Search Documents

By Nicholas J. Grant, Bill C. Giessen

The phase diagram Ta-Ni has been treated repeatedly; investigations up to 1958 are summed up in Ref. 1. Since then, an equilibrium diagram has been presented by Kornilov and Pylaeva.2 They found the following intermediate phases: Ta2N; (CuA12 type),3 "TaNi" (p phase, Mo8Co7 type), TaNiz, and TaNi3 (Ticus type).5 Of these, the crystal structure of TaNin remained unknown, and no further literature reference was found. According to Kornilov and pylaeva,&apos; TaNil melts peri-tectically at 1420°C. A 5-g alloy of Ta + 66.7 at. pct Ni was prepared by inert-gas arc melting using 99.95 pct Ta rod (NRC-MG) and 99.9 pct Ni shot (Fisher). The weight loss after three melts was <2 mg; a microscopically homogeneous ingot resulted. As shown in Ref. 6, no oxygen or impurity pickup needed to be considered under these conditions. Specimens were annealed for 15 hr at 1350°C, 15 hr at 1205oC, and 15 hr at 875°C with subsequent powdering and stress relief for 10 min at 1350°C, 15 min at 1205oC, and 1 hr at 875oC, respectively. Micrographs and X-ray analysis (114.6 mm Norelco camera, filtered CuK, radiation) showed homogeneous one-phase alloys in the as-cast state and at all three temperatures, all having the same powder pattern except for broad lines in the as-cast state. From this it is concluded that either TaNi, melts congruently or its melting behavior is a transition between the eutectic and peritectic cases. Since it was found that very slight surface contamination on stress relieving can considerably alter the structure of similar phases (e.g.,TaPt3),7 patterns before and after stress relief were also compared; they were identical except for line broadening in the non-stressrelieved condition, and two faint impurity lines in the stress-relieved samples. The powder pattern is presented in Table I. All lines were accounted for by indexing with a tetragonal lattice, 0Yh- I4/mmm , with a, = 3.154 ± 0.001A, co = 7.905 * 0.002i and c/a = 2.506. The atomic positions are: 1000; 1/2, 1/2, 1/2] + 2Ta(a): 000; + 4Ni(e): *(002); z = 0.333 * 0.002 This proves TaNi2 to be a representative of the MoSiz (Cllb) type. The variable parameter was determined by grouping the visually estimated intensi- ties according to their 2 indices, plotting their F values, and varying z for best fit, which was obtained at z = 0.333= 1/3. Since absorption was not considered, only the relative intensities with similar 28 can be expected to agree. The interatomic distances are presented in Table 11; the standard error is *o.o2A, resulting chiefly from the uncertainty in z. These distances indicate a coordination number 10 for both kinds of atoms and show that the pseudohexagonal layers along (110) are rather un-distorted. The mean atomic volume of 13.1A3 is close to the Vegard&apos;s law value of 13.3A3, showing

Jan 1, 1964

By D. T. Peterson, T. Carnahan

The diffusion coejTicients of carbon, nitrogen, and oxyget were determined in $ thorium over the tempernilcre range 1440" io 1715°C. The diffusion coyfiicir?zls are given by: D = 0.022 exp (-27,000/RT) jor carbo)~, D = 0,0032 exp(-l7,00Q/RTj for nitrogen, and D = u.0013 expt(-11,UOU/RT) for oxygen. Cavl~orz was found to increase the hardness of thoriunz nearly linearly with concentration over the range 100 to 1000Ppm carbon. ThORIUM has a fcc structure up to 1365°C and a bcc structure from this temperature to its melting point at 1740°C. Diffusion of carbon, oxygen, and nitrogen in bcc thorium was of interest in connection with the purification of thorium by electrotransport.&apos; In addition, it was possible to measure the diffusion of all three of these interstitial solutes in the same bcc metal. Only in niobium, tantalum, vanadium, and a iron have all three interstitial diffusion coefficients been measured in a given bcc metal. Diffusion coefficients have been measured for carbon and oxygen in a thorium by Peterson2, 3 and for nitrogen by Gerds and Mallett.4 Activation energies for diffusion are reported by the above authors to be 38 kcal per mole for carbon, 22.5 kcal per mole for nitrogen, and 49 kcal per mole for oxygen. Values of the diffusion coefficients of carbon and nitrogen in 3 thorium have been reported by Peterson et al.&apos; However, these were secondary results of their investigation of electrotransport phenomena in thorium and it was hoped that the present study could provide more precise data. EXPERIMENTAL PROCEDURE The specimens used in this study were the well-known pair of semi-infinite bar type. The couple was formed by resistance butt welding two 0.54-cm-diam by 3.0-cm-long bars of thorium together under pure helium, the concentration of the solute being greater in one cylinder than that in the other. The finished couple then contained a concentration step at the weld interface and diffusion proceeded only along the axis of the rod. The thorium used in this study was prepared by the magnesium intermediate alloy method.5 The total impurity content was less than 400 ppm. The major impurities were: carbon, 100 ppm: nitrogen, 50 ppm; and oxygen. 85 ppm. The total metallic impurity content was less than 150 ppm. The high solute concentration portions of the diffusion couples were prepared by adding the solute to the high-purity thorium in a non-consumable electrode arc melting procedure. Carbon and nitrogen were added in the form of spectroscopic graphite and nitrogen gas while a Tho2 layer was dissolved by arc melting to add oxygen. High-purity thorium formed the low concentration portions in the carbon and nitrogen couples. The low oxygen portions were obtained by deoxidizing high-purity thorium with calcium for 3 weeks at 1000°C according to a method reported by Peterson.3 The high C-Th contained 400 ppm C, the high N-Th contained 400 ppm N, the high 0-Th contained 220 ppm 0, and the low 0-Th contained 25 ppm O. The high O-Th was brine-quenched from 1500°C to retain most of the oxygen in solution at room temperature. These concentration levels were all below the solubility limits in 0 thorium at 1400°C. A resistance-heated high-vacuum furnace was used to heat the couples. The samples were mounted horizontally on a tantalum support which had small grooves near each end. Spacer rods of thorium, 0.4 cm in diam, were placed in these grooves to prevent contact between the sample and the tantalum support. This arrangement should have prevented contamination of the sample by contact with the support. In further effort to reduce contamination, the oxygen diffusion couples were sealed inside evacuated outgassed tantalum cylinders lined with thorium foil. Thorium rings around each end of the samples acted as spacers in this case. Pressure during diffusion runs was about 10-6 torr after an initial outgassing stage. Temperature measurements were made by sighting on black body holes in the sample support adjacent to the samples with a Leeds and Northrup disappearing-filament optical pyrometer. Temperatures were constant during a diffusion anneal to ±5C. The observed temperatures were corrected for sight glass absorption after each diffusion run. The pyrometer was checked against a calibrated electronic optical pyrometer and a calibrated tungsten strip lamp with the electronic pyrometer being taken as the standard. All temperature readings agreed to within ±3C over the temperature range 1450" to 1690°C. Time corrections due to diffusion during heating and cooling were necessary because of the short diffusion times. The diffusion times ranged from 6 min for the oxygen sample run at 1690°C to 90 min for the carbon sample run at 1500°C. A series of temperature vs time plots were made for heating and cooling of the samples to the various diffusion temperatures. This data was then used in a method according to shewmon6 to determine the time corrections. The corrections amounted to

