Search Documents

By Richard F. Miller

The investigations of large-grained specimens carried out by Polanyi and Schmid,l Sykes,2 Goucher,3 Yamaguchi,4 Gough, Cox, and Sopwith,5 Carpenter and Elam,6 Aston,7 and others have shown qualitatively that grain boundaries restrain the deformation of adjacent crystals. But whether or not the influence of the grain boundary is confined to the glide planes intersected by the boundary has not been demonstrated in any of these investigations, nor has there been carried out any quantitative analysis of the influence of a boundary on the deformation of a crystal. Indeed, the specimens employed in the previous work contained so many complicating factors that it would have been difficult to observe any variation of the extent of the influence of the grain boundaries in relation to their sizc. The specimens were small, the grain boundaries irregular and at no particular angle to the specimen axis or the

Jan 1, 1934

By Charles H. Jacoby, Leo E. Read

IN diamond coring salt beds to evaluate deposits, special techniques are applied to standard slim hole drilling to obtain a representative sample of the water soluble sodium chloride. Industrial consumers generally require a run-of-the-mine material of 98.0 pct sodium chloride. Since no commercial beneficiation has yet been devised to upgrade the lower quality salt beds, the only processing is crushing and screening to the size required by the customer. Coring salt sections has recently become important not only in dry mining, but also in the development of brine cavities by hydraulic fracturing and the formation of jugs for storing liquid petroleum products. Drilling Fluid: The fluid used in coring salt beds in New York, Ohio, and Michigan is a thoroughly saturated brine made from 3.0 lb rock salt per gal of make-up water. This mined rock salt, -4 mesh +10 mesh, is dissolved in a lixator, a double-bottomed cone hopper that turns fresh water to fully saturated brine.

Jan 5, 1957

MINING ENGINEERING presents the annual membership report of the Society of Mining Engineers; see page 109.

Jan 7, 1963

By D. R. McCord

Data of a known statistical quality has been successfully used in a system of conventional fluid mechanics equations essentially free of empirical "conformance factors to prediet early detailed field 03 in a reservoir where gravity drainage is important and oil and rock properties vary con. siderably. The system is useful where comparative recovery predictions for one or more cases of natural depletion and gas cap pressure maintenance are needed and the reservoir is not too heterogeneous. INTRODUCTION Many authors, have examined various facet* of the gravity drainage-gas cap pressure maintenance problem over the last several years. Two of them. Burtchaell and Elkins, have published practical studies. In the case described in the present paper the best development and operating plan for one of the important reservoirs of the Bolivar Coastal Field in Western Venezuela was urgently needed. It was requested that sound comparative economics be presented along with an engineering evaluation of no additional drilling, maximum drilling. several cases of gas pressure maintenance, of water flooding and combination cases. A rapid analysis of the effect on recovery of the range of crude and rock properties indicated that none of the published methods using average properties would yield adequate comparative predictions. This paper covers the predictive system developed to deal with natural depletion and gas cap pressure maintenance. The large amount of data available for this field permitted statistically reliable correlations to be made of most rock and oil properties, and the evident smooth areal variations of these properties encouraged the construction of a lineal mathematical model of material balance and fluid flow equations, which could be manipulated by a modified iterative procedure. The manipulation is much more adaptable to computing machines than manually operated calculators and subsequent studies have been prepared for the IBM Card Program Calculator. A matrix as opposed to linear model has been tentatively worked out by other members of our group to deal with more heterogeneous reservoirs. It is more adaptable to computers such as IBM-701 or the Remington-Rand Univac. In 1950, when the system reported below was developed, no rapid computing machines were available to the author. Their existence and promise encouraged an initial approach by hand. Some details of oil and rock Property correlation are included because there are a surprisingly large number of medium-sized reservoirs in the world that show systematic property variations which are significant for a rigorous analycon. All large reservoirs (over half a billion barrels recovery) with which the author is familiar contain at minimum a significant temperature variation. Using the rock and oil property correlations, past pressure and production, the gas-oil ratio history of the reservoir was computed and found to be in close agreement with field measurements. The future performance under cases of natural depletion, gas injection of 100 MMcf/day, and of 130 MMcf/day, was then computed; a 70 MMcf/day case was also carried far enough to provide data for comparative economics. The 130 MMcf/day case proved to be the most attractive. A 50,000 horsepower gas turbine driven centrifugal compressor plant to take this quantity of adjacent field gas from 30 to 1,950 psia and inject it into the reservoir is under construction. The total cost of the project will exceed 20 million dollars.

