Search Documents

By Mark J. Klein

The creep of 043 was studied over the temperature range 1650" to 3200°F and over the stress range 3000 to 44,000 psi. The steady-state creep rate over this range of stress and temperature can be expressed by the equation where A is a constant, is the stress, and is -0.8 x 103 psi-'. Over a narrow range of stress variations c0 a and for this proportionality n varies from 3 to 30 in accordance with the relation n = aB. Above about 2400° F, H, the apparent activation energy for creep, is 110,000 cal per mole, a value about equal to that estimated for self-diffusion in this alloy. Below 2400°F, H increases with decreasing temperature reaching a value of -125,000 cal per mole at 1700° F. In this temperature region, H appears to be a function of the interstitial concentration of the alloy. MOST of the detailed creep studies of dispersion strengthened metals have been concerned with metals having fcc structures. However, there are a number of important refractory alloys with bcc structures that derive part of their high temperature strength from an interstitial phase and whose creep behavior has not been well defined. This paper describes the creep behavior of the bcc alloy, D43, over the temperature range 1650" to 3200°F (0.4 to 0.7 Thm) and over the stress range 3000 to 44,000 psi. In addition to colum-bium, this alloy contains 10 pct W. 1 pct Zr, and sufficient carbon (-0.1 pct) to form a carbide dispersion throughout the matrix of the alloy. The effects of variations in temperature and stress on the steady-state creep rate of this alloy are presented in this paper. EXPERIMENTAL PROCEDURES Creep tests were made in a vacuum of 106 torr under constant tensile stress conditions using a Full-man-type lever arm.' Creep specimens were machined from 0.020-in. D43 sheet (grain size -5 x l0-4 in.) processed in a duplex condition (solution annealed -2900°F, 40 pct reduction in area, aged 2600°F). The specimens were tested in this condition without further heat treatment. Specimen extensions over 1-in. gage lengths were continuously recorded using a high temperature strain gage extensometer. Differential temperature and stress measurements were used to determine temperature and stress dependencies of the creep rate. Activation energies were calculated from the changes in strain rate induced by abrupt shifts in the temperature during constant stress creep tests. The 100°F temperature shifts used in most of the activation energy determinations required 15 to 90 sec depending upon the temperature at which the shift was made. The dependence of strain rate on stress was determined by measuring the change in strain rate for incremental stress reductions during constant temperature tests. It has been shown that columbium-base alloys such as D43 are susceptible to contamination by gaseous interstitial elements during vacuum heat treatments.' In this regard, it is unlikely that these alloys can be heat treated without some loss or gain of interstitial elements despite the precautions taken to control the heat treating environment. However, several factors suggest that changes in interstitial concentrations of the specimens during testing did not affect the results presented in this paper. First, the dependence of the creep rate on the stress or temperature determined during the course of a single creep test showed no variations with the duration of the test. A variation would be expected if a loss or gain in interstitial concentration during the course of the test affected results. In addition, precautions taken during this investigation to minimize interstitial contamination by wrapping the gage lengths of the specimens with various foils2 (Mo, Ta, W) did not produce a detectable change in the stress and temperature dependencies relative to the unwrapped specimens. The averages of duplicate analyses for carbon and oxygen in several specimens determined before and after creep testing are listed in Table I. The combined nitrogen and hydrogen concentrations which were ordinarily less than 50 ppm did not change in a detectable way with creep testing. The analyses show that only minor changes in carbon concentration occurred during creep testing except for specimen 4. This specimen which was tested at 3100°F lost a significant amount of its carbon concentration to the vacuum environment. Specimen 1 gained 100 ppm of O, while specimens 2, 3, and 4, which were tested at progressively higher temperatures, lost increasing portions of their initial oxygen concentrations during testing. RESULTS AND DISCUSSION The Temperature Dependence of the Creep Rate. The apparent activation energy for creep, H, was de-rived from creep curves similar to that shown in Fig. 1. Steady-state creep was rapidly attained at the beginning of the test and with each change in temperature. This behavior suggests that the alloy rapidly attains a stable structure with each shift in temperature or that the structure is constant throughout the test. Since the dispersion will tend to stabilize the structure, the latter is probably the case. The activation energy was found to be independent of the direction of the temperature shift and the magnitude of the shift (50" or 100°F). Although H was approximately independent of the strain, there was a tendency for it