Jan 1, 1970

By Babbitts and Solder

G. w. Thompson,* Brooklyn, N. Y.—This subject has two aspects, neither of which can be ignored: these are the economic aspect and the technical aspect. Under ordinary conditions, economic law will take care of the conservation of tin. Under present conditions it seems desirable that economic law should still be permitted to operate as far as is practicable. It is true that this law operates rather slowly, and that under war conditions it cannot be depended upon to give our Government the supply it immediately needs. There should, therefore, be a designation of the essential industries by the Government, and tin should be supplied for those needs, letting the non-essential industries take what is left. At the same time, information ought to be forthcoming as to how tin can be conserved; with tin selling at 80 c. per pound, more or less, it is to the interest of every consumer to get the best information he can as to how he can save tin. Economic law would properly punish those who do not study their own interests in this way. I deprecate, therefore, any centralized socialistic effort toward avoiding penalties through failure to observe and obey economic law. In saying this, however, I am not unmindful that it is desirable for our Government to take such control of the tin situation as may be necessary to the prosecution of the war, practically regardless of the effect of such action upon individual industry, which should studiously seek to adjust itself to the new condition. The Government should promulgate such technical information as it can collect, showing how .tin can be conserved, and should urge upon every consumer the exercise of his common sense in self-protection. There is very little danger of any one attempting to hoard or corner tin, in the present state of the market. Most consumers will be glad to live from hand to mouth, covering their sales by purchases, or vice versa. As to the technical aspects: Tin and tin alloys are used to give certain practical and also certain artistic results. The practical factors are those involved in proper adhesion, continuity of surface, protection, the right degree of hardness, proper working qualities, etc. The artistic results are those that appeal purely to the eye or to our cultivated sense of what is desirable. There is no doubt that a great deal of tin could be saved if there were not a demand for certain pleasing effects. Row can this saving be brought about? The users of tin bearing alloys are not the only ones involved in this question. The manufacturers of solder and babbitt have for a long time sought to give certain appearances to their fabricated bars and ingots in order to make them more salable. The user of a solder is very apt to judge of its working qualities by the appearance of the bar; the same thing is true with regard to babbitts. Under ordinary conditions, manufacturers are justified in trying to

Jan 1, 1919

By M. K. Yen, W. R. Hibbard

Previous studies of plastic deformation of metals have emphasized the important role of bending and constraints during strain under relatively pure stresses.1"5 Some new phenomena such as early conjugate slip6 and polygonization7 are intimately concerned with the relief of bending stresses, the former by slip and the latter by a process analogous to re-crystallization. However, few analyses of the bending deformation of single crystals were found in the literature, and those8,9 are sufficiently previous to the modern interpretations of slip to invite further investigation in this area. The transverse bending mode of testing, using the two-point loading method, was selected because the center portion of the specimen may be considered as under a theoretically pure bending stress with a uniform bending moment. Considerable attention was given to both the lattice distortion and flow characteristics of the crystals during deformation. Experimental Proeedare A specimen under the action of equal and opposite couples at both ends is said to undergo pure bending. The shear and moment diagrams of a specimen under the two-point loading method of transverse bending are shown in Fig 1. The moment over the middle-third of the span is equal to PL/6, and the vertical shear is zero. Fig 2 (A) illustrates the stress distribution in the elastic range on a plane across the middle of the specimen. It can be seen that the normal stress has a maximum value at the extreme surfaces on the tension and compression sides, and decreases proportionately to zero as it approaches the neutral plane. However, when the plastic range is reached, the stress distribution is no longer a straight line relation, but changes in a manner which can be best illustrated as shown in Fig 2(B). The following calculation and stress analysis are mainly in accordance with the works reported by Timoshenkol0 and Kochendörfer.9 From the simple beam formula, the maximum normal stress will occur at the surface of the specimen. For a round specimen with a radius r and for a rectangular specimen with a height 2h and width 2b, the maximum normal stress, Sp, will be given by the following formulas: For round specimen: 2PL Sp = 3pr3 [1] For rectangular specimen: Sn = 8bh2 [2] Since it is reasonable to consider that slip takes place under the same conditions as in uniaxial loading, the resolved shear stress S?, along the operative slip direction will be as follows: For round specimen: 2PL sin x cos ? Sp = 3pr3 sin x cos ? [3] For rectangular specimen: PL S8 = 8bh2 sin x cos ? [4] where X is the angle between the specimen axis and the slip direction and X, the angle between the specimen axis and the major axis of the glide ellipse. It was also reported by Kochenclorfer9 that the critical bending moment, that is, the bending moment exerted on the specimen to initiate slip, should be higher than the value given by the equations stated above. Based

Jan 1, 1950

By C. M. Fellman

AVAILABLE data for the first nine months of the Year indicate that accident occurrence in metal mining was well on its way to an all-time low for 1939. However, the relatively rapid pickup in mining production in the fall will be likely to boost both accident occurrence and also accident rates. Results of the National Safety Competition for 1938, the fourteenth of its kind conducted by the U. S. Bureau of Mines, were published in August, 1939. W. W. Adams, statistician of the bureau, states that "with 345 mines and quarries competing, more than in any previous year except 1931, the contest revealed low accident rates at many of the enrolled plants and, which is even more remarkable, it revealed 113 mines and quarries at which no lost- time accidents occurred during the con- test year." The National Safety Competition provides a means whereby mines and quarries may engage in active competition to stimulate their safety programs. Companies in the contest can compare their records with those of similar plants operating elsewhere and thereby determine to what extent their safety programs are successful. The Joseph A. Holmes Safety Association gave over 150 awards for safety performance in the mineral industries in 1939 and a remarkable phase of these awards was the considerable number given to individual miners who had worked fifty or more years without sustaining a lost-time accident.

