Search Documents

By J. B. Bassett, E. S. Rowland

INTRODUCTION THE experimental work reported herein was inspired by the publication of a paper by Grange and Stewart,1 in which it was suggested that at low chromium contents the effect of this element on the [M,] point was greater than at higher chromium contents. It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the [M,] point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature. Such enrichment of the austenite in chromium content would lower the [ M,] point nearer room temperature where cracking is more likely to occur. Accordingly, it was decided to investigate the effect of chromium, in quantities between o and 2 pct, on the[ M,] point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the [M, ] temperature values were corrected by means of the Grange and Stewart formula§ to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (2) Hypereutectoid compositions: 1.00 pct carbon and 0.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased errors such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question of the effect of chromium on the [M,] point, particularly at low chromium contents. While it is fairly well established that chromium causes the [M,] to be lowered when present in quantities of I pct or more, Grange and Stewart1 have suggested that in small amounts (less than I. pct) it is more effective in lowering the[ M,] point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the []M,] point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the-[M,] point of a 0.20 carbon steel. MATERIAL Two series of 35 lb induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0.25 pct increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1948

By H. A. Wheeler

That lead and zinc deposits are the result of prolonged,, slow deposition is the idea of most students of ore deposits, and in many cases, where the ore-bearing solutions have been very weak or the precipitating conditions have been very feeble, the ore accumulations have undoubtedly taken a long period of time. As these two vital conditions have been subject to great variations in the different mining camps, the following example is highly interesting in showing that deposition can be very rapid under favorable conditions, geologically speaking, and also extremely recent. In fact, the writer is inclined to regard most, if not all, of the Mississippi Valley deposits of lead and zinc as probably being very young, at least not older than Tertiary, if not Quarternary, in age. The extensive Joplin lead and zinc district, in southwestern Missouri, which is about 60 years old and has numerous mines that were abandoned from 1 to 50 years ago, shows that the lead and zinc today are in an active condition of solution and redeposition, although these two metals occur in the predominant form of sulfides. The mine waters from the older and more or less abandoned portions of the district are frequently so acid, mainly from the oxidation of associated pyrite, as to necessitate the use of wooden pipes and pumps. The first boom in the Oklahoma zinc fields, which is the southwestern extension of the Joplin district, occurred when ore was accidentally struck in drilling a water well. Among the mines then opened up was the Mission mine, at Lincolnville, Ottawa County, Okla. This mine was opened in 1903 in lean "sheet ground," or a flat blanket formation of chert carrying disseminated zinc blende, or "jack," and galena. Theore-body was very free from iron pyrites and the concentrates were very high grade, the "mineral," or lead concentrates, assayed 80 to 85 per cent. lead and the jack, or sphalerite, assayed 60 to 65 per cent. zinc. The orebody was very shallow, occurring at a depth of 76 to 95 ft. (22 to 28 m.) and very wet, requiring three or four pumps to handle the water. The mine was operated until 1914, when it was closed by litigation and immediately filled with water. The second Oklahoma boom, five years ago, opened up the large, active camps of Picher, Tar River, and Century, which are located 2 to 5 mi. west of Lincolnville. They are considerably deeper, being farther down on the westwardly dipping monocline that emanates from the Ozark

Jan 1, 1920

By R. F. Hollis, C. K. McArthur

PRIOR to the application of anion exchange, all recovery of uranium from acid leach liquors precipitated an impure product requiring further upgrading before it could be refined. The ion exchange process, on the other hand, provides excellent selectivity for extracting soluble uranium from leach liquors, so that high grade concentrates can be produced directly. The discovery that uranium is readily adsorbed by anion exchange resins, together with the experience of resin and equipment manufacturers in water treatment, led to rapid development of ion exchange in a multiple column operation. Many processing plants using fixed bed ion exchange are in operation or under construction in Africa, Australia, and Canada. There are a limited number in the U. S. Although the fixed bed process has been highly successful, the feed to the ion exchange columns must be a clear solution, which is obtained by filtration or by countercurrent decantation of leached pulps. With some ores, poor filtration or settling characteristics make production of a clear solution difficult. Most processing plants in the U. S. receive their ores from a number of small mines, and there is considerable variation in the settling and filtering behavior of the ores. An ion exchange process was therefore desirable in which the uranium could be recovered directly for the leached pulp by adding ion exchange resin, which could be then separated from the pulp by a screening operation. The process would thus resemble the cyanide-charcoal process in which gold is adsorbed from cyanide pulp by means of activated charcoal. Preliminary tests in which leached pulps were directly contacted with resin beads led to the development of the RIP process.

