates that thorium contributes strength and creep resistance at elevated temperatures to magnesium in both the cast and wrought states. The observations of Sauerwald are confirmed in this paper, which presents the results of a systematic study of the effects of compositional variation on the tensile properties, creep resistance, conductivity, density, and metallography of Mg-Th alloys containing up to 50 pct Th both in the sand-cast and in the extruded states. The effect of the addition of cerium to Mg-Th alloys is also reported. Experimental Methods The alloys studied in this investigation were pre.pared in small laboratory melts according to the melting practice described by Nelson4 as the crucible method. Electrolytic magnesium was used as the starting material to which the thorium* was introduced in metallic form. It was observed that the behavior of thorium in molten magnesium with respect to reaction with protective fluxes is similar to that of rare-earth metals. In order to obtain the highest possible alloying efficiency, it is necessary to use non-MgC1, fluxes and to apply all the precautions described by Marande6 for melting, alloying, and casting magnesium-rare-earth alloys. .Under these conditions it is possible to obtain an alloying efficiency in the range of 85 to 95 pct. The Mg-Th-Ce alloys were made with cerium of the highest purity available, not with the commercial product "misch-metal" which contains approximately 50 pct Ce. The total rare-earth content of this material was 97.1 pct, of which 0.3 pct was rare-earth metals other than cerium; the major impurities comprising the balance were iron and magnesium. The thorium and cerium contents of each alloy were determined chemically. Test bars 6% in. long with a 2% in. long reduced section of % in. diam were cast in sand molds using a four-baf pattern. In most cases, a 3 in. diam extrusion billet 10 in. long was cast in a steel mold from the same melt used for making the sand-cast test bars. For the higher thorium alloys, it was necessary to remelt the foundry scrap from the test bars in order to make the extrusion billets. The billets were scalped to a diameter of 2 15/16 in. and the ends faced to a length of 9% in. as limited by the size of the extrusion container. The alloys were extruded into % in. diam rod on a 500-ton direct-extrusion press. The details of the extrusion process are as follows: Billet preheat 925°F (2 to 16 hr) Container temperature 900 °F Die temperature 900°F Extrusion speed 10 ft per min Reduction ratio 36:1 Percent reduction 97.3 Alloys containing up to 10.2 pct Th were preheated at 925°F for 2 hr; all alloys with higher thorium contents were preheated for 16 hr. In order to establish the effect of extrusion temperature, billets of