Jan 1, 1953

By F. W. Bloecher

D ETERMINATION of the surface area of finely divided minerals is of interest to mineral engineers engaged in flotation, comminution, and dewatering studies. In the industrial minerals field, many materials are classified as to fineness according to their specific surface (surface area per unit weight). A method of surface area determination has been tested and used in the Richards Mineral Engineering Laboratories at M.I.T. It involves low temperature krypton adsorption measurements using the technique described by Beebe.1

Jan 3, 1951

By James K. Stanley

PREFERRED orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.1 In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurgical literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanical properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important in- formation, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational under- standing of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing 'stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required-it is only necessary punch or machine a disk of the sheet material and insert it into the testing device.

Jan 1, 1943

By W. A. Ver Wiebe

The year 1938, with a production of 58,784,250 bbl. from 18,790 wells shows a slight recession from the high peak of oil production reached the previous year, when slightly over 68 million barrels of oil was marketed. The previous high peak had been reached in 1917 with a total of 45,451,000 bbl. Another still earlier peak was reached in 1904, during which year slightly less than 5 million barrels was produced and sold. The production of gas, on the other hand, probably reached a new peak during 1938 with a total of over 60 billion cubic feet. This peak, however, was not the highest peak, for during the year 1908 over 80 billion cubic feet was produced. Between these two high peaks the production dropped down to 16 billion cubic feet in the year 1921. The number of wells drilled during the year totals 1569. This figure is somewhat lower than the figure given in several trade journals because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly three-fourths (or 1107) of the total number of wells were completed as commercial oil wells (915 in western and 192 wells in eastern Kansas). The commercial gas wells completed number 50, of which 4 are in eastern Kansas and 46 in western Kansas. The remaining 412 completions include 130 dry holes in eastern and 282 dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year accounted for 70,000 bbl. of new oil for eastern and 1,220,000 bbl. of new oil for western Kansas. It is interesting to note in this connection that the number of wells completed in the state rose gradualIy to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918 when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak in 1937, the low point was reached during 1931, with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a new area whether it should be called a new pool or a long extension of an

Jan 1, 1939

By W. A. Ver Wiebe

The year 1938, with a production of 58,784,250 bbl. from 18,790 wells shows a slight recession from the high peak of oil production reached the previous year, when slightly over 68 million barrels of oil was marketed. The previous high peak had been reached in 1917 with a total of 45,451,000 bbl. Another still earlier peak was reached in 1904, during which year slightly less than 5 million barrels was produced and sold. The production of gas, on the other hand, probably reached a new peak during 1938 with a total of over 60 billion cubic feet. This peak, however, was not the highest peak, for during the year 1908 over 80 billion cubic feet was produced. Between these two high peaks the production dropped down to 16 billion cubic feet in the year 1921. The number of wells drilled during the year totals 1569. This figure is somewhat lower than the figure given in several trade journals because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly three-fourths (or 1107) of the total number of wells were completed as commercial oil wells (915 in western and 192 wells in eastern Kansas). The commercial gas wells completed number 50, of which 4 are in eastern Kansas and 46 in western Kansas. The remaining 412 completions include 130 dry holes in eastern and 282 dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year accounted for 70,000 bbl. of new oil for eastern and 1,220,000 bbl. of new oil for western Kansas. It is interesting to note in this connection that the number of wells completed in the state rose gradualIy to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918 when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak in 1937, the low point was reached during 1931, with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a new area whether it should be called a new pool or a long extension of an

