Search Documents

By O. I. Deschon, Ralph Arnold

Deep drilling was the keynote of the more important developments in the North Rocky Mountain region during 1929, with Montana recording the most important achievement through discovery of three new oil fields. Alberta produced 1,000,000 bbl. of 74 gravity naphtha, showing a considerable gain over 1928, developed a commercial oil pool in Turner Valley and extended that field 8 miles southward. Wyoming's discovery field was deepened to a second producing horizon, giving impetus to deeper drilling, and practically every Wyoming oil field will have a deep test either this year or in the near future. Whereas Montana prospecting has been confined to the shallow plains structures, since the discovery of Kevin-Sunburst field, the coming year will see an active search for new oil and gas pools in sharp-dip structures, following the success of prospecting in the Sweetgrass Hills during 1929. A dozen or more structures have been mapped in North Central Montana, several of these straddling the Alberta border. Four structures tested thus far have all shown commercial oil or gas or both. Sweetgrass Hills The first important development in the Hills area was the Rogers-Imperial gasser, which had an initial of 51,000,000 cu. ft. of dry gas per day, with a rock pressure of 1080 lb. This well is located on a sharp nose running north from the hills into Alberta. Several wells drilled by independent operators on the American side, on the west flank of reserve structure, have developed a total open flow capacity of 30,000,000 cubic feet. The third structure tested in the Hills area is known as Bears Den, where commercial oil was found at the base of the Cretaceous at 2470 ft. The existence of oil in three lower sands has been established by two wells on the top of the structure, these two wells finding gas flows of 10,000,000 and 15,000,000 cu. ft., respectively, in the horizon where

Jan 1, 1930

By S. R. B. Cooke, Y. S. Kim, I. Iwasaki

lron oxides or the gangue minerals of iron ores can be made to float, depending upon the choice of collector. The selectivity of the separation is controlled by the accompanying chemical and operating conditions. In this report the findings on the general flotation characteristics of magnetite are summarized and the results are compared with those obtained for other iron oxides. Depending upon the choice of collector, either the iron oxides or the gangue minerals of iron ores can be made to float, the selectivity of the separation being controlled by the accompanying chemical and operating conditions. The mechanism by which a collector exerts preferential affinity for either group of minerals has been a subject of extended discussion. Previous investigations on the electrokinetic properties and flotation characteristics of hematite,' goethite,2 and quartz3 have demonstrated the electrical nature of the interaction of the collector with these oxide surfaces; anionic collectors are effective on positively charged surfaces and cationic collectors on negatively charged surfaces. Thus, from the differences in the electrokinetic properties of the above-named oxides, a theoretical basis has been provided for their separation by some typical collectors. Examination of the results reported for hematite and goethite shows that their electrokinetic properties and flotation characteristics are remarkably similar. It is of considerable interest, therefore, to examine similar information for magnetite, another common iron oxide, in order to consolidate the flotation characteristics of the three principal minerals of oxide iron ores. Such information is practically significant in the up-grading of both natural and artificial mag- netite produced from taconite, and in the treatment of partially oxidized magnetite ores. Information on maghemite and lepidocrocite, polymorphs of hematite, and goethite, respectively, is also of some theoretical interest in ascertaining the effects of crystal structure and of hydration in the iron oxide group. This article reports the findings on the general flotation characttxistics of magnetite, and compares the results with those obtained for other iron oxides. Experimentally, tlhe surface properties of magnetite were investigated by electrophoresis, and by measurement of the aclsorption of some typical flotation collectors. Its flotation behavior was tested by contact angle measurements and by simple flotation tests using a modified Hallimond tube. The basic information thus gathered was shown to be directly applicable to the interpretation of the results of batch flotation tests made on an artificial mixture of magnetite and quartz. EXPERIMENTAL MATERIALS Magnetite: Magnetite concentrate from Port Henry, N. Y., was further purified by fine crushing and magnetic separaiion, and was used throughout this investigation. For flotation tests the 150/200 mesh fraction was iso1ated and was cleaned by leaching briefly with warn 0.1 N HC1 followed by repeated washing with demineralized water. The final sample analyzed 71.71 pct Fe, 22.37 pct Fe" and 0.47 pct insoluble, and was stored in demineralized water. For e1ectrophoresis and adsorption measurements, the —400 mesh fraction of the magnetite concentrate was ground dry in a pebble mill. The surface area of the ground sample, as determined by the gas permeability method, was 70,000 sq cm per g. Since artificial magnetite has been reported to possess somewhat different physical properties than those of natural magnetite, it also was briefly examined. Preliminary flotation tests on a sample of artificial magnelite, prepared by reducing Brazilian hematite in a C0/CO2 mixture and analyzing 71.94 pct Fe and 23.78 pct Fe'', gave, however, nearly identical results with those using natural magnetite. It was concluded that artificial magnetite behaves similarly to natural magnetite. Samples which had been magnetically separated showed a tendency to cluster together due to residual

