Search Documents

By J. K. Abraham

In recent years there has been interest displayed in the precipitation phenomena occurring in austenitic alloys based on the binary Fe-Ni system.1'2 Previous communications have been extended covering the kinetics of clustering in the Fe-Ni-Ti system and the effect of cluster size on subsequent mechanical properties.3'4 To a great extent the question of coherency, which has a dominant role in determining the mechanical properties, is dictated by the degree of misfit between the precipitate and matrix. Thus, the change in lattice parameter of the matrix with composition is an important variable that should be examined. The lattice parameter, ao, of austenite was determined for Fe-29.75 Ni-1 to 6 Ti and Fe-27 Ni-1 to 10 Ti alloys in this study. The alloys used in this investigation were melted in a vacuum induction furnace from a starting stock of plast iron (99.95), electrolytic nickel (99.9), and ti- tanium sheet (99.5) in a MgO crucible. The alloy compositions in atomic percent are given in Table I and their relative position in the Fe-Ni-Ti ternary is indicated in Fig. 1. The chemical analyses were taken from the homogenized bulk materials treated in a manner related earlier.3 A diamond file was used to obtain powder from the bulk. To remove the stresses induced by filing, the powders were austenitized at 1875°F for

Jan 1, 1969

By George Rice

THE subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on bumps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free' from folding and faulting.

Jan 1, 1935

[ ]

Jan 1, 1938

By Lawrence Adler

For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.' This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.'

Jan 5, 1960

Further discussion of the paper of JAMES JOHNSTON, presented at the New York meeting, February,. 1914, and printed in Bulletin No. 85, January, 1914, pp. 107 to 133. See also Bulletin No. 91, July, 1914, pp. 1473 to 1496. THOMAS CROWE,* Victor, Colo.-The interest manifested of late in the treatment of low-grade ores, together with Mr. Clevenger's discussion of the Mill and Metallurgical Practice of the Nipissing Mining Co., prompts me to acid a few remarks relative to concentration in connection with cyanide treatment of low-grade ores. Mr. Clevenger in this discussion does not condemn concentration in this connection, but, nevertheless, the tone of his remarks would lead one to believe that his conclusions are like those of many others: that concentration is often turned to as a last resort in an attempt to improve or obtain an extraction upon an ore by the recovery and sale of the refractory portion of the ore. This, I will attempt to point out, is not always the case. Concentration in connection with cyanidation often performs an entirely different function, i.e., one of saving fine grinding. Economy being the keynote of successful treatment of low-grade ores, the problem often becomes more commercial than metallurgical, and, as there is generally a definite ratio existing between cost of operation, degree of comminution, and percentage of extraction, the grade of ore under treatment usually imposes a limit upon these factors. With many ores grinding is the most expensive single item in their treatment; therefore, the degree of comminution is very apt to be governed by the allowable cost of operation. With most ores the degree of comminution controls to a great extent the percentage of extraction. So in the treatment of low-grade ore it often becomes necessary to sacrifice extraction, through coarse grinding for the benefit of cost, in order that the greatest ultimate profit may be obtained, and it is under these conditions that it is, possible for concentration to play an important part in overcoming to some extent the effect of mesh. The precious metals occurring in an ore are usually closely associated with the metallic portion of the ore, and as this metallic portion is generally fairly well liberated from the gangue at comparatively coarse meshes, further grinding of the ore is necessary only in order that the metallic portion may be reduced sufficiently fine that the precious metal part of it may be dissolved by cyanide solutions in a reasonable length of time.

