Search Documents

By Y. C. Liu, G. A. Alers, S. S. Choi

In searching for an explanation for the obvious difference between the copper and the brass type of rolling texture, it is common practice to look for correlations with other properties. For example, there are obvious differences between copper and brass in the critical resolved shear stress, the extent of easy glide or stage I, and the amount of "overshooting)) during single-crystal deformation.' Also, the slip lines in copper are fine and wavy while those in brass are more coarse and better described as slip bands.' Since neutron irradiation is known to make these properties in copper change in such a way as to resemble brass,2'3 an excellent test for these possible correlations is to see whether neutron irradiation produces a corresponding change in the texture, i.e., whether irradiated copper develops a brass-type rolling texture. The experiment would also answer the more important question of whether or not lattice defects like those introduced by neutron irradiation have any effect on the development of rolling textures in fcc metals. Experimental studies using conventional X-ray pole figure techniques are inconvenient because the X-ray detection system must be modified to discriminate against the radioactivity which is induced in the specimen by the necessarily long exposure to neutrons. Nevertheless, some texture determinations have been

Jan 1, 1968

By N. Mohan, A. K. Biswas, V. Y. Sampat Kumar

At low sodium-oleate concentration, calcite flotation is substantially improved by the use of CO2 instead of air. Electrophoretic mobility measurements indicate that carbonation results in the accumulation o f positive charge on the calcite particles. This heightens adsorption of oleate anion, an effect confirmed by tracer-technique measurements. Fundamental insight is obtained as to how CO2 serves better as an activator than some mineral and organic acids, how oxalic acid acts as a depressor, and why the influence of Ca++ ions, liberated during carbonation, on flotation behavior of calcite is insignificant and sometimes adverse.

Jan 1, 1972

By W. R. Seyfried

THE problem of extracting alumina from clay and low-grade bauxites has been the subject of considerable interest for some time. The basic reason, of course, lies in the fact that known reserves of high-grade bauxite are not inexhaustible and that the present commercial process cannot successfully cope with low-grade bauxites or clay. Ultimately it may be necessary to use these poorer raw materials for all commercial operations. An unprecedented demand for aluminum during the war emergency and the constantly threatened shortage of imported bauxite caused the United States Government to take an active role in this problem. Through the National Academy of Sciences, the War Production Board and the Defense Plant Corporation, it investigated processes and finally selected four to be used in the construction and operation of four experimental plants. Each plant was to be designed in such a way as to facilitate its incorporation into a larger commercial plant should the need arise. The Chemical Construction Corporation process, or "Chemico" ammonium sulphate process as it is better known, was one of the four selected. The extensive literature and patents on record before the war generally follow one of two process-types depending upon the extracting reagent used. One group uses an acid reagent, the other an alkali. The Chemico process uses an acid reagent. For those interested in other processes described in literature, there is a short bibliography at the end of this paper. The basic steps of all acid extraction processes are: (I) to make the aluminum silicates acid soluble, (2) to separate the released alumina from impurities and insoluble gangue, and (3) to recover the reagent for re-use. THE PROCESS AS PLANNED In April 1941, a group of chemists and engineers of the Chemical Construction Corp. became interested in the problem of extracting alumina from clays and low-grade bauxites and, under the leadership of Mr. Blakeslee Barnes, Vice President and General Manager of the Company, first drafted a process in July of that year-five months prior to Pearl Harbor. The work continued in our research laboratories and with a small pilot plant. By June 1943, the work had progressed to a point where it was possible to apply for a patent on the process which was U.S. patent 2,405,426, granted August 6, 1946. Immediately prior to the development of the Salem plant, the process was envisaged to be as follows: I. The first step was to make the aluminum silicates acid soluble. It was planned: (a) Clay or low-grade bauxite would be roasted at 700 to 800°C (1292° to 1472°F), (b) The roasted ore would then be leached with hot aqueous ammonium bisulphate to form a slurry. In this way the