Jan 1, 1970

By Wayne L. Worrell

Thermodynamic data for the stable carbides and oxides of chromium, molybdenum, and tungsten have been critically eualuuted and are used to determine the stable condensed phases at 1 atm total pressure in each metal-carbon-oxygen system. Pourbaix-Ellingham diagrams have been constructed and are used to estimate the minimum temperatures neces.see)*y to oblain these metals by corbolhermic redlrction under reduced pressures. USING recently reported data for the carbides and oxides of chromium, molybdenum, and tungsten, the stable phases in the Group VI metal-carbon-oxygen systems at specific temperatures and pressures can be determined. The thermodynamically stable regions in each metal-carbon-oxygen system can be completely pictured using a Pourbaix-Ellingham diagram in which the two coordinates are oxygen potential (-RT In Po2) and temperature. Worrell and chipman' have described and constructed such diagrams for the metal-carbon-oxygen systems of vanadium, columbium, and tantalum. Downing2 has used similar diagrams to provide a description of the reactions in submerged arc furnaces. One of the examples which he cited was the Cr-C-O system; however, an improved diagram is presented in this paper using recently obtained data for the carbides of chromium. Although some of the oxides and carbides of the Group VI metals exist over slight ranges of composition,3 all solid phases are represented as stoi-chiometric compounds in the subsequent diagrams. Any error introduced into the calculated equilibria by neglecting the compositional variation of these phases is less than the uncertainty in the thermodynamic data. In a Pourbaix-Ellingham diagram for a three-component system, the phase rule requires that at equilibrium four condensed phases specify a point, three condensed phases determine a line, and two condensed phases define an area. To obtain a well-defined area at high oxygen potentials and teniperatures, the initial carbon to oxygen mole ratio is specified to be more than sufficient to reduce the oxide but not enough to convert all the metal to carbide. Thus, the lowest regions in the subse- quent Pourbaix-Ellingham diagrams represent areas in which the metal and its carbide are the stable condensed phases. Cr-C-O SYSTEM A) Thermodynamic Data. To simplify the subsequent calculations, all thermodynamic data are presented in the form of linear Gibbs-energy-of-formation* equations which were derived for the temperature range 505° to 2000°K and are reasonably accurate over the entire temperature ranges of the diagrams. The thermodynamic data for the compounds occurring in the Cr-C-O system are summarized in Table I. Several volatile chromium oxides have been reported,4 but their influence is negligible in the Cr-C-O system. Thermodynamic data for CO and CO2 were taken from the compilation of Coughlin.5 The only solid chromium oxide sufficiently stable to exist below 1800°K in the Cr-C-O system is Cr2Os.11 The Gibbs-energy-of-formation equation for Cr2O3 was obtained by revising the data tabulated in Coughlin,5 using the heat of formation of ah' and the high-temperature thermal data for chromium.7 In 1953 Richardson8 re-evaluated the original work of Kelley and coworkers,9 who measured the thermodynamic properties of the chromium carbides. However, the high-temperature equilibrium results of Boericke9 yield values for ?G°f of Cr2O3 which are 2 kcal more positive than the accepted data. His results for the chromium carbides are based on the same questionable equilibria. Gleiser10 recently determined the Gibbs energy of formation of Cr3C2 and the equation in Table I was calculated from her data and the thermal data of Kelley and coworkers.9 Thermodynamic data for the Cr7C3 and Cr23C6 carbides were obtained by combining the Cr3C2 data

Jan 1, 1965

By P. Chiotti, J. T. Mason

Thermal, X-ray, metallographic, and resistivity data were obtained to establish the phase diagram for the Yb-Zn system. Six intermetallic compounds and five eutectics have been identified. The compounds position at 695°C. No evidence for the compound YbZn,, was observed. Whether this compound is stabilized or inhibited by small amounts of impurities is uncertain. SEVERAL aspects of the Yb-Zn system have been reported in the literature. Much of this work deals with the crystallographic identification of some of the compounds. The YbZn compound has been reported by Iandelli and palenzonal and the YbZn, structure and thermal data for the composition range between YbZn and Yb3Znll have been reported by Michel et al. A compound of uncertain stoichiometry in the range 60 to 68 wt pct Zn with a cubic structure has been reported by Kuz'ma et aL4 The YbzZn17, YbZn,,, and YbZn13 compounds have been reported by both Kuz'ma et a1 and Iandelli and Palenzona.' YbnZn17 has also been identified by Laube. This investigation was undertaken to establish the phase diagram of this system. Ytterbium in many respects behaves as an alkaline earth rather than a rare earth metal6 and it is of interest to note the resemblance between the Yb-Zn system, the Ca-Zn,' and typical rare earth-zinc systems.g'10 MATERIALS AND EXPERIMENTAL PROCEDURES The materials used in this investigation were Ames Laboratory ytterbium and Bunker-Hill slab zinc, 99.99 pct pure. Analyses of the ytterbium showed 38 ppm Ta, 82 ppm 0, and 15 ppm N with Ca, Cu, C, Mg, Al, Si, Cr, Fe, Ni, Sc, Y, Er, Tm, and Lu all less than 50 ppm. The ytterbium was dehydrogenated by heating in tantalum under vacuum for 8 hr at 900°C. The metal was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys in the composition range between ytterbium and Yb2Zn17. With higher zinc concentrations the tantalum was penetrated by the alloy and failed after several days at temperatures of 600" to 700°C. Approximately 20 g of zinc and ytterbium metal were sealed under argon in *-in.-diam tantalum cruci- bles equipped with thermocouple wells. The crucibles were in turn sealed in stainless-steel jackets. The alloys were equilibrated in an oscillating furnace and given various heat treatments in a soaking furnace. The steel jackets were removed and differential thermal analysis data were obtained under an atmosphere of argon. The thermal analysis apparatus was calibrated against the melting points of pure zinc, aluminum, silver, and copper and found to give thermal arrests within 1°C of the accepted melting temperatures for these elements. The thermal analysis apparatus has been described in an earlier paper.g Alloys were further heat-treated as necessary and subjected to metallographic examination and X-ray diffraction analysis. Most alloys were etched with Nital (0.5 to 10 pct nitric acid in alcohol). EXPERIMENTAL RESULTS The results of the thermal analysis are summarized by the points on the phase diagram, Fig. 1. Six compounds and five eutectics were observed. The eutectic temperature and compositions in weight percent zinc are 491°C and 12 pct, 645°C and 32 pct, 687°C and 54 pct, 742°C and 67 pct, and 750°C and 77 pct. The compounds YbZn, YbZn2, Yb2Zng, Yb2Zn17, and YbZnll melt congruently at 650°, 751°, 75Z°, 754", and 755"C, respectively. The compound Yb3Znll undergoes a peritectic decomposition at 695°C. The transformation and melting temperatures for the ytterbium were observed to be 797" and 817°C. re-