Jan 1, 1962

By G. P. Chatterjee

HARDNESS is one of the most common properties of metals and alloys but is one of the most difficult to define or express in terms of the fundamental units. In the Brinell or Vicker's hardness test, the hardness number N is defined as N = L/A where L is the load in kilograms and A is the area in mm'. This does not necessarily imply that a pressure of N kilograms per mm2 actually acts on the specimen.' It is essential that for a true comparison of hardness values the angle of indentation be kept constant,' a which is not done in the Brinell test. For this and other reasons, the Brinell hardness value is not based on a satisfactory physical concept.' The concept of hardness based on the work done per unit volume of indentation3-6 offers a simple and scientific definition. An attempt has been made here to develop this concept (at constant angle) and to compare the values so obtained with the Bhn for different metals and alloys. In Fig. 1 a vertical load L is applied to a compara- tively hard ball of diameter D creating an indentation of diameter 6 and depth h on the specimen S. The work done, W, is then given by W = So Ldh. [I] Since L is not independent of h, Honda and Takahasip and Matsumura" assumed different functions leading to equations which do not apply equallye to a wide variety of metals and alloys. A better relation is obtained from Meyer's Law L = ad" [2] where A and n are constants depending on the nature of the material but independent of the ball diameter D. From Fig. 1 it is obvious that h = R(l — cosq) and d = 2R sin 8.

Jan 1, 1957

Jan 1, 1902

By Walter F. Gries

AN ounce of prevention is worth A a pound of cure' is an old proverb that has sometimes been forgotten in programs having to do with the health of workmen. Realization of the truth of this maxim is increasing, however, and today the iron-mining industry, with which I am particularly concerned, is becoming more alive to the prevention of illness and the conservation of health, thus decreasing the need for treatment after diagnosis has established its necessity. The healthy workman is the happy, efficient workman, and new programs tending to make him more health-minded are being put into operation. Preventive medicine is less costly than corrective medicine, to say nothing of the better results obtained. Periodic physical examinations, with close follow-up attention when required, have reduced the time lost because of illness, workmen's compensation costs, and group-insurance benefits for nonindustrial disabilities.

Jan 1, 1939

By Mark Malamphy

DURING colonial times, Brazil was famous for the richness of her alluvial gold deposits. Paul Ferrand has estimated that the gold produced during the period from 1700 to 1820 was the equivalent of some 64 million pounds sterling. Since that time, most of the more prolific alluvial deposits have been exhausted. A few gold mines are still func-tioning, notably the Morro Velho mine, which is one of the deepest mines in the world. Today, the gold production of Brazil is insignificant when compared with world figures, but there are still many gold-bearing regions and it is probable that in at least some of them profitable returns would result from an exploitation program taking advantage of all the most modern innovations in gold mining and ore treatment on a large scale. In order to demonstrate the value of some of these abandoned pros-pects and stir up interest in increasing the national gold production, the government has stimulated research. Experimental plants have been and are being established in various places, and tests on large quantities of ores are being carried out on a semicommercial basis. The Geological Survey of the State of Minas Geraes is very active in this line and the Federal Institution is also showing an increased interest in the matter. One of the lesser known gold-bearing regions of Brazil is in the vicinity of Lavras, in the State of Rio Grande do Sul. Gold was first reported from this region in the early part of the nineteenth century. In 1811, D. João VI sent an experienced prospector from Minas Geraes to investi-gate the validity of the reports. According to the reports of Baron

