Search Documents

[NUMERICAL CODE TO MAPS (Region Listed in Roman Numerals after Each Petroleum Section) 1 Alaska 2 Arizona 3 Black Hills 4 Boston 5 Carlsbad Potash 6 Central Appalachia 7 Chicago 8 Cleveland 9 Colorado 10 Columbia 11 Connecticut 12 Delta (VIII) 13 Detroit 14 East Texas (VI) 15 El Paso 16 Gulf Coast (VII) 17 Kansas (IX) 18 Lehigh Volley 19 Mid-Continent (IX) 20 Minnesota 21 Montana 22 Nevada 23 New York]

Jan 1, 1961

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By M. B. Standing, D. L. Katz

Equilibrium data are reported on the composition and densities of coexisting vapor and liquid phases as a function of Pressure and temperature for four hydrocarbon systems prepared from crude oil and natural gas. The data were observed over a range of pressures from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35&apos; to 250°F. The compositions of the hydrocarbon systems were such that the critical temperatures of the mixtures were lower than the range of the investigation. Under these conditions, it is shown that the composition of the systems has a marked effect upon both the absolute value of the equilibrium constants and the change of the constants with pressure for the several components comprising the system. From weight-balance considerations, it has been possible to construct the partial phase diagram of a mixture of a 49.9" A.P.I. crude oil and natural gas having a gas-oil ratio of 3660 cu. ft. per barrel. Descriptions of the apparatus used, the analytical procedure, the material used, and the equilibrium measurements are included. A knowledge of the physical behavior of naturally occurring hydrocarbon mixtures is fundamental to the treatment of many problems in the production, transportation and rehing of petroleum. The recent discoveries of pools having formation pressures up to 7500 lb. per sq. in. and higher, and the development of full-scale equipment to operate at pressures of 5000 lb. per sq. in. or more have greatly increased the need for knowledge of the composition, temperature, pressure and density relationships of coexisting vapor and liquid hydrocarbon phases. The following paper presents the results of investigations upon 22 mixtures of natural gas and crude oil of known com~o~itio~ that had been brought to equilibrium under controlled conditions of temperature and pressure. Data are presented upon the densities and compositions of the coexisting vapor and liquid phases for four different systems containing hydrocarbon material having boiling points from minus 2 5S°F. to well over I000 F. The data were observed Over a pressure range from Iooo Ib. per Sq. in to 8220 lb. Per sq. in. and a temperature range from 35&apos; to 2 50°F. The accepted method of computing the physical relationship between two coexisting phases of a hydrocarbon mixture is by use of the "equilibrium constant" K as proposed by Souders, Selheimer, and Brown. definition,

Jan 1, 1944

By M. B. Standing, D. L. Katz

Equilibrium data are reported on the composition and densities of coexisting vapor and liquid phases as a function of Pressure and temperature for four hydrocarbon systems prepared from crude oil and natural gas. The data were observed over a range of pressures from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35&apos; to 250°F. The compositions of the hydrocarbon systems were such that the critical temperatures of the mixtures were lower than the range of the investigation. Under these conditions, it is shown that the composition of the systems has a marked effect upon both the absolute value of the equilibrium constants and the change of the constants with pressure for the several components comprising the system. From weight-balance considerations, it has been possible to construct the partial phase diagram of a mixture of a 49.9" A.P.I. crude oil and natural gas having a gas-oil ratio of 3660 cu. ft. per barrel. Descriptions of the apparatus used, the analytical procedure, the material used, and the equilibrium measurements are included. A knowledge of the physical behavior of naturally occurring hydrocarbon mixtures is fundamental to the treatment of many problems in the production, transportation and rehing of petroleum. The recent discoveries of pools having formation pressures up to 7500 lb. per sq. in. and higher, and the development of full-scale equipment to operate at pressures of 5000 lb. per sq. in. or more have greatly increased the need for knowledge of the composition, temperature, pressure and density relationships of coexisting vapor and liquid hydrocarbon phases. The following paper presents the results of investigations upon 22 mixtures of natural gas and crude oil of known com~o~itio~ that had been brought to equilibrium under controlled conditions of temperature and pressure. Data are presented upon the densities and compositions of the coexisting vapor and liquid phases for four different systems containing hydrocarbon material having boiling points from minus 2 5S°F. to well over I000 F. The data were observed Over a pressure range from Iooo Ib. per Sq. in to 8220 lb. Per sq. in. and a temperature range from 35&apos; to 2 50°F. The accepted method of computing the physical relationship between two coexisting phases of a hydrocarbon mixture is by use of the "equilibrium constant" K as proposed by Souders, Selheimer, and Brown. definition,