Jan 1, 1939

By Stuart H. Ingram

DEFINITION THE term lightweight aggregate implies material which may be substituted for the usual rock, sand and gravel commonly used as the major part of concrete, but distinguished by being much lighter in weight. BACKGROUND The art of making and using concrete is old and well developed. Research and experience have pretty well determined the qualities necessary in its constituents, and time has tested theories and applications. Elaborate specifications and tests have been devised and generally adopted governing all phases of concrete work, from selection of material, through engineering design and down to mixing and placing. Standard practices have become routine to executives and laborers, and operations have been simplified and costs lowered. Though many lightweight aggregates meet the basic specifications necessary for usefulness, their physical qualities are so different that they frequently will not pass standard tests, and some of them cannot be mixed and placed with the usual formulas for water and slump. As a rule their use produces a concrete with a lower modulus of elasticity which requires design change, and being produced in much smaller quantities than ordinary aggregate, production costs are higher. This latter works in a vicious circle to restrict their use and maintain prices that are not competitive, except as against each other. INCREASED DEMAND In spite of such handicaps consumption has grown steadily for the past two decades and is apparently growing even faster today. It is evident that lightweight concrete must have better qualities, and be sufficiently better to overcome the higher cost and the other difficulties and disadvantages pertinent to the use of a new and different material in an old industry. Hence the study of its main ingredient should be of interest to all engineers. Our group has a double interest in the subject since most of the materials which have been used as sources of lightweight aggregate are either mined, or are by-products of mining operations. We are directly interested in their production as well as their use, and since available supplies of materials suitable are limited, the increasing use, and rising demand, make the discovery of new sources, or the development of processes to adapt other natural materials to this use, a promising field; and one in which our profession should take an active part. RECENT DEVELOPMENT Descriptions of ancient work contain references to the use of spalls of tuffs or pumice in concrete masonry, but it is only since the nineteen twenties that serious attempts have been made to produce and market lightweight aggregates. A period of rapid advance in theory and practice in cements, mortars and con-

Jan 1, 1947

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Charles H. MacDowell

Up to 1909 the American public had little knowledge of, or interest in, potash. Some remembered that it had to do with soft soap and sore throat,, but further they knew not. In 1909-10, the German-American potash war, and the publicity attending hostilities, brought home to America the knowledge that potash was an important article of commerce; that Germany monopolized its production and distribution, and exercised all the prerogatives attending complete control. The present war, with its transportation embargo, has again directed attention to Germany's strength as a potash producer and her present unfortunate situation as a distributor. As a consequence, the search for potash takes on new life and it again becomes a subject of general interest. My first knowledge of potash came from a study of the German potash exhibit at the World's Fair in 1893. This investigation led to the recommendation that Armour & Co. engage in the manufacture of commercial fertilizers and the fertilizer branch was organized early in 1894. From then to now " potash " has been a live subject. Two and eight-tenths per cent. of the earth's crust consists of potassium oxide. It is an important constituent of feldspar, granite, and other igneous rocks. Potash is valuable commercially in a water-soluble form. In igneous rocks it is locked in so tight that it is of little value and no utilization in a commercial way has been made of these insoluble forms. Potash in water-soluble form is found in large deposits in Germany; in smaller deposits in Austria and Spain; and in brines in some of our Western arid basins. The deposits in Germany, Austria, and Spain are concentrations from sea waters containing potash derived from the decomposition of potash-bearing rocks. It has been found that the amount of potash remaining in decomposed rocks is not the same as that in the original rock. For instance, granite containing originally 5.58 per cent. potash contained only 1.49 per cent, in the decomposed rock. Syenite containing 6 per cent. in the original

Jan 1, 1915

By A. E. Gorum, I. Cornet

Fatigrle of ionic crystals has been studied primarily in magnesinm oxide. under cyclic stress dislocations move irrreversibly; they multiply; slip bands form and grow; cracks mucleate and propagnte, and failure occurs. The use of ionic crystals such as MgO is advantageorus in such investigations because they are optically transparent. Individual dislocation Intersections with {100} surfaces may be observed with a standard microscope, using etch-pit techniques. Slip, deformation, crack .formation, and fracture in MgO crystals under cyclic stress are compared with cotrresponditzg processes in metals. ThE effect of cyclic loading in metals has been studied for many years. The appearance of slip lines is readily observed and the ensuing fracture may also be seen. From these observations it is possible to predict the behavior of a material and make an educated guess as to what is happening internally, but the actual changes taking place within the structure are not readily apparent. If one could obtain a material in which the individual glide components could be observed, it would be invaluable in determining the actual slip distribution resulting from cyclic loading as well as the distribution of slip in the neighborhood of a growing crack. Such a material is magnesium oxide. Dislocation arrays may be observed by means of etch pits

Jan 1, 1961

By JOSEPH MACDONALD

STRIPPED of its romantic possibilities, mining is a commercial business, carried on for the profit there is in it, and the business of the manager, in its ultimate analysis, is to make the profit as large as possible. The general manager of a mining company should keep himself personally familiar with all the details of its operations. If be fails to do so, chaos results, labor becomes inefficient, costs go up, and profits go down. Nowhere is this emphasized more than in Mexico. If the mining operations are extensive and complex, involving, besides the work of mining the ore, its transportation and treatment by various milling operations, and the marketing of the products, the business, to be carried on properly, must be divided into a number of main departments, which are subdivided into minor departments. Each main department should be under the immediate charge of a superintendent, or a foreman, and each minor department under a shift-boss. Organized in this way, and with all the principal centers of activity connected by telephone, the manager can keep in touch at all times with the details of every branch of the business, and be in a position to perform effectively the full duty of manager. The ?total cost of mining operations may be broadly divided under the heads of Labor, Supplies, and Marketing. Of these, it will be found, on averaging a number of cases, that the cost of labor will be about two-thirds of the total cost. The importance, therefore, of an efficient labor-department will be apparent. This department must be sub-divided and organized differently, according to the peculiar conditions at each mine, and no one system, however well suited for one particu-