Jan 1, 1934

By P. LaRochelle, K. Y. Lo, A. L. Tamuly Phukan

In many civil or mining engineering works, the stresses and deformations of natural or excavated slopes due to the combined effect of self-weight and initial stresses are of interest. Because of the mathematical complexities of this problem, however, no complete exact solution exists for the simplest case, that of assuming the stress-strain relation of the rock to be perfectly elastic. Efforts have therefore been directed toward numerical and experimental technique. The stresses within an elastic slope have been obtained by LaRochelle,1 using the photoelastic and finite difference method to determine the difference and sum of principal stresses. Subsequently, Finn,2 Hoyaux and Ladanyi,3 and Duncan and Dunlop4 attempted to solve the same problem by using the finite element method. The problem was also investigated by Brown and Goodman5 and Brown and King6 who emphasize the importance of the effect of loading or unloading procedure on the stress distribution within the slope. Although the geometry of the slope and the boundary conditions involved are identical or similar, the results obtained by these various authors by no means agree. It is therefore necessary to review briefly the results of elastic analysis in order to lend credence to the methods used in the solution. Although the stress-strain behavior of some rocks may be reasonably approximated by the elastic modrl, other rocks generally exhibit an elasto-plastic behavior with strain hardening or strain softening as shown in Fig. 1. Experiments show that for most rocks, the stress-strain relationship is approximately linear from the origin to the point P (neglecting the small concave region under low stresses). At P, the curve deviates

Jan 1, 1970

By C.A. Zapfee, C. E. Sims

An investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. Apparatus The apparatus is shown in Fig. r and the system is shown by diagram in Fig. 2. Furnace, A lmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In this furnace fres oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1943

By C. A. Zapfee, C. E. Sims

An investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. Apparatus The apparatus is shown in Fig. r and the system is shown by diagram in Fig. 2. Furnace, A lmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In this furnace fres oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1943

By J. E. Dreier

The Pachuca - Real del Monte district has produced about 46.6 kt (51,300 ton) Ag from subvolcanic vein deposits. Three types of wall rock alteration are spatially related to the veins: K-feldspar, propylitic, and phyllic. K-feldspar alteration occurs within veins; propylitic alteration occurs in fractured rocks between veins; and phyllic alteration occurs above veins. Concentrations of some trace elements in altered rocks relative to unaltered rocks are summarized below. [ ]

Jan 1, 1983

By Thos Gibson

THE object of taxation is the raising of a revenue. Unless a tax accomplishes this, it is a failure. The right to take for public purposes a part of the moneys obtained from the carrying on of private enterprises is an attribute possessed only by a lawful government, and may indeed he called the supreme attribute of government. In free, democratic communities this power must of necessity rest upon the consent of the governed. Power implies obligation, hence it is obviously the duty of a government, in framing a system of taxation, to provide one which, while effective in producing a revenue, is also just and impartial. It will be conceded that mines and mining property ought to bear a fair share of the public expenditure. The question is, upon what basis taxation should proceed. Two separate taxing principles are usually contended for: Taxation should be proportionate to the benefits received by the person or property taxed; taxation should be based on ability to pay. A third is sometimes added, taxation should have reference to the extent and value of the natural resources enjoyed. As applied to mining taxation, it is pointed out by those who support the first mentioned basis that, mines being usually situated in rocky and hence sparsely peopled regions, mining companies are frequently obliged to construct roads, railways, telegraph and telephone lines, schools, water and sewerage systems, and many other amenities and conveniences of civilization, the cost of which in regions better suited for agriculture and consequently more thickly populated, has either been defrayed locally, or can be spread over a sufficiently large taxable group of people to materially lighten the financial burden on the mine. The mining com¬pany, it is argued, having made these outlays, should receive credit for, them and be relieved of taxation to a corresponding extent. There may be some force in this contention, but the situation is capable of relief without attempting to place taxation upon so unworkable a basis as the value of benefits received. Who is to be the judge of these benefits, and how are they to be valued? The very existence of a mining company and its ability to carry on business in peace and security, depend on the prevalence of law and order, which is a result of good government. The state provides protection against violence, and courts of law for