Jan 11, 1914

HAVING previously shown you how ores are found and mined, and also how they are prepared and disposed for smelting, and then how the blast furnaces and other furnaces are made for purging their earthiness, all this would be as nothing if I did not proceed to show you the method of smelting them. Therefore, in the present chapter I wish to show you how you must proceed in this very important operation, telling you all I have seen and also how much work with this kind of blast furnace I have done or directed. For this reason I tell you first to take by weight or measure the quantity of ore that you wish to smelt and, particularly if it is a kind that contains silver, break it into small pieces about the size of [52v] beans. If the ore had previously needed evaporation by fire or cleaning by washing, you will have had this done well and have had it properly prepared by a master sorter or others. A layer of this is arranged on a bed of planks, bricks, or flat stones in front of the blast furnace and its companion is placed on top, then a quarter part of galena or a third if you can obtain it. Then an equal part of crushed iron slag or slag from the same or different ore is added. These materials are spread in layers one above the other. When the blast furnace has been constructed as taught above, correct in all its parts, and is full of well-kindled burning charcoal, then fill it up with charcoal and admit water to the bellows machine. When you see that it is well kindled again from this wind and that the flames begin to come out forcefully on top, work it down with a little rake and fill it up again. Then the pannier is filled with new charcoal, the blast furnace heaped full, and another basketful of the said composition of ore is also put on top. Proceed in this way, continually adding charcoal and ore as long as you have any, or as long as you wish to keep up the work, maintaining the blast furnace always full, or continuing in this way until the bottom of the blast furnace is filled with melted materials. Decide this by judgment, or by seeing through the mouth of the tuyère where the wind of the bellows enters that they are level with this. Then with an iron tool open the hole that was left as an outlet in front of the blast furnace and allow all the metal with its slag to run out. These two things, flowing through the chan-

Jan 1, 1942

By B. C. Riblet

THE president of a large smelting and refining company once telegraphed me that they had acquired extensive mining interests in northern Peru and requested me to inspect their properties as it would be necessary to install a system of aerial tramways between their mines and treatment plant. The concentrator was about 50 mi. from the coast, reached by a fairly good motor road. From the concentrator an aerial tramway would he required, about 6 mi. long, to their first property, a gold and silver mine. The lower terminal of the tramway was at an elevation of 4000 ft. and the mine at an elevation of 9500 ft.

Jan 1, 1937

By Frank J. Windolph

Grinding Practice-These tests were run in the 9 ft diam by 8 ft long grate discharge ball mills at Climax. Each mill functions in closed circuit with a 78 in. Akins duplex high-weir classifier, and a circulating load of 300 pct is maintained. The size of the mill feed is 6 pct on 3/8ths, which is ground to pass 28 mesh. Testing Methods-Each grinding section is equipped with a conveyor scale on the ball mill feeder belt, a watt-hour meter on the ball mill motor, and an automatic sampler for the ground product. These instruments are exceptionally valuable to the mill testing program.

Aug 1, 1956

By P. W. Andrews, R. B. Toombs

ECONOMIC STRUCTURE OF MODERN INDUSTRIAL ECONOMIES The role of minerals in modern industrial economies may be examined in several ways. There are relationships with the various sectors of the economy: the primary, secondary, and tertiary industrial groupings and activities. Mineral supply and demand activities can be measured in terms of national accounts criteria. The economic policy objectives of the modem industrial economy are based to a considerable extent on the needs of the nation for economic supplies of miner- al materials. There is an important role for minerals relative to national security in peace and in wartime and many national policies are directed toward ensuring adequate sup- plies of minerals. Environmental control in the modem industrial economy is increasingly concerned with matters related directly to the production and use of minerals and these matters, in turn, bear importantly on conservation in mineral supply and demand. Mineral polices include specific provision for research and development activities concerned with the production and the use of minerals. In all, national policy objectives will be shaped in considerable part by the circum- stances of mineral supply and demand: the relative degree of availability from domestic and foreign sources, the state of the mineral-processing industries, and the degree of development of the mineral-using industries, and per capita and total changes in requirements. Goods made from mineral raw materials are the basis of all advanced societies and although this is taken for granted, every country is continually dealing with problems of mineral supply and demand. Considering that in the first 50 years of this century the consumption of mineral materials in a highly Industrialized country such as the United States increased by six times while the population was doubling, it becomes apparent that if a country is to enjoy rapid economic growth it must have access to huge and ever-growing supplies of mineral materials at lowest possible cost. Adequate supplies of mineral materials and wise usage of mineral resources have always been among the most important determents of a nation's survival The importance of access to adequate mineral supplies is increasing every year and this has significant international, as well as national, implications because of the unique locational characteristics of mineral resources. It is generally acknowledged that no particular type of natural resource is essential to a high level of national income or to economic progress. A country's endowment of natural resources need not exercise a determining influence on the course of its national income over time, provided it is able to trade. What is required for economic progress is the availability of a substantial quanti-