Jan 1, 1944

By J. R. Long, T. R. Graham, R. S. Dean

FOLLOWING the development of elec¬trolytic manganese production by the Bureau of Mines, an extensive program was planned to study the character of this high-purity product and its possible utilization in various alloy combinations. Previous work reported in the literature concerning alloys containing substantial amounts of manganese dealt largely with material prepared from relatively impure grades of the metal, and in many instances the impurities thus introduced did not permit true evaluation of manganese as an alloying element. One phase of the Bureau&apos;s program included a general review of the system and the establishment of the physical properties of copper-manganese-zinc alloys, using electrolytic manganese, and with particular emphasis directed to com¬positions within the alpha solid solution area. A number of reports of the work on alloys in this system, giving specific data concerning the equilibrium system and some of its alloys, have already been published. One study1 established the alpha solid solution area at various temperature levels and composition ranges up to 50 pct manganese. Other investigation reports presented the properties of selected alloys; namely, a 65 pct copper, 10 pct manganese, 25 pct zinc alloys&apos; a sensibly white manganese brass composed of 70 pct copper, 20 pct manganese, 10 pct zinc,3 and a series of alloys with a constant copper content of 60 pct and 5 to 25 pct manganese, balance zinc.4 In these reports tensile properties as influenced by cold-working and subsequent annealing were given in detail. Additional data are now available on other alloys of the alpha region up to 50 pct manganese, and these, together with previously published information, are sufficiently complete to establish the relationship between properties and composition for this portion of the ternary system. The present report is a summary of the tensile properties of wrought alloys in the form of sheet and rod stock. The summary is necessarily limited to data for only one condition of cold-work and a single annealing temperature, since a complete exposition of all the data available would be too extensive for this presentation. Nevertheless, it is possible to make a reasonable approximation of the tensile properties in other conditions of cold-working and annealing by a correlation of the data previously presented on specific alloys and the data given here.