Jan 1, 1947

By Harold H. Goe, Louis V. Bender

The recovery of arsenic was started at the Washoe Reduction Works (later called the Anaconda Reduction Works) in 1904, when an arsenic plant was constructed adjacent to the lower end of the 60-ft. main flue.' This plant originally consisted of a Brunton roasting furnace for treatment of flue dust and a small reverberatory furnace for treating the crude arsenic produced in the roasting operations, together with the necessary kitchens for condensation of the fumes and grinding and barreling apparatus for preparing the refined white arsenic for market. The Brunton furnace was fired with wood. It was 14 ft. 6 in. in diameter with two outside fireboxes. The hearth revolved upon a central shaft. The charge was fed through a dust-tight hopper on to the center of the hearth and slowly moved to the outer edge of three rows of stationary rabbles fastened in the roof of the furnace. There was a 3-ft. space between the hearth and roof. A crude arsenic was condensed from this furnace. The hot flame from the fireboxes passed directly over the charge, vaporizing the As203 that was carried through brick flues to the condensing chamber. This chamber was 8 ft. high, 16 ft. wide and 240 ft. long, divided into small kitchens by partitions spaced every 7 ft. It was connected with the main flue system to provide draft and to receive any losses from the chamber. The small kitchens were connected by openings in such a way that the fumes took a zigzag course, causing them to come in contact with the cold walls and ceiling and condense the arsenic. There was an opening from the outside into each kitchen, for the removal of the deposited arsenic, which was closed by a wooden door. The refining furnace was a small coke-fired reverberatory having a hearth 10 by 20 ft. in dimensions. It had three hoppers through which the crude charge was introduced, and one firebox placed at one end. The hot gas from the burning coke passed over the charge, volatilizing the arsenic and carrying it to the kitchens.

Jan 1, 1934

By K. Sassa, I. Ito

The dynamic principal stresses induced within rock by an explosion under con fined conditions are analyzed for the case of blasting with one free face by applying the values of measured radial displacement, particle velocity and so on to equations derived from the theory of elasticity. The dynamic stresses on the free face are also calculated from the strain measured by wire strain gauges affixed on the free face. Some results obtained are briefly: 1) The maximum stress on the free face appeared at the intersection between the free face and the burden, and its magnitude was about twice as large as the magnitude of the tangential tensile stress imparted by the incident stress wave within the range related to the breakage by blasting. 2) The maximum value of the compressive stress near the free face was decreased due to the existence of the free face, while that of the tensile stress was increased. 3) At any point near the free face, the directions of the principal stresses in the r? plane using spherical coordinates with the origin at the center of the spherical charge, changed with time except in the direction of the burden. However, at another point near the explosion point where the principal stresses were mainly those stresses caused by the initial longitudinal wave, the directions of the principal stresses coincided with those of the coordinate used. 4) The maximum value of the tensile stress in the F direction was larger than those in the re plane at and near the free face. 5) The tensile stress caused by the Hopkinson effect appeared only near the burden. 6) It is presumed from the results of stress analysis that radial cracks will be produced in the rock mass near an explosion point, but with the approach of the free face, the directions of cracks curve towards a direction parallel to the free face. INTRODUCTION In order to investigate the mechanism of rock breakage by blasting, it is considered to be very im- portant to know how the stresses are generated and distributed within the rock by explosion of a confined charge. As part of a research program concerning the mechanism of rock breakage by blasting, the authors have already published papers on the detonation pressure produced at the inner surface of the charge hole1 and on the behavior of the dynamic stresses within rock caused by an explosion in the case where no free face existed.' In this study the dynamic stresses on and near the free face have been investigated for the case of blasting with one free face. The mechanism of rock breakage in blasting is discussed in the light of these studies.