Jan 4, 1957

By H. W. Smith, A. K. Bjerring

A nonlinear dynamic model for a flotation cell is developed, using a number of simplifying assumptions, the most important of which is that of essentially complete liberation in the feed material. Using this model, a complete dynamic model for a flotation circuit is developed and calibrated against steady- state process data. The dynamic response of the circuit to disturbances in input feed rate and composition is simulated, as is the response of a linearized and simplified model on which control design might be more easily based. Preliminary results indicate the practicability of the modeling technique. However, difficulties in matching steady-state operating conditions in one process stream, and the apparent importance of recycle streams as indicators of process operation, indicate that inclusion of at least one species of middling particle in the model should be considered.

Jan 1, 1969

By J. R. Cooper, A. Bruynesteyn

The final results of the operation of the Cananea test dumps are discussed. Scale-up factors between shake-flask tests, column tests and the large test dumps are established for the Cananea ore. The formation of clay layers, which formed inside the dumps and markedly affected extraction, as well as secondary enrichment, are discussed.

Jan 1, 1974

By A. S. McCreath

Jan 1, 1884

By E. G. Schempp, W. A. Morgan

The influence of modifications in the molybdenum, vanadium and, to a limited degree, carbon and boron content to a basic composition of 5 pct Cr, 0.75 pct Mo, 1 pct V hot-work tool steel composition, was studied in respect to hardenability, grpain- coarsening temperature, and tempering charactevistics. Tensile, impact, and fatigue pvoperties were studied for the most promising compositions. An alloy with a typical composition of 0.43 pct C, 4.97 pct CI-, 0.33 pct Si, 2.25 pct Mo, and 1.00 pct V uas found to offer the most favorable combination of properties in respect to high-strength applicntions when tempered at 1100°F. MANY 5 pct Cr high-strength steels are at present being manufactured in North America which fit well into the classification of the AISI-SAE system. Much interest has been shown in these materials as ultra-high-strength steels for use at elevated temperatures. The limiting temperature of use lies at the point where the steels begin to soften rapidly. Although a great deal of information has been made available in the past two years on the properties of selected alloys in this series, little information exists on the effect of systematically varying the ccntent of one or more elements in the 5 pct Cr-base alloy. This paper presents the results of an investigation of the effect of variations of the carbon, molybdenum, vanadium, and, to a limited extent, the silicon, manganese, boron, and niobium content of a 5 pct Cr steel to the AISI H-13 base analysis. EXPERIMENTAL PROCEDURE All experimental heats were melted in a 50-lb. induction furnace. The melting stock consisted of

Jan 1, 1962

By M. G. Taverner

Research was conducted into cold briquetting dross arisings and metallurgical coke fines from an Imperial Smelting Furnace (I.S.F.) as an economic means of agglomerating fine materials for smelting in a blast furnace. A mechanism was postulated whereby strong bonds were developed within the briquettes; laboratory scale smelting trials and full scale plant trials are included in the paper with a description of a two tonne/hour briquetting pilot plant. Benefits from smelting briquettes in an I.S.F. were measured directly in metallurgical coke savings and, indirectly, by a significant improvement in sinter plant productivity.