Jan 1, 1947

By F. Forward, H. Veltman, A. Vizsolyi

Activities of oxides in the ternary FeO-MnO-SiO system are calculated from data on the binaries, using the Gibbs -Schuhmann method. These activity data are used, together with thermodynamic relations, to calculate the contents of oxygen, silicon, and manganese in liquid iron, and the composition of the corresponding oxide phases in equilibrium with it. Excellent agreement was found between calculated and experimental metal compositions, indicating that thermodynamic methods, such as those presented, can supply useful data on slag-metal equilibria, and are therefore capable of wider application. When molten steel containing oxygen is treated with a deoxidizer, the product of the reaction is composed of the oxides of the deoxidizing elements together with more or less iron oxide. This assemblage of oxides is presumably very close to equilibrium with the melt since it is formed directly from elements dissolved in it. Therefore, it is likely that metal analyses corresponding to a given oxide phase composition are calculable with considerable precision where sufficient information is available on activities in both phases. The present study was made to test this hypothesis in the case of deoxidation by silicon and manganese. Here experimental data on the relationship among oxygen, silicon, and manganese in the metal phase are available, as are activity data for the MnO-SiO2, FeO-SiO2, and FeO-MnO binary systems. A further objective was to demonstrate in a specific example how gaps in the data may be filled by judicious interpolation, and how the Gibbs-Schuhmann method is applied to obtain activities in ternary systems. The rigorous derivation of the latter, requiring considerable facility in handling partial differential equations, tends to mask the real simplicity of the method, and repel the very engineers and experimenters who would benefit the most from its use. I) GENERAL PROCEDURE Deoxidation of steel with silicon and manganese results in the formation of two phases, metal and oxide. The number of components is four—Fe, Mn, Si, and 0. The phase rule then gives the number of degrees of freedom: If temperature and pressure are fixed, 2 deg of freedom remain. Consequently, it suffices to fix the concentration of two of the components of the system for all the concentrations to be determined and, at least in principle, calculable. The practical problem is then to discover a straightforward method of calculation with a minimum of trial and error solutions. The type of reactions to be dealt with are like the following: Si (in steel) + 2 O(in steel) = SiO2(in oxide phase) The standard free energy of this reaction is readily obtained from the literature, so that the equilibrium constant can be calculated by the expression: Since the metallurgist is concerned with percentages rather than activities, a real solution requires information that will permit activities to be converted to concentrations. This information is fairly adequate for the elements dissolved in molten steel, but is not available for the FeO-MnO-SiO2 oxide system. Therefore, the first step in this study was to find the relation between activity and concentration for the three oxides making up the system. The next step was the calculation of slag and metal compositions that are in equilibrium with one another. As shown by the phase rule, it is sufficient to assume the values of two composition variables in order to calculate the rest. But which two are picked makes a vast difference in how difficult the calculation turns out to be, so that it is necessary to make preliminary trial of several routes to find the easiest one. A convenient method is to begin with the slag, and to pick FeO concentration and that of one of the other oxides. Starting with the relation between oxygen dissolved in the liquid steel and FeO in the slag permits a good first estimate to be made of the oxygen content of the steel in equilibrium with FeO, because the iron content being fairly close to 100 pct, Fe has an activity close to unity. Using this first estimate of oxygen activity, approximate values of the manganese and silicon contents of the melt are readily calculated from the appropriate equilibrium constants. A minor correction for the depar-

Jan 1, 1963

By Wm. A. Haven

As soon as the likelihood of American participation in the war was established, and in spite of the fact that we can produce almost as much as all other countries combined, the demand for prompt deliveries of iron and steel products from American factories began to exceed their utmost capacity, and, after fifteen months of practically full operation, has continued to do so. Therefore, it would seem worth while to review some of the aspects of the supply and demand for steel as well as the efforts that are being made to bring them into balance. It is still being debated as to whether the situation should be defined as a real shortage that will persist through the emergency period or as a temporary one than can be relieved by less drastic measures than a Government-sponsored program of expanding existing plants and building new ones.

Jan 1, 1942

By J. A. Bownocker

THE production of oil in Ohio, in 1924, was characterized by no marked or surprising change. Low prices and the absence of promising territory made the year quiet. As is well. known, Ohio has reached a state of "settled production," and the most that can be expected for the ensuing few years is to maintain the output at approximately the present figure 1921 7,335,000 1922 6,781,000 1923 7,085,000 Geographically, the Ohio fields may be divided into three areas, each of which gets its main supply of oil from a different stratigraphic horizon.

Jan 3, 1925

By J. A. Bownocker

THE production of oil in Ohio, in 1924, was characterized by no marked or surprising change. Low prices and the absence of promising territory made the year quiet. As is well known, Ohio has reached a state of "settled production," and the most that can be expected for the ensuing few years is to maintain the output at approximately the present figure 1921 7,335,000 1922 6,781,000 1923 7,085,000 Geographically, the Ohio fields may be divided into three areas, each of which gets its main supply of oil from a different stratigraphic horizon.