Jan 1, 1940

By Joseph L. Gillson

Bentonite, designating a distinct type of clay, is a young name in mineral nomenclature in the light of the age-old names of most other useful nonmetallics. The earliest references in literature are to "soap clay" (1873) "taylorite" (1888) and finally "bentonite" in 1897, from its occurrence in the Fort Benton series of rocks near Rock Creek, Albany County, Wyoming. Bentonite is a rock term and consists largely of montmorillonite clay. The latter name was proposed in 1847 for a plastic clay found at Montmorillon, France. A clay of apparently identical properties was described by Cronstedt of Sweden in 1788 and a number of other similar clays found in France were given other names in publications from 1853 to 1856. The mineral name montmorillonite was recognized by Dana in 1892. The recognition of "clay mineral" distinctions which led to the present-day classifications of clays by their chief mineral content, dawned in the early part of the twentieth century. Grim6 has aptly said: About 1924, Ross10 and some colleagues of the U. S. Geological Survey began a study of the mineral composition of clays that led to a series of monumental papers on the subject. By the early 1930&apos;s what has come to be known as the clay-mineral concept became firmly established in the minds of a great many people actively studying clay materials. The clay mineral concept designates the major clays as kaolins, montmorillonites and illites and by this concept bentonites are now defined as "fine-grained clays containing not less than 85 pct montmorillonite" and a wide variety of clays found all over the world are included in that classification. They could all properly be called "montmorillonite clays" but the common commercial name is bentonite. For a period of over forty years from the time of the earlier discoveries, bentonite was thought to be only the sodium type highswelling clay produced principally in Wyoming. By the clay mineral concept, non-swelling montmorillonite clays also became known as bentonite. In the trade there are two broad divisions-sodium bentonite, often called Wyoming or "western," which expands in water and carries sodium as its predominant exchangeable ion, and calcium bentonite often called "southern," which has negligible swelling and carries calcium as its principal exchangeable ion. There are many intermediate gradations. Properties The mineralogy and chemistry of the clays are so complex that the subject cannot be summarized briefly. The reader is referred to Chapter 12 of this volume in which the subject is treated at some length. Grim6 gave the formula for montmorillonite as (OH)4Si8AL4020.nH2O. He wrote: Montmorillonite is composed of units made up of two silica tetrahedral sheets with a central alumina octahedral sheet. . . . Exchangeable rations occur between the silicate layers. . . . The words "tetrahedral" and "octahedral" refer to the coordination number of the cations in the unit cell in the crystallographic lattice. Carroll5a stated: That the montmorillonite structure is the same as that of mica, but the layers are not held together by K+ ions; and water and other polar molecules, such as organic molecules, can enter between the unit layers and cause expansion. Ex-

Jan 1, 1960

By G. W. Thompson

G. W. THOMPSON,* Brooklyn, N. Y.-This subject has two aspects, neither of-which can be ignored: these are the economic aspect and the technical aspect. Under ordinary conditions, economic law will take care of the conservation of tin. Under present conditions it seems desirable that economic law should still be permitted to operate as far as is practicable. It is true that this law operates rather slowly, and that under war conditions it cannot be depended upon to give our Government the supply it immediately needs. There should, therefore, be a designation of the essential industries by the Government, and tin should be supplied for those needs, letting the non-essential industries take what is left. At the same time, information ought to be forthcoming as to how tin can be conserved; with tin selling at 80 c. per pound, more or less, it is to the interest of every consumer to get the best information he can as to how he can save tin. Economic law would properly punish those who do not study their own interests in this way. I deprecate, therefore, any centralized socialistic effort toward avoiding penalties through failure to observe and obey economic law. In saying this, however, I am not unmindful that it is desirable for our Government to take such control of the tin situation as may be necessary to the prosecution of the war, practically regardless of the effect of such action upon individual industry, which should studiously seek to adjust itself to the new condition. The Government should promulgate such technical information as it can collect, showing how tin can be conserved, and should urge upon every consumer the exercise of his common sense in self-protection. There is very little danger of any one attempting to hoard or corner tin, in the present state of the market. Most consumers will be glad to live from hand to mouth, covering their sales by purchases, or vice versa. As to the technical aspects: Tin and tin alloys are used to give certain practical and also certain artistic results. The practical factors are those involved in proper adhesion, continuity of surface, protection, the right degree of hardness, proper working qualities, etc. The artistic results are those that appeal purely to the eye or to our cultivated sense of what is desirable. There is no doubt that a great deal of tin could be saved if there were not a demand for certain pleasing effects. How can this saving be brought about? The users of tin hearing alloys are not the only ones involved in this question. The manufacturers of solder and babbitt have for a long time sought to give certain appearances to their fabricated bars and ingots in order to make them more salable. The user of a solder is very apt to judge of its working qualities by the appearance of the bar; the same thing is true with regard to babbitts. Under ordinary conditions, manufacturers are justified in trying to

Jan 12, 1918

By Ralph M. Roosevelt

IN AS MUCH as our Institute, by tradition, never adopts any official view of matters upon which difference of opinion exists, it may be taken for granted that the duty of its Production Control Committee does&apos; not embrace the formulation of any general policy on that much-discussed subject. During the first years of its existence the Committee confined its activities to making arrangements for an annual general session at which the broader aspects of the general problem were discussed by men both within and outside the mineral industry. These general sessions, although interesting, did not indicate any definite path of progress, so during the last year the Committee has held a number of luncheon meetings at which the members might discuss in detail problems existing in the specific industries with which they are most closely acquainted, in the hope that discussions dealing with conditions rather than theories might result in the bringing to light of some general truths. Most of these truths have been fairly obvious from the beginning but they are of such basic importance that a periodic restatement of them seems worth while,

Jan 1, 1932

By Wilbur H. Somerton

In order to evaluate the quantitative determination of porosity by various neutron logging systems, four test wells were constructed to simulate some of the possible variab1e.r found in field logging conditions. All of the test holes contain sections of limestone with one section of sandstone included in one well. Each well has a representative section of high, medium, and low porosity. Three borehole sizes are represented by three of the test wells, all containing fresh water. One test well contains saturated brine. Statistical and tune constant checks are made for each system evaluated. Runs and repeat runs are made with the sonde centered and eccentric. Factors evaluated are the effect of borehole size, sonde position, salinity, chemical composition of rock, and statistical variation. A semi-quantitative method of evaluation of these effects is used giving the average maximum per cent error possible for each. Drift and calibration procedures are also discussed. The effect of the various factors appears to be largely a function of the phenomena detected as well as the means of detection. Graphic illustrations of some of these effects are presented. It is concluded, that for accurate log interpretation, the hole size and sonde position should be known. INTRODUCTION The use of neutron logs for the derivation of porosity has become an accepted practice in many areas. In recent years, many different neutron logging systems have been offered to the industry. The neutron sources presently available are of the radium-beryllium or polonium -beryllium type. Detector types used are ionization chambers, Geiger-Mueller-type counters, proportional counters, or scintillation detectors used to detect or measure gamma rays, thermal neutrons, epithermal neutrons, fast neutrons or combinations of these. It is well-known that all systems do not respond alike in all environments. As a result, testing facilities and an evaluation method were developed for use in evaluating the porosity discriminating ability of neutron logging systems using conditions simulating those normally encountered in the field. With such an evaluation, the suitability of a logging system can be determined lor selected field conditions. TEST FACILITIES The testing facilities consist of wells containing rocks of various porosities, constructed to include as many parameters as practicable. Three pits were drilled to a depth of 20 ft and the fourth to a depth of 9 ft, all having 48-in. diameters. Rat holes were dug to a depth of 6 ft in the center of each pit and fitted with sections of pipe having appropriate diameters. The top of this pipe was located approximately 8 in. above the pit bottom. A 6-in, layer of cement was then poured on the bottom and while still wet, 42-in. OD corrugated, galvanized culvert pipe was set on bottom and centered in place. This pipe extends approximately 1 ft above the surface of the ground. The annulus around the culvert pipe was then filled with cement to the top. A 1- or 2-in. layer of sand was placed on the cement bottom to provide an adjustable bed on which to place the series of rocks set in each hole. A cross section of a typical test well containing the porous rocks is shown in Fig. 1.