Jan 1, 1969

By S. F. Shaw

The principles involved in lifting oil in wells flowing naturally are identical with those underlying the flowing of wells by means of the air-gas lift, and information of a dependable nature obtained in the study of the air-lift can be applied to wells with natural flow. A well flowing naturally is one in which the lifting is done by means of the gas-lift, for which the gas is supplied entirely by the formation from which the oil is derived. In air-gas lift operations, there is insufficient gas supplied by the formation to lift the oil to the surface in an efficient manner, therefore additional gas for this purpose must be furnished from an outside source. There may, at times, be conditions obtaining in natural flowing wells different from those in wells flowed by gas-lift, but these differences do not at all conflict with the main principles of gas-lift work. One such condition is met with in wells in which the gas supplied by the formation is in considerable excess of that required to lift the oil to surface; this excess may be so great as to reduce the quantity of oil that can be lifted through the particular diameter of casing or tubing that has been lowered into the well. This same condition can be brought about, however, by supplying a large excess of gas from an outside source to an artificial gas-lift well, and a study of the effects obtained from injecting a large excess into the well can be applied directly to handling wells flowing naturally which have a large excess of gas supplied by the underground reservoir. Conditions for Lifting Oil The main factors to be considered in flowing wells are as follows: 1. Submergence, or pressure at the bottom of the tubing or casing. 2. Lift; the height to which the liquid must be raised. 3. Diameter of the flow tubing or casing. 4. Quantity of liquid to be lifted. 5. Pressure at the discharge end of the flow tubing, or back-pressure, as it is sometimes called.

Jan 1, 1930

LIST OF MEMBERS AND ASSOCIATES ARRANGED ACCORDING TO STATES AND TOWNS ALABAMA Aldrich, Aldrich, W F Anniston, Noble, A E, Smith, N B Aibacoche, Bradley, D II Bessemer, Fergusson, V Birmingham, Aldrich, T H, Aldrich, T H, Jr, Bowron, J, Bowron, C E, Davis, F H, Dimmick, F D, Hillman, McCarthy, M E , McCormack, McCrery, Ramsay, E, Shook, A M Bridge¬port, Wheeler, S K Ensley, McDonald, S, Shook, J W Fanbanks, Hamil¬ton, A L Helena, Squire, J Huntsville, Moss Lehigh, Toulmin Oxmoor, Green¬amyer, A G Plasma, Gage Rock Run, Garvin Sheffileld, Miller, D I Tuscaloesa, Lodge, J University, McCalley Woodward, Bukofzer, Woodward, A H ALASKA Dawson, Buck Douglas Island, Corbus, J P , Macdonald, J Hames, Le Wald, E A Jualin, Hoggatt, W B Juneau, Denby, Gaifield, Garside, Hamp¬ton, W H Rodman Bay, Phillpots Snettisham, Tisdale Sumdum, Thane Tel¬ler, Hirshberg, M R Treadwell City, Batcheller, J H , Kinzie Valdez, Esterly, G M Yukon, Dawson, Elmer, J M ARIZONA Bisbee, Clark, G C, Coombs, H L , Douglas, W, Hoatson, Parnall, S A, Pelton, R T, Ricketts, L D, Sherman, G F G, Smith, F W, Smith, H A Black Diamond, Bagge Blanchard, Cummins, Murray, J J Casa Grande, Rich¬mond, A B Clifton, Colquhoun, Grabill, Murray, H T , Plater, Smith, J D A, Veitch, Watson, W S Congress, Goodloe Crown King, Alexander, G E Douglas, Cornell, Kraemer, E L, Lee, G B, Rutherford, F Globe, Berray, Hoar, Snell Harrisburg, Smith, F C Jerome, Clark, W A, Thomas, C A Kingman, Treadwell, Wallace, J P Kirkland, Bretherton, G K Kofa, Lamp¬shire, J O , Pomeroy, H G Mayer, Haggott, E A Metca j, Blumenkranz, M , Forbes, D L H Morenca, Clark, C D, Fleming, J B, Honey man, Mills, C E, Wallace, L R Morristown, Stevens, H W Nogales, Glove, H G, Sandoval, A , Sandoval, P Octave, Rose, G W Phoenix, Armstrong, T , Butler, C E, Defty, Lindsay, L Prescott, Blauvelt, H , Bunker, C E, Claypool, W M , Drescher, F M , Fairbank, Nissen Tombstone, Gage, Poindexter, C L , Staunton, Walker, E W Troy, Cutting Tucson, Blake, W P, Burgess, De Lashmutt, I, McCleary, Mann, Prout, J W , Jr ARKANSAS Fayetteville, Purdue Fort Smith, Bache, F , Denman, H Little Rock, Fordyce, Scholz CALIFORNIA Alameda, Arents, King, L Arnador City, Downs, Tregloan Angeles Camp, Dig¬gles, R N , Kenney, C E Antioch, Belshaw Auburn, Coe, I J Ballarat, Thorns Berkeley, Abadie,, Christy, Dozier, Hall, F F , Hersam, Landfield, Lind¬say, L , Mansfield, N T, Morley, W S , Sharwood, W J Bag Oak Flat, Dron Bodae, Hamilton, W R, Hoover, T, Hoover, T J, Jackson, B L , Nutter , E, H Bullion, Power, H T Callahan, Scott, E H Campo Seco, Baird Cartero,