Jan 3, 1925

By R. Taggart, J. W. Barton, G. R. Purdy, J. G. Parr

The constitution and mechanical properties of heat-treated alloys containing up to 10 pct* Ni in Ti have been investigated. The effects of quenching and of various isothermal treatments ale described, and C-curves are presented. The production of the precipitated and the martensitic hexagonal phases on quenching is discussed. MARGOLIN, Ence, and Nielsenl have determined the titanium-nickel phase diagram. A study of the transformations in gas-quenched and tempered powder specimens was made by Polonis and Parr.&apos; Some isothermal transformation work was carried out by Margolin and ~unshah, who determined transformation curves for 4 and 6 wt pct alloys, while Robinson et al.investigated the formation of the w phase in a quenched and tempered alloy, Margolin and Bunshah showed that while a martensitic transformation could be obtained on quench- ing thin sections of a 4 wt pct alloy, a 6 wt pct alloy precipitated a nonmartensitic phase. The present investigation was undertaken to obtain more information on the transformations in quenched, quenched and tempered, and isothermally transformed lump specimens of alloys containing up to 10 pct Ni. Isothermal transformation curves have been determined for 7 and 10 pct alloys and cooling curves have been obtained for quenched alloys containing up to 7 pct Ni. The mechanical properties of 2, 5, and 10 pct alloys were studied, with the object of relating properties to microstructures. EXPERIMENTAL METHODS Alloys containing up to 10 pct Ni were prepared from sponge titanium and spectrographic standard nickel by levitation-melting and chill-casting in a split copper mold. The 5 and 10 pet alloys were prepared from sponge Ti having an as-melted hardness of 115 Vpn. The other alloys were made from a sec-

Jan 1, 1961

By Richard F. Miller

Recent studies of creep have made it apparent that plastic deformation may occur in metals under stresses less than the elastic limit as determined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapselll said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was determined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instruments by A. W. Hanson4 on zinc and by Podaschewsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc. AppaRatus The creep-testing apparatus developed for this work is shown in Figs. 1 and 2. The extensometer A is sensitive enough to detect changes in length of 3.3 X 10~6 in. per in., and yet can be used into the plastic range without injury to the apparatus. The specimen,

Jan 1, 1936

By Harrison Souder

THE object of this paper is to bring to. the notice of engineers a safety detonating fuse by the use of which misfires in blasting may be eliminated and safety in blasting operations promoted. This new detonator is a French invention and is known as Cordeau detonant or detonating fuse and is sold under the name of Cordeau-Bickford. It consists of a lead tube 5 to 6 mm. in diameter, filled with trinitro-toluene. While applicable to all classes of mining it will appeal especially to those who have to do with deep-hole blasting in open-cut clines or quarries, or any operations where a large number of holes are to be shot at one time. Since the introduction of the deep-hole blasting in the Cornwall iron mines, much trouble has been experienced from misfires and many experiments were made to determine the best and safest method of blasting. Before the introduction of the detonating fuse it was found that to insure the best results, two or more high-power electric exploders, not less than No. 6, with specially insulated conductors, should be placed in each hole; the holes wired in parallel, and for a large number of holes the current to be supplied by a live wire to the bus or lead wires at about the middle of the bench. The voltage in general use is 110 to 220, but as our material is a magnetic iron ore and the holes are generally damp, we found it advisable to reduce this to about 30 volts to prevent short circuits. A No. 7 or No. 8 special insulated detonator was adopted. But with the best of care and attention to the minutest detail, we were not able to eliminate occasional misfires and the consequent ever present danger of accidents.