By J. W. Edington

THE Hopkinson bar has become a popular technique for the measurement of the mechanical properties of materials deformed at high strain rate. Maximum use of the equipment is made in the arrangement first used by Kolskyl in which a short compression specimen is sandwiched between two pressure bars and is loaded by a single pulse travelling through the system. The pressure bars are used both to apply the load to the specimen and as transducers to obtain continuous strain-time histories of three pulses, incident on, reflected, and transmitted by the specimen. The data measured by the pressure bars can be analyzed in terms of the stress/strain behavior of the specimen.2&apos;3 However, one of the assumptions of the analysis of the observed pulses is that the total stress and total strain do not vary significantly from point to point within the specimen at any given instant during the deformation process. Although this assumption is generally justified for very short disc-like specimens2 the situation is uncertain for larger specimens. For example, at small plastic strains (-0.01) Hauser et al.2 have some evidence of small flucations in the total stress within the crystal during deformation, even in relatively short aluminum specimens. In addition, Karnes4 has shown that the plastic strain, and by inference strain rate, is different at each end of a compression specimen tested in a Hopkinson bar, although the length of the specimen was not specified. Recently, the mechanical properties and the dislocation substructure have been investigated in single crystals of columbium5 (length 0.25 in., diam 0.19 in.), and copper6 (length 0.5 in., diam 0.5 in.) deformed at high strain rates. As part of this research program the assumption that the plastic strain is constant throughout the specimen has been checked by measuring the total dislocation density as a function of position in the specimen. Compression specimens of the same orientations and dimensions were tested as described previously5,6 sing a split Hopkinson bar. Since any discontinuity in strain distribution is most likely to arise during the initial stages of deformation the investigation was performed on specimens deformed to plastic shear strains of 0.054 (copper) at a strain rate 1.2 x l03 sec-1, and 0.06 (columbium) at a strain rate 1.5 X l03 sec-1. The orientation of the single crystals is shown in Figs. 1 and 3. Thin foils were taken parallel to the most highly stressed slip plane, i.e., (111) in copper and (011) in columbium, using conventional disc techniques. The dislocation densities were measured using first order reflections with compensation for invisible dislocations.5&apos;6 In the copper single crystals the discs were randomly distributed throughout the cross section of the specimen. However, the dislocation density obtained from each disc was plotted vs the disc positions relative to the ends of the specimen. The results for the copper specimens are shown in Fig. 1. Clearly the dislocation density is constant throughout the main portion of specimen within the experimental error. The error bars on the dislocation densities correspond to a shear strain variation of 0.015 on the basis of previous measurements% ± of the rate of increase of dislocation density with strain in copper single crystals of the same geometry. Thus within this experimental error the plastic strain can be concluded to be constant within the specimen and the assumptions used in the analysis of the stress/time curves are therefore reasonably valid. The higher measured dslocation density near the impact end and the lower dislocation density at the bar end of the copper specimen is in agreement with the results of Karnes4 who showed that this strain/time curve rose to a maximum more rapidly at the impact end compared with the bar end. Hauser et al.2 have also pointed out that at small plastic strains (-0.01) the strain at the impact end of the specimen may be greater than that at the bar end. Thin foils taken from different points within the columbium single crystals demonstrated that the dislocation density could vary significantly within the specimen, see Fig. 2. Large areas of some thin foils up to 30 µ sq contained very few dislocations, see Fig. 2(a). However, in other parts of the compression specimen dislocation configurations like those shown in Fig. 2(b) existed over large areas (-30 µ sq). As a result, when the average dislocation density in a thin foil is plotted as a function of the position of the thin foil relative to the ends of the specimen, considerable scatter is observed, see Fig. 3. In this material then, the local dislocation density, and consequently the

Jan 1, 1970

By Joseph R. Stephens

Deformation substructures of&apos; polycrystalline tungsten, W-2, 9, and 24 pct Re, and W-3 pct Ta were studied by tra?zsrnission electron microscopy. The stress-strain curve for unalloyed tungsten showed gradual yielding followed by work-hardening. Electron nzicrographs indicated a gradual increase in dislocation density with increase in strain up to 5.0 pct. Dislocations, although frequently jogged, were straight over moderate distances and were in a randorn array. Stress-strain curves for alloy specimens of W-2 and 9 pct Re and W-3 pct Ta exhibited a drop in stress at yielding followed by only slight work-hardening. Electron micrographs of these specimens after strains of 0.05, 0.1, and 0.5 pct revealed no change in dislocation substructure from the unstrained specimens. After 2.0 pct strain, the three alloys exhibited dense networks. W-3 pct Ta was characterized by straight, frequently jogged dislocations comparable with the dislocation structure in unalloyed tungsten after a similar amount of strain. In contrast, W-2 pct Re exhibited dislocations that contained widely spaced jogs, while W-9 pct Re had developed a cell structure after the relatively srnall strain of 2.0 pct. The W-24 pct Re alloy contained a few dislocations after 0.1 pct strain, while after 0.5 pct strain twins were evident. Dislocation slip bands apparently preceded the twins. The stress-strain curve for the alloy indicated that twinning commenced after approximately 0.25 pet strain. These results indicate that the primary effect of low rhenium concentrations (2 and 9 pct) in tungsten is to increase dislocation multiplication after macroyielding by reducing the Peierls-Nabarro force (lattice resistance to dislocation motion). The dislocation bands that precede twins in W-24 pct Re may be caused by localized internal stresses resulting fro a metastable structure, for example, clustering of rhenium atoms. The effect of high rhenium additions (22 a 65 pet* Rproperties of tungsten. Klopp, Witzke, and Raffo5 reported bend transition temperatures as low as -100°F (200°K) for dilute electron-beam-melted W-Re alloys tested in the worked condition. Recrystalliza-tion increased the bend transition temperature, but alloys with 2 to 4 pct Re were still markedly superior to unalloyed tungsten. Fractographic examinations of tungsten and W- 3 pct Re and W- 5 pct Re alloys by Gilbert 6 revealed that these low rhenium alloys showed a greater tendency toward cleavage failure than did tungsten. Garfinkle 7 showed that rhenium additions, up to 9 pct, to (100) oriented tungsten single crystals increased the proportional limit stress and decreased the flow stress and the rate of work-hardening. In addition, while deformation in unalloyed (100) oriented crystals apparently involved both (110)100) and (112) slip, crystals with rhenium contents of 5 andpct or more deformed primarily by (112) slip. The mechanism by which high and low rhenium additions affect the mechanical properties of tungsten is still not well-established. The present investigation was undertaken to determine by transmission electron microscopy the effects of low rhenium additions, 2 and 9 pct, and a high rhenium addition, 24 pct, on dislocation substructure in the early stages of deformation of polycrystalline electron-beam-melted tungsten. Unalloyed tungsten and a W- 3 pct Ta alloy were included for comparison. EXPERIMENTAL PROCEDURES Materials. Triple electron-beam-melted tungsten, W-2, 9, and 24 pct Re, and W- pet Ta were used for this investigation. Chemical analyses of the cast ingots are given in Table I. A description of the starting metal powders and melting and fabrication pro-cedures for unalloyed tungsten and the W-Re alloys is reported.5 The W-3 pet Ta alloy was processed in a similar manner. Compression specimens measuring 0.300 in. (7.6 mm) in length by 0.130 in. (3.3 mm) in diam were machined from swaged rods. All alloy specimens were annealed in a vacuum of 8 x 10- 6 Torr (10&apos;2iVper sq m) for 1 hr at 3600°F (2255°K). The recrystallized grain size ranged from 0.06 to 0.08 mm diam for the alloy specimens. Unalloyed tungsten was annealed at 2400° F (1589°K) for 1 hr to produce a recrystallized grain diameter of approximately 0.12 mm. Specimens were electropolished in a 2 pet NaOH solution to a diameter of 0.125 in. (3.18 mm) to remove surface notches resulting from grinding and to improve reproducibility of t data. The ends o the compression specimens were ground flat, parallel to each other, and perpendicular to the longitudinal axes with 4/0 emery paper. Compression Tests. The compressive stress-strain apparatus used for compression tests is described in detail by Stearns and Gotsky.9 Room-temperature compression tests were conducted at a crosshead speed of 0.01 in. per min (0.25 mm per min).