Jan 1, 1967

By R. R. Hart, B. C. Wonsiewicz, G. Y. Chin

In recent years there has been increased miniaturization of electromechanical devices to keep pace with current trends toward smaller electronic components. A major problem facing the designer, however, is the higher stresses encountered by the material as a result of shorter springs. Hence an improvement in the elastic limit, as approximated by the 0.01 pct offset yield strength, would be highly desirable. An increase of 25 pct in the yield strength, for example, will permit a 20 pct reduction in both the length and thickness of a cantilever-type spring while maintaining the same compliance. One technique of improving the yield strength that has received little commercial attention is crystal-lographic texture strengthening.1,2 Texture strengthening is expected to be most beneficial in materials of hcp structure, but considerable gain can also be expected in cubic materials. A wire with a (111) fiber texture, for example, is expected to be 20 pct stronger than randomly oriented material, and 50 pct stronger than wire with a (100) fiber texture.293 For sheet specimens with a {110}(112) texture, characteristic of many heavily rolled fcc alloys, the (111) transverse direction is expected to be the maximum yield strength direction, about 20 pct higher than that in the (112) rolling direction.' In addition, the (111) direction is the direction of maximum modulus of elasticity for most cubic alloys. A large value of the elastic modulus could be desirable in designs where stiffer springs are required. To test the above idea, a 0.090 in. (-2.3 mm) thick commercial grade A (5 pct Sn) phosphor bronze sheet, a widely-used material for relay springs, was rolled from the spring-tempered condition (60.5 pct reduction) to various additional reductions up to a total reduction of 95 pct. Subsequently, additional material was obtained with a total thickness reduction of 97.3 pct Standard tensile specimens were prepared from the sheet material with the tensile axis parallel to and at 90 deg to the rolling direction. Tests were run on an Instron testing machine at a strain rate of about 0.050 min-l. Textures were determined by the use of the reflection pole-figure technique. Data were obtained using nickel-filtered CuKa radiation and with the aid of a Siemens pole figure goniometer. The X-ray pole figure studies show an incrzasing development of the texture toward the {110}(112) ideal

Jan 1, 1970

By Gerald Edmunds

THE liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the com- position of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. APPARATUS By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 1 ¾ in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 18 ½ in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By D. R. Parrish, V. J. Berry

Reverse combustion is one thermal method of recovering hydrocarbons from porous undergrortnd formations containing oil or tar. In applying this method, air is introduced via an injection well and the mixture of air and hydrocarbons is ignited in the production well. A combustion zone then recedes toward the injection well, counter-current to the air flow. If the combustion-zorie temperature is sufficiently high, the oil or tar irz place is distilled arid cracked. The hydrocnrhon flows as a vapor to the production well and subsequently is condensed at the surface. Maximum temperature and velocity of morcment arc the two dependent variubles defining the progress of the combustion zone. A theoretical analysis has been made of heat flow in the reverse-comhustion process as.srtrning linear flow in a homogeneous system. The differentirll equatious, which include the oxygen-hydrocar-hon rctrction rate, have been solved numerically. Rescllts indicate that the maximum temperature reached and he cornbustion-zone relocity both increase with an incrense in air-injection rote. Heat loss to surroundings has little effect on the maximum comhustion-zone ten?perature achieved, but it is reflected in a reduced com-bustion-zorzc, velocity. It is also predicted that an increase in the oxygen-hydrocarbon reaction rate results in a reduction in the maximum temperature reached. The calculated results are in agreement with results from reverse-combustion experinments using samples of a tar sand. INTRODUCTION Reverse combustion is one thermal method of recovering hydrocarbons from porous underground forma-tions containing oil or tar.' In applying this method, air is introduced into the underground formation via an in-jection well. In one or more adjacent production wells, the mixture of air and hydrocarbons is ignited at the sand face. The combustion zone thus formed recedes toward the injection well, counter-current to the air flow (Fig. 1). Under certain conditions, the rate of recession of the combustion zone is sufficiently rapid that only a small fraction of the hydrocarbon at any point in the formation is consumed by combustion. If the combustion-zone temperature is sufficiently high, the uncon-sumed oil or tar in place may be partially distilled or cracked. This material then can flow as a vapor with the gaseous combustion products to the production well and subsequently be condensed at the surface. Under other conditions, the combustion-zone temperature may be so low that little, if any, of the hydrocarbon is vaporized. Nevertheless, the viscosity of the hydrocarbon may be reduced enough so that other recovery methods subsequently can be applied to produce oil at attractive rates. The maximum temperature achieved in the combustion zone and the velocity of movement are the two dependent variables defining the progress of the combustion zone. Presumably. knowledge of these factors will permit estimates to be made of oil recovery efficiency, oil and gas producticn rates and average amount of injection air required per barrel of oil recovered. The maximum temperature and combustion-zone vclocity are, in turn, expected to be dependent upon air flow rate, heat losses to surrounding formations, physical properties of the rock and the hydrocarbon. the extent to which the porous formation is saturated with the hydrocarbon, the rate of oxidation of the hydrocarbon and the amount of heat released. It is desirable that the relative importance of each of these factors be understood so that the results of laboratory tests of oil recovery by reverse combustion can be properly interpreted in terms of expected field performance. It is particularly desirable to assess the importance of heat lcsses because these are difficult to control or eliminate