Jan 10, 1914

By F. N. Lathe

In 1882, The Arizona Copper Co., Ltd., acquired producing copper mines at Metcalf and Morenci (locally called Longfellow). Metcalf is situated a distance of 7 miles, and Morenci a distance of 6 miles from the general office of the company at Clifton, Ariz. A reduction works with five blast furnaces was built in the center of the town of Clifton in 1884 and operated until January, 1914. Concentration of oxidized ores was begun in 1890-1891, in a mill built adjoining the smelter, and id October, 1893, a leaching process was started for treating tailings from the oxide mill. A sulphide concentrator with 300 tons capacity was built at Clifton and started treating chalcocite ores in July, 1896. This was the first mill to treat low-grade copper-siilphide ores successfully. Another concentration mill for sulphide ores was erected at Morenci in 1900. The sulphide mills are now being remodeled to treat ores by concentration and flotation, with a capacity of 4,000 tons at Morenci and 500 tons at Clifton. The leaching plant has not been running since September, 1914. The average yearly production from this company&apos;s mines and reduction works from 1885 to date has been: Pounds 10 years ended 1894................................... 6,864,902 10 years ended 1904................................... 20,439,614 10 years ended 1914................................... 32,665,905 Part of year 1915, to Sept. 12........................... 30,206,106 4 months of 1916, to June.............................. 15,964,840 June, 1916........................................... 4,900,000 Construction on a new smelting plant was started in February, 1912, and finished in February, 1914. In the Transactions, vol. 49, E. Horton Jones published "Unit Construction Costs from the New Smelter of the Arizona Copper Co., Ltd.," which fully describes the construction of this plant, with details of costs.

Jan 1, 1917

By John T. Galey

In all, 210 wellst were completed in southwestern Pennsylvania during 1939, which is 59 more than were drilled during the preceding year. Of this number, 137 were gas wells, which is a considerable increase from the 81 completed during 1938. Only 25 oil wells were completed, as against 28 in the previous year, and 28 dry holes, 6 more than last year. Shallow Development—Gas The increase in the number of gas wells is largely the result of a search for additional gas in Armstrong and Indiana Counties. Although a considerable number of wells were drilled in the latter county, the majority of them produced less than 100 M cu. ft. initial open flow. In Armstrong County, a new pool was opened in Cowanshannock township, producing from the third Bradford sand. Several large wells were obtained there, one of which produced an initial of nearly 12 million cu. ft., with a reservoir pressure of 1100 Ib. However, the productive area has been fairly well outlined by further drilling and shows that the pool covers only about 800 acres. The sand is 20 to 30 ft. thick, and probably has 5 to 6 ft. of pay. Thus this reserve is not an important one. Several wells were found in Menallen township, Fayette County, where the Big Injun sand has been having a play for the past three years, but the activity there is much less than a year ago. Oil On the west side of the Bradford sand gas pool, Cowanshannock township, Armstrong County, a well was drilled which flowed 100 bbl. the first day from the Tiona sand. The probability is that this well is a freak, as the Tiona has been drilled within a fairly close distance on every

Jan 1, 1940

By John T. Galey

In all, 210 wellst were completed in southwestern Pennsylvania during 1939, which is 59 more than were drilled during the preceding year. Of this number, 137 were gas wells, which is a considerable increase from the 81 completed during 1938. Only 25 oil wells were completed, as against 28 in the previous year, and 28 dry holes, 6 more than last year. Shallow Development—Gas The increase in the number of gas wells is largely the result of a search for additional gas in Armstrong and Indiana Counties. Although a considerable number of wells were drilled in the latter county, the majority of them produced less than 100 M cu. ft. initial open flow. In Armstrong County, a new pool was opened in Cowanshannock township, producing from the third Bradford sand. Several large wells were obtained there, one of which produced an initial of nearly 12 million cu. ft., with a reservoir pressure of 1100 Ib. However, the productive area has been fairly well outlined by further drilling and shows that the pool covers only about 800 acres. The sand is 20 to 30 ft. thick, and probably has 5 to 6 ft. of pay. Thus this reserve is not an important one. Several wells were found in Menallen township, Fayette County, where the Big Injun sand has been having a play for the past three years, but the activity there is much less than a year ago. Oil On the west side of the Bradford sand gas pool, Cowanshannock township, Armstrong County, a well was drilled which flowed 100 bbl. the first day from the Tiona sand. The probability is that this well is a freak, as the Tiona has been drilled within a fairly close distance on every