Jan 1, 1969

By J. R. Cahoon, H. W. Paxton

The possibility of using unidirectionally solidified, two-phase alloys as an approximation to fiber composite materials is investigated. The short-term me.chanical properties and failure modes of unidirectionully solidified A1 (rich)-Cu alloys containing ap -Proximately 0, 17.5, and 27.7 vol pct of 0 phase &apos;fibers" are determined at temperatures from 25" to 500" and compared with those obtained for conventionul SAP alloys. In a previous publication,&apos; hereafter referred to as I, the possibility of understanding some of the room-temperature mechanical properties of unidirectionally solidified castings was explored. For Al(rich)-Cu and Al(rich)-Mg two-phase alloys over a substantial range of compositions, the yield and ultimate strengths and common ductility measures were very adequately predicted from the principles of fiber strengthening4 and the analysis of ductility outlined by Gurland and Plateau." The results obtained in I suggest the possibility of using unidirectionally solidified, two-phase alloys to simulate fiber composite materials where the inter-dendritic second phase or constituent acts as the reinforcing material. Recent attempts concerning the fabrication of fiber conlposites have concentrated on producing composites with a good bond between fiber and matrix and with very long fibers so that their maximum contribution to the strength of the composite may be realized. However, these objectives are difficult to attain in practice and present fabrication processes are either extremely laborious or costly.13 The slow, unidirectional solidification of eutectics has received considerable attention as a method for producing composite materials. 5,6 This method can fulfill both of the above objectives but it is currently laborious, expensive, and has the additional disadvantage that the volume fraction of reinforcing phase cannot be easily varied. On the other hand, unidirectionally solidified, two-phase alloys, also with a good bond between the phases, are relatively easy to make and the volume fraction of reinforcing "fibers" can be easily varied by changing the average composition of the alloy. The disadvantage of the cast alloys is that the mechanical effectiveness of the "elongated interdendritic reinforcements" (EIR)* may be reduced due to their rela- tively short lengths, the w factor in Eq. [2] of I. However, if the EIR have a high strength their contribution can be considerable. For composite materials containing discontinuous cylindrical fibers of various lengths the ultimate strength is given by1 where it is assumed that the composite fractures when the fibers fail. In Eq. [I], a, is the stress in the matrix just prior to failure of the composite, Vf is the total volume fraction of fiber reinforcing constituent, Vf(l+) is the volume fraction of fibers whose lengths exceed the critical length, I,, which is defined as the shortest length of fiber in which the stress can build up sufficiently to break the fiber. af is the fracture strength of the fiber material, w is a factor accounting for the discontinuity of those fibers whose lengths exceed I,, 1-/d is the average aspect ratio of those fibers whose lengths are shorter than I,, and t is the shear stress in the matrix at the fiber-matrix interface. The factor w is dependent on the length of the fibers and also on whether deformation of the matrix occurs plastically or elastically. However, for a given length of fiber, w is smaller when elastic deformation of the matrix is assumed.&apos; It is of interest to consider the properties of simple unidirectionally solidified, two-phase alloys at elevated temperatures in view of the possibility of using suitable modifications for high temperature service. Knowledge of the creep behavior of these materials is still rudimentary (although under active investigation) and the present paper concerns itself with short time tensile properties of some alloys similar to those investigated in I (i.e., unidirectionally solidified Al(rich)-Cu alloys). Unidirectionally solidified alloys containing 5.6, 17, and 23 wt pct Cu were tested parallel to the direction of solidification at temperatures from 25" to 500°C. In the present investigation, the alloys were homogenized for 2 days at 535°C giving a matrix of homogeneous a phase (5.2 wt pct Cu) and an interdendritic constituent (EIR) which was completely Q phase (53 wt pct Cu). EXPERIMENTAL Alloys of nominal composition 5.6, 17, and 23 wt pct Cu (containing approximately 0, 17.5, and 27.7 vol pct 8 phase, respectively, after homogenization at 535°C) were prepared by melting 1200 g of A1 (99.99 pct) in a high purity graphite crucible and adding the appropriate amount of freshly cleaned copper chips (99.9 pct). The molten alloy (at 700°C) was poured into a preheated graphite mold (also at 700°C) and the ingot unidirectionally solidified by impinging water on the steel baseplate of the mold. The alloy was degassed immediately

Jan 1, 1970

By AIME AIME

IN ACCORDANCE with the provisions of the Rules of Procedure of the American Engineering Standards Committee, the American Society for Testing, Mate-. on Feb. 15, 1921, submitted for approval by the A. E. S. Committee certain Standard Specifications for Copper, all of which were adopted or in process prior to Jan. 1, 1920, and sent with the standards the following histories of development and statements of use. FOR SOFT OR ANNEALED COPPER WIRE (B3-15) These specifications were originaly adopted by. the American Society for Testing Materials in 1912. They were prepared by a committee of the Society designated as Committee B-1 on Copper Wire. The committee consisted of eleven members; representatives of five manufacturers of -copper wire, of four manufacturers of electrical apparatus, and of two firms of consulting and contracting engineers. The members of the committee were designated by the officials of the companies to act as their representatives in the committee.