Jan 1, 1910

By M. T. Hepworth, R. Schuhmann

Hydrogen solubility measurements were made on a series of Ti-O alloys, and a portion of the 800°C isotherm for the Ti-O-H system was determined. Activities of oxygen and titanium were calculated from the experimentally measured activities of hydrogen, using ternary Gibbs-Duhem integrations. The data were extrapolated to obtain thermo-dynamic properties of binary Ti-O solutions. The thermodynamic properties of a Ti-0 solid solutions thus determined were compared with properties predicted from interstitial models. The Gibbs-Duhem equation, long used to calculate activities in binary systems, has been extended. recently to ternary systems.1"3 When the activity of one component in a ternary system is known as a function of composition, the activities of the other two components can be calculated from that of the first by an integration procedure, provided certain restrictions are observed on the path of integration. Often the activity of one component in a ternary system can be measured readily, while the activities of the other two components are difficult to measure. Gibbs-Duhem calculations are especially applicable to such systems. The further possibility arises of developing a new and indirect approach to activity measurement in binary systems. The proposed new method for binary systems consists of adding varying amounts of a third component whose thermodynamic behavior is easily measured. The activity of this added component is determined experimentally as a function of composition. Then the activities of the two components of the original binary system are calculated by Gibbs-Duhem integrations and extrapolations. For the work to be described in this paper, the Ti-0-H system was selected as a promising system for evaluating this approach. Investigations of the Ti-H system have shown that the activity of hydrogen can be measured precisely with little difficulty. Pure titanium transforms from a low-temperature a form (hcp) to a higher-temperature /3 firm (bcc) at 882.5"~ The phase transformation occurs in a temperature range where hydrogen pressures are easily measured. Also, the diffusivity of hydrogen at temperatures above 600" or 700"~ is large enough that equilibrium can be reached within a reasonable time.

Jan 1, 1962

By F. G. Tahmoush, N. J. Grant, E. P. Abrahamson

The effect of grain size on the brittle -ductile transition temperature of pure iron and three dilute Fe-W alloys has been investigated by slow bend tests. The brittle-ductile transition temperature for pure iron increased with increasing grain sizes from 8000 to 500 grains per sq mm where the transition temperature then decreased with further increase in grain size. The dilute additions of tungsten lowered the transition temperature for fine grain sizes, suppressed a reversal of the curve in the coarse grained portion, and raised the transition temperature for this region. The frequency of twin occurrence increased with increasing grain size and decreasing temperature. The object of the present investigation was to re-examine the effect of grain size on the brittle -ductile transition of pure iron and several dilute Fe-W alloys. Current literature normally presents a simple relationship between grain size and the brittle-ductile transition temperature, namely, that the transition temperature increases with increasing grain size. Heslop and etch' have studied the transition temperature of mild steel by V-notch Charpy impact tests for the grain size range between 200 and 6000 grains per sq mm. The result was a linear plot of In 1-1/2 vs brittle-ductile transition temperature, where 1 is the grain diameter. Recent experiments by sipos2 revealed the possibility of a reversal in the slope of the grain size vs transition temperature plot for pure iron; however, his investigation was limited in scope, and the data obtained were insufficient to permit a definitive curve. The present investigation was undertaken in an effort to confirm or extend the grain size effect observed in iron by Sipos. PROCEDURE All alloys were vacuum induction melted, using 99.95 pct Fe containing 0.03 pct 0 and 0.004 pct C. Four ingots were made, ranging from pure iron to iron with 0.035 pct W. The chemical composition of each alloy, after processing, is given in Table I. The four alloys were prepared as 45 lb heats and cast into 4 in. diam by 16 in. molds. They were then extruded into 3/4 in. rods at 1800oF. Specimens for chemical analysis, taken from various positions along the rods, revealed no variation in tungsten content along the length. The extruded rods were reduced to 0.156 in. diam stock by a series of cold swaging operations involving intermediate vacuum annealing treatments. This procedure yielded a final cold reduction in area ranging from 10 to 90 pct. The swaged rods were chemically cleaned, cold pressed to a cross section of 0.10 by 0.18 by 1.0 in. long (2.54 by 4.73 by 25 mm). The specimens were wrapped in iron foil and vacuum sealed (10-4 mm Hg) in quartz. Various heat treatments at temperatures from 700" to 1300oC were utilized to produce grain sizes from 8000 to 1 grain per sq mm. Grain sizes were determined by measuring the average area of grains in a polished section. In specimens with grain size greater than 20 grains per sq mm, the total number of grains in the cross section was counted and then divided by the area to yield grains per sq mm. Grain size was measured both for longitudinal and transverse cross sections. The average of the two measurements was plotted vs transition temperature. An Instron Table Model testing machine was used to determine the transition temperature of specimens tested in three point horizontal bending. The specimen was supported by two 1/4 in. dowels one in. apart. Bending was accomplished with a push rod, the end of which had an 1/8 in. radius. The head speed was 50 in. per min. Temperatures were established through the use