Jan 1, 1976

By William M. Brewer

Until quite recently, in fact within the past two gears, but little attention has been given to the outcrops on the west coast of Vancouver Island, and their copper-contents. During the past few months the writer has been engaged in examining and developing some of these prospects. In many respects he has found characteristics associated with these prospects which, in his experience, are unique. In the first place, nearly all the outcroppings which overlie chalcopyrite-ore along the west coast of the island are composed of a high-grade magnetite. The magnetic qualities of some of these outcrops arc so pronounced that the magnetite possesses polarity. Although the writer hinlsclf had no analyses of this magnetite made, yet from its appearance he can readily believe that analyses made for other parties, which show a yield' of 62 or 63 per cent. of metallic iron, with only traces of phosphorus and silica, are correct. At a very shallow depth, masses of chalcopyrite, yielding in some instances as high as 32.6 per cent. of copper, occur associated with the magnetite; and in one instance, which recently came under the writer's observation, a solid body of high-grade chalcopyrite, fully 4 feet in thickness, occurs Within 6 feet of ; the surface. Usually this solid sulphide-ore carries low values in gold. Probably ail average of' $2 per toil would be fairly representative. But in some instances development has determined the occurrence of narrow stringers of pyritous quartz, associated with the sulphide-ores, which yield by assay more than $20 per ton in gold. In the districts examined by the writer, the country-rock is usually crystalline limestone, with dikes of igneous rock as intrusions. Sometimes the outcrops of magnetic iron-ore are

Jan 1, 1900

By W. J. Parton

The efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/32 by 1/32 in.) and No. 5 Buckwheat (1/32 in. by 0), pre-sent a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than 3/32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes. The object of this paper is to de- scribe a stationary screen device from which the underflow is restricted by orifices, called a launder screen, along with operating results of several applications of this screen; a settling tank in which two classified products are produced by the installation of a cylindrical partition of smaller diameter than the original tank, one product being recovered from the small tank created by the partition and one product from the space between the inner and outer tank walls; a small pocket classifier or hydraulic trap for use in removing high ash particles from a sludge flow; the classification or segregation of sludge solids occurring in a 16 in. diam pipe flow by analysis of samples procured at different zones; and the operating results of a Fahrenwald sizer, as well as the performance of the concentrating tables handling the classified products. These simple devices were employed at the collieries of the Lehigh Navigation Coal Company Incorporated, Lansford. Pa., in order to improve preparation results on the fine sizes of anthracite. Launder Screens The launder screen is a screening and dewatering device which probably could be used advantageously in the flow diagram of many fine coal plants. Fig 1 shows that it consists of a stationary screen constructed by placing 6 in. high partitions every 6 in. along a launder. Holes are then drilled on 6-in. centers across the bottom of the launder to receive pipe bushings of the desired diameter. The screen cloth is tacked on top of the partitions. When water and solids are fed to the screen, only a small portion of the total water is removed through the orifices in each compartment so that the water in the feed is distributed evenly over the whole length of the screen. The screening action which results is very efficient because the solids are kept in a fluid condition for the full length of the screen. Blinding of the screen can be minimized by the use of screen cloth

Jan 1, 1950

By Theodore R. Butkovich, Jesse L. Yow

Geological storage of spent-fuel assemblies from an operating nuclear reactor has been underway since the Spring of 1980 at the U.S. Department of Energy's Nevada Test Site. The primary objective of this generic test is to evaluate granite as a medium for deep geological storage of high level reactor waste and to provide data on thermal and thermomechanical behavior of granite from imposed heat loads.(l) The underground installation in the Climax stock granite was sited at about 420 m below the surface and 145 m above the existing water table. As shown in Figure 1, three parallel drifts were excavated spaced on approximately 10 m centers. Seventeen storage holes were drilled at the central drift on 3 m centers in which eleven spent fuel canisters and six thermally identical electrical simulators were emplaced. Electrical resistance heaters were emplaced in vertical holes in the floor of the side drifts on 6 m centers. The thermal output of these heaters is being periodically adjusted to simulate the thermal response of a large storage array. Rock and ventilation air temperatures are being measured continuously in the drifts and throughout the rock surrounding the excavations. Measurements of drift deformation have been made routinely since the emplacement of the spent fuel. Both vertical and horizontal measurements are being taken at five locations along the heater drifts and at six locations along the central canister drift (Fig. 1). Two types of instrumentaton are being used: convergence wire extensometers which are monitored automatically, and a manually operated tape extensometer with which measurements are taken periodically. The tape extensometer measurements were initiated about 6 weeks following fuel emplacement. The lack of a temperature correcting capability for the convergence wire extensometers make that data unavailable for analysis at this time.