Jan 1, 1953

By A. Totani, S. Nakajima, H. Okazaki

The phase diagram for the SnTe-SnSe system has been studied in the temperature range from 300° to 900°C by differential thermal and quenching techniques. The X-ray measurements were made on quenched specimens. High-temperature diffraction was also made to study the phase transition in SnSe. The system is proved to be of a eutectic type in which no intermetallic compound exists. The eutectic point is at the composition SnTeo.55 Seo.45. the eutectic temperature being 755°C. Solid solubility limits are SnTeo.6Seo.r and SnT eo. 3s Seo.6s at the eutectic temperature, and change almost linearly to SnTeo.aaSeo.lz and SnTeo.18 Seo.az as temperature decreases to 300°C. It was shown that the SnSe phase has a phase transition of the second order at about 540°C and that the transition temperature decreases with increase of the SnTe content. THERMOELECTRIC properties of tin telluride (SnTe) and tin selenide (SnSe) have been studied extensively in recent years. The variation of physical properties with composition could be of interest if these compounds form an appreciable crystalline solution. The purpose of present investigation is to confirm the formation of crystalline solution or intermetallic compound, if any, and to establish the phase diagram for this system. The crystal structure of SnTe is NaCl type with a cubic unit cell1 (a = 6.313A). The crystal of SnSe having an orthorh2mbic unit cellz (a = 11.496, b = 4.1510, and c = 4.4437A) is isomorphous with tin sulfide (SnS) which has a distorted sodium chloride structure. It has been known that SnSe has a phase at at 540°C; the transition has been assumed to be of the second order. As far as we know, only two studies on the SnTe-SnSe pseudobinary system have been reported. The conclusion obtained in these papers is that, in the composition regions near SnTe and SnSe, the system forms a crystalline solution of the SnTe structure and the SnSe structure, respectively, and that, in the intermediate region, both phases coexist. However, neither the variation of the solid solubility vs the temperature nor the liquidus and solidus were investigated. Hence present writers have attempted to determine the phase diagram of the system by differential thermal analysis (D.T.A.) and X-ray diffraction. EXPERIMENTAL Sample Preparation. Starting materials, SnTe and SnSe, were prepared by the direct fusion of commercially available high-purity (99.999 pct) elements. Stoichiometric amounts of each couple Sn-Te or Sn-Se were weighed into a clear fused silica ampule. After evacuation to a pressure below 10-3 mm Hg, the am- pule was sealed, and annealed at 900°C for 5 hr. The melt was quenched in water. X-ray analysis confirmed the formation of a single phase of SnTe or SnSe. The other samples, SnTel-,Sex were synthesized from these SnTe and SnSe by mixing them in the required ratio, followed by annealing at 900°C and quenching. These samples were used directly for D.T.A. For X-ray measurements, samples were annealed at 700°, 600°, or 500°C for 100 hr or at 300°C for 150 hr, and then quenched in water. It was found that the lattice constants of the SnTe phase annealed for 150 hr at temperatures above 500°C did not differ from those annealed for 100 hr at the same temperatures. However the X-ray phase analysis showed that at 300°C the annealing for 150 hr was necessary to attain a true equilibrium state. D.T.A. The solid-liquid equilibrium temperature was determined from D.T.A. measurements. The sample was sealed in an evacuated silica tube and molybdenum powders sealed in an another tube were used as a reference material. The sample and the reference tube were placed in a nickel block and were heated from room temperature to 900°C at a rate of 3°C per min and then cooled down at the same rate to 600°C. Thermocouples for these measurements were Pt-Pt. Rh (10 pct) and the error of temperature measurements was within + l0C. D.T.A. curves were obtained on a two-pen recorder and an automatic controller (PID type) was used for the program of heating and cooling. When temperature reaches the solidus from the low-temperature side, there appears an endothermic peak. The solidus temperature was determined by extrapolation of the straight portion of the starting flank of this peak to the base line. In a similar way, the liquidus temperature was determined from an exothermic peak on D.T.A. cooling curve. In the case of supercooling, if any, its degree can be estimated from the magnitude of the abrupt temperature rise. X-Ray . X-ray powder patterns were taken by a diffractometer using CuK, radiation. Since the SnSe crystal is cleaved easily, the powders become flaky when SnSe-rich samples are ground in an agate

Jan 1, 1969

By Lester Blackner

THE PROPERTY AND LOCATION THE Ray Consolidated Copper Co.&apos;s mining property is located on Mineral Creek 6 miles north of Kelvin, at Ray, Pinal County, Ariz. (Fig.. 1) . The mining claims now owned by the company consist of 126 lode claims, comprising 2,144.9 acres, containing at the beginning of operations 82,904,368 tons of 2.19 per cent. copper ore. GENERAL CHARACTERISTICS OF THE OREBODY The main orebody is a disseminated deposit in schist and porphyry formed by secondary enrichment. Its existence was proved by churn drilling, and it is at present one of the largest proved copper deposits in the world. The orebody itself covers .205 acres with an average thickness of 121 ft., and occupies a definite belt which has a northwest direction. Its length is approximately 5,000 ft. The width varies, being about 2,000 ft. at the west end and 2,500 ft. at the east, narrowing down irregularly front both ends to a few feet in the center. The thickness of the body varies greatly along the line of lode, ranging from a few feet up to 470 ft. thick. The ore horizon is not constant, but varies, following in a broad sense the topography The body in general dips slightly to the northeast, and is broken up by numerous small faults and fractures. The ore-bearing formations, consisting of mineralized schist and mineralized granite porphyry, stand fairly well and offer no difficulty in mining operations.