Jan 1, 1963

By P. de Vitry, Oliver Bowles

THE conventional wire saw, introduced in the slate district of Pennsylvania by the Bureau of Mines in 1927, and used thereafter with remarkable success, consists of a three-strand steel cable having a diameter of 3/16 or 1/4 in. The equipment, methods used, and accomplishments have been described in previous reports.1-7 Similar wire saws have been used extensively in Europe, in quarries and in shaping blocks and slabs. During the period 1932-1937, competition in European marble quarries was keen, prices were declining, and orders were not abundant. When orders were received, there was generally an urgent call for speedy delivery. Because of the diversification of demands, it was impossible to maintain in stock marbles of the color, size, and thickness called for, therefore the material generally had to be fabricated after the order was received. The wire saw enabled stone mills to fill such orders promptly. With skillful handling, 7/8-in. slabs could be cut accurately and rapidly with this equipment. It was found, however, that, as the three-strand wire became worn, the cutting speed dropped rapidly and the cut became less accurate. To overcome these difficulties the junior author of this paper, after much experimentation, developed a new type of wire consisting of a single ribbon-shaped strand, twisted as shown in Fig. 1. To ensure straight sawing, the twist of the ribbon is reversed from right to left and vice versa every 25 ft. The reversal of the [ ] twist is shown in Fig. 2. This is not a new feature; it has been used to advantage with the three-strand wire both in Europe and America for several years. However, some difficulties arise in splicing the three-strand reverse-twist wire, and the claim is made that cutting is less accurate as the wire becomes worn. To make an endless belt, the ends of the single-strand wire are brazed together with

Jan 1, 1941

By E. Swartzman, G. C. Behnke

THE free-swelling index, a numerical value for the free-swelling properties of coal, is being used to an increasing extent in specifying coal for burning in various types of equipment. The empirical standard ASTM method for determining this index uses, as a source of heat, a gas burner which requires frequent calibration because gas pressures are not constant, relatively small changes in gas pressure resulting in rather wide variations in the temperature attained in a crucible and thus in the resultant size of the coke button. Furthermore, the quartz crucibles specified for the test are not standard equipment, and relatively small variations in dimension and wall thickness from those specified often result in rather wide variations in the resultant size of the button. A method of analysis to be satisfactory not only for a scientific laboratory but also for use in industrial control laboratories under varying conditions should employ equipment which is rugged, easily calibrated, and readily replaceable by standard materials. Gas is not universally available as is electricity, and it is generally easier to calibrate and control a simple electric furnace or heater than a gas burner, the voltage not usually fluctuating to the degree that gas pressure does. Quartz crucibles are fragile, and the size specified in the test is not normally used for any other purpose in the laboratory. Although more expensive, the 15-cc platinum crucible, available in all laboratories where volatile matter in coal is determined by the standard ASTM method, is sturdy and standard and easily replaced. Because of these considerations, a modification of the standard method has been developed which employs a standard laboratory 350-w cone heater and standard 15-cc platinum crucibles. The results of numerous tests conducted with such apparatus show conclusively that the free-swelling index values as judged by the buttons produced with this equipment are exactly the same as those obtained by the standard gas burner method. Thus it is suggested that this electric cone heater method employing standard 15-cc platinum crucibles be considered as an alternative to the ASTM method, Designation: D720-46. The free-swelling index of coal is determined by means of the ASTM method, D720-46. This method, which is an adaptation of the crucible swelling test for coal of the British Standards Institution, consists of heating 1 g of coal in a special covered quartz crucible in a regulated gas flame for a period of not less than 2.5 min in which time the temperature of the inner surface of the bottom of the crucible reaches a temperature of 82025°C. The residual coke button is then compared in size and shape with a series of standard profiles shown in Fig. 1 and designated by number from 1 to 9 in increasing order of size. As the method is empirical, it requires rigid standardization of the apparatus and repeated calibration of the gas burner. The dimensions of the low form quartz crucible recommended must be rigidly adhered to as small variations in diameter or wall thickness result in variations in the rate of heat transmission and thus in the resultant size and shape of the coke button. The gas burner must be calibrated almost every time a new set of determina-