By R. H. Jacoby, M. J. Rzasa

Experimental equilibrium vaporization ratios (K values) were obtained for nitrogen, methane, carbon dioxide, ethane and hydrogen sulfide in two natural gas-absorber oil mixtures and in two natural gas-Elk Basin crude oil mixtures. For each mixture of constant over-all composition, data were obtained at 100°, 150° and 200°F and at various pressures in the range 200 to 5,000 psia. Some effects of composition on the K values were obtained to serve as a guide in choosing K's for engineering calculations on other mixtures. The pressure cell used to obtain the data is a new type and is described here for the first time. INTRODUCTION The phase equilibria of complex hydrocarbon mixtures such as natural gases, crude oils and their mixtures have been studied previously for the purpose of finding equilibrium vaporization ratios for the hydrocarbon constitutents. In a few cases, such non-hydrocarbon.: as nitrogen, carbon dioxide, and hydrogen sulfide were included in the mixture. studied because they occur. in the fluids obtained from petroleum reservoirs. The increasing occurrerce. of these non-liydrocarbon.; antl their growing economic importance. make it necessary to account for them more accurately in engineering calculation.: than is now possible using the meager published data. The available data for non-hydrocarbons may he classified into two groups: namely, binary mixtures of a hydrocarbon and a non-hydrocarbon. and mixtures containing three or more components, only one of which is a non-hydrocarbon. Amon: the former. phase analyses are available for two nitrogen-HC mixtures, tve carbon dioxide-HC mixtures and three hydrogen sulfide-HC mixtures. Data for more complex mixtures are available as follows: Nitrogen-Methane-Pentane'; Nitrogen-Methane-Hexane,'; Nitrogen-Methane-Heptane'; Carbon dioxide-Natural Gas-Natural Gasorline": Carbon dioxide-Natural Gas-Crude Oil". These data have been used generally lor engineering calculations, often with little regard for their precise applicability because data for the non-hydrocarbons in the complex mixtures being dealt with were not available. The use of K values from binary data for calculation:; involving complex mixtures is open to criticism because such K's are not a function of composition and very often show large differences from the K's for the same components in a complex mixture. Thus the effects of composition must be evaluated when obtaining K's for components in complex mixtures. Poettmann and Katz " varied the carbon dioxide content of their mixture.; from about five to ten mol per cent and found substantially no effect on the K values due to this change. This was not surprising since one might expect that changing a minor com-ponent by * three mol per cent would have little effect. It is more important to find the composition change which have the largest effect on the K values. For example. varying the methane or heptanes — plus compositions over a wide rangr may have a large effect on the K'. of all components in the mixture. Interesting data to this effect were obtained by Eilerts and Smith." It was toward these problems that the experimental data presented here were directed. EQUIPMENT The pressure cell used to obtain the data i:. somewhat dif-ferent from those which have been described in the past. Photographs of the equipment are shown in Figs. 1 and 2. Fig. 1 Shows. the front panel: from a .rated position at the right the

Jan 1, 1952

By M. S. Tsai, Y. D. Chuang, H. M. Wu

To contact the commercial OPAP-kerosene solution with CH3OH – H20 solution, we used the appropriate concentration of DOPAP / MOPAP solvent. By using this treated OPAP solvent, uranium can be recovered from wet-process phosphoric acid. Electric DC power is supplied on the dual side of the ion-exchange membrane of a specially designed box-type mixer settler. U(VI) is reduced to U(IV) in the cathode and U(IV) is oxidized to U(VI) in the anode. Uranium is extracted in the cathode by treating it with OPAP solvent. Next the uranium is stripped from the loaded OPAP solvent by concentrated phosphoric acid in the anode. After 300 hours of continuous operation total recovery of uranium is as much as 95%.