Jan 6, 1915

By R. W. Smith

There are many inconsistencies and gaps in available information concerning the mechanism whereby dodecylamine acts as a collector for quartz. The author compares the studies which have been made in correlating the contact angle with adsorption density on quartz over all pH ranges, and attempts to resolve some of the inconsistencies. In recent years much information has been obtained concerning the mechanism whereby dodecylamine acts as a collector for quartz. Fuerstenau,1 for ex- ample, has shown that adsorption density and zeta potential under some conditions, at least, can be correlated with contact angle and flotation rate. There appear, however, to be several inconsistencies and gaps in information available. One inconsistency involves trying to correlate contact angle with adsorption density on quartz over all pH ranges. Fuerstenau&apos;s correlation at a collector concentration of 4x10-5 moles per liter dodecylamine acetate and about pH 10 shows a contact angle of about 80 degrees occurring at approximately monolayer coverage. If Gaudin and Morrow&apos;s2 and Morrow&apos;s3 contact angle data for near neutrality (pH 6 to 7) are now compared with deBruyn&apos;s4,5 adsorption data on quartz in a similar pH range, it will be noticed that a contact angle of 38 to 40 degrees corresponds to complete monolayer coverage (at an amine concentration of approximately 10"3 molar). In fact even at an amine

Jan 1, 1963

By H. T. Shore, J. M. Schultz

A number of experimental rnethods—X-ray powder diffractometry, Laue photography, X-ray small-angle scattering, and transmission electron microscopy and dijfraction—have been utilized to examine the morphology associated with precipitation from the terminal, g, solid solution of a Zn-1 pct Cu alloy. A significant age hardening was observed in a 1 pct Cu alloy. X-ray and electron diffraction results showed that the structural inhomogeneities associated with the hardening were isotructural with the matrix. The average size and shape of the inhomogeneities were deduced from the electron microscopy and X-ray small-angle scattering. The preprecipitates are hexagonal platelets some 300? in diam. and some twelve unit cells thick. The orientation of the platelets was deduced from Laue photographs and electron diffraction. The platelet plane is (0001). When a large amount of pre-precipitation is present in a localized volume the new lattice is often disoriented by a rotation about (0001) of of the matrix. WhILE dilute Zn-Cu alloys have been commercially important for some 50 years, relatively very little is known metallographically about this material. The "Zilloys", zinc with about 1 wt pct Cu and sometimes a small addition of magnesium, are used to produce rolled zinc which is harder and stronger than that produced by other rollable zinc alloys.&apos; According to the phase diagrams of the zinc-rich side of the Cu-Zn system, such dilute Zn-Cu alloys should age-harden;2-5 the solubility of copper in zinc, g-phase, at 424°C is 2.68 pct, while at 0°C it is only to 0.3 pct. However, the published literature on the aging of this system appears to be limited to a documentation of the contraction of 1, 2, and 3 pct Cu alloys aging at 95°c,6 and an attempt to measure changes in lattice parameters during aging.&apos; In the latter work, no lattice parameter changes were detected, although a broadening of the highest-angle lines was detected and considerable diffuse scattering was observed. Micro-structural investigations have been limited to the latest stage of aging, wherein Widmanstatten precipitates are formed.3,47 These alloys are of interest for still another reason. The two most zinc-rich phases in the Cu-Zn system, 77 and E, are both hcp. Moreover, the change in a, between 17 and t for a 1 wt pct Cu alloy is onlv 3.64 -,~ct: the change in Co is 12.0 ict. It would be anticipated that precipitation in such a material might occur through metastable phases or G.P. zones with epitaxy along mutual 0001 planes. The goals of the present work are aimed at partially filling the void of knowledge concerning the early stages of precipitation from the g phase. In particular, we have attempted to document the magnitude of the age hardening of this system and to determine the size, shape, and orientation within the matrix of the elements of precipitation in an early stage of condensation. EXPERIMENTAL A) Specimen Preparation. Specimens were prepared In two somewhat different ways, one method being used for X-ray Laue and diffractometer measurements, optical microscopy, and Rockwell hardness measurements and the other used for electron microscopy and X-ray small-angle scattering. In the first case zinc and copper in the proper proportions to yield a 1 wt pct Cu alloy were melted together in a closed graphite crucible. Castings so made were free of apparent segregation or oxidation. The castings were then solution-annealed at 400°C for several days and then quenched in water to room temperature. Filings of portions of the specimens were made for use as X-ray powder diffractometry specimens. The electron microscope material was made as follows. Castings were made under vacuum with copper powder placed inside a hollow zinc cylinder to insure good contact of the materials. These 1 wt pct Cu pieces were then rolled to 0.1 mm with an intermediate anneal in vacuo. The rolled sheets so formed were then annealed for about 6 hr at 225°C. Finally the specimens were electropolished slowly until thin enough for transmission electron microscopy. The polishing is discussed in greater detail in the Results section. B) Measurements. X-ray measurements of three types were performed. A G.E. XRD-5 diffractometer was used to examine powders of the alloy for identification of second-phase material. A Kratky small-angle camera, also operating from a G.E. tube, was used to investigate the sizes of small precipitate particles. In both cases, nickel-filtered copper radiation was utilized. Finally, individual grains of the large-grained castings were examined in the back-reflection Laue geometry. Electron microscope studies were carried out with a J.E.O.L. Model 6A instrument. RESULTS A) Hardness Measurements. Hardness measurements performed at room temperature on the large-grained polycrystalline specimens showed a hardening which was essentially complete in 3 hr. Fig. 1 shows a typical plot of hardness vs aging time. The relative magnitude of the ultimate hardening varied from run to run between 150 and 200 pct of the value for the material immediately after quenching from the solution anneal. Most probably the variations reflect small changes in the time taken to remove the specimen from the vacuum furnace after the solution anneal.