Jan 1, 1952

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By M. W. BERNEWITZ

ALTHOUGH many persons know that a lot of type metal and etchings are used in the U. S. Government Printing Office few would expect to find anything on metals in the annual report of the Public Printer, George H. Carter. Yet the report for the fiscal year ended June 30, 1931, contains many interesting items. For example: Among the 57,500,000 lb. of materials and supplies delivered to the printing office was little new metal, but the metal in circulation is 6,000,000 to 7,000,000 lb. In the cost of production $31,523 is charged against metal, nearly one-third for salaries and wages. In miscellaneous sales were $4,696 from waste metal and $1,147 from waste gold (from books). Electrotype and stereotype covered 11,438,314 sq. in. The vaults and storage rooms contain 1,700,000 plates and 130,000 pages of type containing 4,600,000 lb. of metal valued at $275,000. In what was known as the Congressional Globe vault were 46,000 stereotype plates; these were salvaged by remelting for other platemaking service. The Congressional Record superseded the Congressional Globe in 1873.)

Jan 1, 1932

By Werner Langguth

SINCE the introduction of the improved method of precipitating gold from chlorine solution by SO2 and H2S at the Golden Reward chlorination-works, Deadwood, S. D.,* this modern method has been further adopted in the chlorination-works of the Portland Consolidated Company at Deadwood, and in those of the Black Hills Milling and Smelting Company at Rapid City, S. D. It has proved practically most successful in the handling of large quantities of gold solution, and constitutes up to date, with Mr. John E. Rothwell's most important improvement, namely, barrel-leaching under hydraulic pressure, the principal progress made in gold chlorination. The method of refining the gold sulphides which result from this method of precipitation, was introduced by me in 1890 at the Golden Reward works, and in 1892 at those of the Black Hills Company. It has not suffered any changes during the last three years, and is substantially as described below:

Jan 1, 1895

By R. R. Bryan

SINCE the first applications of cyanidation to silver ores about 1906, treatment of ores in the Pachuca district has been entirely by straight cyanidation. Until about the year 1921, Real del Monte removed a sulphide concentrate (largely pyrite) by tabling in the cyanidation grinding circuit. The ores milled prior to the year 1935 were dry ores, ideal for cyanidation, and yielded 90 pct of the silver and 92 pct of the gold. Since 1934 there has been a notable increase in the refractivity to cyanidation of the average ores received by the mill. Tonnages of the former amenable ores have gradually been replaced by tonnages of more refractory ones, so that present average recoveries have fallen to 83 pct of the silver and 90 pct of the gold. During this period there has also been an increase in the content of base metal sulphides' in many of the ores although this increase is not always directly related to the increased refractivity. Since March 1950, the Cia. de Real del Monte has been developing a flotation treatment for some-of its ores before cyanidation. Suitability for flotation is judged not only by the base metal content, but also by the amount of additional recovery of silver and gold made possible by the combined treatment. Selection and segregation of ores most suitable for flotation before cyanidation is a difficult problem for the mines, and the best that can be done is a compromise that leaves much to be desired. Development of Pre-cyanidation Flotation at Real del Monte Much laboratory work has been done on flotation of ores from the Pachuca district, however, the data could not supply reliable information on the many factors connected with the economics of low-base metal-high silver ores. Pilot plant operations would be required. Pilot plant facilities were made available in March 1950, when it became necessary to close down Loreto's 100 ton per day selective flotation plant because of exhausted ore supply. The results of the 100-ton pilot plant tests indicated that a large part of our tonnage of cyanidation ores could be profitably treated by flotation, and a tonnage of 1100 tons per day was selected as the maximum tonnage of ore that the mines were likely to deliver, and because this tonnage fitted with the grinding capacity of this circuit. Equipment was ordered for the production of a single flotation concentrate. The conception of flotation before cyanidation, at that time, was the production of a single concentrate to be shipped to the lead smelter. The 100-ton pilot plant was immediately increased to 350 tons by installing additional flotation cells.. This. plant was operated continuously until the 1100ton plant was put in operation in January 1951. In July 1950, an increase in the quotation for zinc called for an investigation- of the possibilities of producing a zinc concentrate, and laboratory tests on the tailings from the 350-ton plant indicated that a