Jan 1, 1977

Jan 1, 1911

By E. D. Meier

SINCE Dr. St. Albans, in 1840, began to build successful watertube boilers—some of which are still in use—the gravity-return water-tube boiler has been built in many forms, more or less familiar to all who have studied the subject. A single firm in this country published recently a pamphlet, showing some fourteen modifications of their boiler during about as many years. There were hence available to the thoughtful inventor of this latest form many data showing what forms were to be avoided, as well as the effects sure to follow certain erroneous methods of construction in the older types. Improvements in materials, tools, and workmanship made possible, forms formerly prohibited by excessive cost. The first Heine boiler was built by A. Borsig & Co., for the

Jan 1, 1886

Executive Committee. ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. TIMOTHY W. SPRAGUE. HENRY A. WENTWORTH. AUGUSTUS H. EUSTIS, Secretary, 131 State St., Boston, Mass. The twelfth meeting of the Boston Section was held at the Engineers' Club, 2 Commonwealth Ave., Boston, on Monday evening, May 5, 1913, fifteen members and three guests being present. The meeting was called to order by Vice-Chairman Albert Sauveur, who introduced the speaker of the evening, Utley Wedge, of Ardmore, Pa. Mr. Wedge read his paper on the chloridizing roasting of copper ores, which he illustrated with a stereopticon, and which will be published in full by the Institute. After Mr. Wedge had closed his paper, which was received with great interest by all the members, the following discussion took place: Professor Hofman said that iron was formerly thought to ho essential to the Henderson process, but that it is not absolutely essential. Mr.Wedge said that, as far as he. knew, the presence of some sulphates was an abso¬lute necessity, and that line ores can be worked satisfactorily, although lime has an effect on the subsequent leaching. He added that the low fuel consumption of the latest Wedge furnace is a result of direct application of the combustion gases to the ore. Ten per cent. of fuel was needed with the muffle furnace. By direct firing he has been able to reduce the fuel needed to from 2 to 4 per cent. In the latest types of furnaces the gases from the upper hearth are not used. There is doubtless some temperature at which the loss. from copper chloride volatilization becomes serious, but in practice on Rio Tinto ores troublesome losses are not experienced. The copper apparently does not become volatile at. the temperatures where we would expect that it would. There are doubtless ores in which there would be serious danger from losses from this source. The latest furnaces do not use the high temperatures that were needed in the former single-hearth Wedge furnaces.

Jan 7, 1913

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers' determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

By L. S. Darken, H. A. Wriedt

An investigation has been made of nitrogen absorption by the lattice defects in a low-carbon steel afte~ Plastic deformation. Specimens in which defects were distributed by various combinations of cold rolling and vacuum heat treatment were equilibrated with controlled ammonia + hydrogen mixtures at 300° to 450°C to study the relation between the solubility and the thermodynamic activity of nitrogen. The results are interpreted in terms of nitrogen being absorbed upon two different types of defect sites, called A sites and B sites. The concentrations of these sites are calculated for specimens with various histories of straining and annealing; and the thermodynamic relations descrihing the equilibrium distribution of nitrogen among the A, B, and ordinary interstitial sites in ferrite are evaluated as follows: THE generalization that the solute atoms in a solid solution interact with imperfections in the solvent lattice is now universally recognized and the subject of an extensive literature. All types of imperfections—point, line, or surface—exhibit these interactions, but the relative importance of each type depends upon its concentration, the strength of its interaction with the particular solute atom, and whether the interaction is attractive or repulsive. The strength and sign of the interaction vary with the vectorial displacement of the solute atom from the imperfection in the crystal. The concentration of lattice defects increases during plastic deformation and the effect of the imperfections upon the solute atoms is usually perceived only after cold work or irradiation. Two experimental methods have previously been used to observe the effects of interaction between nitrogen atoms and lattice imperfections in a iron. Internal friction, which was first used for this purpose by Dijkstra,1 has been applied more often than the electrical-resistivity method of Cottrell and Churchman.2 The method of the present investigation has not been used before.* Uniform specimens of steel with a metastable defect structure are produced by cold rolling and subsequent heat treatment below the recrystallization temperature. Variations in the defect structure are obtained by varying the amount of strain and the heat-treatment conditions. The specimens are then saturated with nitrogen at moderately elevated temperatures in ammonia + hydrogen mixtures having various thermodynamic activities of nitrogen below saturation with Fe4N. From the nitrogen contents of analyzed samples, the metastable equilibria of interactions between the defects and nitrogen can be established and the concentration of sites for nitrogen atoms in the lattice defects calculated. A steel was used in the present experiments instead of purified iron or iron alloys because the amount of nitrogen absorbed at defects is larger in the steel over a much wider range of experimental conditions and could therefore be measured more accurately. The effect of alloy composition is discussed in Part II of this paper; it is sufficient to say here that impurities and phase heterogeneity in ferritic alloys favor the generation and/or retention of larger defect concentrations during plastic deformation and annealing at 300° to 500°C. MATERIALS AND EXPERIMENTAL PROCEDURE The experimental specimens were prepared from stock of a low-carbon steel, which will be called "X steel" here, with the composition: C, 0.12 pct; Mn, 0.43 pct; P, 0.010 pct; S, 0.034 pct; Si, 0.007 pct; As, 0.086 pct; Cu, 0.022 pct; Ni, 0.009 pct; Cr, 0.003 pct. The stock was all from a single ingot made by the basic open-hearth process, which was hot-rolled to strip 0.080 in. thick.. This hot-rolled strip, given the code designation "XH", was the starting material for preparing a series of cold-rolled sheets. The latter are designated "XC27",