Jan 1, 1969

By J. J. Mulligan

Introduction Coal is found in every major geographic region through-out Alaska and in two offshore areas. Since about 1852, more than 100 small mines have opened and closed. In 1981 and 1982 production was almost entirely from one mine in central Alaska. Clearly, the utilization of Alaska&apos;s abundant coal resources presents political, economic, and technical problems that are far from solution. Location and Physical Features Figure 1 illustrates the geographical and geological similarity between Alaska and the western US. Alaska&apos;s Arctic region generally resembles Wyoming and the Dakotas. The Brooks Range is an extension of the Rocky Mountains. The central region of Alaska between the Brooks Range and the Alaska Range bears a general resemblance to the basin and range country of the western US. The southcentral and southeastern regions have a similar resemblance to the Sierra Nevadas and the West Coast. The Arctic, the central, and the southcentral regions have major coal fields. The southeast region has scattered occurrences. The topographic, climatic, and economic characteristics of each are different. These differences have a large effect on practical mining methods. Description of Alaskan Coal Coal deposits known in Alaska are almost all of Cretaceous or Tertiary age, much younger than the Carboniferous coal deposits of eastern and midwestern states. Consequently, most Alaskan coals have a higher moisture content and a lower heat value. Most Alaskan coals also have a much lower sulfur content. Low volatile bituminous, and anthracite coals occur in Alaska, but most Alaskan coals range downward in rank from high volatile bituminous to subbituminous and lignite. Alaskan coals are similar to coals of the northern Great Plains and the Rocky Mountains. Arctic Region Northern Alaska Coal Fields Northern Alaska coal fields are by far the largest group of coal deposits in Alaska (Fig. 2). Coal-bearing rocks extend from the foothills of the Brooks Range about 160 km (100 miles) northward to within about 80 km (50 miles) of the Arctic coast. The principal known occurrences are between the Colville River and the western coast. However, coal has been found eastward almost to the Canning River and westward under the Arctic Ocean. The northern Alaska coal fields are in a series of Cretaceous rocks that suggest a deltaic depositional environment. The beds tend to occur in series of up to eight or nine beds totaling 6-9 m (20-30 ft) of coal. However, beds 6-12 m (20-40 ft) thick have been reported, and beds 1-3 m (3-10 ft) thick seem to be relatively common. Including thin seams, coal in some places makes up about 10% of the stratigraphic section. However, no area has been explored in sufficient detail to block out any large body of reserves or to make reliable estimates of the total resource. Observation points in drill holes and along river and stream banks are few and far between. Coals in northern Alaskan fields tend to range in rank from bituminous, where moderately folded and faulted in the foothills, to subbittuminous in the gently folded rocks under the coastal plain. Coals toward the eastern extremities of the coal fields may be of Tertiary age and lower in rank, but the same general correlation between degree of folding and increase in rank can be expected. Some higher rank coals in the foothills belt are known to have coking properties but most, and possibly all, require