Jan 1, 1952

By R. L. Dietrich

Magnesium alloy sheet has less ability to accept bending at room temperature than most of the heavier metals. In work designed to improve the bend properties, the preferred orientation of the sheet is of major importance as it is in all studies of the properties of wrought magnesium products. When rolled into sheet, all of the common magnesium alloys form an orientation texture having the basal (002) planes approaching parallel to the surface of the sheet. This texture is only slightly affected by annealing. Magnesium single crystals are highly anisotropic, and, as might be expected, so are magnesium alloy wrought products in which a strong preferred orientation is developed. It is therefore not surprising that bend properties are affected by orientation. Ansel and Betterton1 reported that the orientation of AZ3lXt sheet varies from surface to center and that bend properties are improved by etching away the sharply oriented material at the surface of the sheet to reach the more broadly oriented structure below. This paper covers a study of that orientation, either during the rolling process or by treatment of the finished sheet, in an effort to improve the bend properties and toughness of sheet. Literature The orientation texture of magnesium and magnesium alloy sheet has been studied extensively. Early determinations2 showed that pure magnesium sheet has a preferred orientation in which the basal planes are parallel to the sheet surface within very narrow limits. J. C. hIcDonald3 and J. D. Hanawalt4 reported that sheet containing a small amount of calcium develops a "double" texture, that is, the majority of the basal planes are a few degrees from parallel to the surface and there is a noticeable vacancy at the parallel position. Bakarian5 made careful quantitative pole figures of both pure magnesium sheet and MI alloy SEPTEMBER 1949 sheet which show these features. In all of these studies, however, the orientation was determined by transmission methods in which the resulting pattern is an average through the thickness of the sheet. The tendency of wrought metal to exhibit a different orientation at the surface from that in the center has been reported by many investigators. G. von Vargha and G. Wasserman6 found that with copper, aluminum, iron, and brass the textures of rolled compared to drawn wires were the same at the center but differed markedly at the surface. It was also reported by investigators7 that the orientation of rolled aluminum varies from surface to center. Har-greaves8 found that the surface texture of AM503 (magnesium alloy similar to MI) sheet was different from the center texture. It is reported by Edmunds and Fuller9 that zinc alloy sheet sometimes had a thin layer at the surface with a strong orientation of the basal planes parallel to the surface, which, if present, impaired the bend properties of the sheet. Part1 Surface Orientation ofMag- nesium Alloy Sheet and the Effect on Properties Attempts to correlate the bend properties of magnesium alloy sheet with tension ductility over short gauge lengths proved unsuccessful and the subsequent investigation showed that nonuniformity in orientation is a con- tributing factor as the properties of the surface material have a much more important effect in bending than in tension. A program to study the relationship between surface orientation at the surface and bend properties was then undertaken. First, the effect of etching away the surface of sheet on the bend properties and the orientations at the various depths were studied. Sheet samples of M1, AZ31X, and AZ61X were etched in dilute nitric acid to remove the surface material for various depths to 0.015 in. As may be seen in Table 1, the minimum bend radius improved considerably as the surface layers were etched away but it was necessary to etch the sheet quite deeply, much more so than was found necessary by Edmunds and Fuller9 on zinc sheet. It is also apparent that the amount of etching required is a function of the sheet thickness. In all of this work, radii were measured as R/t, the radius divided by the sheet thickness, in order to eliminate the effect of the reduction in sheet thickness produced by the etching. To determine the orientation texture of the sheet, X ray reflection patterns were taken using copper radiation with the bearn striking the specimen at an angle of 17' to the surface, which is the Bragg angle for the (002) planes of magnesium. Two exposures were made of each specimen, one with the beam perpendicular to the rolling direction and the other with the beam parallel to the rolling direction. The symmetry of the preferred orientation in magnesium sheet is such that these two photographs gave an approximation of the pole figure sufficiently accurate for qualitative work and it was not thought worthwhile to make complete pole figures. These X ray patterns show that the orientation has a much narrower spread at the original surface of the sheet than below the surface. The narrow spread is found in sheet having the majority of the basal planes (002) parallel to the surface, and since this is an unfavorable position for slip, it is

Jan 1, 1950

By Phillip A. Stoll, Young Ku Yoon

ThE deterioration of the magnetic properties of silicon-steel core materials during service (magnetic aging) is quite undesirable. Although some information about the effects of impurity elements on magnetic properties is available, 1,2 magnetic aging that occurs at low temperatures has not been extensively studied. Moreover, the microscopic techniques used by earlier workers were not suitable for study of fine metastable phases that are precipitated at relatively low temperatures. Recently, several investigators3,4 successfully used transmission electron microscopy in the study of low-temperature precipitation in Fe-C, Fe-N, and Fe-Mn-C alloys. To investigate metallurgical factors that affect magnetic properties after aging, the microstruc-tures of steels having different magnetic-aging