Jan 1, 1965

By L. A. Roe, E. A. Elevatorski

Wollastonite, named after William H. Wollaston, an English chemist, is a calcium metasilicate, CaSiO3; CaO: 48.30%, SiO2: 51.70%. It has a short history as an industrial mineral. The earliest production of wollastonite is reported to be from a deposit near Code Siding, located north of Randsburg, CA. At this locality small tonnages of wollastonite were quarried during 1933-34 and 1938-41, and processed into mineral wool. This operation was largely experimental and virtually no United States production was again reported until the 1950s when a large deposit near Willsboro, NY, was developed by the Cabot Corp. A processing plant was placed onstream in 1953, with nearly continuous production to date. It is currently operated by NYCO, a division of Processed Minerals, Inc. Since 1958, wollastonite deposits in the Little and Big Maria Mountains of Riverside County, and in the Panamint Range of Inyo County, both in California, have operated intermittently for production of both ornamental and commercial wollastonite. During 1980, the United States was the major producing country, furnishing about 75% of the world's output. Current production comes from Finland, Mexico, India, and Kenya. Small amounts have been shipped intermittently from the USSR, New Zealand, Republic of the Sudan, Republic of South Africa, and Namibia (South-West Africa). The principal use of wollastonite is in the manufacture of plastics. Other uses are for paints, ceramics, adhesives, fluxes, glazes, thermal insulation board, and refractory products. Mineralogy Pure wollastonite, CaSiO3, has the composition of 48.3% CaO and 51.7% SiO2. However, it is seldom found in the pure state due to the ease with which it takes into solution the metasilicates of manganese, magnesium, iron, and strontium. Predominantly, wollastonite occurs as a contact metamorphic deposit forming between limestones and igneous rocks. Commonly associated minerals are garnet, diopside, epidote, calcite, and quartz. It has a specific gravity of 2.8 to 3.0, and hardness of 4.5 to 5 on Mohs' scale. When pure, it has a brilliant white color, but with impurities it may be grayish or brownish. Luster is vitreous to pearly. Melting point of wollastonite is about 1540ºC. Wollastonite occurs in coarse-bladed masses, rarely showing good crystal form. It is usually acicular or fibrous, even in the smallest of particles. The most unique property of crushed and ground wollastonite is its cleavage. Fragments of crushed wollastonite tend to be needle-shaped, imparting a high strength, and this property is the basis for many of its uses. The fiber lengths are commonly in the ratio of 7 or 8 to 1, length to diameter. The average diameter of wollastonite is 3.5 µm. Some crystals of wollastonite fluoresce under short-wave or longwave ultraviolet light, or both, with colors ranging from yellow-orange to pink-orange. Specimens may also show phosphorescence. The acicularity of wollastonite is a property of considerable importance to the marketplace. The plastics industry makes utilization of high aspect ratio grades of wollastonite (20:1) for reinforcing thermoplastics and thermoset polymer compounds. The naturally high pH of 9.9 (10% water slurry) is a prime property to the coatings industry. The coatings industry uses milled grades of wollastonite as a pH stabilizer in interior and exterior PVA and acrylic latex systems. Processed wollastonite can have a G.E. brightness of 90 to 93. Chemically, wollastonite is inert and this property makes it useful as a filler and reinforcing agent. There are two polymorphs of calcium silicates: wollastonite, a low temperature form, and pseudowollastonite, a high temperature