Jan 4, 1919

By S. J. Green, R. D. Perkins

Little data exists on the high strain rate behavior of geologic materials. Uniaxial stress tests by Kumar1 and by Serdengecti and Boozer2 present some results to strain rates in the range 10 to 103 per sec. The two references cited are the only ones the authors found for high strain rates. Techniques for experiments at high strain rates are not well developed and, in general, leave questions with respect to interpretation of data when the material behaves in a brittle manner. The most reliable data at very high strain rates (104 to 106 per sec) are found in some recent flat-plate work3-5 where experimenters have impacted one plate into another, thereby creating a uniaxial strain loading. The standard uniaxial stress-strain curves cannot be obtained directly from these tests; however, yield (or fracture) may be studied by measuring the "elastic" wave magnitude. These data then may be compared to uniaxial stress data by resorting to some preassumed yield/fracture criteria. Even with the most liberal interpretation of existing data, little can be said of the effects of high strain rate on stiffness, yield/fracture, and post-fracture behavior of geologic materials. It is the purpose of this work to begin to add to the understanding. The data presented here are intended to provide material information for use in calculating the response of geologic materials to high rate deformations. These data can be applied directly to determine parameters such as the elastic modulus and Poisson ratio as a function of stress. Furthermore, these data can be used to derive an understanding of yield/fracture and the effect of rate on the yield/fracture surface. The work presented is a first step, and is

Jan 1, 1972

By R. A. Falconer, H. L. Lovell

With increasing requirements for fine coal cleaning and the many advantages of the cyclone operating on a coal-water slurry, a series of studies designed to achieve an enhanced understanding of the cyclone parameters has been pursued. The purpose of this investigation has been to vary a series of dimensional parameters with an experimental 15-in. diam hydro-cyclone, and to determine the relative effects of parameter variations upon ash and sulfur removal. This study of the hydrocyclone is a continuation of a series of investigations, conducted in the Dept. of Mineral preparation at The Pennsylvania State University, which are directed toward the removal of ash and sulfur constituents from fine bituminous coal by size-density separations in cyclones, and toward a fuller understanding of the complex mechanisms involved in such separations. The purpose of this investigation has been to vary a series of dimensional parameters with an experimental 15-in. diam hydrocyclone, and to determine the relative effects of parameter variations upon ash and sulfur removal. Of special interest was the response to cone angle variation, since it is the high included cone angle that generally distinguishes the hydrocyclone as a gravity separator rather than a classifier. DESCRIPTION OF THE HYDROCYCLONE Fig. 1 is a dimensional drawing of the hydrocyclone used in the investigation. The unit was designed and fabricated by Heyl and Patterson, Inc., for experimental use. The dimensional parameters considered were: 1) Three cone sections having included angles of 45, 60, and 95,degrees, 2) Three 3 1/8 in. diam vortex finders having lengths of 15, 17, and 19 1/2 in., 3) Three 4 1/16 in. diam vortex finders having lengths of 15, 17, and 19 1/2 in. 4) Two apex sections having diameters of 2 and 2 1/4 in. The feed inlet orifice had a fixed diameter of 3 in. The hydrocyclone test installation was made at The Pennsylvania State University pilot plant at Barnes-boro, Pa., which operated at 50 tph. During the period that the hydrocyclone was tested, research was in progress at the Barnesboro site to reprocess refuse material from a near-by coal preparation plant in