Jan 1, 1982

US 4,185,996 -- Removal of arsenic and sulfur Impurities from arsenic-containing cobalt sulfide ore. The ore is oxidized In air at a temperature of 700 to 800°C for 3 to 8 hr to drive off the bulk of the sulfur The oxidized ore 1s heated with a reducing gas at a temperature of 700 to 800°C for 2 to 6 hr to volatilize arsenic, and the final calcine 1s leached with an acid to eliminate substantially all of the remaining arsenic. A.R. Zambrano, assigned to Hanna Mining Co Jan. 29, 1980. 3 pp. (75-2). Filed. 2-13-78 (877,002).

Jan 1, 1982

By W. J. Keep

Cast-iron, or pig-iron, is iron which contains all the carbon that it could absorb during its reduction in the blast-furnace. As is well-known to chemists, carbon exists in cast-iron in two distinct forms. In chemical union, as "combined" carbon, it cannot be discerned, except as it may increase the whiteness of the fracture, in so-called white iron, or carburetted iron (sp. gr. about 7.72). Carbon mechanically mixed with the iron as graphite is visible, varying in color from gray to black, while the fracture of the iron, according to the color and amount of graphite it contains, ranges from a light to a very dark gray. The specific gravity of graphitic iron is about 7.40. Silicon in cast-iron is evidently to some extent combined with the iron and the carbon ; but whether it exists also in a form corresponding with graphitic carbon, mechanically mixed with the remaining mass, is a question still in dispute, which we have not in this paper endeavored to answer. It has been the opinion of many writers on metallurgy, and many foundry men, that silicon is in every way injurious to cast-iron. Yet

Jan 1, 1889

By Basil B. Zavoico

During 1938 the Russian oil industry, while able to increase its production 4.69 per cent above the preceding year, was not successful in correcting some of its basic difficulties, and the industry's position as it entered 1939 was unsatisfactory. The internal political difficulties of 1937 and 1938 took a toll in the oil industry as they did elsewhere in the U. S. S. R., further complicating the solution of the problems facing it, most important of which still remain: lack of experienced and responsible leadership, able to make quick decisions; undisciplined and migratory labor; and insufficient and often unsatisfactory quality of the various equipment needed by the industry and its ineffective distribution. Recent developments in the U. S. S. R. suggest that during 1939 the management will be granted more latitude and hence somewhat better results may be anticipated from the executive branch, provided, however, the "purges" do not recur. The labor should be better disciplined and should not shift as easily, owing to the introduction, at the close of 1938, of individual labor passports to all workers in the country, the principal purpose of which is to correct those two deficiencies. It is not anticipated, however, that the service of supply will show any appreciable improvement in 1939, partly because of inherent difficulties and partly because the manufacturers of heavy machinery are working primarily and necessarily for munitions. Production Production of crude oil during 1938 is estimated at 224,714,000 bbl., as compared with 212,742,000 bbl. in 1937, an increase of 4.69 per cent but 12.76 per cent below the planned output. While there were no major readjustments in the source of supply of crude oil, both the older districts, Baku and Grozny, were barely able to maintain their 1937 levels of production, the increased output being supplied primarily by the fields of Maikop and Ural Permian Basin districts. While exploration work was outstandingly successful in 1937, in 1938 no discoveries of any