Jan 1, 1921

By James A. Crookston, William D. Fitzpatrick

Committee C-8 of the American Society for Testing and Materials defines refractories as "material, usually nonmetallic, used to withstand high temperature," and it defines the term refractoriness thus, "in refractories, the capability of maintaining the desired degree of chemical and physical identity at high temperatures and in the environment and conditions of use.” The ability to withstand high temperatures is critical to classifying a material as a refractory. However, as the foregoing definition of "refractoriness" implies, the refractory material may be subjected to and is expected to resist not only high temperatures but a variety of other destructive forces incidental to its use. These include abrasion, impact, thermal shock, chemical attack, and high level loads at high temperatures. The various industrial applications of refractories represent an infinite variety of combinations and degrees of severity of these destructive forces, including high temperatures. Naturally, such a variety of application conditions leads to a need for a wide variety of refractory products to satisfy those conditions. The number of refractory products available is great enough that some form of classification is necessary to a discussion of refractories. Refractories may be classified in several ways, but the most suitable one is based on their general compositions and to lesser degrees on their physical condition and distinctive properties. The primary types of brick include aluminosilicate brick (fire clay and alumina), basic brick (magnesia and chrome ore, alone and in various combinations), silica brick, insulating brick, and special refractories (carbon, SiC, ZrO2, zircon, borides, and nitrides). Brick is, of course, preformed and usually is heat treated at high temperatures before use, but in some instances is unburned and/or chemically bonded, including the relatively new class of tar-bonded magnesia and/or dolomite brick. In addition to preformed refractories, another broad category includes the so-called specialty refractories, which are usually made in the same types as itemized for brick-bonding mortars and high temperature cements, hydraulic setting castables or refractory concrete, plastic firebrick, and ramming mixes. Refractory grains, such as fire clay and high alumina calcines, dead-burned magnesite and periclase, and dead-burned dolomite are also considered refractory products. Bricks are also classified on the basis of physical dimensions, as standard sizes and special shapes. The standard sizes are those which are of definite shape and design and are designated as 228.6 x 114.3 x 63.5 mm (9 x 4 ½ x 2 ½ in.) and 228.6 x 114.3 x 76.2 mm (9 x 4 ½ x 3 in.) straights and series. Bricks of nonstandard sizes are referred to as special shapes. These come about as a result of a particular need for a given furnace or for a particular application. Types and Classes of Refractories Fire Clay Refractories Classification: Fire clay refractories, as the name implies, are composed essentially of fire clay and/or calcined fire clay in varying proportions. The ASTM Standard Classification of Fireclay and High Alumina Refractory Brick, C27-70 (reapproved 1976), gives five classes of fire clay brick designated as super-

Jan 1, 1983

By C. E. Morris, S. R. Pollack

Current -vo1tage -temperature characteristics were studied for Al-A12O3-Al, Au structures. The oxide film was grown by gaseous oxidation in an 0, glow discharge. The electron-transfer mechanism was identified as tunneling and the barrier heights and thickness were determined. It was found that the barrier height at the parent aluminum-oxide interface is 1.5 ev and the built-in vloltage with an aluminum counter electrode is 0.35 v. The growth mechanism of the oxide is also discussed and it is suggested that Mott&apos;s theory is not applicable in describing the growth. Discrepancies were observed in the detailed comparison of tunneling theory, based on a trapezoidal model, with the data, and several possible explanations are discussed. THEORETICAL analyses of electron tunneling from one nonsuperconducting metal to another through an extremely thin insulating film have been presented.1-6 These calculations relate the current density, J, to the voltage, V, between the two metals, and to the temperature, T. The results of these calculations indicate that the magnitude of J and the detailed shape of the J-V characteristic will in general depend most strongly upon such properties of the insulating film as the thickness, the dielectric constant, and the structure of the electron energy barrier profile. The experimental results of many7-11 workers have corroborated the main features of these calcu- lations and have in fact been used to determine properties of the thin insulating film. It has been demonstrated, for example, that the tunneling current formulation of simmons4 is adequate to describe the observed J-V characteristic over approximately 10 orders of magnitude of current. Furthermore, from these observations and analyses, insight into the nature of the A1-A12O3 (thermally grown) interface region has been obtained.&apos;&apos; The temperature dependence of the tunnel current has also been studied and, although a self-consistent set of tunneling parameters can be chosen to describe these data at low voltages (i.e., <0.5 v), the tunneling parameters are different from those obtained from higher voltage (i.e., of the order of 1 to 5 v) measurements." We have measured the effect of temperature and voltage upon the tunnel current at higher applied voltages and find that the theory is inadequate to describe all of the effects reported here. A discussion of the origin of this inadequacy is presented following a description of the samples used for these experiments, and the experimental results. SAMPLE PREPARATION Metal-insulator-metal structures were fabricated in the following way. A 99.999 pct A1 charge was used to deposit, in vacuo, thirty films, 2000Å thick, onto a 1 by 2 in. glass substrate (7059 Corning glass). Prior to deposition the substrate was glow-discharged for final cleanup and then baked at 200°C for 2 hr at a pressure of 5 x 10-7 torr. The pressure during deposition of the metal films was 2 X 10-6 torr and the deposition rate was 50 to 100Å per