Jan 1, 1983

By J. B. Clemmer, F. D. DeVaney, H. A. Doerner

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 6oo,ooo lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaCO3) and dolomite (MgCO3CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent Si02, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 Si02 and 6.5 R203. The percentage reported as R203 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe203, A1203 and Ti02. The sorted magnesite product is not the best grade, even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1940

By S. Forgeron, W. Shaw, E. L. Zodrow

Trend-surface equations are proposed for volumetric coal estimation in collieries of Sydney Coalfield, Nova Scotia. The statistical technique was first tried on Harbour coal in #20 Colliery investigating resulting residuals for abnormalities. The trend model is accepted as probably being correct as a result of that investigation. Indeed, higher degree polynomial trend- surfaces account for over 80% of the total map variability; these are encouraging statistical results, backed-up by geological knowledge about the coal seam, suggesting that the trend model has economic significance for an off-shore colliery developed to exploit the Harbour coal several kilometers east of #20 Colliery. Specifically, the need for additional offshore drill holes for the new colliery (excepting quality assessment holes) should be considered in light of a developed estimating model for the new colliery. The trend model also finds application in coalfields structurally more complex than Sydney Coalfield.

Jan 1, 1983

By W. T. Thom

Interest naturally attaches to fissuring and subsidence of the earth's surface, whatever the cause may be, and the induced movement and fissuring of the impervious strata overlying an oil sand is of even greater practical importance because of its bearing upon the recoverability of the portion of the oil not already extracted or extractable by ordinary production methods. It is probably true that significant ground movement induced by oil production occurs only in oil fields in relatively young formations, where the oil comes from incoherent or only slightly cemented sands and oil-soaked clays, but inasmuch as a great proportion of our "gusher" wells produce from "running" sands and yield a large part of the total oil output, it seems worth while to make an effort to inspire the collection and recording of data indicating the nature and magnitude of oil-field subsidence, both surface and subsurface. Goose Creek Field The single known instance in which the nature and magnitude of the surface subsidence incident to petroleum withdrawal has been accurately ascertained is that in the Goose Creek oil field of Texas, described by Pratt and Johnson.' There subsidence caused the submergence of a considerable area within the oil field, and, because the title to the naturally submerged lands of Texas rests in the State, it became necessary to determine whether the submergence was due to natural or artificial causes. A detailed study revealed that the sunken area conformed very closely to the limits of the productive oil field and that the cumulative depression over an eight-year period ranged from zero at the margin to 3.25 ft. at the center. This depression was accompanied by the development of local marginal surface fractures along which the subsiding ares

Jan 1, 1927

By Keith Sutherland

AEROFLOAT 25 is a complex mixture of free cresylic acid with aryl substituted dithiophosphoric acids, sulphides, disulphides, etc. Its complete composition has not been published by the makers or patentees. It is prepared1 by the reaction between phosphorus pentasulphide and carefully selected cresylic acid. We have been informed that this acid contains no phenol and very little cresol, and that it is rich in the higher alkyl phenols, particularly the xylenols. The reaction between a phenol ROH and phosphorus pentasulphide may produce compounds of the following type:2 (i) RO S P Diaryldithiophosphoric acids RO SH (ii) R-SH Thiophenolic compounds (iii) R-S-R Diaryl sulphides (iv) R-S-S-R Diaryl disulphides (v) Substituted thianthren compounds Except for the simplest type, the thiophenols (ii), the boiling points of these compounds lie above 300° C. The amounts of the thianthren compounds formed from the five xylenols (if all these are present) will vary according to the position of the substituents. In an attempt to ascertain something of the nature of the reagent, fractional distillation under atmospheric pressure was undertaken. At the outset, hydrogen sulphide was freely evolved, and-particularly below 200° C.-the fractions had the strong odor characteristic of the