Jan 1, 1939

By Basil B. Zavoico

During 1938 the Russian oil industry, while able to increase its production 4.69 per cent above the preceding year, was not successful in correcting some of its basic difficulties, and the industry's position as it entered 1939 was unsatisfactory. The internal political difficulties of 1937 and 1938 took a toll in the oil industry as they did elsewhere in the U. S. S. R., further complicating the solution of the problems facing it, most important of which still remain: lack of experienced and responsible leadership, able to make quick decisions; undisciplined and migratory labor; and insufficient and often unsatisfactory quality of the various equipment needed by the industry and its ineffective distribution. Recent developments in the U. S. S. R. suggest that during 1939 the management will be granted more latitude and hence somewhat better results may be anticipated from the executive branch, provided, however, the "purges" do not recur. The labor should be better disciplined and should not shift as easily, owing to the introduction, at the close of 1938, of individual labor passports to all workers in the country, the principal purpose of which is to correct those two deficiencies. It is not anticipated, however, that the service of supply will show any appreciable improvement in 1939, partly because of inherent difficulties and partly because the manufacturers of heavy machinery are working primarily and necessarily for munitions. Production Production of crude oil during 1938 is estimated at 224,714,000 bbl., as compared with 212,742,000 bbl. in 1937, an increase of 4.69 per cent but 12.76 per cent below the planned output. While there were no major readjustments in the source of supply of crude oil, both the older districts, Baku and Grozny, were barely able to maintain their 1937 levels of production, the increased output being supplied primarily by the fields of Maikop and Ural Permian Basin districts. While exploration work was outstandingly successful in 1937, in 1938 no discoveries of any

Jan 1, 1939

By Walter Renton Ingalls

Metallurgical literature has no record of any ore beneficiated for cadmium alone, and the cadmium of commerce is derived from zinc ore, with which cadmium is generally associated. Zinc ores free from cadmium—e.g., the ores of the Franklin and Stirling mines, New Jersey, and of Broken Hill in Rhodesia—are rare. Blende concentrates of 50 to 60 per cent grade have contained (in production of important tonnage) as much as I per cent Cd, which is unusually high. The concentrates from the Tri-State district average from 0.3 to 0.4 per cent Cd, which is high. The concentrates from mines west of the Rocky Mountains seldom are higher than 0.2 per cent. In the periodic system of the elements, cadmium is in the same group with zinc. Its properties and compounds are similar. Its metallurgy is also similar. Cadmium has a melting point of 320°C. and a boiling point of 778"C., while the melting point of zinc is 415'C. and the boiling point gos°C. These conditions, together with the lower reduction temperature of cadmium oxide, indicate means for. separating cadmium from zinc. Cadmium in spelter is viewed, if not as an impurity, at least as an alloying element that may be objectionable, its special effect being hardening. However, for some purposes, a little cadmium in spelter is desired, and 0.4 per cent may be permissible, even in spelter for rolling. Cadmium in spelter for brassmaking is completely volatilized at the temperature of that process, and in bygone days an immense quantity of cadmium must have been lost in the fumes from these furnaces. Pyrometalltjrgy—Early Cadmium compounds, sulphide and oxide, being more volatile than the corresponding compounds of zinc, loss of cadmium begins to occur from the first furnace operation. In normal roasting, even with Tri-State ore, this loss may not be very high. Raw ore, assaying 0.4 per cent Cd, may be expected to give a roasted product of the same assay, which would imply a cadmium loss of about 15 per cent. Roasted ore, assaying 0.4 per cent Cd when distilled at ordinary furnace temperature, yielded spelter containing about half of that in the ore charged. The first draw of spelter under these conditions may assay 0.8 per cent Cd (accounting for 22 per cent of the cadmium recovery) and after the several draws of spelter have been equalized the cadmium content may average 0.35 per cent. If, therefore, 2000 lb. of blende averaging 0.35 to 0.4 per cent Cd is roasted and distilled, there may be obtained 1000 lb. of spelter, assaying 0.35 per cent Cd or 3.5 lb. content, which entering into Prime Western spelter will be sold at the spelter price. It will be observed from the outline hereinbefore (summarizing conditions prior to the introduction of sintering) that the main loss of cadmium occurred in the distillation process and by failure to condense, which could be ameliorated by attaching a prolong to the condenser, thus collecting