Jan 1, 1968

By Lloyd R. Jackson

IN the past 15 years there has been a great deal of interest in the fundamentals of plastic flow and rupture in metals and a number of papers have presented substantial advances toward a fundamental insight into the mechanism of these two processes. This paper is an appraisal of the present position with respect to the following: I. The relative importance of shear and hydrostatic stresses in controlling the plastic flow of metals. 2. The relative importance of shear and hydrostatic stresses in determining the amount of flow before rupture in metals. 3. The use of generalid strains in determining the effect of plastic flow on the work-hardening of metals. FUNDAMENTALS INVOLVED IN PLASTIC FLOW In attempting to devise a quantitative description of plastic flow in metals, it has been customary to assume that metals are homogeneous and isotropic. The fact that neither of these assumptions is correct complicates the experimental appraisal of relations developed. Never- the less, as will be shown, metals are close enough to being isotropic and homogeneous so that considerable insight into the mechanism of plastic flow can be obtained. The assumptions of .isotropy and homogeneity allow both the elastic and plastic behavior of metals to be described in terms of 12 variables-six being stress variables, and six being strain variables. ) From this viewpoint, it should be possible to represent the stress-strain relations in the plastic range for metals by a surface in 12 dimensions. One boundary of this surface would be the surface of transition from elastic to plastic behavior; the other would be the surface of rupture. These two surfaces would be joined by the surface of plastic flow. The shape of this composite surface would depend on the test temperature and speed of straining. This paper is concerned only with results obtained at constant temperature and constant speed of straining. While such a representation is conceivable, the demonstration of such a surface would present almost insurmountable obstacles. The most fruitful simplification of this concept has been the recognition that the behavior of metals in the plastic region is primarily a result of shear stresses and strains. Based on this viewpoint, it is possible to utilize stress and strain invariants that are independent of hydrostatic components to define an effective stress and strain. In effect, this amounts to reducing the task of representing stresses and strains in 12 dimensions to one of representation in two dimensions. The two invariants (one for stresses . and one for strains) that have received most attention are the following: [ ]

Jan 1, 1946

The Report on the Manufacture of Coke for the year 1880 by J. D. Weeks1 includes an historical account of the early days of coke-making that is very complete and accurate, and but little can be added to it to fully cover the period prior to 1885. The few additional references that have been found follow. The earliest suggestion found about making coke in this country is in a letter from D. M. Randolph to Harry Heth, dated August 22, 1808. Heth was then operating the mines in the Richmond, Virginia coal field and had sent Randolph to England to investigate steam engines for hoisting and pumping and other conditions in the coal industry there. The letter was written in London and said: "I shall explain to you, how, by turning Deep Run fine coal in Coak, to make great profit from what has heretofore been useless. You will do well to ascertain the price and amount of demand for this article throughout the U. States among brewers and manufacturers. I know how also to make every bushel of such fine slaty coal, fetch as much as any of the best grate coal, by turning it into Coak: and that too, after paying all expenses of the process."2 His interest was to use the slack more for domestic purposes than otherwise, probably, although what the interest of brewers would be in coke as fuel does not appear. Nothing ever came of this suggestion, and so far as known, no coal from this field was coked excepting in gas-making. The Plumpsock Iron Works, mentioned by Weeks as having used coke, was advertised for sale in June 1818.3 It was stated that stone coal was the only fuel used at the works, the pit being within 100 yards of the forge. "Three men with a horse and cart are sufficient to raise coke, and haul to the forge all the coal necessary for keeping the works in full operation." The coke, of course, was made in ricks, or heaps, and not in ovens. The first real coke oven in this country was probably built in Connellsville, the coal coming from a mine nearby on Mounts Creek. L. L. Norton operated an iron foundry and was persuaded by his foreman, one Nichols, who came from Durham, England to build a coke oven. The oven was 12 feet square, and the first coke was produced in 1833. Later