Jan 1, 1940

By R. W. Harper, M. C. Fuerstenau, J. D. Miller

Data were obtained with hematite with octyl hydroxamate and oleate as collectors to determine the mechanism of collector adsorption and also to establish the roles that conditioning time and temperature assume in this system. The presence of hydroxy complexes of iron are apparently necessary for chemisorption of collector to occur, and it appears as if extended conditioning times and elevated temperature promote greater dissolution of the mineral and hence greater concentrations of hydroxy complexes. Data were also collected with two natural hematitic ores. With one ore that was ground to 70% - 15u, an addition of 0.4 lb per ton hydrox-amate resulted in a final concentrate recovery of 86% at a grade of 64% iron. Satisfactory concentrate grade could not be obtained with fatty acid under these conditions. The effect of conditioning time prior to the addition of collector was also examined with another ore. When the ore was conditioned for 3 min, 19% of the iron was recovered in the concentrate at a grade of 67% Fe. With a conditioning time of 7 min, 73% of the iron reported to the concentrate at a grade of 62% Fe. These products were obtained with an addition of 0.2 lb per ton hydroxamate. This ore also responded well to flotation with fatty acid. The use of potassium octyl hydroxamate as a collector for iron oxide has been the subject of an earlier study.1 From this initial study, it was suspected that hydrolysis of surface ferric iron was involved in collector adsorption. More recent work in other systems has shown that slight mineral dissolution, followed by hydrolysis of cations common to the mineral lattice, is apparently necessary, and that adsorption of these hydroxy com- plexes probably occurs prior to the adsorption of collector. In view of these facts, work has been continued on the hydroxamate-hematite and oleate-hematite systems to gain better insight into the mechanisms of collector adsorption on iron oxide. Microflotation experiments in conjunction with infrared analysis were used in this regard. In addition it was felt necessary to establish more clearly the responses that can be obtained from natural ores when hydroxamate is used as collector as compared to those obtained when fatty acid is used. Experimental Materials and Techniques Pure potassium oleate, potassium octyl hydroxamate, synthesized from hydroxylamine hydrochloride and methyl octanoate, and a distilled Tall Oil were employed as collectors. Conductivity water was used in the

Jan 1, 1971

By S. R. Maloof

In 1945, Hollomon&apos; showed that after plastic yielding and prior to necking under simple tension, both ferrous and nonferrous materials are approximated by an equation of the following form: where, a = true stress K = strength coefficient 5 = true strain n = strain hardening exponent If a material is stress free, a plot of log o vs log 6 would be expected to be a straight line, the slope of which is the strain-hardening exponent (n) and the intercept on the ordinate axis for 6 = 1. is the logarithm of the strength coefficient K. It can be easily shown that the strain-hardening exponent in the above equation is equal to the total uniform elongation prior to necking. Thus, one can determine the total uniform elongation prior to necking from such a plot and, as pointed out by C. W. MacGregor, 2 it is the amount of strain prior to necking which determines the extent to which a material may be deep drawn. In the view of the current interest in the fabrication of beryllium shapes, it was thought that a knowledge of the strain-hardening exponent of cross-rolled beryllium sheet would be of general interest. Load-strain data after yielding and prior to necking was taken from the work of Greenspan,3 converted to true stress and true-plastic strain, and plotted on log-log paper as shown in Fig. 1. The value of Young&apos;s modulus E for beryllium was taken as 43 . l06 psi. The slope of this plot gave a value of 0.212 for the strain-hardening exponent (n) and the intercept on the ordinate axis a value of 105,000 for K. The total uniform elongation is thus 21.2 pct, in excellent agreement with the value estimated by Greenspan (about 20 pct). Furthermore,