Jan 1, 1984

By Denis Yeung, B. H. G. Brady

A hybrid finite element-boundary element code with eight noded isoparametric finite elements and three noded boundary elements is described for plane strain and linear isotropic elasticity. In the direct formulation of the Boundary Flement Method, quadratic variation of geometry and displacements, and linear variation of tractions with respect to the element intrinsic coordinates are used. The boundary element region is treated as a "super-element" in the finite element sense.

Jan 1, 1982

By Raymond Ward

IN the past few years several papers have appeared dealing with different aspects of the oxidation of dilute alloys, especially with respect to the formation of internal oxides or subscales. Subscale has been defined1 as that layer or zone of oxide particles precipitated in a matrix of metallic metal in which the oxide particles are dispersed uniformly and occur by diffusion of the oxygen inward from the metal surface. Alloys composed of a solvent metal more noble than the alloying elements are subject to subscaling or internal oxidation. In these alloys the solute must be present in such quantities that if the alloy is exposed to an oxidizing atmosphere at elevated temperatures, the rate of diffusion of the oxygen into the metal will be greater than the rate of diffusion of the solute outward. There is a composition range of the iron-silicon system that falls into this classification. Knowledge of the nature and rates of oxidation of iron-silicon alloys is of great commercial importance, but very little information of this nature is available. Darken2 recently has made calculations to show the limits of concentration of silicon for which subscales are produced in iron-silicon alloys; however, the main thesis of his paper was to analyze and to explain the already existing data. The purpose of this paper is to present the effect of com position, temperature, time, and atmosphere on the type of scale-metal layer obtained and to give some qualitative indication of the effect of these variables on the rates of oxidation. Since this paper is a study of silicon steels that are available commercially, extremely low-silicon and high-silicon alloys are not included. EXPERIMENTAL PROCEDURE The alloys used in the experiment were taken from heats of silicon steel that ranged in analysis from 0.70 to 5.8 per cent silicon. This composition range takes in most of the commercial silicon steels. In Table I are listed the compositions of alloys used. Other than iron and silicon, the alloys normally contained approximately the following impurities: carbon, 0.03 per cent; manganese, 0.07; phosphorus, 0.008; sulphur, 0.02; copper, 0.07; tin, 0.01, and from nil to a trace of chromium, nickel and copper. All of the alloys used were melted in open-hearth furnaces, except where otherwise noted, and were hot-rolled to 0.100-in. plate. Samples approximately 1/2 in. square were then cut from these materials. So that the surface conditions of the samples used for oxidation would be standardized, each sample was ground through 000 emery paper immediately before oxidation. Two different techniques were employed in carrying out the oxidizing treatments. One consisted simply of heating the samples with free access to air. In this treatment the samples were set on edge on a refrac-

Jan 1, 1945

By Cyril Stanley Smith

Jan 1, 1949

By Cyril Stanley Smith

Jan 1, 1949

By C. R. Forbes, J. C. Barton

Many different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. Description" of Bits Tested 'I'he 4-point bits were the usual shaped bits commonly made on the Leyner sharpener, with 14' taper on the wings and a 90" angle between cutting edges. Some tests were run at 85 Ib. pressure with a 4-point bit made with a 50 taper on the wings; this bit was formed with the Carr bit dies. The 6-point bits were the usual shaped bits made on the Leyner sharpener. The Carr bits were made with a 5º taper and an angle of 100" between cutting edges.