Jan 1, 1942

By Frederick Jr. Prime

THE first catalogue of Geological Reports of the United States was prepared by Prof. O. C. Marsh, and published in the American Journal of Science and Arts for 1867, vol. xliii, second series. Since then the list has more than doubled, and it was thought that the publication of a new catalogue, brought down to date, would be useful to many of the members of the Institute of Mining Engineers. The compiler will be most thankful to have any omissions or inaccuracies in the list sent to him, to be published as a supplement in the next volume of the Transactions. Especially to have the correct title, number of pages, plates, and maps of any volume on the list to which an * is prefixed, as he has been unable to personally consult such works. A preliminary list was issued last February, which has been almost doubled by the kindness of many friends. The writer desires more especially to express the obligations he is under to the following gentlemen The Chief of Engineers, U. S. A.; Principal Dawson, Mr. G. M. Dawson, Drs. B. J. Harrington and T. Sterry Hunt, of Montreal; Mr. H. Engelmann, of La Salle, Ill.; Dr. F. V. Hayden and Prof. J. W. Powell, U. S. Department of the Interior ; Prof. E. W. Hilgard, University of California; Prof. Henry Y. Hind, Windsor, N. S.; Prof. C. H. Hitchcock, of Dartmouth College; Mr. Henry A. Holmes, State Librarian, Albany; Maj. Jed. Hotchkiss, Staunton, Va. ; Prof. W. C. Kerr, Raleigh, N. C.; Dr. J. S. Newberry, of Columbia College ; Prof. W. H. Pettee, of the University of Michigan ; Dr. Samuel H. Scudder, Prof. N. S. Shaler, and Prof. J. D. Whitney, of Harvard College ; Mr. Sanderson Smith and Prof. J. J. Stevenson, of New York ; Mr. Addison Van Name, of Yale College, and Lieut. Geo. M. Wheeler, U. S. Engineers. PHILADELPHIA, 907 Walnut Street, October 1st, 1879.

Jan 1, 1879

By F. M. Lyon, F. J. Chernosky

Research efforts have not developed techniques for the complete desulfurization of coal that is needed to reduce air pollution caused by burning coal and to reduce the sulfur in metallurgical coke. Sulfur in coal occurs in three forms and of these, the pyritic sulfur occurs as discrete mineral particles and, at least theoretically, should be subject to physical rejection. Pyrite occurring in hard rock mining is concentrated by froth flotation; therefore, the possibility of removal of pyrite from coal by flotation does exist. With this possibility in mind, the flotation and adsorption characteristics of ore and coal-pyrite were compared while using potassium ethyl xanthate as the collector.

Jan 1, 1973

By C. E. Sims, C. A. Zapffe

AN investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. APPARATUS The apparatus is shown in Fig. I and the system is shown by diagram in Fig. 2. Furnace Atmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In [ ] this furnace free oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1942

By R. R. Byran, M. H. Kuryla

The Compania de Real del Monte y Pachuca started a 10-ton pilot plant in March, 1906. The distinctive features of the first cyanide installations at Pachuca were: grinding in cyanide solution, all-sliming and filtration of ore in which silver constituted the major value. Loreto started with a 300-ton " all-sliming" plant, using jaw crushers, grinding in stamps, Chilean mills and pebble mills in cyanide solution, concentrating with Wilfley tables and Johnson vanners, classification by cones and Dorr classifiers, intermittent thickening by decantation, mechanical agitation in flat tanks by stirrers and centrifugal pumps, filtration in Butters filters and precipitation by zinc shavings. The "San Francisco" mill No, 1 was contemporaneous, using a rather similar flow sheet. We shall trace the main developlnents in the three large mills of the district to their present practice. Developments in Large Mills of District Crushing and Grinding.—The trend of development in this part of the work has been the same as throughout the milling world; via., all increase in the degree of comminution of the ore in dry-crushing machines, the advance from pebble mill to rock mill and then to ball mill and the elimination of the stamp battery through the encroachment upon its field on the one side by finer dry crushing and on the other by more efficient wet grinding. The single-stage crushing in jaw type crushers, used at the start, has been replaced by two stages; at first, both stages by gyratory type and later the present practice, which is the same in all three mills, consisting of gyratory as primary followed by cone as secondary and delivering a product that may be rated at 56 to 1 inch. Primary wet grinding, at first performed by stamps and Chilean mills, is now by hall and/or rod mills; present practice differing widely in the three mills. Santa Gertrudis uses a 7 by 15 ft. rod mill, San Rafael

Jan 1, 1935

By C. E. Sims, C. A. Zapffe

AN investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. APPARATUS The apparatus is shown in Fig. I and the system is shown by diagram in Fig. 2. Furnace Atmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermo-couple and potentiometer (9) and is controlled by a slidewire resistance (10). In [ ] this furnace free oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1942