Jan 1, 1960

By G. W. Josephson

VIRTUALLY every year inventors find one or more startling new uses for one of the varied products of the nonmetallic mineral industries. For example, in November a major step toward positive control of rainfall was made when an experimenter converted a cloud to snow by dropping a few pounds of solid carbon dioxide into it. Other examples of ingenuity in the development of markets and production methods are noted in the following pages. For most of the industrial mineral products one of the outstanding features of 1946 has been the high level of production. There are exceptions, such as quartz crystal and lithium, whose production capacity during the war outgrew current peacetime needs, but they are few. Some technical men point out that this prosperity is not an unmixed blessing to technologic progress, because so much effort must go into day-to-day production problems that relatively little opportunity is left for the pursuit of new developments.

Jan 1, 1947

By J. J. Oberly

WHILE examining lineage boundaries in germanium single crystals as described by Vogel et al.,&apos; patterns of conical etch pits were noted which reveal interesting properties of dislocations. The crystals were grown by pulling in the <100> direction, and (100) surfaces perpendicular to the growth direction were etched 4 min in a mixture of 6 cu cm HF, 10 cu cm HNO3, 6 cu cm acetic acid, 3 drops Br,. Lineage boundaries extended in any direction, but favored the <110> direction. The patterns which were noted first were composed of two or three etch pits arranged symmetrically about the lineage boundary, so that the doublets were spaced equally on either side of the boundary line and the triplets had their center pit on the boundary line. The triplets occurred less often than did the doublets; occasionally combinations were found. Two such combination patterns are shown in Figs. 1 and 2. The orientation of the patterns was determined approximately by subsequently etching the same surfaces in a mixture of 5 cu cm HF, 5 cu cm super-0x01, and 20 cu cm distilled water which produced nearby random square etch pits having edges in the <110> direction. In all cases, the axis of symmetry was <110>, being parallel to the etch-pit edges. Several successive lapping and etching operations showed that the patterns tended to continue through the crystal in the <100> direction, but eventually changed or vanished. It can be seen in both photographs that the pits in the patterns are much further apart than the pits in the adjacent section of the lineage boundary. In Fig. 1, the 10 pits of the pat-

Jan 1, 1955

By John Wulff, J. H. Hollomon

SERVICE failures in brass condenser tubes are often due to corrosion. One of the commonest types of corrosion reveals a surface structure of redeposited copper.1 The study of the effect of alloy addition agents in preventing this kind of corrosion has received impetus from the extensive publication of Bengough and May.2 The mechanism of such inhibition gauged from immersion corrosion,&apos; cell corrosion,&apos; and electrolytic potential&apos; measurements is controversial. This controversy may be attributed in part to a lack of definite knowledge5 of the actual nature of the initial films formed in corrosion experiments. In our own corrosion work on copper and 70-30 brass this lack became apparent and necessitated an examination of surface films by X-ray and electron diffraction methods. The present paper is but an introduction to the subject of inhibition and reports the structure of films formed in active corrodents. EXPERIMENTAL PROCEDURE The arsenical coppers and brasses used in this investigation were made by one of the writers* in the plant of the Revere Copper and Brass Co. at Rome, N. Y. Standard commercial melting practice was followed. O.F.H.C. copper and electrolytic zinc were used and all arsenic additions were made by additions of a master copper alloy. The final analyses are given in Table I. Likewise, the extrusion, cold-rolling, and intermediate anneals employed followed standard usage. Final heat-treatments were given to all materials to produce a similar grain size (0.035 to 0.045 mm. for brass and 0.015 to 0.025 for [ ] copper) for the alloys containing various percentages of arsenic. Samples ¼ by ½ by ¼ in. were cut from sheet material resurfaced and finished with 0000 metallographic papers. The surfaces were all degreased in alcohol and benzine before immersion. After immersion in the corrodent, they were washed gently in tap water, dipped first in alcohol and then in pure benzine and allowed to dry in the diffraction apparatus. The reflection electron diffraction apparatus used has been described by Burwell

Jan 1, 1941