Jan 1, 1918

By P. E. Baker

Approximate solutions are presented for the heat-flow equations in a loss-free linear system with a moving source and with heat transfer by convection and conduction, representing in situ combustion in an oil reservoir. The rate of heat generation and the velocity vf of the source (flame front) are assumed constant. A cold front or convection front caused by the cooling effect of in-jected air develops behind the flame front and moves with velocity vc, which is determined by the thermal properties of the air and rock. Because of thermal conduction the fronts are not sharp; i.e., they do not represent temperature discontinuities. The following solutions apply after a sufficiently long time. where Q is heat generated per unit volume of formation, k is thermal conductivity, CF is volumetric heat capacity, a is thermal diffusivity, and subscripts 1 and 2 refer to values behind and ahead of the flame front, respectively. The parameter CF2 is contained in v . Te is initial reservoir temper- . C2 e ature and air-injection temperature. Other mathematically possible solutions are presented. The different solutions result from the use of different values for various physical parameters. The solution just presented is thought to be most commonly applicable. INTRODUCTION In this paper, approximate analytical expressions are derived for the temperature profile developed in the underground combustion method of oil recovery. A qualitative description of the process may be found in a paper by Tadema.1 The flame front is regarded as a moving source with a constant rate of heat generation. Heat transfer is by conduction and convection. Previous publications, of which a few are cited here, 2-5 have also attacked this problem and have presented solutions pertaining to different methods of approximating or idealizing the process studied. The present paper also treats an idealized case: linear flow is assumed for heat and fluids, and vaporization and condensation effects are neglected. The results obtained are similar to those derived by Bailey and Larkin,3 but are obtained by an entirely different procedure. The method used here should give considerably greater insight into the physics of the in situ combustion process. Four types of cases are considered, distinguished by thermal and fluid-flow properties of the system. A constant rate of heat generation and constant rate of flame-front advance are assumed. Flame-front temperature is determined for each case using a heat balance which involves the entire temperature profile. The applicability of the different solutions to real systems is discussed after they are all presented. Again, this is done for the purpose of understanding better the physics of the process. Consideration of the nonapplicable solutions and of the reasons for their not applying is significant. In a paper by Cooperman,4 the only case solved is one considered here as not applicable. Fluid flow, as such (pressures, saturations, oil recovery, etc.), is not treated. This subject has been covered in a paper by Wilson, et al.6 Also, we are not concerned with requirements for continuance of the process; we only attempt to determine the temperature history for cases where the process has continued for some time. PHYSICAL SYSTEM AND APPROACH TO PROBLEM A linear flow (heat and fluid) system is assumed and the x-axis is taken parallel to the flow direction. The combustion zone (flame front) is vertical,

Jan 1, 1902

New Products Equipment

Jan 8, 1951

By W. M. Bertholf

To establish the minimum or break-even efficiency of a preparation plant it is necessary to determine the ratio of production costs per ton of run-of-mine coal to sale price per ton of clean coal. This ratio is then divided by the percentage of plant recovery. Assume, for example, that washability data indicate that 80 pct of the run-of-mine coal may be recovered as clean coal selling for $5.50 per ton. If the same plant incurs $4.00 per ton mining costs and $0.25 per ton preparation costs, the cost to sale price ratio would be 4.25/5.50, or 77.3 pct. Since the plant is capable of recovering 80 pct of the run-of-mine coal the minimum plant efficiency would be 77.3/80, or 96.6 pct. If the plant efficiency were increased to 100 pct the limit on preparation costs would be increased to $0.40. Therefore, the washing operation must be accomplished at a cost of $0.25 to $0.40 per ton and the efficiency must be 96.6 pct or higher. By plotting a curve of efficiency vs preparation costs and taking into consideration the plant cost, feed rate, operating costs, and yields of the various flowsheets it is possible to select a financially sound process. Table I classifies preparation processes according to their nature of separation. It must be remembered that what is thought to be ideal does not always prove practical under actual operation. An outstanding example is the work done on the plunger-type jig. It was determined by the law of equivalence that this unit could treat satisfactorily only sizes differing by no more than a ratio of 2. Yet these same plunger-type jigs are successfully treating sizes considerably greater than this ratio.

Jan 12, 1957

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Position open as assistant superintendent at a steel plant. Practical experience in the manufacture of crucible and open-hearth steel and heat treatment of steel and alloy steels required. This position offers an excellent future. No. 9. A company in Virginia desires a man with experience in Western mines to act as superintendent of its pyrite mine. No. 15. Position open as instructor at a University in Middle West to teach the mechanical side of mining, such as hoisting, haulage, drilling, and mine surveying. Salary, $1,500 to $1,800. No. 16. Experienced amalgamator wanted at a mill in Ivory Coast, Africa. An American speaking French preferred. No. 18.

Jan 5, 1914