Jan 1, 1939

By Milton C. Head, Aulton E. Roland, William E. Hawes

INTRODUCTION Uranium mining in the Grants Mineral Belt has undergone changes from methods pioneered during the 1950's and has now become fairly standardized throughout the district. The orebodies vary in size and shape and have been most successfully mined by using modified room and pillar methods with pillar recovery. This paper will expand on methods and equipment that are being used and modifications of these that will increase productivity and efficiency. GEOLOGICAL BACKGROUND The petrology of the Grants Mineral Belt consists of alternating layers of sandstone and shales (mudstone), with occasional thin layers of coal. The sandstones are aquifers which are generally artesian to some extent. The shales are bentonitic and decompose into extremely sloppy mud when exposed to water. Figure 1 shows a typical geologic section. Most of the uranium produced in the Grants Mineral Belt comes from the Westwater Canyon member of the Morrison Formation and occurs as scattered ore bodies throughout the formation. This formation consists of layers of bentonitic shale and sandstone of varying degrees' of cementing and grain size. It is also a very significant artesian aquifer. The unconfined compressive strength of the various formations is not high, as shown in Table I. It is important to note that these represent average values and a great range may exist within a single formation, especially In the Westwater which is the ore formation. [ ]

Jan 1, 1982

By Kenneth Cottingham

The number of wells completed in Ohio during I940 was about 20 per cent more than during the preceding year, the comparative totals being 1020 and 1228. Of the 1940 completions, 327 were oil wells, 491 gas wells, and 410 dry. The completions for the past five years, divided into oil wells, gas wells, and dry holes, are shown in Table 2. Wells drilled deeper and input wells in water-flood areas are not included in the tabulation. The annual production of oil has decreased steadily in Ohio from the maximum of 23,941,000 bbl. produced in 1896. Table 3 shows the quantities of oil produced in the last five years. In 1940, the total was 3,052,000 bbl., produced by about 25,500 wells. The number of wells and the approximate quantities by grades are shown in Table I. Table i ,—Tabulation by Grade Grade 1 2 Barrels __________________________________________________________________________________________ Pennsylvania ............. . 1,198,000 Lima.................... . 325,000 Corning................... 3,730 1,159,000 Lodi...................... T,040 350,000 Cleveland................. 30 1:1,000 Total................... 25,500 3,052,000 The prices paid for Ohio crude oil in 1940, together with dates of changes in posting, are shown in Table 4. The production of natural gas in 0hio has declined from a maximum of 79,510,032 M cu. ft. in I9I5 S to 36,469,000 M cu. ft. in 1939, the most recent year for which a figure is available. Consumption reached its peak in Ohio in the year 1916, when it was 169,480,01r M cu. ft., declining to 114,720,ooo M CU. ft. in 1939. The produc-tion and consumption of natural gas in Ohio for the past five years are shown in Table 5. TAble 2.—Completions in Ohio during Past Five Years Numbs of Wells Drilled during Year YearI, ] Oil Gas Dry Total 1936............. 263 570 324 1,157 1937............. 317 503 45I 1,271 1938............. 189 433 288 gro 1939............. I70 501 349 1,020 19391940............. 327 491 410 1,228 Total.......... 1,266 2,498 1,822 5,586 Table 6 shows the number of oil wells and the number of gas wells completed by sands during 1940, with the average initial production per well for each sand. Table 7 shows the total number of wells drilled—oil, gas and dry—by sands. Development during 1940 Szth-Trenton.—For several years, considerahle interest has been shown in a horizon lying some 500 to 700 ft. below the top of the Trenton, known to the driller in western Ohio as the "green sand," and in eastern Ohio as the St. Peter. In 1939, ten 'lgreen sand" tests were drilled, all in western Ohio and all dry- In 19401 eight wells were drilled to this horizon, one of which was a small oil well (one barrel) in Men county- Of the remaining seven—all of which were dry-—one in Franklin County, in central Ohio, was drilled to a depth of 2903 ft. .Another was in Medina

Jan 1, 1941