Jan 1, 1984

By W. H. Emmons

THIS paper is the third of a series treating of the relations of ores of the metals to igneous rocks. The first1 outlined the general problem; the second2 proposed a classification of lode ores, and showed how the distribution of the deposits is in a certain measure controlled by the contour of the roof of the parent batholith. A number of mining districts were discussed, the examples being selected chiefly from group 2 of the classification. The proposed classification of lode deposits, briefly stated, is as follows: 1. Cryptobatholithic: near hidden batholiths which have not yet been exhumed by erosion. 2. Acrobatholithic: in and near cupolas or domes of batholiths-the high points of larger underlying masses. 3. Epibatholithic: on batholiths, near their rims, but below eroded cupolas, or below the highest points of the roofs. 4. Embatholithic: among closely-spaced outcrops which probably are parts of a single batholith. The outcrops of invaded rocks predominate. 5. Endobatholithic: in and near roof pendants of large batholiths. The invading rocks predominate. 6. Hypobatholithic: in deeply-eroded batholiths, where even roof pendants, have been -eroded. Deposits of certain metals on the roofs of the batholiths are much more numerous in some positions than deposits of other metals, and the horizontal zonal arrangements of lodes of different metals are shown characteristically only in certain groups. In a large measure, also, the character of the fracturing and metallization is determined by, the-position on the roof, of the batholith.

Jan 1, 1927

By Henry R. Piehler

Continuous seven- and nine teen -filament close-packed silver-steel filamentary composites mere tested in tension. For purposes of comparison, the tensile behavior of the composite was predicted from the measured properties of the individual com-ponents. It was assumed that the axial strain is the same in both components and that the contribution of each component to the composite flow stress is proportional to its volume fraction. Good agreetnent was obtained between the observed and predicted tensile behavior. However, the composite elongation at fracture was about twice that observed when the individual steel wires were tested alone. Composites in which the filaments were widely spaced failed by the consecutive fracture of the filaments. In composites with closely spaced filaments, a composite instability preceded frachcre. These effects are explained in terms of a lateral restraint to the necking of the filaments which develops in the deforming composite. TWO-COMPONENT or composite materials are increasingly being developed and used as structural materials. Of all the composite geometries used, the filamentary configuration has proved to be the most successful. Polymer-bonded fiber-glas, the most common of the filamentary composites, has been investigated most extensively to date. One explanation of the behavior of fiberglas1 suggests that the load transfer between the glass fibers and the polymer matrix occurs primarily through friction. Bond separation between the fibers and the matrix is presumed to occur at very low stresses. Subsequently, only frictional bonding can provide for the transfer of load from the matrix to the fibers. The force normal to the fiber-matrix interface which gives rise to this friction is assumed to arise from the matrix shrinkage which occurs during solidification. The behavior of metallic filamentary-composite materials would be expected to differ from that of fiberglas in several significant aspects. Residual stresses resulting from differences in thermal contraction can be kept to a minimum by proper heat treatment. A strong wetted bond is formed between the two phases. In brazed joints,2 for example, the interphase bond is sufficiently strong that the weaker material will fail before separation occurs at the interface. Most metal filaments can undergo appreciable amounts of plastic deformation before failure. Failure by plastic instability or necking frequently occurs in metallic filaments, but not in glass fibers tested at room temperature. Differences between the behavior of fiberglas-polymer and metallic filamentary composites have indeed been observed in composites containing various types of metallic filaments in a silver matrix.3,4 At strains of the order of 10-2 pct, all the deformation was accommodated by the silver matrix. Hence, the strength of the composite depended only on the fiber concentration and not on the nature of the fiber. At higher strains, the strength of the composite increased when filaments with higher work-hardening rates were used. Surface slip line observations on a silver-mild steel composite that had been stretched 4 pct showed that an appreciable amount of deformation occurred in the filaments. Work on tungsten-copper filamentary composites5 has shown that the ultimate tensile strength for varying filament fractions followed a linear mixture rule. Assuming that the axial strains in both filaments and the matrix are equal, this linear mixture rule can be expressed as: The subscripts c, f, and m refer to the composite, filaments, and matrix, respectively. A and V are the area and volume fractions of each component. sc and of are the ultimate tensile strengths of the composite and the filaments. sm is the flow stress of matrix at a strain equal to the elongation at failure of the filaments. However, the tungsten filaments can undergo only a limited elongation before they fracture without an appreciable reduction in area. A composite containing more ductile filaments might indeed deviate from this linear mixture rule for the ultimate tensile strength, since filament failure by necking might be arrested by the matrix. SPECIMEN PREPARATION Specimens were prepared from 0.8 pct carbon steel piano wires of 0.015 in. initial diameter. The wires were given a thin nickel flash and a silver plate varying in thickness from 0.015 to 0.007 in., depending on the filament fraction desired. In order