Jan 1, 1909

By Allen Rogers

THERE are few natural monopolies comparable with the nitrate industry. Perhaps the only other one is, curiously enough, also an essential fertilizer material, viz., potash, of which the Germans have heretofore held practically a-monopoly due to the existence in their territory of the most important known deposits of potash salts. And although nitrates in minute amounts are found in many desert regions, the only deposits callable of being worked commercially exist in Chile. Combined nitrogen in the oxidized form is an essential for plant life. Nature provides it mainly through the agency of nitrogen-fixing bacteria. But where lands are cropped artificially this supply is too small; and gradually the nitrogen supply becomes exhausted. In order to continue farming, it is necessary to furnish a supply of nitrogenous plant food, and this is clone by putting on various substances containing combined nitrogen. These consist of various animal wastes, ammonium sulphate, the ammonia of which is obtained in the destructive distillation of coal, and Chile saltpeter. The latter is immediately available as a plant food, the nitrogen being in the required form. The other substances must oxidize before they are available. Besides its use as a fertilizer, Chile saltpeter is the source from which the bulk of the nitric acid of commerce is derived. The use of nitric acid in the manufacture of almost, all modern explosives is, of course, well known.

Jan 2, 1918

By Edwin F. Nelson, Charles Wirth, Gustav Egloff, C. D. Maxutov

The treatment of emulsified crude oils has been a problem for years in the petroleum industry. Until comparatively recently various methods of settling with and without chemicals have been used with indifferent success. Since wells have been acidized, emulsified crudes have been produced, which add considerably to the need for improved methods of treatment. The presence of large quantities of salts in the oils from acidized wells has presented several new problems to the industry. The use of hydrochloric acid in well treatments has caused the formation of sodium, magnesium, and calcium chlorides by interaction with the dolomitic limestones. These salts dissolve readily in the water normally present in the oil, and they are therefore incorporated in the emulsified oil. The crystalline salts have also been found in the oil, prevented from settling by protective films such as asphalt, resins and petrolatum. In some instances, free hydrochloric acid has been found. The salts may be present in crude oil in amounts ranging from a few pounds to over 1000 lb. per 1000 bbl. of oil. The transportation of these crude oils through pipe lines has led to erosive and corrosive effects, which are a tremendous cost to the petroleum industry. During 1937, more than 1,200,000,000 bbl. of crude oil was transported through pipe lines. Of this quantity approximately 10,000,-000 bbl. was water, and considerably more than 50,000,000 lb. was salts. If the crude oils were treated at the producing wells to remove the salts and water, an appreciable saving would be possible. The treatment would not be difficult, since it has been found that these oils are more easily treated at the time they are produced than after the aging and more stable emulsification that occur before they reach the refinery. Since great costs are involved in the use of these salty crudes at the refinery, treated oils essentially free of salts would naturally command a premium. The real added costs lie in refining salt-containing crude oils. Severe corrosion of refinery equipment in both topping and cracking installations has appeared in many refineries. Chemicals such as ammonia, lime and