Jan 1, 1944

By Carl L. Renzoni

INTRODUCTION This paper defines equity as the issuance of a permanent interest in the business on a broadly distributed basis. As such, it excludes the issuance of equity to either a merchant bank or to another corporation. Nearly twenty years ago the equity markets were very simple: The instruments used were primarily common shares, convertible debentures or convertible preferred shares. Another equity-type option often used, especially by junior companies, was the sale of joint venture interests. Issue sizes were generally in the order of $25 - $100 million and issues were syndicated primarily in North America and Europe by one or two investment dealers. Mining corporations today benefit from a market with much more depth. Issues are syndicated by dealers on a truly international basis, and issue sizes now often range up to $300 million. Moreover, dealers are now willing to take significant risk in buying the issues for redistribution. This discussion of trends in equity markets will encompass: 1) common shares 2) warrants to buy common shares 3) convertible debentures 4) commodity backed instruments A review follows of events that affect the mining industry and investment dealers as they have a bearing on the equity markets for the metal producers. FACTORS AFFECTING THE MINING INDUSTRY The current business cycle, up to October 1987, had been characterised by a buoyant stock market and depressed base metal prices. Mining companies entered this period with weak balance sheets and little prospect of cash flows meeting capital needs. The issuance of equity and the sale of assets were used extensively to reduce debt to manageable levels. During this period, the relative high price for gold, and more important, the very high earnings and cash flow multiples afforded to gold producers, caused companies to target gold as the only game in town. The need for capital to acquire and develop gold properties prompted an unprecedented volume of equity issues. (Burns Fry led or co-managed over $1 billion of mining equity issues per year during this period). This high demand for equity capital by the industry prompted an increase in the use of equity instruments, such as commodity backed instruments. In addition, government tax incentive programs in Canada, such as flow-through shares, allowed smaller companies to raise significantly more equity than would otherwise have been possible. Over $1 billion in flow-through equity was raised in 1987 alone. The abundance of flow-through capital in Canada made it easy to form a new company. One flow-through share fund developed a system of providing the working capital required for a company to be eligible to receive flow-through share capital so that an entrepreneur required only a mining property to get started. Many new companies were formed and several flourished in a buoyant stock market environment to the point that market capitalizations grew to $100 million or more. The current period is in stark contrast to that before October 1987. The equity markets are generally available to the resource industry only on a window basis and only for senior companies and for special situations. The industry is benefitting from buoyant metal prices, and bankers are anxious to provide debt capital. Investment dealers previously processing several equity issues

Jan 1, 1990

By Courtenay de Kalb

REVISION of the United States mining law is needed. chiefly because of the following reasons: 1. The conceptions as to the characteristics of orebodies that were held at the time the statute of 1872 was enacted have since proved to be in many respects erroneous. 2. The operation of the existing law has been found to work unnecessary hardship upon many claimants to mineral land. 3. The existing statute fails in large degree to encourage development of mineral resources. 4. The existing law often produces conflict between placer and lode-claim rights, working unnecessary injustice to placer claimants. 5. The methods of establishing the rights of locators on United States mineral land are defective, and are not uniform throughout the States within which such lands exist. LAW OF THE APEX The objections to the so-called "law of the apex" are so well known as to require no detailed statement. It is sufficient to point out that the apex rule was based upon the notion that ore deposits consisted of well-formed veins included between definite walls, like the slice of ham in a sandwich. The fact is that veins conforming to that simple type are rare. Irregularity is the rule, and the chief metal production of the United States comes from masses which bear no resemblance to the tabular form of vein. Manifestly the law of the apex fails completely in such cases. Moreover, the tendency is constantly toward the exploitation of ores of lower grade than could formerly be worked, and such deposits exist mainly in the form of large irregular impregnated zones and masses, so that the future. development of our mineral resources would be continuously embarrassed by shadowy claims to extra-lateral rights by the locators of so-called apexes

Jan 2, 1915

By Colin C. Harris, Nathaniel Arbiter

Current scale-up procedures are discussed critically, including: constant specific energy criterion; determination of mill size and power for a given ore, throughput and mesh of grind; specification of operating speed and loading. A major dynamic and kinetic factor now recognized is that the ratio of media rotational flow to ore axial flow, and the number of mill revolutions that ore is subjected to during residence, both diminish as mill diameter increases. These factors can lead to capacity limitations when mill diameters reach a critical range, especially regarding coarse sizes. Experience at the Bougainville and Pinto Valley operations is contrasted. Corrective measures suggested are to reduce loading and increase speed towards the Davis best operating speed.

Jan 1, 1982