Jan 1, 1965

By R. H. Richman, F. Borik

A 0.3 pct C-12 pct Cr-6 pct Ni steel was rolled to 93 pct reduclion in area as austenite at 510°C, and then partially transformed as desired to ~rlartensite by qnenching to - 196°C. Pole figures for the austenitic matrix and for the martensitic product were separately determined by an X-ray transmission method. The deforitration texture of&apos; the warm-worked austenite is characlerized by (110)(225) components, and is thus closely similar to those produced in a brasses. The pole jigure of the martensite in partially transformed material agrees well with that which can be constructed by transfortnation of the {110)(225) orientations according to either the Kuvdjuniov- Sacks or the Nishi-yatuu relatiotship. Howeuer, an important result of this construction is that me-third of the predicted orientations are missing. A graphical analysis can then be used to show that in deformed austenite certain crystallographic variants of martensite (related to the most probable austenite slip systems) are suppressed, resulting in this preferred transformation. The evidence for preferred transformation is corroborated by the measured elastic anisotropy of warm-rolled and fully transformed H-11 steel. EXTENSIVE plastic deformation of a polycrystal-line aggregate in a manner that causes flow predominantly in one direction results in a preferred orientation of the constituent crystallites. The particular orientations that are produced depend upon the crystal structure and composition of the material, as well as upon the temperature, mode, and degree of deformation; in any case, the preferred crystallo-graphic orientations, or textures, are reflected in directionality of mechanical properties. Although such anisotropy may be exploited in certain specialized applications, it is more commonly diminished or eliminated by heat treatment lest it interfere undesirably in subsequent forming operations or in structural design. In the recently developed thermomechanical treatments that significantly enhance the strength of some steels,1,2 considerable deformation of the metastable austenite prior to the martensite transformation is essential to the strengthening process. If the austenite is textured by the deformation, and if the transformation to martensite proceeds according to one of the relationships established for transformation in annealed austenite, then it must be expected that the martensite will also possess a preferred orientation even though the multiplicity of martensite orientations possible in a given austen- ite crystal will tend to restore some degree of randomness. The existence of a residual anisotropy, both mechanical 3-6 and crystallographic,&apos; has been substantiated. In the latter crystallographic investigation, preferred orientations were determined for the martensitic structure of an SAE 4340 steel rolled 72 pct as austenite at 833°C and then quenched. However, the choice of a composition that transformed almost completely to martensite during the quench to room temperature did not permit direct measurement of the prior austenitic texture. In fact, when the "ideal orientations&apos;&apos; associated with well-known fcc rolling textures were converted, alone or in combination, to martensite according to the Kur-djumov-Sachs (K-s)&apos; or Nishiyama8 relations, the agreement obtained with the observed martensite texture was only fair at best. Recently a pertinent aspect of the austenite to martensite transformation was reported by Bokros and parker,10 who found that certain habit-plane variants of martensite were suppressed by tensile deformation of Fe-31.7 Ni single crystals prior to the necessary subzero cooling. It might be anticipated that the consequences of such preferred transformation are sustained during the formation of martensite in warm-worked austenite that has a well-developed deformation texture. The present investigation was undertaken first to establish more firmly the relation between preferred orientations in plastically deformed austenite and in the resulting martensite, and second to examine the textures for evidence of deformation-induced preferred transformation. EXPERIMENTAL PROCEDURES An alloy containing 0.3 pct C, 12 pct Cr, 6 pct Ni, and the balance iron, was selected because the mar-tensite-start temperature (M,) of about -100°C allowed convenient experimental manipulation of either austenite or martensite at room temperature. Furthermore, this composition can be readily deformed as metastable austenite at moderately elevated temperatures without intervention of appreciable isothermal or athermal decomposition products. The alloy was austenitized at 1150°C, aircooled to 510°C, rolled unidirectionally at this temperature to 93 pct reduction of cross-sectional area, and finally oil-quenched to room temperature. Partial transformation to martensite was accomplished by quenching to -196°C as needed. The rolled stock was reduced in thickness from 0.067 to 0.010 in. by etching in a solution of 5 pct HC1, 45 pct HNO3, and 50 pct water, and further thinned by careful mechanical polishing to maintain the two sides of the sheet parallel within 0.0003 in. After mechanical polishing to 0.005 in., electropolishing in 1:9 perchloric-acetic acid solution produced a final thickness of 0.002 in. The preferred orientations were determined from

Jan 1, 1968

By D. Havlena, A. S. Odeh

The use of the straight-line method of solving the material balance equation is illustrated by means of six field cases. Also, the application of statistical criteria to arrive at the most probable answer is shown. The theory underlying the straight-line method of solution and the applicability of the statistical criteria was presented in a previous paper.&apos; The field cases include saturated and undersaturated oil reservoirs with and without water drive. The aquifers discussed are: limited radial, infinite radial, very small aquifer and infinite linear. The field cases also include a gas reservoir producing under water drive. INTRODUCTION In a previous paper,&apos; the authors presented the theory underlying the solution of the material balance as an equation of a straight line. The appropriate equations for various material balance cases as well as the methods of analysis and interpretation with comments and discussion were also included. To illustrate the various theoretical cases treated previously, five field cases are analyzed in this paper by employing the straight-line method of solving the material balance equation (MBE) and one example previously published is referred to. The use of statistical criteria to arrive at the most probable answer is also shown. All the field examples presented, except Case 2, are excerpts from complete reservoir studies. To illustrate the method, only sections specifically dealing with the material balance principles are included. Additional geologic information and basic data are reported to better acquire an understanding of the cases and thus to better follow the reasoning that suggested the successful application of the straight-line method of solving the MBE. The six cases are: (1) saturated reservoir, small gas cap, limited aquifer; (2) saturated reservoir, very small gas cap, infinite aquifer; (3) undersaturated-saturated reservoir, very small aquifer; (4) highly undersaturated reservoir, no water drive; (5) high undersaturated one-well reservoir, limited aquifer; and (6) gas reservoir, infinite linear aquifer. THE D4 SAND, GUICO FIELD, VENEZUELA The D, sand, which was discovered in 1943, is presently in a depleted state. Since its discovery it has produced under water drive, gas-cap-gas expansion, and solution gas drive. In Nov., 1947, water injection was initiated to arrest further pressure decline. When discovered, the D, sand was a saturated reservoir with a gas cap /oil zone volume ratio m estimated volu-metrically at 0.0731, an average permeability of 500 md, a porosity value of 25 per cent, and an oil viscosity at reservoir conditions of 0.3 cp. The volumetrically determined stock-tank oil initially in place was 23.1 million bbl. The volumetrically weighted physical data and production data available until Nov., 1953 are reported in Table 1. In Ref. 1, the effects on the straight-line plot of various values of ro/r for a constant ?to, or of various dimen-sionless times for a constant r8/r10 were theorized and were illustrated in Fig. 3A of that reference. In this field case, the previously theoretically predicted effects are established. Thus, the MBE calculations using Eq. 3c of Ref. 1 were performed for various r6/r10 and dimension-less time values. Eq. 3c of Ref. 1 is:

Jan 1, 1965

By L. C. Brown, S. K. Behera

The diffusion rate in Ag-Sb couples is sensitive to con~pressive load with the width of Ag3Sb, the only phase present in the diffusion zone, increasing with stress up to 800 psi and remaining constant above this. Kirkendall marker experiments show silver to diffuse much faster than antimony in Ag3Sb and incipient porosity may therefore develop at the Ag/Ag3Sb interfnce restricting the transfer of atoms from the silver into the diflusion zone. Application of compressive stress reduces the tendency for porosity to develop and so increases the growth rate. In a recent paper Brown et al.1 observed a significant increase in the thickness of Cu2Te in Cu-Te diffusion couples on application of a compressive stress as low as 20 psi. Similar stress effects have also been observed in the Fe-A1,2 Al-u,3 arid cu-sb4,5 systems. It has been suggested that the increase in growth rates of intermetallic phases in these systems is due to a decrease in the amount of Kirkendall porosity with applied stress. In the present paper, results are presented of the effect of compressive stress on diffusion in Ag-Sb, together with a detailed examination of the Kirkendall effect. The Ag-Sb phase diagram6 shows that antimony has a moderate degree of solid solubility in silver, 5.7 at. pct at 350°C, but that there is essentially no solubility of silver in antimony. There are two intermediate phases— (hcp7) from 8.8 to 15.7 at. pct Sb and Ag3Sb (orthorhombic8) from 21.8 to 25.9 at. pct Sb. EXPERIMENTAL Diffusion couples were prepared from fine silver of 99.95 pct purity and from antimony of 99.7 pct purity. Both the silver and antimony were produced in the form of discs 1/2 in. in diam by approximately $ in. thick, with surfaces ground flat to 3/0 emery paper. Diffusion anneals were carried out in the apparatus previously described.1 A compressive load was applied to the diffusion couple through a lever arm system, with a reproducibility estimated to be ±10 psi. All runs were carried out in a protective hydrogen atmosphere. Following the diffusion anneal specimens were sectioned and polished and the width of the diffusion zone was measured metallographically. Composition profiles were measured using an electrostatically focused electron probe with a spot size of 10 , counting on Sb L radiation. Corrections for matrix absorptiori and fluorescent enhancement9 were not required. S. K. BEHERA, formerly Graducate Student, Department of Metallurgy, University of British Columbia, is now Postdoctoral Fellow, Whiteshell Nuclear Laboratories, Atomic Energy of Canada Ltd., Pinawa, Manitoba. L. C. BROWN, Junior Member AIME, is Associate Professor, Department of Metallurgy, University of British Columbia, Vancouver, B.C., Canada. Manuscript submitted June 14, 1968. IMD RESULTS Fig. 1 shows an electron probe traverse of a typical diffusion zone. In all couples examined only one intermediate phase was observed and the composition of this phase, 23 wt pct Sb, was in good agreement with the composition of Ag3Sb, 23 to 28 wt pct Sb. The presence of this phase was confirmed by X-ray diffraction of filings taken from the diffusion zone. The probe traverses showed no detectable solid solubility in either the silver or the antimony although the phase diagram indicates that some antimony, up to 6.5 wt pct pct Sb, should be in solid solution in the silver. However the width of this portion of the diffusion zone would be expected to be very small in view of the low diffusion coefficient in the silver, 4 x 10-l6 sq cm per sec at 350°C, 10 compared with that in the Ag,Sb, estimated as 3 x 10-8 sq cm per sec in the present work, and this region would therefore not be expected to be seen in the probe traverse. Application of stress resulted in a significant increase in the width of the diffusion zone, Fig. 2. At 350°C, the thickness of Ag3Sb increased from 250 at 0 psi to 400 p at the limiting stress of 800 psi, indicating an apparent 150 pct increase in the diffusion coefficient. Similar behavior was also observed at 400°C, indicating that the stress effect is not characteristic of just one temperature. The growth of Ag3Sb at 350°C and at various stresses is shown in Fig. 3. In every case the growth rate was parabolic indicating diffusion control. The kinetic curves all passed through the origin showing that delayed nucleation of Ag3Sb was not responsible for the stress effect and that it was a real growth effect. A series of tests were carried out in which diffusion was allowed to take place at a lower stress following an initial high stress diffusion anneal. Speci-

Jan 1, 1969

By P. Nelson, K. L. Gunsallus, A. R. Ingraffea, J. F. Beech

INTRODUCTION Fracture toughness, KIC, is an intrinsic material property and is a measure of the energy required to create new surface area in a material. Fracture toughness measurements can be made for a wide range of rock types (Ouchterlony, 1980). As a measure of energy of comminution, fracture toughness might be used for more sensitive predictions of Tunnel Boring Machine (TRM) performance than are possible with other index measures in current use. This paper describes part of an ongoing, comprehensive, analytical/experimental program aimed at evaluation of KIC in such a role. The program includes efforts to: 1. Provide a firm analytical basis for a test specimen geometry: the core-derived short-rod. 2. Develop simple, inexpensive testing equipment and techniques. 3. Evaluate the accuracy of the above by testing rock and other materials and comparing the measured fracture toughness with those obtained by other methods. 4. Measure fracture toughness of a substantial number of different rocks from three ongoing TBM projects. 5. Compare fracture toughness results with other strength measures. 6. Compare all test results with observed TBM performance in the three projects. Presented here are summaries of all but the last of these efforts. Comparative evaluation of KIC as a more senstive rock property for TBM performance prediction will be the subject of the oral presentation and a subsequent paper.

Jan 1, 1982

By J. A. Cahill, A. D. Kirshenbaum

Using an alumina or zirconia crucible with an alumina sinker or a molybdenum sinker coated with zirconium dioxide, the density of liquid iron was determined by the immersed-sinker method over the temperature range of 1800" to 2500°K. The density, with respect to temperature, is ex-Dressed by the equation Dg/cm = 8.523 - 8.358 X 10 T&apos;K The molar Volumes and thermal coefficients of expansion were calculated. Iron, upon me1ting, was found to expand 3.5 pct. A basic knowledge of the physical properties of materials at high temperatures is becoming increasingly important. A check of the literature shows, that in spite of the importance of iron, very few measurements have been made of its physical properties in the liquid state. Density measurements have been made by Benedicks and his collaborators1g using the method of balanced columns, by Desch and smith4 using the immersed sinker method with an alumina sinker, by Lucas using the maximum bubble method5 and by Stott and endall&apos; who used an alumina pyknometer. In the method of balanced columns, the difference in level of molten iron in two arms of a U-tube, together with the corresponding difference of pressure had to be measured. The formation of gas bubbles in one or both arms was a great source of error. These values are very erratic. They vary from 6.83 to 7.45 g per cm3 at the melting point (1805"~) and from 6.45 to 7.15 g per cm3 at 1890°K. Stott and Rendall determined the density at 1837"K, with a reproducibility of *0.2 pct. They used an alumina pyknometer fired to 1973°K. The vessel was filled in a vacuum furnace by immersion in the liquid metal. When thermal equilibrium was attained, the pyknometer was withdrawn, cooled, the ingot removed and then weighed. The chief disadvantage of the method was the difficulty of inserting the pyknometer without cracking it. The authors have been able to determine the density of liquid iron from its melting point up to 2500°K, by using the immersed-sinker method, with A1203 or ZrOz crucibles and A1203 or molybdenum sinkers coated with Zr02, Fig. 1. EXPERIMENTAL Apparatus. In these studies the source of heat was the carbon tube resistance furnace with an argon atmosphere described previously.7 Experimental runs were made using either Ala3 or ZrOz crucibles. The sinkers used were 1) pure A1a3 and 2) molybdenum coated with ZrOz. The crucible, 2 1/8 in. in diam and 3 in. high, was centered in the furnace on an Ala3 of Zr02 pedestal. The sinker, 1/2 in. in diam and 1 1/2 in. long, together with a counter weight, was suspended from an analytical balance into the melt by a molybdenum wire. Procedure. The procedure, as described previously,&apos; consisted in measuring the weight loss of the sinker in the liquid iron while determining simultaneously the liquid iron temperature by means

Jan 1, 1962