Jan 1, 1965

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years&apos; employ¬ment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, how¬ever, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. -Senior Members: The Directors may in their discretion place on the Honor Roll of Senior Members and transfer from any other class of membership other than Honorary Membership the name of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, and for good reasons in special cases may vary the age or number of years. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than 33 years of age at the time of election. SEC. 6. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life member¬ships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute, availing himself of the privilege within ninety days after mailing of notice to him, by the Secretary of the Institute. SEC. 8. Junior Foreign Afliate: Upon appropriate action by the Board of Direc¬tors and with its approval, members in good standing of any technical society having its headquarters outside of the United States of America, Canada, or Mexico,

Jan 1, 1937

By E. O. Wagner, V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pct natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pct of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 1/16 in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F. The necessary heat also can be obtained from 7.5 to 11 cu ft of gas at 2000°F. A description of the design and operation of a pilot plant for flash drying coal dusts is presented. This plant dries 1/16 in. by 0 coal dust in suspension in 1.5 to 2 sec with 600°F gas at a rate of 1300 lb per hour per square foot of column area and operates continuously at an efficiency of about 85 pct. The design and operation of another pilot plant for drying 1/8 in. by 0 coal dusts Is also described. This unit dries coal in the fluidized state using the sensible heat of gases introduced at 2000°F and processes coal at a rate of about 1500 Ib per hour per square foot of grate area at 85 to 90 pct efficiency. Over 90 pct of the bed moisture of low-rank coal dusts can be removed by the methods described. The heating value of lignite can be increased 45 pet and that if subbituminous coal 25 pct in a few seconds. The physical and chemical properties of coal dusts before and after drying are presented in the report, and it is shown that the bulk density of the dried coal is equal to that of the raw coal. This phenomenon makes it possible to ship 25 to 45 pct more heat in a railroad car with consequent savings in freight costs. Introduction For several years the Subbituminous Coal and Lignite Section of the Coal Branch of the Bureau of Mines at Golden, Colo., has been concerned with upgrading low-rank coals by removal of natural bed moisture. These fuels contain 10 to 50 pct total moisture, which reduces their industrial value considerably. In 1938, investigations were initiated in cooperation with the University of North Dakota to study drying of lignite by the Fleissner process with heat derived from high-pressure saturated steam. Two pilot plants were built, and two reports were published giving the results of this work.l,2 It was demonstrated that lump lignite and subbituminous coal

Jan 1, 1950