Jan 1, 1938

By D. M. Warner, Samuel Daniels

In this paper are given the mechanical properties, determined by the Engineering Division, Air Service, U. S. A., of the 94 per cent. aluminum, 5 per cent. copper, 1 per cent. silicon alloy as 8and-cast and as heal-treated commercially to Air Service Specification No. 11,300. This particular alloy was tested both in the cast and in the heat-treated condition. Tension and tension modulus values were obtained from machined and from un-machined test specimens; while data for shear, compression, impact, torsion, and for Brine11 and Rockwell hardness were found from machined bars. Specific-gravity tests were made on sanded, un-machined specimens. The metallography of the alloy is useful as a control to heat treatment and presents some interesting peculiarities in regard to the two iron-bearing compounds. The demand for an aluminum alloy, suitable for sand castings, that may be heat treated to meet requirements of high strength, ductility, shock and corrosion resistance, and ready machineability has led to the commercial development of a proprietary material that contains from about 4 to 5 per cent. of copper, 1 per cent. of silicon, and such impurities as iron, up to a maximum of 0.75 per cent., and manganese, in quantity usually less than 0.1 per cent.' Magnesium is not generally present, for it tends to nullify the beneficial influence of the added silicon by forming magnesium silicide. The function of the silicon is to minimize casting difficulties and, structurally, to favor the precipitation of (insoluble) iron-bearing skeletons rather than the needles, which prevent full realization of tensile properties from heat treatment by stimulating intergran-ular fracture. The amount of silicon necessary to counteract the ill effect of iron is equal to or slightly more than the content of iron; the excess of silicon over this ratio, under certain conditions of heat treatment, enters with CuAl2, the principal hardening constituent, into solid solution and contributes somewhat to the strength of the alloy without appreciably impairing its ductility. The schedule of heat treatment of this alloy depends on the design (cross-sections) of the castings and on the nature of the tensile properties desired. Essentially, the process consists in heating the material at about 950" F., quenching in oil or in cold or boiling water, and artificially aging

Jan 1, 1926

By Paul Merica

ALTHOUGH nickel was discovered and isolated as early as 1750 and its valuable properties recognized, many years passed before it was used commercially for wire, sheet, rods, etc., in the pure form. This was due partly to its high cost at that time and partly to the fact that it was not possible to refine and cast nickel into ingots sufficiently malleable to be amenable to the usual forging, rolling, or drawing processes. So remarkable was this fact, and so different from the experience at that time with metals such as copper and iron, that it has left its impress on the no-menclature within the nickel industry. To this day, furnace-cast nickel produced in such a manner as to be suitable for rolling and forging is called malleable nickel to distinguish it from the ordinary pig and shot nickel of commerce. In 1878, the firm of Jos. Wharton, of Philadelphia (which later became The American Nickel Works, a constituent of The International Nickel Co.) exhibited at the Paris Exhibition specimens of rolled pure nickel strip and of drawn nickel wire. About this time, there was considerable activity in the study of the refining of nickel and several methods were described, some of which were patented, for the production of furnace-cast malleable nickel including the use of manganese (Boed-dicker,1 Selve and Lotter2), the use of potassium permanganate (Bernsdorfer Metallwarenfabrik3) and the use of phosphorus (Garnier4). By far the most efficient method was discovered by Th. Fleitmann in 1879;5 it consisted in adding to the molten nickel, just before pouring the castings, from 0.05 to 0.125 per cent. of metallic magnesium. This soon became the recognized final malleableizing treatment for furnace-cast nickel.

Jan 1, 1925

By Volker Weiss, George Sachs, AE. P. Klier

PHYSICAL chemistry contributes to the understanding and efficient operation of hydrometal-lurgical processes in many ways, among them by providing quantitative answers to the following questions. 1) Can a given chemical reaction or process be made to operate and. if so, under what conditions? 2) what are the' factors which determine the rate of the reaction and how can this rate be regulated in practice? Thermodynamics attempts to answer the first of these questions and kinetics the second. The answer

Jan 1, 1958

By Howard S. Bryant

The year 1928 has recently.passed from the picture and it is at this time that the various divisions of the oil industry are giving thought to plans for the present year. The outstanding characteristic of the industry in 1928 was the successful curtailment of oil production to the market's needs. It has been thought advisable to look ahead and endeavor to anticipate the oil demand for the coming year, and thus determine the volume of oil that can be safely produced without causing major additions to surface stocks. The year has been one of smaller additions to stocks than in 1927, a record demand for oil products, and a further developed spirit of cooperation among oil producers, as well as various other achievements. It is well to pause and take stock of ourselves. Present Status of Crude Oil Supply and Demand The total daily new supply of oil is at this time1 about 2,960,000 bbl. per day, made up of 2,585,000 bbl. domestic crude production, 125,000 bbl. casinghead gasoline, and 250,000 bbl. of imports. With the present low consumption, due to the falling off in the winter season demand, it is estimated that about 150,000 bbl. a day are now being run to storage, and that the first three months in 1929 will see large-sized additions to storage. Consumption plus exports of oil have increased at a regular rate from year to year, and although oil production in 1928 passed the 1,000,000,-000 bbl. mark for the second time in the history of the United States, with a production of 25,000,000 bbl. more than in 1927, only 30,000,000 bbl. were added to storage during 1928. This is compared to an addition of 65,500,000 bbl. in 1927.

Jan 1, 1929