Jan 1, 1964

By C. Gatlin, F. Armstrong, K. E. Gray

This paper presents some preliminary results of two-dimensional cutting tests of dry limestone samples at utmospheric pressure. Cutting tips having rake angles of + 30°, + 15", 0°, - 15" and - 30" were used to make cuts on Leuders limestone samples at six depths of cut ranging from .005 to ,060 in. at cutting speeds of 15, 50, 109 and 150 ft/min. The vertical and horizontal force components on the cutting tips were recorded with an oscilloscope equipped with a polaroid camera. Motion pictures of the cutting process at camera speeds of 5,000 to 8,000 frames/sec were taken at strategic points in the variable ranges. The movies provide considerable insight into the brittle failure mechanism in rocks. It appears that chip-generating cracks usually have an initial orientation which is related to the resultant of the externally applied forces. The latter part of the crack curves upward toward the free surface being cut, this part being governed by some type of cantilever bending or prying. The linear and angular motion of the loosened chips also indicate the tensile nature of brittle failure. Analyses of the forces on the cutting tips indicate that: (I) relatively small increases in vertical loading result in large cut-depth increases for sharp tips (rake angles 2 0"); (2) tool forces increase at an increasing rate as the rake angle decreases, particularly for rake angles < 0"; and (3), for the range of this study, rate of loading had little effect on the maximum forces. Both the movies and visual inspection of the cuttings indicated that the volume of rock removed by chipping was much larger than that by any grinding mechanism, even for tips having negative rake angles. Cutting size increases with increased cut depth and rake angles, and decreases slightly at high cutting speeds, the depth of cut having by far the most influence. The amount of contact between the rock and the cutting tip was always less than the depth of cut and rarely exceeded 0.010 in. even for cuts of 0.060 in. INTRODUCTION The planing (or slicing) of various materials with a fixed blade has long been practiced by workers in many industries. For example, the farmer&apos;s plow, the carpenter&apos;s plane and the housewife&apos;s paring knife all employ this basic action. The casual observer might suspect that something so common must be quite simple; however, as in all problems involving the failure of materials, such is not the case. Industries concerned with the machining of metals have long studied these problems, and their literature on the subject is voluminous. Despite these efforts, basic knowledge is not very advanced, as may be noted from recent and comprehensive analyses of their literature.12 Metals are more subject to analysis by classical theories of elasticity and/or plasticity than are rocks, since their elastic constants and strengths are reasonably well established in many cases. In spite of this relative "simplicity", Hill9 refaces his discussion with an admission that the mathematical solution to the machining problem is not known. Photoelastic studies of both machining and milling have been performed and are discussed thoroughly by Coker and Filon.4 Rotary drilling of rocks with fixed blade or drag bits has long been practiced by the mining and petroleum industries, and considerable study has been given to defining their cutting action in terms of the pertinent variables. Essentially all the published mechanistic research on drag-bit drilling has been performed by mining engineers and has been concerned only with rocks in the brittle state. Fairhurst5-7 has worked extensively in this area and employed photographic techniques quite similar to those reported here, except at much lower speeds. His studies showed the periodic or cyclical nature of the brittle failure mechanism, in which instantaneous loads on the bit varied from some maximum value to near zero. Goodrichs has presented further data on the subject as well as a qualitative description of the process. Again the postulated mechanism is cyclical, with alternate chipping and grinding periods. The ploughing of coal is a practiced method and has been studied in some detail by English mining engineers."" Their findings have considerable general application to drag-bit drilling. Evans," in particular, has extended Merchant&apos;s metal-cutting theory" to brittle materials with some success, although certain aspects of his theory are open to question. Fish13 has recently summarized nearly all the published works concern-

By Haley, D. F.

WHEN operations were first started at Climax in 1917 by the Climax Molybdenum Co., they were pioneering in the molybdenum industry for little was known relative to the uses of molybdenum or the metallurgy of molybdenite concentration. Concentration of molybdenite is relatively simple today but in 1916, when the Climax deposit first attracted attention, it presented serious difficulties. Little was known, in fact, even about the assaying of such low-grade molybdenum ores. Mine samples were sent to at least a dozen of the best laboratories in the United States and average values reported varied from 0.4 per cent to 1.0 per cent MOS2. Owing to the wide variations in MoS2 content obtained from reliable chemists, the actual value of the ore was most uncertain. This variation occurred repeat¬edly over a period of six months in 1917. It was finally decided, as a last resort, to cut several tons of sample from the tunnel and have a mill test made, using the recovered MoS2 per ton as the grade of the ore, for a small error in the assaying of the concentrate would not materially affect the results. These mill tests were made by the General Engineering Co. (Callow) at Salt Lake City. The results proved an ore of commercial grade and indicated the flotation process for the best metallurgy. Based upon these tests, the decision was made to build a 200-ton flotation plant. At this time, the art of flotation was

Jan 1, 1946

By D. P. Seraphim

Single crystals of bee Li-Mg solid solution were grown and their internal friction was measured as a function of temperature, A peak of the Zener type was found in the damping spectrum. The activation energy for the relaxation process is 21.5 ± 1 kcal per mole and the frequency factor is 1015.7 ± 0.7 sec-1. ZENER internal-friction peaks which are observed for a wide range of solid solutions are attributed to stress-induced changes in local order.&apos; In the present work a Zener internal-friction peak, the first reported for a solid solution of an alkali metal, is

Jan 1, 1961

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.&apos; The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898&apos; C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942